We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
01/23/2026
"Installed control board , ran test and calibration runs all ok"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Cimarron Hills, Colorado 80915
Carlos
Job Details:
01/23/2026
Installed control board ran tests and calibration runs all ok
We serviced a
MAYTAG WASHER
Model MVW6200KW3
Near Albuquerque, New Mexico 87106
Larry
Job Details:
01/23/2026
Installed suspension and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDF110PABB5
Near Albuquerque, New Mexico 87112
Jason
Job Details:
01/23/2026
Checked unit found element had failed. installed element ran diagnostic cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Albuquerque, New Mexico 87110
Jason
Job Details:
01/23/2026
Checked unit found door had come apart. re-assembled door unit opperation checks okAuth code: 9VU9AY$149.95
We serviced a
WHIRLPOOL WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
01/23/2026
Installed control board ran tests and calibration runs all ok.
We serviced a
WHIRLPOOL WASHER
Model MHW6630HW3
Near Albuquerque, New Mexico 87109
Jason
Job Details:
01/23/2026
Installed control panel. ran quick cycle. unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87109
Jason
Job Details:
01/23/2026
Installed control. ran calibration cycle and quick wash. unit opperation checks ok. spoke to cx about review
We serviced a
KITCHENAID DISHWASHER
Model KDFE104DWH5
Near Albuquerque, New Mexico 87109
Jason
Job Details:
01/23/2026
Checked unit found wash motor not starting. installed pump motor assy ran quick cycle. unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Albuquerque, New Mexico 87120
Larry
Job Details:
01/23/2026
CX complaint - he dishwasher is filling up with water after the wash cycle completes - Inspected unit and foundthe drain hose high loop fell causing water to back-syphon into the DW - CX corrected unit is operating as designed - Survey metioned - Collected SC-auth-NW49KJ
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW0
Near Albuquerque, New Mexico 87121
Larry
Job Details:
01/23/2026
"CX complaint - Washer not starting - Inspected unit and found F9E1, F1E2, F1E1 and F8E6 - Checked and not getting response from control and the harness failed at the drain pump - Unit needs control and harness to get it uo and running - CX doesn't want to bear the cost of repair - Collected SC-auth-X4K3JW"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
01/23/2026
Installed control board ran test and calibration runs all ok
We serviced a
WHIRLPOOL DRYER
Model WGD5620HW0
Near Peyton, Colorado 80831
Earl
Job Details:
01/23/2026
"Customer's complaint unit seems to be taking longer to dry. I arrived. It is a gas dryer, I put my temperature probe in the temperatures were accurate. They use dryer sheets and have for years. I explained to them that the waxy substance can run off onto the sensors, explain to them how to clean the sensor I gave the price of the sensor they declined. Unit is operating properly.At this time authorization code WXX339"
We serviced a
KITCHENAID WALL OVEN
Model KOED530PPS01
Near Colorado Springs, Colorado 80924
Earl
Job Details:
01/23/2026
I installed the new hinges and tested good customers happy unit is operating properly at this time
We serviced a
SAMSUNG WASHER
Model WD53DBA900HZA1
Near Monument, Colorado 80132
Brandon
Job Details:
01/23/2026
"Replaced diaphragm, and tested operation all checks ok hass passed"
We serviced a
WHIRLPOOL W/D STACKED UNIT
Model CGT9000GQ1
Near Ashland, Oregon 97520
Thomas
Job Details:
01/23/2026
Emptied water from washer. Found object hooked around the impeller. Removed object. Ran tested okay with customer present. No leaks
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
David
Job Details:
01/23/2026
"Drain pump continuously running, Replaced control, ran calibration and diagnostic cycles. All good"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
David
Job Details:
01/23/2026
"Replaced control, ran calibration and diagnostic cycles. All good"
We serviced a
SAMSUNG WASHER
Model WF45B6300AC/US
Near Monument, Colorado 80132
Brandon
Job Details:
01/23/2026
"Bearings in back tub worn and bad, replaced back tub, bolts and weights, tested operation all checks ok hass passed"
We serviced a
LG REFRIGERATOR
Model LF26C6230V.ANSCNA0
Near Colorado Springs, Colorado 80924
Charles
Job Details:
01/23/2026
Left door sitting low and flap not engaging. Raised left door adjuster and mullion flap working
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80917
Carlos
Job Details:
01/23/2026
Installed control board ran test and calibration all ok.
We serviced a
SAMSUNG WASHER
Model WF45T6000AW/A5
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
01/23/2026
"Error dc1, bad door switch, replaced door lock and tested operation all checks ok hass passed"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Colorado Springs, Colorado 80918
Ryan
Job Details:
01/23/2026
"Replaced both door hinges. All now checks ok, door is working properly. RK"
We serviced a
MAYTAG FREEZER
Model MZF34X16DW09
Near Colorado Springs, Colorado 80917
Ryan
Job Details:
01/23/2026
"Found unit off on thermostat. Changed control and thermistor. Unit is a little overloaded, advised customer. RK"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Colorado Springs, Colorado 80922
Ryan
Job Details:
01/23/2026
Replaced control board and ran automatic test cycle. Unit is now working properly. RK
We serviced a
WHIRLPOOL WASHER/DRYER COM
Model WET4027HW2
Near Grand Junction, Colorado 81505
Clint
Job Details:
01/23/2026
Property Manager signed disclaimer stated dryer was taking a long time to dry. After inspection I found the lint screen vent had a big piece of lint blocking it. Looks like client had not been cleaning off the screen.PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
GE WASHER/DRYER COM
Model GUD24ESSM1WW
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
01/23/2026
Replaced components and tested operation. Unit is working properly but is extremely oversudsing. Advised to cut soap use in half and run multiple cleaning cycles. RK
We serviced a
LG ELECTRIC RANGE
Model LREL6323D.FBDLLGA01
Near Colorado Springs, Colorado 80916
Mathew
Job Details:
01/23/2026
"Lg tech support told me that this unit was deemed unrepairable in November, will return parts as no repair is needed."
We serviced a
JENNAIR ICE MACHINE
Model JUIFX15HX02
Near Colorado Springs, Colorado 80921
Ryan
Job Details:
01/23/2026
"Replaced harness, re-schedule to return unit to customer. RK"
We serviced a
WHIRLPOOL WASHER
Model WET4027HW2
Near Grand Junction, Colorado 81505
Clint
Job Details:
01/23/2026
"Tenant signed disclaimer, unit wasnt heating and sent element ,thermostats to tech. Fuse on element was faulty and replaced thermal cutoff and element. Unit heated and ran perfectly."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814WW
Near Bend, Oregon 97702
Levi
Job Details:
01/23/2026
"Replace defrost timer, tested, all checks okay"
We serviced a
LG WASHER
Model WM2801HLA
Near Pueblo, Colorado 81001
James
Job Details:
01/23/2026
Installed ordered parts tested ops all ckok
We serviced a
MIDEA REFRIGERATOR
Model MRQ22D7AST
Near Colorado Springs, Colorado 80909
Charles
Job Details:
01/23/2026
Replaced freezer ice maker
We serviced a
GE WASHER/DRYER COM
Model PFQ97HSPVODS
Near Fruita, Colorado 81521
Sean
Job Details:
01/23/2026
Verified the unit information & customer signed disclaimer.Checked the unit and found the door gasket retainer spring was not on the unit .I checked the gasket for damage it doesn't appear to have any. Reattached the retainer spring. Tested the unit and watched for any leaking . The unit tested good .Operating as designed by factory.If you are satisfied with the service I have provided you with today then please share your experience with others by going online @ D-3 A-OK Appliance service inc.And fill out a technician survey.Thank you.Your technician...Sean.
We serviced a
MIELE DRYER
Model TXI680WP
Near Breckenridge, Colorado 80424
Erik
Job Details:
01/23/2026
INSTALL/ TEST: PASSCX CLAIMS NO CHANGE FILTER ERRORS SINCE FILTER CHANGEJOB COMPLETE
We serviced a
GE DISHWASHER
Model GDP665SYN8FS
Near Breckenridge, Colorado 80424
Erik
Job Details:
01/23/2026
CONNECT TO SMARTHQ SERVICE: ERROR DRAIN FAILUREFILL FAILUREPRESSURE LOSS DUE TO OBSTRUCTION IN PRESSURE SENSOR -CLEAN / REINSTALLTEST: PASSJOB COMPLETE
We serviced a
LG RANGE
Model LTEL7337F.BRSLLGA
Near Colorado Springs, Colorado 80925
Mathew
Job Details:
01/23/2026
Install LG provided kit for regulator/ harness/ control board. Test op on all burners and both ovens. All okay.
We serviced a
MAYTAG DRYER
Model MED6500MBK0
Near Colorado Springs, Colorado 80907
Charles
Job Details:
01/23/2026
"Long dry time, 2nd floor, vented to roof, ran with vent connected and unit overheating and short cycling, not drawing air at lint screen. Disconnected vent tube from dryer, unit heating and cycling normal, great air draw."
We serviced a
KITCHENAID BI FREEZER
Model KBSD708MPS00
Near Silverthorne, Colorado 80498
Rudy
Job Details:
01/23/2026
Installed a new water filter correctly. Filter is staying in its place no leaks. Ran six 16oz. Glasses of water through water dispenser. All is good. If problem reacures gonna need 2 techs. To replace housing.
We serviced a
GE WASHER
Model GFW655SSV0WW
Near Fruita, Colorado 81521
Sean
Job Details:
01/23/2026
Reset the unit tested good.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Clifton, Colorado 81520
James R
Job Details:
01/23/2026
Signed disdclaimer. Replaced block and installed shelf. Ok Please fill out tech satisfaction survey. Thank You.
We serviced a
GE DISHWASHER
Model GDP6705SYV1FS
Near Grand Junction, Colorado 81505
Sean
Job Details:
01/23/2026
Verified the unit information & customer signed disclaimer.Checked the unit and found the tub has a crack in the back right side.Called support and talked to Cory. Sent pictures and got case number # ( 20338274 )Customer relations will contact you within the next 3 to 4 business days.
We serviced a
KENMORE WASHER
Model 110.81950100
Near Colorado Springs, Colorado 80906
Charles
Job Details:
01/23/2026
Instruct custom must pull knob to start Service fee $149.95 paid check #8519 authoFN3MLY
We serviced a
THERMADOR RANGE
Model PRD486WDHU/06
Near Breckenridge, Colorado 80424
Erik
Job Details:
01/23/2026
FD 0308 00033TEMP OFFEST REQUIRED AT 9K FTCALL BSH TAG: CONFIRM UNIT WORKING AS DESIGNED WITH FAN AND PRE-HEAT/ FAST PRE-HEAT TESTINGSET OFFSET 20* - THEN TEST: PASSJOB COMPLETE
We serviced a
MIELE DRYER
Model TXR860WP
Near Dillon, Colorado 80435
Erik
Job Details:
01/23/2026
INSTALL/CONNECT TO MDU: ALL VARIANTS PROG UP TO DATETEST INDICATE NO GREATER THAN 20* GAP IN COOLANT TO SENSOR AT EXHAUSTNO F66 AFTER LIVE TEST NORMALJOB COMPLETE
We serviced a
BOSCH DISHWASHER
Model SHV78CM3N/25
Near Silverthorne, Colorado 80498
Erik
Job Details:
01/23/2026
INSTALL DRAIN PUMPJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
David
Job Details:
01/23/2026
"Drain pump continuously running, Replaced control, ran calibration and diagnostic cycles. All good"
We serviced a
KITCHENAID DISHWASHER
Model KDTE304RPS0
Near Tillamook, Oregon 97141
Nathan
Job Details:
01/23/2026
Replaced over heat Tstat and board due to heating element not coming onTestedAdvised of survey
We serviced a
GENERAL ELECTRIC WASHER-DRYER COM
Model GUD27ESSM1WW
Near Silverthorne, Colorado 80498
Erik
Job Details:
01/23/2026
ACCESS WITH DOOR CODEINSTALL/TEST: PASSJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
David
Job Details:
01/23/2026
"Drain pump continuously running, Replaced control, ran calibration and diagnostic cycles. All good"
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS2
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
01/23/2026
"Contacted Techline under Service Request SR-22316147 to verify electrical requirements and operating current of the unit. Performed an amp draw test with all burners energized and operating simultaneously to simulate maximum load conditions. During testing, the unit drew approximately 42.3 amps under full operation. Based on this measured load and the manufacturers specifications, the unit requires a dedicated 50-amp circuit breaker. This requirement is due to the unit being configured for 208 volts, three-phase power, which necessitates additional capacity to safely handle peak current demand and ensure proper operation without nuisance tripping or electrical overload. Techline stated according to requirement specs on this machine it will have an amp draw of 46 amps"
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HZ07
Near La Pine, Oregon 97739
Levi
Job Details:
01/23/2026
"Replaced all high voltage side parts, tested and the unit is heating and sounds good."
We serviced a
FRIGIDAIRE DISHWASHER
Model FDPH4316AW1A
Near La Pine, Oregon 97739
Levi
Job Details:
01/23/2026
"Replace control board and user interface board, tested and it tests good"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC
Near Pueblo, Colorado 81004
Domingo
Job Details:
01/23/2026
Called cx and said that it was supposed to be the dryer not the washer and she canceled bc the dryer is working fine now
We serviced a
SAMSUNG REFRIGERATOR
Model RS22T5201SR/AA
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
01/23/2026
"No errors, checked compressor and sensors. No issues found, recommend cx leave unit plugged in if issue occurs again, hass passed"
We serviced a
WHIRLPOOL WASHER
Model WFW4720RW0
Near Rifle, Colorado 81650
James R
Job Details:
01/23/2026
Printed labels took pics ready to send.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
David
Job Details:
01/23/2026
"Failed board, Replaced control, ran calibration and diagnostic cycles. All good"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Merlin, Oregon 97532
Chris
Job Details:
01/22/2026
"The cold water hose was kinked, keeping the water valve open to long. I straiten it out and tested. Working normally."
We serviced a
MAYTAG WASHER
Model MVW4005SW0
Near Trinidad, Colorado 81082
James
Job Details:
01/22/2026
Found pressure hose disconnected causing unit to have long fill code. Secured hose and tested ops ckok. Advised cust to have licensed plumber out to address clogged stand pipe
We serviced a
ZLINE COOKTOP
Model RTS-BR-36
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
01/22/2026
"Cleaned off burner and electrode on large burner and all burners are now working properly. Customer lost adjustment tool, Called Z-Line and they are sending out an adjustment tool and instructions on how to adjust volume at each burner. RK"
We serviced a
KITCHENAID RANGE
Model KFGG500ESS8
Near Eagle, Colorado 81631
Antonio
Job Details:
01/22/2026
Installed new srew under bull nose unit is secure
We serviced a
LG REFRIGERATOR
Model LRFVC2406D.ASBCNA0
Near Vail, Colorado 81657
Antonio
Job Details:
01/22/2026
Installed new evaporators then charged system with r600 unit is working properly
We serviced a
MIELE COFFEE MACHINE
Model CVA7845
Near Aspen, Colorado 81611
Sean
Job Details:
01/22/2026
Checked the unit verified the information.Customer signed disclaimer.Pulled the unit out and removed the panels. Removed the pump flowmeter and membrane and installed the new parts. Reassembled the unit. Hooked it back up and tested. The unit tested good.Operating as designed by factory.Thank you please fill out a technician survey.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo West, Colorado 81007
Domingo
Job Details:
01/22/2026
Replaced control calibrated machine and ran diagnostic and it passed
We serviced a
SAMSUNG DRYER
Model DVE45B6300C
Near Kiowa, Colorado 80117
Earl
Job Details:
01/22/2026
Customers complaint unit not heating bad heating element.I replaced it unit is operating properly at this time
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
01/22/2026
"Releveled dishwasher, was leaning forward, runs all ok"
We serviced a
LG DRYER
Model DLEX8900B
Near Winter Park, Colorado 80482
Rudy
Job Details:
01/22/2026
Customer paid $289.95 Auth #N4V949 though I wallet. Dryer was being set wrong. Showed CX how to set dryer. All is good.
We serviced a
LG REFRIGERATOR
Model LFXS26973S
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
01/22/2026
Replaced evap cover and tested operation all checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Tijeras, New Mexico 87059
Jason
Job Details:
01/22/2026
Installed control ran calibration cycle and quick wash. unit opperation checks ok. spoke to cx about review
We serviced a
THERMADOR WALL OVEN
Model ME302YP/02
Near Fraser, Colorado 80442
Erik
Job Details:
01/22/2026
INSTALL/ TEST: PASSJOB COMPLETE
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS 2
Near Grants Pass, Oregon 97526
Chris
Job Details:
01/22/2026
Replaced the wash pump and tested.
We serviced a
ELECTROLUX DRYER
Model ELFE7637AT1
Near Peyton, Colorado 80831
Earl
Job Details:
01/22/2026
"Uninstall , the motor in the belt and tested at unit is operating properly at this time"
We serviced a
LG DISHWASHER
Model LDFN4542S.ASSESNA
Near Fountain, Colorado 80817
Brandon
Job Details:
01/22/2026
Replaced hose and tested operation all checks ok leak strip installed stalled
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ13
Near Colorado Springs, Colorado 80904
Charles
Job Details:
01/22/2026
CORRECT ADDRESS: 7015 LOCO PONY CT. No response from any button. Replaced user interface touchpad. Tested all functions.
We serviced a
WHIRLPOOL WASHER
Model MHW5630HW3
Near Los Ranchos de Albuquerque, New Mexico 87107
Larry
Job Details:
01/22/2026
Installed parts lsited and tested good - Unit is good to go
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Depoe Bay, Oregon 97341
Nathan
Job Details:
01/22/2026
SWITCH TO CODOnly 120v supplied to unit Dryer not heating and leg that splits to washer was dead at plug
We serviced a
WHIRLPOOL WASHER
Model WFW5720RU0
Near Peyton, Colorado 80831
Earl
Job Details:
01/22/2026
"Customers, complaint unit rattling really loud.I arrived and had to explain to them. The unit needs to be loaded in a certain way. Because there's no codes recorded. I ran. The unit that's perfectly fine customers were happy with. The explanation unit is operating properly at this time."
We serviced a
KITCHENAID MICROWAVE
Model KMHS120KPS01
Near Rio Rancho, New Mexico 87124
Larry
Job Details:
01/22/2026
CX complaint - Light keeps going out - Inspected unit and found the lamp failed - Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRSF5536RZ00
Near Colorado Springs, Colorado 80920
David
Job Details:
01/22/2026
"Installed ordered parts, working as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Rio Rancho, New Mexico 87144
Larry
Job Details:
01/22/2026
CX complaint - Washer won't stop running unless you unplug it - Inspected unit and found F3E1 error - Replace contro and tested good - Unit is good to go - Survey mentioned - Advised CX that supply hoses are leaking and should be replaced
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Rio Rancho, New Mexico 87124
Larry
Job Details:
01/22/2026
CX complaint - Washer won't drain - Inspected unit and found the lower harness failed - Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL RANGE
Model WFES3330RS0
Near Colorado Springs, Colorado 80920
David
Job Details:
01/22/2026
Installed new door gasket.
We serviced a
THERMADOR RANGE
Model PRD486WDHU/12
Near Tabernash, Colorado 80478
Erik
Job Details:
01/22/2026
install bullnosejob complete
We serviced a
GE REFRIGERATOR
Model GSS25GYJCFS
Near Depoe Bay, Oregon 97341
Nathan
Job Details:
01/22/2026
Frozen water line in door causing bad dispenser function See notes Advised of survey
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS00
Near Colorado Springs, Colorado 80921
Ryan
Job Details:
01/22/2026
Replaced control board and ice box fan is now running. Allow 24 hours for ice production. RK
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87123
Jason
Job Details:
01/22/2026
installed control ran calibration unit checks ok
We serviced a
SAMSUNG DRYER
Model DVE50BG8300VA3
Near Colorado Springs, Colorado 80924
Mathew
Job Details:
01/22/2026
Found light fixture broken off in tub. Replace light and wire. Test op all okay.
We serviced a
JENNAIR MICROWAVE
Model JMW2430IL02
Near Colorado Springs, Colorado 80921
Charles
Job Details:
01/22/2026
"F2-E1 error, need console W11449292, Service fee $169.95, Labor $219.95, MPS $14.50, Part $886.27, Tax 72.67, Total $1363.04, declined estimate, paid service fee autho 9T449P"
We serviced a
SUB ZERO REFRIGERATOR
Model DEC3050RID/R
Near Colorado Springs, Colorado 80921
Charles
Job Details:
01/22/2026
"Fridge 58 degrees, error 40140 on display, frozen evaporator. 22 codes in memory. Cleared codes. Defrost and relocate thermostat per tech line. Service fee $209.95 paid autho WK4N3J"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHB11
Near Albuquerque, New Mexico 87123
Jason
Job Details:
01/22/2026
Checked unit found line goingto dispensor wasnt seated in quick connect. seated line re-checked unit. opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW500CMW1
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
01/22/2026
"Installed latch, strike and bezel all ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED2CHQXVQ00
Near Albuquerque, New Mexico 87110
Jason
Job Details:
01/22/2026
Checked unit found connector at condensor fan motor had come un-seated causing fan to kick in and out. re- seated connector unit opperation checks ok. spoke to cx about review
We serviced a
GE REFRIGERATOR/TOP
Model GNE27JYMXFFS
Near Granby, Colorado 80446
Erik
Job Details:
01/22/2026
connect to smarthq service: cycle history shows temps within range in both FF and FZ* see quick picsextensive history show consistant temps - inform cx unit is single compressor/ evap and borrows cold air from FZ and pushes it to FF cavity - anything placed in front of the vent will be exposed to FZ temps and is likely to freeze (intented design)case#19661522call GE TAG: in team meeting: must call back in 1 hour1-800-386-1215 CR
We serviced a
DACOR DOUBLE WALL OVEN
Model DTO230S
Near Monument, Colorado 80132
Mathew
Job Details:
01/22/2026
"Could not find model/serial tag. Set temp to 350. Monitored oven temps, my probe read 352. Put cold cast iron pan in oven. Oven regained set temp within 15 minutes. Inspect elements, elements ok. $179.95 CC Auth# FM3TT9; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)"
We serviced a
LG DISHWASHER
Model LDFN4542S.ASSESNA
Near Colorado Springs, Colorado 80908
Charles
Job Details:
01/22/2026
Replaced broken dispenser
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Colorado Springs, Colorado 80904
Brandon
Job Details:
01/22/2026
Replaced ice maker and cycled all checks ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS00
Near Monument, Colorado 80132
Ryan
Job Details:
01/22/2026
"Cleaned out clogged condenser coils , checked all electrical connections, and cycled power to unit. All now working properly. RK"
We serviced a
BEST DOWNDRAFT VENT
Model D49M48SB
Near Larkspur, Colorado 80118
Ryan
Job Details:
01/22/2026
Tightened screw on lid and made as many adjustments to poor install as possible. Unit is working fine now. Doesnt look like granite was cut square and lid was catching on countertop. RK
We serviced a
WHIRLPOOL WASHER
Model WTW4957PWO
Near Aspen, Colorado 81611
Clint
Job Details:
01/22/2026
Customer signed disclaimer and recieved control board.installed control and ran unit no leaks were detected and functioning properly. Taking control for core return. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC136RPS00
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
01/22/2026
Installed HV board and control board cx will observe

