We serviced a
MAYTAG RANGE
Model WFG320M0BS3
Near Pueblo, CO 81001
David
Job Details: 01/05/2024
Checked range Called safety teamThey said outer door glass not under warranty RA #7738143016Gave cx prices for repair They are opting to buy new range
We serviced a
SUBZERO WINE COOLER
Model IW-30RA
Near Colorado Springs, CO 80906
Roman
Job Details: 01/05/2024
"Display is not displaying correctly, called tech support and they had me unplug connectors at the control board and plug back in, display kicked back on and started working. Paid Sc"
We serviced a
GE REFRIGERATOR
Model GSS25JETH
Near Colorado Springs, CO 80910
Roman
Job Details: 01/05/2024
Drain hole below the Evaporator is clogged. Removed the drain line and cleared it. Defrosted the ice and cleaned the coils. Made sure fans and compressor is running. Defrost Heater #WR51X10055 $155.26Labor $149.95Sc $129.96Total cost $279.95 $279.95 CC Auth# TWLP39Would like a mailed receipt
We serviced a
MAYTAG WASHER
Model MHN30PDBWW0
Near Colorado Springs, CO 80915
Roman
Job Details: 01/05/2024
"Washer showing error code F20, fill issue, checked the water lines and they are freezing up. Recommend a having a small heater in that room or insulating the hoses. Washer drain pump and inert valve can crack with the cold. *CX open service door and hold down quick cycle till all lights flash, put the service door back on and it should and the washer should go back to the price if issue happens again.Paid sc"
We serviced a
WHIRLPOOL WASHER
Model MHW6630HW3
Near Grand Junction, CO 81503
James R
Job Details: 01/05/2024
F5E2 door unlock failure. Door did lock cleared code. ac good and is correctcpwr grd and neutral. Checked outlet has 121 vac. Put into diagnostics. Turned but never spun. Unplugged to reset control and test again. Unit went thru as it should. Called tech line. SR# 773817656signed disclaimers. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SAMSUNG WASHER
Model WA50R5200A
Near Colorado Springs, CO 80917
Kris
Job Details: 01/05/2024
unit was not level when arrived leveled unit ran test op with 6 large towels on quick wash.
We serviced a
GE REFRIGERATOR/TOP
Model GTS22KYNBRFS
Near Silverthorne, CO 80498
Erik
Job Details: 01/05/2024
install part and test: DEFROST -OKSENSOR POSITION -OKJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW2
Near Colorado Springs, CO 80924
Aaron
Job Details: 01/05/2024
"F7E1 motor errorF7E6 motor circuit error codes upon arrival, capacitor is shorted out, approved onsite, removed and replaced capacitor, tested unit through DLMS and diagnostic cycles, working well now. Capacitor w11395618 $123.60Tax $10.14Supplies $14.50Hc $129.95Labor $179.95Total job $458.14No return on parts Auth total due $458.14 #L9U3R4"
We serviced a
SAMSUNG DRYER
Model DVE50R5200
Near Colorado Springs, CO 80917
Kris
Job Details: 01/05/2024
ran test op unit is working to spec at this time.
We serviced a
SAMSUNG WASHER
Model WF50K7500AW/AZ
Near Colorado Springs, CO 80922
Kris
Job Details: 01/05/2024
ran test op found drain pump access port was not tightened. reseated ran test op all ok at this time.
We serviced a
JENNAIR REFRIGERATOR
Model JFFCC72EHL01
Near Colorado Springs, CO 80924
Aaron
Job Details: 01/05/2024
"Tested unit through diagnostics, harvest cycle passed, fill test passed, good air push to the ice maker, discussed with techline, front dispenser UI controls ice maker functions, Needs UI assembly SR7738175130UI control w11533211 $263.96Tax $21.64Supplies $14.50Hc $149.95Labor $259.95Total job $710.0030 day estimateNo return on parts Auth 149.95 hc #K93NRF"
We serviced a
SUBZERO REFRIGERATOR
Model 601R/S
Near Pueblo, CO 81004
James
Job Details: 01/05/2024
no error codes observed. service light was on but could have been from dirty coils that cust cleaned. checked temps. all temps ckok reset light. collected 149.95 $149.95 CK Auth# LVHKM3
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GBS0
Near Colorado Springs, CO 80924
Aaron
Job Details: 01/05/2024
"Diverter is shorted out, lower spray arm is the only water movement in the unit, Needs motor sump assembly. Approved onsite. Removed and replaced motor sump assembly, tested and working well, no leaks, installed litmus strip. Motor sump assembly w11665769 $217.94Tax $17.87Supplies $14.50Hc $129.95Labor $259.95Total job $640.21No return on parts Auth total due $640.21 #3NUA44"
We serviced a
WHIRLPOOL WALL OVEN
Model WOC54EC0HS20
Near Colorado Springs, CO 80927
Aaron
Job Details: 01/05/2024
"Customer states excessive moisture is between panels in door. Adjusted door receiver so the door shuts tighter to cavity. Discussed situation with techline, recommend customer covering product that is high in moisture content as well. Unit working as designed. SR7738171636"
We serviced a
SAMSUNG WASHER
Model WA55A7700AV/US
Near Colorado Springs, CO 80918
Brandon
Job Details: 01/05/2024
"Errors sdc, checked PCB version up to date, detergent nozzle on tray sticking, replaced detergent assy and tested op all checks ok hass oqc passed"
We serviced a
SAMSUNG DISHWASHER
Model DW80B7070UG/AA
Near Colorado Springs, CO 80920
Brandon
Job Details: 01/05/2024
Replaced covers and tested op all checks ok hass oqc passed
We serviced a
WHIRLPOOL RANGE
Model WFE505W0HW2
Near Trinidad, CO 81082
James
Job Details: 01/05/2024
installed preordered parts
We serviced a
GE DRYER
Model GTX22GASK1WW
Near Pueblo, CO 81005
David
Job Details: 01/05/2024
Replaced drum and top bearing Ran and running quietly
We serviced a
SAMSUNG WASHER
Model WA52M7750AW/A4
Near Colorado Springs, CO 80910
Mathew
Job Details: 01/05/2024
Upon arrival I informed Cx of service charge due to being out of warranty and Cx told me not to diagnose/ did not want to move forward with service.
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Colorado Springs, CO 80905
Mathew
Job Details: 01/05/2024
"Found squeeking rollers. Replaced all four support rollers, test op all okay."
We serviced a
SAMSUNG MICROWAVE DRAWER
Model ME17R7021ES/AA
Near Colorado Springs, CO 80908
Brandon
Job Details: 01/05/2024
"Replaced door, tested op all checks ok"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Grand Junction, CO 81507
James R
Job Details: 01/05/2024
Put into diagnostics has no error codes. Checked restriction again with test kit W11224254 checked ok. came off everytime within a few seconds. Checked also with manometer is .43 good within specs. Checked voltage at control when heating 254 vac good. 23.4 amps. good. Timed dry or auto dry hi temp. Put load of wet cloths in timed dry did fine auto dry would time down then back up sensing the dryness of cloths. Working as should. Customer indicates unit will stop it shows time on the display tries to restart and it wont. Opens door and lets cool down then it will start. If uses a lower heat doesnt have the issue. calloed tech line. did some checked pwr good suggest replacing thermal fuse. Did W10909685 SR# 7738175820; used 1 W10909685 (FUSE-THRML) from stock
We serviced a
SAMSUNG REFRIGERATOR
Model RF22K9381SR/AA
Near Peyton, CO 80831
Brandon
Job Details: 01/05/2024
"Errors 71c, 39c, suspected gas leak, recommend dye dryer"
We serviced a
BOSCH DISHWASHER
Model SHPM65W55N/01
Near Monument, CO 80132
Kris
Job Details: 01/05/2024
installed heat pump ran test op all ok at this time.
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Albuquerque, NM 87123
Jason
Job Details: 01/05/2024
installed control and calibrated unit for wash preformance unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ01
Near Albuquerque, NM 87108
Jason
Job Details: 01/05/2024
installed part unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Trinidad, CO 81082
James
Job Details: 01/05/2024
Found doors needed to be aligned to keep freezer seal from hitting refrigerator door when closing. adjusted hinges leveled unit and tested all operations check okay
We serviced a
MAYTAG WASHER
Model MVW7230HW2
Near Trinidad, CO 81082
James
Job Details: 01/05/2024
"installed preordered ui. recalibrated unit, tested all ops test good"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Albuquerque, NM 87120
Larry
Job Details: 01/05/2024
cx- not draining - inspected unit - found drain pump failed - replaced with pre id parts - unit tested good
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Rio Rancho, NM 87124
Larry
Job Details: 01/05/2024
CX cancelled call
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS2
Near Rio Rancho, NM 87124
Larry
Job Details: 01/05/2024
cx complaint - leaking - underneath - inspected unit - found tubr gasket misaligned - adjusted gasket - tested good
We serviced a
JENN-AIR WALLOVEN
Model JMW3430WS02
Near Sandia Park, NM 87047
Jason
Job Details: 01/05/2024
found metal by turn tabel was flexed causing turntable motor to rub corrected fittment unit checks ok
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Pueblo, CO 81001
Jessie
Job Details: 01/05/2024
C71 freezer temp abnormal. Found freezer fan not operating pushing air ove to fridge and freezer. Pulled apart to verify. Van was tough to turn. Got to release and operate. Needs new fan.Evap fan#da31-00342a $199.16Tax $16.33Sc $129.95Msrp $14.50Labor $179.95Total $539.89No return on partsCustomer to think about repair Paid cash
We serviced a
JENN-AIR REFRIGERATOR
Model JUCFP242HL00
Near Breckenridge, CO 80424
Antonio
Job Details: 01/05/2024
Installed new acu and icemaker unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW
Near Breckenridge, CO 80424
Antonio
Job Details: 01/05/2024
Installed new ui panel and acu unit tested good
We serviced a
KITCHENAID WALLOVEN
Model KODE500ESS20
Near Grand Junction, CO 81505
James R
Job Details: 01/05/2024
Signed disclaimers. Replaced inner glass. Heated up oven operating as should. Please fill out whirlpool tech satisfactrion survey. Thank You.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Colorado Springs, CO 80919
Glenn
Job Details: 01/05/2024
"Customer indicates frost issue in freezer has not returned, however; ice in bucket is still globbing together and becomes one big ball of ice. Techline: Suggest customer dump ice at least once per week, as this is normal. Adjusted door gasket."
We serviced a
JENN-AIR WARMING DRAWER
Model JWD3030EX00
Near Larkspur, CO 80118
Glenn
Job Details: 01/05/2024
"New Drawer was received damaged, however, was able to install New Rails & Old Drawer. Customer informed me that she felt the drawer seemed very thin metal and flimsy, and is concerned about it being able to hold heavy cooking dishes. I suggested she reach out to the seller. All OPS Test:OK"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS1
Near Larkspur, CO 80118
Glenn
Job Details: 01/05/2024
"F8E4 Error , Water found in drip tray. Emptied water from tray. Reseat connections to PCB. Ran 5 Diag Cycles, no leaks or Errors. Possible soap buildup issue. Suggest customer try using a different soap and see if problem continues. Also suggest make sure to run water at sink until hot, then start unit."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Monument, CO 80132
Glenn
Job Details: 01/05/2024
"Removed Washer from Pedestal, installed 4 feet. Tested unit using 6 large towels, high speed spin. All OPS Appear to be OK at tghis time. Techline: Provided Model / Serial Tag info for Pedestal < Suggest customer call Customer Service to get replacement pedestal and installer scheduled for its replacement. > 800-253-1301> SR# 7738172641"
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Monument, CO 80132
Kris
Job Details: 01/05/2024
helped glenn
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Rio Rancho, NM 87144
Larry
Job Details: 01/05/2024
cx complaint - washer gears are grinding - inspected unit - installed gearcase and belt - unit tested good
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Albuquerque, NM 87105
Larry
Job Details: 01/05/2024
CX complaint - Dryer not heating - Inspected unit and found the thermal fuse open - Replaced with TS and tested good - Unit is good to go; used 1 W10900067 (CUTOFF-TML) from stock
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Pueblo West, CO 81007
Brandon
Job Details: 01/04/2024
Replaced parts and tested op all checks ok unit is heating now
We serviced a
MAYTAG WASHER
Model MVWC465HW4
Near Granby, CO 80446
Antonio
Job Details: 01/04/2024
Installed new shocks unit tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM
Near Granby, CO 80446
Antonio
Job Details: 01/04/2024
Installed new evap fan unit tested good
We serviced a
KITCHENAID TRASH COMPACTOR
Model KTTS505EPA2
Near Tabernash, CO 80478
Antonio
Job Details: 01/04/2024
"Installed new counter, wheels and pedal unit tested good"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS
Near Fraser, CO 80442
Antonio
Job Details: 01/04/2024
"Installed new acu, float, and valve unit tested good"
We serviced a
MAYTAG RANGE
Model MGR6600FZ6
Near Albuquerque, NM 87110
Jason
Job Details: 01/04/2024
installed part unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Albuquerque, NM 87110
Jason
Job Details: 01/04/2024
installed inlet valve unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Albuquerque, NM 87110
Jason
Job Details: 01/04/2024
installed parts unit checks ok
We serviced a
AMANA DRYER
Model NED4655EW1
Near Albuquerque, NM 87110
Jason
Job Details: 01/04/2024
checked unit tempature and airflow both check ok
We serviced a
KITCHENAID COMPACTOR
Model KTTS505EPA0
Near Albuquerque, NM 87122
Jason
Job Details: 01/04/2024
"checked unit found switch bracket bent, adjusted fitment unit opperation checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Albuquerque, NM 87105
Larry
Job Details: 01/04/2024
cx complaint water dispensing slowly - inspected unit - found water pressure low - replaced valve and housing - unit tested good
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMW0
Near Albuquerque, NM 87120
Larry
Job Details: 01/04/2024
"cx complaint - spray arm not working - inspected unit - found sump not working - reploaced control, ui, and sump - unit tested good"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Los Ranchos de Albuquerque, NM 87114
Larry
Job Details: 01/04/2024
cx complaint - vibration during the cycle - inspected unit and found nut on drive pulley loose - applied locktight and secured nut - unit good to go
We serviced a
MAYTAG WASHER
Model MVWB865GW0
Near Rio Rancho, NM 87144
Larry
Job Details: 01/04/2024
cx complaint - makes a squeaking noise while on the spin cycle.- inspected unit - found gearcase failed - replaced pmd parts - unit tested good
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Rio Rancho, NM 87144
Larry
Job Details: 01/04/2024
cx complaint - not cleaning dishes - inspected unit - found motor not ruinning - replaced pmd parts
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325FDAB06
Near Albuquerque, NM 87111
Jason
Job Details: 01/04/2024
installed parts listed unit checks ok
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Edgewood, NM 87015
Jason
Job Details: 01/04/2024
installed control unit checks ok
We serviced a
DACOR DOWNDRAFT VENT
Model RV36W
Near Elbert, CO 80106
Kris
Job Details: 01/04/2024
lubricated fan all ok at this time.
We serviced a
SAMSUNG RANGE
Model NX60A6511SS/AA
Near Pueblo West, CO 81007
Brandon
Job Details: 01/04/2024
"Not sparking, replaced electrode and tested op all checks ok hass OQC failed wired and wireless"
We serviced a
VIKING WALL OVEN ELECTR
Model RSVOE330SS
Near Colorado Springs, CO 80904
Roman
Job Details: 01/04/2024
"Ran the oven and error came up right away. Pulled the unit out and ohmed out heating elements and temp sensor. Cooling fan working, All okay. Tapped on the relay of the temp sensor and got the oven to heat up. Recommend replacing the control board. Control board #046142-571 $712.58Paid sc $"
We serviced a
KITCHENAID DISHWASHER
Model KDFE104KPS0
Near Colorado Springs, CO 80909
Roman
Job Details: 01/04/2024
Ran the drain cycle and their is something stuck inside it and the filter. Removed plastic from the filter and ran the dishwasher again. Noise went away after running a couple times so whatever was in there got flushed out. Paid sc $129.95 CC Auth# 3HFF44
We serviced a
GE REFRIGERATOR
Model GNE29GMKJES
Near Eagle, CO 81631
Erik
Job Details: 01/04/2024
connect to smartHQ service:F203 FF evap defrost abnormalF713X3 FF door open 15 min + F714 FF door open for 60 min +** suspect excessive frost from door openingdefrost manually and test: possible slow leak - correct sensor position and resume cooling - IF FREEZE RETURNS IN FF COMPARTMENT: EVAP LEAK(excessive frost in FF evap compartment)* see quick pics
We serviced a
MAYTAG DRYER
Model MED5630HC1
Near Glenwood Springs, CO 81601
James R
Job Details: 01/04/2024
"Signed disclaimer Tore apart found faulty heat element and idler pulley starting as well as thermal. customer paid $437.89 Auth code T9RXEA Please fill out whirlpool tech satisfaction survey. Thank You.; used 1 WP3387747 (Element (Front Blower)), 1 280148 (CUTOFF-TML), and 1 W10837240 (Idler) from stock"
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Carbondale, CO 81623
James R
Job Details: 01/04/2024
Signed disclaimer. Wont pwr on replaced Console and control. Unit came on. Test operation is operating as should. Customer needs to have venting checked restricted. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DISHWASHER
Model MDB4949SDM1
Near Albuquerque, NM 87107
Larry
Job Details: 01/04/2024
cx compliant - soap dispenser not closing - latch broken - customer declined repair - collected service call
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHZ0
Near Colorado Springs, CO 80906
Carlos
Job Details: 01/04/2024
"Removed debris from drain pump, runs all ok. Cx pay sc fee $129.95 CC Auth# AHL9V9"
We serviced a
MAYTAG DRYER
Model MED835DW3
Near Pueblo, CO 81004
David
Job Details: 01/04/2024
Checked dryer Found idler pully squealing Idler pully and shaft very sticky and would not turn very good Cleaned and a light lubeRan dryer and is not squealing
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Rifle, CO 81650
James R
Job Details: 01/04/2024
Prined labels took pics ready to send.
We serviced a
SAMSUNG RANGE
Model NX58K7850SS/AA
Near Monument, CO 80132
Jerimiah
Job Details: 01/04/2024
"Bake igniter not glowing needs replacing. Broil pipe not fully igniting around unit, customer wants igniter replaced. Holding off for spousal review. Labor will be $199.95 upon return service if chosen to do so. Charging service call $129.95 CC Auth# 4HY3ACDG94-01012A bake igniter $296.78"
We serviced a
SAMSUNG MICROWAVE
Model ME21M706BAG/AA
Near Colorado Springs, CO 80916
Jerimiah
Job Details: 01/04/2024
"Readjusted door hooks, had Cust check out, seems to be better but if problem persists may need replacement door assy listed below. Unit check ok. DE94-04094D door assy."
We serviced a
WHIRLPOOL WASHER
Model MHW3505FW1
Near Colorado Springs, CO 80921
Glenn
Job Details: 01/04/2024
"not turning on, control panel turns off when turning washer on all the time. Stacked Unit w/ Dryer on Top, not able to further diagnose machine internally w/o having dryer removed. Diagnostics does funtion, ran entire diag cycle to C08, then shuts off. Techline: Suggest cycle power off / on , Unit is now working again. If problem continues, possible UI & Main PCB. Would also require Helper (2X Labor) to remove dryer. Customer paid SC Fee $149.95 Cell Used for CC: 719 728-9434, Autho# 4V3R3HSR# 7738168697"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Colorado Springs, CO 80921
Glenn
Job Details: 01/04/2024
"Bad Motor, Install New Sump & Motor assy. All OPS Test:OK, No Leaks, Installed Leak detector for safety."
We serviced a
WHIRLPOOL WASHER
Model n/a
Near Pueblo West, CO 81007
David
Job Details: 01/04/2024
"Checked washer Replaced cam, actuator, and capRan diagnostics All ran good"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Albuquerque, NM 87121
Larry
Job Details: 01/04/2024
cx complaint - range overheating - Inspected unit and found the unit is heating to temp bt the door gets very hot to the touch - Explained SP-W10917778 to cx - Unit is operating as designed
We serviced a
MAYTAG DRYER
Model MDE9700AYW
Near Yoder, CO 80864
Aaron
Job Details: 01/04/2024
"Idler wheel, rollers, and belt have worn, unit full of lint, approved onsite, removed lint and replaced components, tested and working well now. Repair kit 4392067 $75.90Tax $6.22Supplies 14.50Hc $129.95Labor $199.95Total job $426.52No return on partsAuth total due $426.52 #YPTVAN"
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC5
Near Pueblo West, CO 81007
David
Job Details: 01/04/2024
"Replaced drive assembly, rotor, slider, and suspension rods Ran diagnostics cycle All good"
We serviced a
MAYTAG WASHER
Model WTW4816FW3
Near Pueblo, CO 81008
David
Job Details: 01/04/2024
"Ticket had wrong model number, so the agitator that was sent is wrong. Screw had come out and the auger came off. Reassembled auger and agitator. Ran diagnostics cycle All good"
We serviced a
SUBZERO REFRIGERATOR
Model 632/S 3
Near Monument, CO 80132
Jessie
Job Details: 01/04/2024
Replaved cond fan motor and blade. Replaced refrig evap and Drier. Replaced freezer evap and Drier. Ran vacuum pump and made sure pressure hold. Charged unit and monitored. All ok
We serviced a
KITCHENAID DISHWASHER
Model KDTM354DSS5
Near Colorado Springs, CO 80918
Glenn
Job Details: 01/04/2024
"No Com at UI, SRC 122VAC , 5VDC to UI, Bad UI Control, possible bad Main PCB as well. UI Control - W10803367 $301.42 , Tax $24.72 , MPS $14.50 , Labor $199.95 , SC $149.95 , Declined Estimate, Paid SC Fee $149.95, Phone: 407 761-3510 , Autho# EELC93"
We serviced a
SPEEDQUEEN DRYER
Model ADE3SRGS175TW01
Near Peyton, CO 80831
Kris
Job Details: 01/04/2024
cx does not want to go through with repair cx paying 129.95 ran test op unit has bad heating element. 964p3
We serviced a
THERMADOR DOUBLE WALL OVEN
Model MEDMC301WS/04
Near Colorado Springs, CO 80906
Roman
Job Details: 01/04/2024
"Ran the unit and it will not heat up, reset the high limit thermostat and Trinas it again. Unit started heating up. Recommended to cx not to use self clean."
We serviced a
KITCHENAID REFRIGERATOR
Model KBSN602ESS
Near Colorado Springs, CO 80906
Carlos
Job Details: 01/04/2024
"Ran test op, broken wire, reattached runs all ok"
We serviced a
GE WALL OVEN ELECTR
Model PT916BM1BB
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 01/04/2024
"Installed replacement blower, unit check ok, charged labor $189.95 $209.95 CC Auth# 49U93P"
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JZ2
Near Calhan, CO 80808
Aaron
Job Details: 01/04/2024
"Removed and replaced control and sensor, tested unit at 350f, calibrated +20f. Working and heating well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5900SR/AA
Near Colorado Springs, CO 80916
Brandon
Job Details: 01/04/2024
"Error 41c, replaced f hub, PCB and camera French assy, tested op all checks ok hass OQC passed"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo, CO 81001
James
Job Details: 01/04/2024
arrived to unit stuck in cycle trying to drain. cleared control and ran system recalibration. tested ops all ckok no errors found.
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Pueblo, CO 81008
James
Job Details: 01/04/2024
installed ordered part tested ops all ckok. unit not able to be installed fully due to drain hose placement in cabinet. advised cust that they will have to reposition drain hose to allow unit to slide fully back into cabinet without pinching hose
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5001SR/AA
Near Pueblo West, CO 81007
James
Job Details: 01/04/2024
"post for freezer handle backed out, which caused handle to fall off. secured standoff and reattached. checked ops all ckok"
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Pueblo, CO 81001
Brandon
Job Details: 01/04/2024
"Found burnt marks on magnetron, replaced mag and cap assy, tested op all checks ok"
We serviced a
SAMSUNG REFRIGERATOR
Model RF4287HARS/XAA
Near Pueblo, CO 81001
Brandon
Job Details: 01/04/2024
"No errors, screen and dispenser was locked on display, showed cx how to change, tested op all checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM06
Near Colorado Springs, CO 80922
Mathew
Job Details: 01/04/2024
Replaced control. Test op all okay.
We serviced a
SAMSUNG DRYER
Model DVE50A8600V/A3
Near Colorado Springs, CO 80922
Mathew
Job Details: 01/04/2024
"Found bad element. Replaced element and test op, unit is only getting 120v from L1 to L2. From wall Im getting 120v L1 and 100v L2. Suspect bad power chord as well. Could not run hass as unit will not power up."
We serviced a
SAMSUNG RANGE
Model NX58H5600SS/AA
Near Colorado Springs, CO 80922
Mathew
Job Details: 01/04/2024
Replaced igniter and sensor. Test op all okay. Paid 209.95 labor via check. $209.99 CK Auth# 44CN9K
We serviced a
SAMSUNG WASHER
Model WF45A6400AV/US
Near Colorado Springs, CO 80921
Mathew
Job Details: 01/04/2024
"Replaced all parts, test op all okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF30HBEDBSR/AA
Near Monument, CO 80132
Mathew
Job Details: 01/04/2024
Found buildup in ice room. Replaced all parts and test op all okay. Unit not hass compatible.
We serviced a
BOSCH DISHWASHER
Model SHPM78Z54N/22
Near Larkspur, CO 80118
Jessie
Job Details: 01/04/2024
Replaced fan and vent. Test op. All ok
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Pueblo, CO 81004
Brandon
Job Details: 01/04/2024
"Customer complaint is washer only works on normal cycle, hot water is not connected and unit requires hot water to work properly hass OQC passed"