We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87112
Jason
Job Details:
03/23/2026
Installed valve ran quick cycle unit operation checks ok. spoke to cx about review
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS01
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/23/2026
"Turntable ring and coupler are squeaking during use, removed and replaced, tested unit, working and heating well now, verified by customer. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/23/2026
Arrived and removed failed control. Installed new control. Recalibrate unit. Tested washer on quick cycle. Unit is functioning now as designed. No further issues noted.
We serviced a
KENMORE WASHER
Model 11026902690
Near Colorado Springs, Colorado 80907
Earl
Job Details:
03/23/2026
Install the new drain pump.We couldn't test it because it's on a concrete floor some of the water came out onto the floor b impossible to figure out whether or not it was leaking at this point
We serviced a
GE REFRIGERATOR/TOP
Model GSE25GYPHCFS
Near Colorado Springs, Colorado 80911
Earl
Job Details:
03/23/2026
I installed the freezer door on the side by side.That was waiting for me unit is operating properly at this time
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS01
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
03/23/2026
"Removed and replaced components, tightened common wire at the junction box, tested unit, working and heating well now, verified by customer. Advised customer of 5 star survey. Case number 22964888"
We serviced a
THERMADOR DISHWASHER
Model DWHD770CFM/22
Near Avon, Colorado 81620
Erik
Job Details:
03/23/2026
FD 0305 00084INSTALL/ TEST: PASSJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87109
Jason
Job Details:
03/23/2026
Installed control. ran calibration cycle and quick wash cycle unit operation checks ok. spoke to cx about review
We serviced a
MONOGRAM REFRIGERATOR
Model ZISB420DHB
Near Colorado Springs, Colorado 80921
Charles
Job Details:
03/23/2026
Replaced upper led light switch
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS1
Near Albuquerque, New Mexico 87106
Jason
Job Details:
03/23/2026
Checked unit found wash motor not starting. pump motor assy needs replaced SC$149.95MPS$17.50LABOR$239.95PUMP MOTOR ASSY#W11416362$352.67TX$64.61TOTAL$824.68Auth code: F9JC4T$162.70
We serviced a
GE REFRIGERATOR
Model GFE28GSKMSS
Near Colorado Springs, Colorado 80911
Earl
Job Details:
03/23/2026
"Customers, complaint units is not making ice. I got ahold of g. E, and they ran me through diagnostics. Their suggestion is a frozen water line. The customer had already let it sit for 72 hours without running it, and it is in the refrigerator door and it still did not fill up with water, we're getting water to the solenoid cluster, but not past it. I quoted the price for new door the customer declined and paid the service fee authorization codeAJLXT3"
We serviced a
WHIRLPOOL RANGE
Model WFES3330RZ0
Near Grants Pass, Oregon 97527
Chris
Job Details:
03/23/2026
Replaced both hinges and tested. The condition has improved but I think it's normal.
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/23/2026
"Control is intermittently working, removed and replaced, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW500CMW0
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
03/23/2026
"Arrived and cx complaint of not finishing cycle. Cx had loaded towels. Started cycle then switched it you normal. She said it ran through but then wouldn't stop at end of cycle. She hadn't used it again. I arrived and ran rinse spin, and a quick wash. Both finished and seemed to run fine. Can't duplicate issue She had. Asked her to run a few more loads and let us know."
We serviced a
KITCHENAID WALL OVEN
Model KOED530PPS01
Near Colorado Springs, Colorado 80921
Jason
Job Details:
03/23/2026
"Installed new receiver and screws, test of the door and made sure that there were no issues how the customer test as well, unit repaired."
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Colorado Springs, Colorado 80920
Charles
Job Details:
03/23/2026
Will not power up until unplugged and then plugged back in. Replaced main control board
We serviced a
LG DRYER
Model DLE3600V
Near Pueblo, Colorado 81005
James
Job Details:
03/23/2026
Found loose wire at cntl causing intermittent heating secured and tested. All ops test good. Advised cust to have licensed dryer vent cleaner out to address slight vent restriction
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near La Pine, Oregon 97739
Levi
Job Details:
03/23/2026
Replace control board and also a flipped around the inlet hoses so that way the water temperature would match the proper valve. Test it and all checks okay perform to recalibration cycle.
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near La Pine, Oregon 97739
Levi
Job Details:
03/23/2026
Replace door boot seal and door locker assembly. Tested and no leaks at time of service and unit it seems to be working just fine. During testing I didn't notice I had an error code for something and I witnessed some suds in the machine so advice customer to use less soap. Drain pump seems to be operating just fine
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo, Colorado 81004
Domingo
Job Details:
03/23/2026
Replaced control board ran calibration; test it machine and machine is good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS322FDAM04
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/23/2026
"Removed and replaced modules, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
03/23/2026
Arrived and removed failed parts. Installed new parts. Tested washer on quick cycle. Unit is functioning now as designed.
We serviced a
GE W/D STACKED UNIT
Model GUD27ESSMWW
Near Grand Junction, Colorado 81501
Sean
Job Details:
03/23/2026
Verified the unit information customer signed disclaimer.Checked the unit for error codes.Found OBB and water supply .Checked the water and found the hot water was off. I turned it on and checked for leaks.Removed the front panel and ran a spin test found that the inner-drum was loose from the outer drum and was wobbly.Removed the auger and tightened the drum nut.Reassembled the unit and leveled it.Tested the unit it completed all the tests and no longer shaking.Tested the unit good.Please go online to D-3 A-OK Appliance service inc.And complete a technician survey.Your technician.Sean...
We serviced a
LG WASHER
Model WM1814CW
Near Colorado Springs, Colorado 80906
Mathew
Job Details:
03/23/2026
"Drain pump now making grinding noise, no debris found inside pump. Pump not shutting off. Recommend drain pump and water level sensor replacement at same time. Pump needs replaced. Part $110.34Tax $9.05MPs $14.50Labor $209.95$343.846601ER1006A $118.34Tax $9.70Complete repair total $471.88"
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Albuquerque, New Mexico 87105
Larry
Job Details:
03/23/2026
CX complaint - Not filling - Inspected unit and found dibris in the valve - Cleared dibris and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHB05
Near Seaside, Oregon 97138
Nathan
Job Details:
03/23/2026
Unit is working CX instruct about loading and temp settings were all the way cold
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Albuquerque, New Mexico 87105
Larry
Job Details:
03/23/2026
Arrived and the home in unsanitary conditions with the smell being unbearable and urine and feces all over the floor making it very sticky and unworkable
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Beaver Creek, Colorado 81620
Erik
Job Details:
03/23/2026
DRUM RUBBING ON RIGHT SIDE WALL SUPPORTMOUNT SCREW MISSING FROM MANUFACTURERREPLACE WITH PERSONAL HARDWARE AND TEST: PASSJOB COMPLETE
We serviced a
MIELE DISHWASHER
Model G7366
Near Vail, Colorado 81657
Erik
Job Details:
03/23/2026
CONNECT TO MDU - NO ERRORS LOGGEDAPPLY VARIANT PROGRAM (2ND ATTEMPT) - CALL MIELE TAG: CHECK PRESSURE SENSOR: GOODTEST INTAKE: GOODTEST DRAIN: GOODJOB COMPLETETEST ON NORMAL: PASSREF# 1011308236
We serviced a
MAYTAG REFRIGERATOR
Model MRT311FFFH01
Near Albuquerque, New Mexico 87105
Larry
Job Details:
03/23/2026
CX complaint - Still not cooling and getting condensation - Inspected unit and found a large gap between the liner and cabunet - Called techline (SR22970095) to document - Unit is unrepairable
We serviced a
WHIRLPOOL DRYER
Model WED5100HC4
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/23/2026
"Metal bracket vibrating against blower housing, corrected and tested unit, working and heating well now. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/23/2026
"Drive cam gears rattling, replaced and leveled unit, lower harness clip taghing against back panel, put drain hose in best place to help prevent tapping, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model PRSC2222AFA
Near Seaside, Oregon 97138
Nathan
Job Details:
03/23/2026
Seized and failed evap fan motor in freezer replaced Tested Advised of survey
We serviced a
MAYTAG WASHER
Model MVW7230HW2
Near Colorado Springs, Colorado 80917
Jason
Job Details:
03/23/2026
"Stator bolt were loose, causing the cover piece to move during agitation when it was going back and forth. Tighten it down and test it again, level unit for customer no more issues found, unit repaired"
We serviced a
SUBZERO REFRIGERATOR
Model CL485OSIDSP
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
03/23/2026
"FOUND ICE ON THE BACK WALL. ALSO ON THE DOOR FRAME AT THE TOP, SOMETHING WAS HOLDING DOOR OPEN AND ALLOWING CONDENSATION BUILD UP THAT WAS CASUING UNIT TO ICE UP, CLEARED ALL THE ICE AND UNIT CHECKED OKAY, CUST TO MONITOR"
We serviced a
MAYTAG WASHER
Model MTW7200RF0
Near Peyton, Colorado 80831
Aaron
Job Details:
03/23/2026
"F0E5 off balance error code in diagnostics, leveled unit and seated tub onto gearcase splines, put unit in best possible spot to help prevent tapping of drain hose. Advised customer of situation and survey."
We serviced a
GE WASHER
Model GTW220ACW0WW
Near Colorado Springs, Colorado 80920
Charles
Job Details:
03/23/2026
"Maintenance man said unit not occupied and unlocked. Replaced drain pump and speed sensor, ran drain and spin cycle."
We serviced a
WOLF RANGE
Model DF48450CG/S/P/LP
Near Arch Cape, Oregon 97102
Nathan
Job Details:
03/23/2026
Front SS panel on flip down panel had come loose from frame and was sitting crooked- causing weird opening of flip down controlsRemoved SS panel and re adhered to frameIt is just stuck with adhesiveIf it comes loose again- order flip down panel
We serviced a
SAMSUNG WASHER
Model WF50A8500AV/A5
Near Tillamook, Oregon 97141
Nathan
Job Details:
03/23/2026
Power to power board Nothing being out out Needs replaced Sc-$149.95Ship-$17.50Labor-$209.95Part#DC92-02837G-$341.74Total$719.14
We serviced a
GE RANGE
Model JBS86SP6SS
Near Fountain, Colorado 80817
Ralph
Job Details:
03/23/2026
"FOUND A CONNECTOR OFF THE ELEMEENT, REINSTALLED AND UNTI CHECKECKED OKAY"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23M8570SR/AA 03
Near Colorado Springs, Colorado 80923
Brandon
Job Details:
03/23/2026
"Error 22c, fridge fan working working, evap cover froze need evap cover assy, parts $335.92, labor $199.95, mps $14.50, tax $27.55, svf paid $149.95 CC Auth# CCJ3R3"
We serviced a
SAMSUNG DISHWASHER
Model DW80
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
03/23/2026
"Cx noticed high pitched noise at beginning of cycle indicating possibly something stuck in drain pump, ran unit thru functions all checks ok, no noise from unit told cx to use as normal and let us know if issue persists, svf paid $149.95 CC Auth# 9K993Y"
We serviced a
SUBZERO FREEZER
Model DEC2450FI/L
Near Colorado Springs, Colorado 80921
Charles
Job Details:
03/23/2026
"Condenser fan errors again, fan not running, removed piece of foam insulation that got sucked into fan"
We serviced a
GE WASHER
Model GFW650SPNSN
Near Pueblo, Colorado 81008
Domingo
Job Details:
03/23/2026
Replaced water valve and dispenser test machine in multiple cycles and it worked
We serviced a
MIELE COFFEE MACHINES
Model CVA6405
Near Colorado Springs, Colorado 80908
Charles
Job Details:
03/23/2026
"Ran clean milk pipe work cycle and degrease brew unit. Service fee $169.95, Labor 239.95, Total $409.90 paid autho Y34MER"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRtD1830AW0
Near Redmond, Oregon 97756
Richard
Job Details:
03/23/2026
"Install compressor filter, dryer recharge system all tested good at this time"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ10
Near Grand Junction, Colorado 81505
James R
Job Details:
03/20/2026
Signed disclaimer. Replaced dampner control. Test cycled sound normal. Is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS03
Near Grand Junction, Colorado 81503
James R
Job Details:
03/20/2026
Signed disclaimer. Checked in service test. Test 4 when first started hear a growl in the compressor area. Removed cover plate. Checked compressore amperage is .54 good. Cpondenser fan is running as should and is mounted properly.Could move the lines of high side to condenser it would make a vibration or a growl noise. Adjusted some of the lines which appeared to be touching base of the unit case. Checked other lines to make sure were not touching each other. Ok. Shut down and restarted several times and it didnt make the noise. Reinstalled compressor cover plate put back in place. Raised up on the front of unit some so it doesn't roll. Then started unit again and the noise did not repeat. Issue appears to be taken care of. Please fill out tech satisfaction survey. Thank You.
We serviced a
KENMORE REFRIGERATOR
Model 363. 9601715
Near Colorado Springs, Colorado 80915
Charles
Job Details:
03/20/2026
"Fridge 35 set at 3, freezer 15, Excessive run time, freeer over loaded and blocking airflow. Still working, old R12 system and no parts available. Service fee $149.95 paid check #360 autho WU499T"
We serviced a
DACOR STOVE
Model RGC365S/LP/H
Near Manitou Springs, Colorado 80829
Charles
Job Details:
03/20/2026
"Front right burner flames out on bottom of left side, took apart and cleaned. Did not fix, parts no longer available. Service fee $169.95 paid check #8605 autho NHC49J"
We serviced a
MAYTAG WASHER
Model MHW5630HC1
Near Colorado Springs, Colorado 80903
David
Job Details:
03/20/2026
"Unstacked unit, acu not providing voltage to motor. Needs control, cx opting to get new washer."
We serviced a
GE WASHER
Model GFW550SSN4WW
Near Colorado Springs, Colorado 80903
David
Job Details:
03/20/2026
"Installed control board, ran diagnostics, door is locking and unlocking like it should."
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Colorado Springs, Colorado 80925
Earl
Job Details:
03/20/2026
I can not duplicate issue
We serviced a
GE DISHWASHER
Model GDT670SYV3FS
Near Silverthorne, Colorado 80498
Erik
Job Details:
03/20/2026
INSTALL HEATER AND ADATER WITH NEW WASH ARM ASM/ TEST :PASSJOB COMPLETE
We serviced a
KITCHENAID M/W OTR
Model KMHS120ESS11
Near Sisters, Oregon 97759
Richard
Job Details:
03/20/2026
Tested unit replace lightbulb cycle tested unit all checks. Good at this time. Jobs complete
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Estancia, New Mexico 87016
Jason
Job Details:
03/20/2026
Installed control found unit not draining sediment had clogged drain line coming off pump. removed debries ran quick wash cycle unit operation checks ok. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Belen, New Mexico 87002
Larry
Job Details:
03/20/2026
Installed suspension and tested good - Unit is good to go - Survey mentioned
We serviced a
MAYTAG WASHER
Model MVW6230HW0
Near Los Lunas, New Mexico 87031
Larry
Job Details:
03/20/2026
Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
MAYTAG REFRIGERATOR
Model MFI2570FEZ12
Near Albuquerque, New Mexico 87104
Larry
Job Details:
03/20/2026
Installed UI and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL OTR MICROWAVE
Model WMH31017HS10
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/20/2026
"Control is intermittently holding power to the blower, removed and replaced control, tested unit, working and heating well now. It is possible for the blower to turn on for longer cooks to help cool the unit. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Monument, Colorado 80132
Earl
Job Details:
03/20/2026
I installed the new damper in tested unit is operating properly at this time
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
03/20/2026
Installed control board runs ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRSC5536RZ00
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
03/20/2026
Installed damper and motor runs all ok
We serviced a
LG REFRIGERATOR
Model LF25H6330S.ASTCNA0
Near Frisco, Colorado 80443
Antonio
Job Details:
03/20/2026
Installed new icemaker then cycled unit on for proper operation and unit is working properly
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
03/20/2026
Installed control board ran tests and calibration all ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF536RPS00
Near Palisade, Colorado 81526
James R
Job Details:
03/20/2026
"Signed disclaimer Replaced icemaker, Supply line from wtr valve to line that goes to the icemaker and then the evap cover. Dispensed wtr no leaks. Put a leak board under unit and took a pic. Please fill out tech satisfaction survey. Thank You."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
03/20/2026
Installed control board ran tests and calibration all ok
We serviced a
LG DRYER
Model DLEX6500B.ABLEEUS
Near Frisco, Colorado 80443
Antonio
Job Details:
03/20/2026
Installed new cntrl and ui panel then cycled unit on for proper operation and unit is testing good
We serviced a
GE RANGE
Model CTD90FP4N4W2
Near Breckenridge, Colorado 80424
Erik
Job Details:
03/20/2026
arc fault breaker triptest: air fry - no trip/ replace breaker if tripping continues
We serviced a
WOLF MICROWAVE
Model MD24TE/S
Near Colorado Springs, Colorado 80906
Charles
Job Details:
03/20/2026
Replaced user interface
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Battlement Mesa, Colorado 81635
James R
Job Details:
03/20/2026
sp w11766193 special project s153eb Checked pressure tube is clear. Checked at the tub re-positioned so wasnt such a sharp bend. Calibrated control and then ran thru a service test is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/20/2026
"Control is sending constant power to the drain pump, removed and replaced control, recalibrated and tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/20/2026
"Control is shorted out, removed and replaced control, proper power is need to the unit for unit to heat, not enough power between red and white wires on the terminal block, recommend electrician. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/20/2026
"Capacitor is shorted out, shorted control, removed and replaced components, recalibrated and tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/20/2026
"Oven door pulling upwards, removed and replaced door hinge assembly, tested unit, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW
Near Fountain, Colorado 80817
Carlos
Job Details:
03/20/2026
Installed control board ran tests and calibration all ok
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/20/2026
"Oven door hinge is pulling door upwards, removed and replaced hinge assembly, tested unit, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
03/20/2026
Installed control board ran tests and calibration all ok
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Cimarron Hills, Colorado 80915
Carlos
Job Details:
03/20/2026
Installed control board ran tests
We serviced a
GE WASHER
Model GTW335ASN2WW
Near Grand Junction, Colorado 81501
Sean
Job Details:
03/20/2026
Verified information customer signed disclaimerRemoved the auger and connecting bolts Leaned the unit back and unhooked the motor and shifter Removed them and removed the gear case.Installed the new gear case and cleaned out the drum and auger. Reassembled the unit with the new parts and tested the unit.The unit is operating as designed by factory.Do not over fill the fabric softener. It will turn into black sludge in the bottom of the drum.
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/20/2026
"Oven door hinge is pulling door upwards, removed and replaced hinge assembly, tested unit, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Albuquerque, New Mexico 87111
Jason
Job Details:
03/20/2026
Installed control and encoder ran quick cycle unit operation checks ok. spoke to cx about review
We serviced a
JENN-AIR WALL OVEN
Model JJW2830LM01
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
03/20/2026
Arrived and cx complaint of oven not chiming or ringing when reaches temp in convection roast. Techline or whirlpool couldn't answer. Replaced ui/manager. Tested unit on convection roast. Reached temp. Did not alert in any way its at temp. Engineering issue? Cx is ok with it. Just wanted to verify this us how it works. Informed cx of review process.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/20/2026
Arrived and removed old parts. Installed new parts. Cleaned out vent jose.had lint build up. Ran dryer. It temped out at 155. Unit is functioning now as designed
We serviced a
WHIRLPOOL DRYER
Model WGD4307SW0
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/20/2026
Arrived and cx complaint of check lint light on. The newer dryers tend to have that light on even when lint screen is clean. Temped dyer. Its at 155. Dryer is functioning as designed. Possible vent issue on roof or because it vent up to the roof. Informed cx of review process.
We serviced a
MIELE DRYER
Model TXR860WP
Near Breckenridge, Colorado 80424
Erik
Job Details:
03/20/2026
update variant programpersistant f66 - 10k ftjob comlpete
We serviced a
JENN-AIR RANGE
Model JES1750ML1
Near Sunriver, Oregon 97707
Levi
Job Details:
03/20/2026
Replace glass cooktop tested and all checks okay.
We serviced a
WHIRLPOOL RANGE
Model WGE745C0FS
Near Grand Junction, Colorado 81504
Sean
Job Details:
03/20/2026
Pulled the unit out and replaced the temp probes for top and bottom ovens. Celebrated the ovens to be within 15? of set point.Tested the units good.Thank you.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Grand Junction, Colorado 81501
Clint
Job Details:
03/20/2026
Customer signed disclaimer and recieved parts ordered.Installed new control and pump. Calibrated new control and ran on normal cycle.Checked spin cycle and for leaks . Everything checkedbout perfectly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Albuquerque, New Mexico 87111
Jason
Job Details:
03/20/2026
Installed control. ran calibration cycle and quick wash. unit operation checks ok. spoke to cx about review
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Albuquerque, New Mexico 87110
Jason
Job Details:
03/20/2026
Checked unit found freezer led module had failed installed module and tighened handles for cx. unit operation checks ok. spoke to cx about review
We serviced a
GE RANGE
Model GRS60LAV1FS
Near Grand Junction, Colorado 81504
Clint
Job Details:
03/20/2026
Customer signed disclaimer and recieved parts ordered. Installed parts put through test cycle and unit ran perfectly. PLEASE TAKE TECH SURVEY THANKS.CLINT.
We serviced a
LG REFRIGERATOR
Model LRMDS3006S
Near Sisters, Oregon 97759
Richard
Job Details:
03/20/2026
Installed new Baller icemaker cycled tested all checks. Good at this time.
We serviced a
LG REFRIGERATOR
Model LRYXC2606SS/00
Near Sisters, Oregon 97759
Richard
Job Details:
03/20/2026
Installed new baller ice cycled all tested fine at this time
We serviced a
MAYTAG DRYER
Model MED6200KW1
Near Bend, Oregon 97701
Richard
Job Details:
03/20/2026
"Installed new rollers, belt and idler pulley Cycle tested unit all tested fine at this time"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87123
Jason
Job Details:
03/20/2026
Installed control ran calibration cycle and quick wash cycle. unit operation checks ok. spoke to cx about review
We serviced a
SAMSUNG WASHER
Model WA54CG7150AD
Near Colorado Springs, Colorado 80923
Brandon
Job Details:
03/20/2026
Replaced motor and tested operation all checks ok
We serviced a
GE REFRIGERATOR
Model PFSS6PKXBSS
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
03/20/2026
"Unit not cooling at all, sealed sytem is empty. Customer not interested in any large repairs. RK149.95Auth 4EFW3M"
We serviced a
FRIGIDAIRE RANGE
Model GCFI3060BFE
Near Colorado Springs, Colorado 80923
Earl
Job Details:
03/20/2026
Install the generator boards and user interfaces.And we tested unit operating properly at this time
We serviced a
MIELE DRYER
Model MTWD360WP
Near Breckenridge, Colorado 80424
Erik
Job Details:
03/20/2026
oulet shorted/ no break at fuse boxtest on different outlet: PASScx needs electrician to complete repairsjob complete