We serviced a
FRIGIDAIRE WALLOVEN
Model FEB27S6DCB
Near Colorado Springs, CO 80907
Jerimiah
Job Details: 01/13/2023
"Wasnt able to remove unit from wall, there is no slack on the incoming power cable, must access junction box in crawlspace underneath house in order to do so. However unit is stuck inside and cannot be released. Customer is going to contact CMR or possibly A&E factory to either get the unit removed and/or repaired.. Closing call. No charge due to inability to access unit."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, CO 80927
Aaron
Job Details: 01/13/2023
"Unit was not level, drain hose not tied, corrected issues and advised customer of usage of the unit. Explained high efficiency units. Working well now.Advised of 5 star survey"
We serviced a
SAMSUNG WASHER
Model WV55M9600AW/A5
Near Colorado Springs, CO 80909
Jim
Job Details: 01/13/2023
found the top drain pump is inop reccommend replace the drain pump customer declined repair
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHV0
Near Colorado Springs, CO 80927
Aaron
Job Details: 01/13/2023
"Water inlet valve hose clamp was not secured, cx states someone else had replaced the inlet valve. Tested unit, board keeping valve open too long on second fill, tub is overflowing. Needs board. Control board w11131683 $264.44Tax $21.68Hc $129.95Labor $159.95Total job$576.0230 day estimateAdvised of surveyAuth hc 129.95 #4LA9RU"
We serviced a
SAMSUNG DISHWASHER
Model DW80M9960UG/AA
Near Colorado Springs, CO 80906
Brandon
Job Details: 01/13/2023
"Lc error during cycle, could not locate active leak, took pictures of error codes, cx says this is the third repair and they are going thru their warranty to have replaced, found water marks on drain pump hose and leak sensor may be faulty"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Albuquerque, NM 87123
Jason
Job Details: 01/13/2023
"checked unit found roller keeper had come off, re secured roller unit checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDB02
Near Albuquerque, NM 87112
Jason
Job Details: 01/13/2023
installed door gasket and sealed cabinet to liner gaps unit checks ok
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Albuquerque, NM 87111
Jason
Job Details: 01/13/2023
installed lid lock unit checks ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Manitou Springs, CO 80829
Brandon
Job Details: 01/13/2023
Replaced parts and reset ice maker it cycled hass passed and sent asked cx to complete survey
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Albuquerque, NM 87122
Jason
Job Details: 01/13/2023
installed console unit opperation checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF736SDAW10
Near Albuquerque, NM 87113
Jason
Job Details: 01/13/2023
installed gasket unit checks okAuth code:WFXA94/$149-
We serviced a
GENERAL ELECTRIC RANGE
Model PHS930YP7FS
Near Frisco, CO 80443
Erik
Job Details: 01/13/2023
remove ui control panel and inspect harness(es) - comm cable fell out of harness - reconnect harness and reinstall ui control panel - test - goodcustomer education on proper pan sizing and cleaning cook top
We serviced a
JENN-AIR WALLOVEN
Model JJW2827IM01
Near Grand Junction, CO 81507
James R
Job Details: 01/13/2023
replaced lower oven bake element. replaced thermostat lower oven. replaced lower oven cooling fan. powered on. unit came up with F9E0 code Miswire issue and F2E0 UI not connected. pulled bottom drawer out below wall oven and found that the electrical wiring is oiutside of the electrcal box. believe drawer was hitting the wiring. cut pwr and tightened some of the connectors. oven is now working. customer needs to have an electrician come out and redo the electrical wiring. tested all functions. op's ok. normal operation. Please fill out whirlpool customer satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WFW6620HC3
Near Grand Junction, CO 81507
James R
Job Details: 01/13/2023
Install pads under rear and front adjustment feet. To try to keep it from moving around.Run unit with a load of towels. Quick wash. Unit still seems to shake quite abit with a load in it. customer will need to call whirlpool and request a different service company with two men to do repairs on unit. It will need a stand and may even need a basket tub asy.
We serviced a
SAMSUNG OVEN
Model NE63A6511SS/AA
Near Colorado Springs, CO 80920
Aaron
Job Details: 01/13/2023
Samsung tech support called as requested. Samsung will not cover warranty on a melted terminal block. Estimate approved on site. Replaced parts and tested unit. Heating well. Terminal block dg96-00173a $95.36Screws ea ?6 de60-10199a $13.50?6Total parts $176.36Tax $14.46Hc $129.95Labor $ 159.95Total job $480.72No return on parts
We serviced a
SAMSUNG WASHER
Model WA55A7700AV/US
Near Colorado Springs, CO 80910
Jonny
Job Details: 01/13/2023
"Installed part, unit works, custy is happy"
We serviced a
WHIRLPOOL WASHER
Model MVWB865GW0
Near Albuquerque, NM 87114
Joseph
Job Details: 01/13/2023
door is cracked at the left hinge. door wont close right. customer will need new door. unit is out of warranty. customer denied repair due to cost of repair but we did collect service charge of 129.95.Auth code:4TY34J
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FMDW09
Near Rio Rancho, NM 87124
Joseph
Job Details: 01/13/2023
installed parts listed. unit tested good. unit is good to go. let customer know to wait 24 hours for cooling.
We serviced a
WHIRLPOOL WALLOVEN
Model WOS31ES0JS01
Near Rio Rancho, NM 87124
Joseph
Job Details: 01/13/2023
install part listed unit tested good. unit is good to go.
We serviced a
VIKING RANGE GAS
Model n/a
Near Colorado Springs, CO 80906
Jerimiah
Job Details: 01/13/2023
"Customer was told to bring it in from garage and place it in the kitchen, literally was taken and placed right in the middle of the kitchen without any hook ups. Customer was not home at the time, cell was unable to charge customer. Wasnt able to diagnose unit. Closing call. Customer is aware unit needs to be installed prior to us coming out and have a card on file. Patrick and TK knows of this situation."
We serviced a
BOSCH DISHWASHER
Model SHPM78Z55N/20
Near Colorado Springs, CO 80906
Jim
Job Details: 01/13/2023
replaced the user interface the detergent dispencer and the door lock kit placed unit in rinse unit test ok
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HW08
Near Parachute, CO 81635
James R
Job Details: 01/13/2023
replaced control and control panel. test op's good.Please fill out whirlpool customer satisfaction survey. Thank You.
We serviced a
SAMSUNG WASHER
Model WF45T6200AW/US
Near Colorado Springs, CO 80928
Jonny
Job Details: 01/13/2023
"Installed part, custy is happy,washer works , it passed hass"
We serviced a
WHIRLPOOL WALLOVEN
Model KODE500ESS20
Near Peyton, CO 80831
Glenn
Job Details: 01/13/2023
"Customer ran self clean, then received error code (forgot what code was), Next day after the unit cooled, lower oven still working, upper oven not heating. Techline: F5E1 , Latch Assy Issue , Also suggest possible cause due to no bottom board under oven, just metal runners. If problem returns, suggest have installers correct install by installing a board under oven to allow proper air flow.SR#7735494074 , Found Bad TOD on Upper oven. Install New TOD, All OPS Test:OKWP4449751"
We serviced a
WHIRLPOOL DRYER
Model MEDX655DW1
Near Pueblo, CO 81005
James K
Job Details: 01/13/2023
Discussed survey. Installed ordered parts all ops test good
We serviced a
WHIRLPOOL REFRIGERATOR
Model GI6SDRXXQ03
Near Pueblo, CO 81005
James K
Job Details: 01/13/2023
Installed ordered parts all ops test good collected as 129.95 $129.95 CK Auth# 9RVCYR
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Albuquerque, NM 87107
Larry
Job Details: 01/13/2023
CX complaint - Not draining - Inspected unit and found the drain pump failed - Replaced with pre-id part and tested good
We serviced a
THERMADOR RANGE
Model PRG486JDG/12
Near Colorado Springs, CO 80921
Jerimiah
Job Details: 01/13/2023
"Installed replacement bake igniter. Unit check OK, charged labor as quoted. $167.95 CC Auth# 99RR9V"
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model GFE26JYMFS
Near Colorado Springs, CO 80905
Jim
Job Details: 01/13/2023
replaced the door handle clips unit test ok
We serviced a
MAYTAG DRYER
Model MED6500MBK0
Near Colorado Springs, CO 80925
Ken
Job Details: 01/13/2023
Dryer is working properly and Temps are in the correct range
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHV0
Near Colorado Springs, CO 80921
Aaron
Job Details: 01/13/2023
"Replaced parts and tested operation, cx confirmed, working well now. Advised of 5 star survey"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHW4
Near Colorado Springs, CO 80925
Ken
Job Details: 01/13/2023
Installed parts and tested discussed fcc survey
We serviced a
AMANA DRYER - ELECTRIC
Model NED5800HW0
Near Colorado Springs, CO 80906
Jim
Job Details: 01/13/2023
found the heat element open replaced the heat element unit test ok
We serviced a
GENERAL ELECTRIC DISHWASHER - BUI
Model GDT535PSJ2SS
Near Colorado Springs, CO 80927
Jim
Job Details: 01/13/2023
"replaced the main control and the flood switch, placed unit in the rinse cycle unit test ok"
We serviced a
WHIRLPOOL WASHER
Model WTW8040DW4
Near Peyton, CO 80831
Glenn
Job Details: 01/13/2023
"Install New Valve Assy, All OPS Test:OK"
We serviced a
WHIRLPOOL WALLOVEN
Model KOCE500ESS11
Near Colorado Springs, CO 80921
Jerimiah
Job Details: 01/13/2023
"Installed replacement mag and inverter. Unit check ok, did document damage found on old mag, and on waveguide. *****IF MAG NEEDS REPLACING WITHIN A YEAR FROM NOW CHECK WAVEGUIDE FOR FURTHER DAMAGE****** disclosed survey to cust FCC"
We serviced a
JENN AIR RANGE
Model JDRP436HL
Near Colorado Springs, CO 80919
Jerimiah
Job Details: 01/13/2023
"Installed replacement parts, Cust will keep track of unit functionality. Unit check ok. Disclosed survey to cust, fcc"
We serviced a
VIKING RANGE
Model VGIC3676BSS
Near Colorado Springs, CO 80919
Jerimiah
Job Details: 01/13/2023
"Cust was asking advice what to do about range, found one burner base igniter wire having insulation issues. Removed burner bases bypassed igniters and shown that the wires did have spark thru wire but stopped at igniter pin Cust will order burner base with igniter pin. Cust has on file now the model based on what Viking told him via received pictures of unit. Suggested to try to find replacement mini spade connector that would fit burner base and replace connector. Within 30 SC so NC."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT138FFDW01
Near Colorado Springs, CO 80921
Kris
Job Details: 01/13/2023
installed compressor charged system. ran test op unit is wotrking to spec. cx will monitor unit for 24 hours.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHW4
Near Colorado Springs, CO 80918
Jeremy
Job Details: 01/13/2023
Called tech support and confirmed unit is normal operation F# 7735491335. Told CX about service charge
We serviced a
KITCHEN AID DISHWASHER
Model KDPM604KPS0
Near Colorado Springs, CO 80918
Jeremy
Job Details: 01/13/2023
Installed all new parts. Ran a test cycle. Double checked for leaks. Placed leak detection kit under unit. Explained the survey to CX. Double checked warranty status.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Albuquerque, NM 87120
Larry
Job Details: 01/13/2023
Installed door and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MVWB765FC3
Near Albuquerque, NM 87120
Larry
Job Details: 01/13/2023
Installed Lid and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WFW9150WW01
Near Belen, NM 87002
Larry
Job Details: 01/13/2023
CX complaint - Not turning on - Unit needs controls - CX doesn't want to bear the cost of repair - Collected $129.95 Auth-R9UJUT
We serviced a
JENN-AIR MICROWAVE
Model JMW2430DP01
Near Colorado Springs, CO 80921
Kris
Job Details: 01/13/2023
ran test op could not get microwave to function. unit was not programmed correctly. reprogrammed correct model number ran test op all ok. cx is aware of 5 star survey.
We serviced a
MIDEA FREEZER
Model MRU17F6AWW
Near Colorado Springs, CO 80906
Ralph
Job Details: 01/13/2023
replaced listed part and cust to monitor the unit
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FPRU19F8RFF
Near Colorado Springs, CO 80906
Ralph
Job Details: 01/13/2023
this sensor is badf as well ordering another and will install once we get it. cust payiong ...cust paid in full autho no. c3k4y4
We serviced a
JENN-AIR MICROWAVE
Model JMC2430DS01
Near Colorado Springs, CO 80921
Kris
Job Details: 01/13/2023
installed console. ran test op with cx unit is working to spec.
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC503ESS01
Near Colorado Springs, CO 80918
Kris
Job Details: 01/13/2023
just want it noted cx stated when she turned off unit to defrost. freezer section was defrosting ice bin was not frozen and sausage was no longer frozen. installed ui set for 8 hiour defrost. all ok cx will monitor unit for 24 hours.
We serviced a
GENERAL ELECTRIC REFRIGERATOR/TOP
Model CYE22TP2MGS1
Near Pueblo, CO 81008
James K
Job Details: 01/13/2023
Installed previous techs ordered parts all ops test good
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JVM3160DF8BB
Near Colorado Springs, CO 80915
Jim
Job Details: 01/13/2023
replaced the 160 thermostat and the 110 thermostat unit test ok
We serviced a
MAYTAG DRYER
Model MED6230HW1
Near Rio Rancho, NM 87144
Joseph
Job Details: 01/13/2023
installed parts listed.un it tested good. unit is good to go.
We serviced a
KITCHENAID VENT HOODS
Model KVUB400GSS0
Near Colorado Springs, CO 80906
Ralph
Job Details: 01/13/2023
"installed part and unit checked okay, told cust avbout the survey"
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031US/AA
Near Colorado Springs, CO 80908
Brandon
Job Details: 01/13/2023
"Ran service mode test all ok, everything working as it should no issues found, recommended cx open door after cycle to help with drying. Tech line had me check temp of water after running unit for 15 minutes all ok hass not compatible cx not available to discuss survey"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Colorado Springs, CO 80917
Kris
Job Details: 01/12/2023
ran test op. unit is getting power. pulled door ui was unplugged from contriol. reseated connections ran test op all ok unit is working to spec. did not talk with cx about 5 star survey. unit was at a business.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Pueblo, CO 81003
Jeremy
Job Details: 01/12/2023
"Installed new gearcase and feet. Tested unit. Everything up to munufacturer specs.; (created new UIS, deleted prior attachment to UisID 194146)"
We serviced a
GENERAL ELECTRIC RANGE
Model JGS760EP3ES
Near Grand Lake, CO 80447
Erik
Job Details: 01/12/2023
installed orifice holder and convert to LP -test - good
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Colorado Springs, CO 80911
Jim
Job Details: 01/12/2023
"found the timer not advancing, replaced the timer unit test ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Colorado Springs, CO 80924
Aaron
Job Details: 01/12/2023
"No power coming from the board to drain pump or water inlet valve. Needs board. Board acu w11462458 $262.78Tax $21.55Hc $129.95Labor $169.95Total job $584.2330 day estimateNot home to advise of 5 star surveyCc on file not charged 129.95 as of yet, cx not home for approval"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Peyton, CO 80831
Kris
Job Details: 01/12/2023
installed ice maker. ran test op all ok unit is working to spec. freezer temp@2.5 ref temp@41.9
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ00
Near Colorado Springs, CO 80920
Kris
Job Details: 01/12/2023
found bad led. installed all ok cx is aware of 5 star survey.
We serviced a
GENERAL ELECTRIC DISHWASHER
Model PDT715SBNTS
Near Green Mountain Falls, CO 80819
Ralph
Job Details: 01/12/2023
"found a loose screw on the upper part of the tub that had loosined, tightened itg and unit chekced okay"
We serviced a
VIKING DISHWASHER
Model UE9
Near Woodland Park, CO 80863
Ralph
Job Details: 01/12/2023
"looks like unit had reg dish soap in the unit, added oil and it desolved the soap, cust to monitor"
We serviced a
WHIRLPOOL WASHER
Model MVWB765FW3
Near Peralta, NM 87042
Larry
Job Details: 01/12/2023
Unit needs drain pump - CX doesn not want to bear the cost of repair - Collected $129.95 - Auth-4U9R9H
We serviced a
SAMSUNG RANGE - GAS
Model NX58F5700WS/AA
Near Colorado Springs, CO 80926
Brandon
Job Details: 01/12/2023
Replaced ignitor and tested op all okCollected labor $169.95 check Auth# 3H44A9
We serviced a
MAYTAG DRYER
Model MEDC215EW1
Near New Castle, CO 81647
James R
Job Details: 01/12/2023
replaced heat element and cutout. Heat element was bad. checked vent it was pinched not much air flow. corrected. and connected vent. airflow is better. cycling on and off for heat on all cycles. op's of unit is good. repair complete.Suggested to customer to have venting of home cleaned. Please fill out whirlpool customer satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, NM 87113
Larry
Job Details: 01/12/2023
CX complaint - Makes loud grinding - Inspected unit and found the shifter was misaligned -mAdjusted shifter and tested good - Unit is good to go
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS0
Near Colorado Springs, CO 80908
Aaron
Job Details: 01/12/2023
"Circulation motor vibrating on back bracket, corrected motor and grommet, tested unit and working well, no leaks.Advised of survey"
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS04
Near Rio Rancho, NM 87144
Joseph
Job Details: 01/12/2023
installed parts listed. unit tested good. unit is good to go.
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Albuquerque, NM 87109
Larry
Job Details: 01/12/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS04
Near Rio Rancho, NM 87144
Joseph
Job Details: 01/12/2023
installed parts listed. unit tested good. unit is good to go.
We serviced a
GENERAL ELECTRIC RANGE
Model JS645SL6SS
Near Granby, CO 80446
Erik
Job Details: 01/12/2023
remove door - replace inner glass
We serviced a
GENERAL ELECTRIC DRYER
Model GTD33GASK1WW
Near Fraser, CO 80442
Erik
Job Details: 01/12/2023
check vent - clearckeck gas connection -ok cable jumper disconnected at switch - re-connect and test - good
We serviced a
GENERAL ELECTRIC DISHWASHER - BUI
Model GDT550PYR3FS
Near Winter Park, CO 80482
Erik
Job Details: 01/12/2023
"connect to SmartHQ diagnosticALERT: failure to drain on at least 1 of the last 5 cycles - check F56 error code diagnostic actionsF56 failure to drain - physically check unit for drain kinks/sump check valve obstructions - none present - replace pumpclear f codes, install pump and test - good"
We serviced a
MAYTAG WASHER
Model MHW6630HW0
Near Santa Fe, NM 87507
Jason
Job Details: 01/12/2023
checked unit found control is not supplyong voltage to motor and snutting down SC$140.02LABOR$160.55MISC$17.50CONTROL#W11322883$287.69TX$23.59TOTAL$629.35Auth code:LECH94$140.02
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EHL03
Near Aspen, CO 81611
James R
Job Details: 01/12/2023
Seal that was on door inside outer lip came loose. replaced R.H. fresh food door seal. customer had opened box and layed out flat. seal fit really well. checked for sealing all the way around. Looks good. when try to open door can feel that the magnet is holding well. please fill out customer satisfaction survey. Thank You.
We serviced a
MAYTAG DRYER - ELECTRIC
Model MEDB855DC4
Near Colorado Springs, CO 80919
Jim
Job Details: 01/12/2023
found the unit would not heat in the normal setting replaced the control board unit test ok T A S
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Calhan, CO 80808
Glenn
Job Details: 01/12/2023
"Install New Sump & Motor Assy, All OPS Test:OK, No Leaks, Installed Leak detector for safety."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Santa Fe, NM 87507
Jason
Job Details: 01/12/2023
installed part unit checks ok
We serviced a
SAMSUNG DRYER
Model DV42H5600EP/A3
Near Pueblo, CO 81005
Jonny
Job Details: 01/12/2023
"Noticed belt was off, put it back on, not hass com4, custy is nappy"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS01
Near Santa Fe, NM 87506
Jason
Job Details: 01/12/2023
installed gasket unit checks ok
We serviced a
FISHER & PAYKEL DISH DRAWER
Model DD24DV2T9 N
Near Woodland Park, CO 80863
Ralph
Job Details: 01/12/2023
"installed new rotor, still a little loud but the clicking noise has stopped, unit checked okay"
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Albuquerque, NM 87110
Larry
Job Details: 01/12/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Rio Rancho, NM 87124
Joseph
Job Details: 01/12/2023
smell coming from dishwasher. customer only uses machine 3 times a month. leaves old water at the bottom of the filter. found debree inside filter. cleaned filter. machine is working as designed. unit tested good. unit is good to go.
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC5
Near Los Alamos, NM 87544
Jason
Job Details: 01/12/2023
checked unit found unit was out of level causing unit to vibrate leveled unit. operation checks okAuth code:A94CM4 /for $129.25
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Albuquerque, NM 87105
Larry
Job Details: 01/12/2023
Found the evap therm not in correct place - Defrosted evap and secured therm - Unit should be good to go
We serviced a
SAMSUNG ELECTRON REFRIGERATOR
Model RF28R7201SG/AA
Near Woodland Park, CO 80863
Ralph
Job Details: 01/12/2023
installed part and unit checked okay
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Los Lunas, NM 87031
Larry
Job Details: 01/12/2023
Installed UI and tested good - Unit is good to go
We serviced a
SAMSUNG WASHER TOP LOAD
Model WA52A5500AC/US
Near Colorado Springs, CO 80925
Brandon
Job Details: 01/12/2023
Replaced pcb and tested op all ok hass passed and sent asked cx to complete survey
We serviced a
WHIRLPOOL MICROWAVE
Model KMHC319EBS3
Near Pueblo, CO 81001
James K
Job Details: 01/12/2023
"Found door separating from frame causing short in ui. Needs door W11205125 501.61+tax, sc 89.95, labor 139.95, mps 14.50. Total : 787.14 cust declines at this time"
We serviced a
SUBZERO REFRIGERATOR
Model IC-24R
Near Colorado Springs, CO 80921
Jessie
Job Details: 01/12/2023
"Customer refrigerator door sticks out slightly. See quick pics. Customer says unit doesn't have suction like the freezer does. I explained why freezer has more.Had to call techline, for any recommendations for the door slightly sticking out. And there are none as of now. No adjustment #$149.95 CK Auth# MTM994"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KBFN402ESS01
Near Snowmass Village, CO 81615
James R
Job Details: 01/12/2023
put into service diagnostics. #10 shifted into home position evac system. replaced F.F. evaporator Install sealer on small line of evaporator.Replaced drier. Installed valves. evac again. vac is holding. recharge system. op's good. Labor to finish repair. $595.00 office will take care of payment. file# 7735482706
We serviced a
JENNAIR OVEN
Model JDRP430WP01
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 01/12/2023
"Installed replacement UI board, collected remainder per note. Unit check ok. Returning both cores in as of 1-13-23. $205.17 CC Auth# X9H9WM"
We serviced a
JENN-AIR WALLOVEN
Model JMW2430LL00
Near Colorado Springs, CO 80906
Ken
Job Details: 01/12/2023
Installed console and tested. Advised customer to call back if they have anymore issues
We serviced a
GE DRYER
Model GTD65EBSJ3WS
Near Colorado Springs, CO 80903
Ken
Job Details: 01/12/2023
Tightened up the screw on the back of the drum and tested sc+100 for labor 229.95 auth a4ju9e
We serviced a
GE COOKTOP
Model JP930K0C1CC
Near Elbert, CO 80106
Glenn
Job Details: 01/12/2023
"RF Burner not working, also LF Burner not working properly. Parts No Longer Available.Paid for both tickets on this job.129.95 1st appliance + 89.95 2nd Appliance = $219.90Tried to use customers cell phone, but it was unclear for them to procees app. Bypassed Sign on App, had sign on ticket. Autho#WYTHN9719-339-8854"
We serviced a
BIG CHILL REFRIGERATOR
Model G91629NW
Near Colorado Springs, CO 80908
Jessie
Job Details: 01/12/2023
Replaced icemaker sent to customer. Test op. All on
We serviced a
WHIRLPOOL RANGE
Model KSEG700EBS2
Near Pueblo, CO 81001
James K
Job Details: 01/12/2023
"Found unit with f2e1 code indicating TouchPad issue, needs control assem W11091880 491 71+tax, sc 129.95, labor 169.95, mps 14.50. total: 846.43 cust declines at this time"
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Pueblo, CO 81004
James K
Job Details: 01/12/2023
"Found strike damaged causing unit to not advance cycle. Could not test drain pump but based on customers description most likely will need a drain pump as well. Need strike W11457841 +tax, sc 129.95, labor 149.95, mps 14.50. Total (pre pump) 331.17. If pump W11399437 is needed additional 183.52+tax. Cust declines at this time collected 129.95"
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS0
Near Pueblo West, CO 81007
James K
Job Details: 01/12/2023
Found element open causing no heat. Replaced with pre-ordered parts. All ops test good.