We serviced a
GE COOKTOP
Model JGP5536DL1BB
Near Peyton, Colorado 80831
David
Job Details:
03/03/2026
"Checked cooktop, couple of burners not sparking, cleaned ignitors, adjusted low flame setting. Sparking and igniting correctly, low is much better."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2623AB8
Near Pueblo, Colorado 81008
Domingo
Job Details:
03/03/2026
Replaced control ice maker defrost tube assembly harness test it and it worked no abnormal noise
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS335SDHM07
Near Peyton, Colorado 80831
Aaron
Job Details:
03/03/2026
"Evaporator fan motor bearings are loud, removed and replaced motor , used sealer to aid with vibration, removed and replaced kickplate, cleaned condenser, working well now. Advised customer of situation and survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5201SG/AA
Near Pueblo, Colorado 81004
Domingo
Job Details:
03/03/2026
I was about to call techline when I found another leak by the evaporator joints at the top I brace that and pressurize it at 300 psig waited 15 min nothing drop I vacuum and charge to weight it passed hass
We serviced a
BOSCH DISHWASHER
Model SHPM78Z54N/22
Near Larkspur, Colorado 80118
Ryan
Job Details:
03/03/2026
Customer did not have extension piece available that was agreed upon. Did what i could with his drain hose to keep debris from disposal backflowing into unit. Changed both pumps and tested operation fine with no errors. Customer was unavailable after service and was in a meeting. To remove hard water scale from unit customer will need to run several cleaning cycles with dishwasher cleaning tablets.RK
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80920
Earl
Job Details:
03/03/2026
Install the new control board ran the unit through a calibration unit is operating properly at this time
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC503ESS01
Near Colorado Springs, Colorado 80908
Charles
Job Details:
03/03/2026
"Need ice maker W10873791, Service fee $149.95, Labor $199.95, MPS $14.50, Part $143.24, Tax $11.75, Total $519.39, paid autho HVP3Y9"
We serviced a
WHIRLPOOL ICEMAKER
Model KUIX335JPS02
Near Breckenridge, Colorado 80424
Antonio
Job Details:
03/03/2026
Installed new hoses and calamps unitvtested good
We serviced a
WHIRLPOOL COOKTOP
Model WCE55US6HB00
Near Colorado Springs, Colorado 80918
David
Job Details:
03/03/2026
"Checked cooktop, found ground wire in junction box loose and moving a little. Resecucured ground conductor so it is tight and will not loose contact. Called safety team case number 22671901."
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Medford, Oregon 97504
Thomas
Job Details:
03/02/2026
Replaced display assembly. Ran tested okay no leaks
We serviced a
JENN-AIR OVEN
Model JES9750AAB
Near Roseburg, Oregon 97471
Chris
Job Details:
03/02/2026
The broiler will not cycle the relay is stuck. Parts are not available.
We serviced a
BOSCH MICROWAVE OVEN
Model HMC87152UC/06
Near Fruita, Colorado 81521
James R
Job Details:
03/02/2026
Helped clint. Removed unit from wall. Removed outer panels and replaced door switches. Re- assembled unit and installed is much better but need to order another door new one is damaged.
We serviced a
WHIRLPOOL DRYER
Model WGD8127LC4
Near Eagle, Colorado 81631
Antonio
Job Details:
03/02/2026
Installed new acu and then ran a cycle for proper operation and unit tested good Also let cx know that his ducting is clogged and needs cleaned
We serviced a
SAMSUNG WASHER
Model WF42H5200AF
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
03/02/2026
"Not draining, drain pump propeller broke off motor need pump, part $227.10, labor $219.95, mps $14.50, tax $18.62"
We serviced a
SAMSUNG DISHWASHER
Model DW90F89T0USRAA
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
03/02/2026
"Error 5c, found extension on drain hose and it was crimped from installers, situated so it is not crimped and tested operation all checks ok hass passed, recommended moving dishwasher drain pipe close to dishwasher so extention is not needed"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Los Lunas, New Mexico 87031
Larry
Job Details:
03/02/2026
CX complaint - Washer keeps running untill I unplug it - Inspected unit and found F3E1 error - Replaced control ran auto calibration but could not fully test beacuse unit was uninstalled in the garage - Unit should be good to go
We serviced a
PROFILE REFRIGERATOR
Model PSB42YSNKSS
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
03/02/2026
"replaced part, cust to monitor"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
03/02/2026
"Circulation motor is shorted out, removed and replaced motor sump assembly, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
03/02/2026
"Start and cancel buttons are intermittently working, removed and replaced ui console assembly, tested, working well now, verified by customer. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DRYER
Model WED6120HW2
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
03/02/2026
"Blower wheel is stripped on motor shaft, rollers and idler have worn from use, removed and replaced components motor, blower, and repair kit, tested unit, working and heating well now. Advised customer of situation and survey."
We serviced a
SAMSUNG MICROWAVE
Model ME21DG6300SRAA
Near Colorado Springs, Colorado 80924
Brandon
Job Details:
03/02/2026
"Replaced bulb, pcb and body latch, I am good, tested operation.All checks ok"
We serviced a
SAMSUNG DRYER
Model DVE46BG6500VA3
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
03/02/2026
"Replaced drum, rollers. Unable to test unit not hook up in garage"
We serviced a
SAMSUNG MICROWAVE
Model ME16A4021AS/AA
Near Colorado Springs, Colorado 80927
Brandon
Job Details:
03/02/2026
"Cx concerned blower not working properly, checked and checked for obstructions all checks ok tested operation, frame physical damage not covered"
We serviced a
SAMSUNG DRYER
Model DVE50BG8300VA3
Near Peyton, Colorado 80831
Brandon
Job Details:
03/02/2026
"Belt damaged, replaced belt and tested operation all checks ok hass passed"
We serviced a
LG REFRIGERATOR
Model LRMXS2806S/05
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
03/02/2026
"Replaced door, display and sub pcb, tested operation, ice maker cycle all checks ok"
We serviced a
SAMSUNG DRYER
Model NA
Near Colorado Springs, Colorado 80910
Brandon
Job Details:
03/02/2026
"Belt came off, put belt back on pulley amd tested operation all checks ok $149.95 CC Auth# R3F4UV"
We serviced a
WHIRLPOOL RANGE
Model WFES3330RW0
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
03/02/2026
Installed all harnesses ran test cx will observe
We serviced a
GE DRYER
Model GFD55ESSN2WW
Near Avon, Colorado 81620
Erik
Job Details:
03/02/2026
ACCESS WITH DOOR CODEinstall door latch and spacer/ test: PASSJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
WHIRLPOOL VENT HOOD
Model KVUB406GSS03
Near Monument, Colorado 80132
Ryan
Job Details:
03/02/2026
Installed new clip for vent cover. All now checks ok. RK
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
03/02/2026
Installed control board ran calibration and tests runs all ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
03/02/2026
Installed control board ran calibration and tests runs all ok.
We serviced a
MONOGRAM REFRIGERATOR
Model ZISS480DNMSS
Near Colorado Springs, Colorado 80921
Charles
Job Details:
03/02/2026
Replaced inlet valve
We serviced a
BEKO DISHWASHER
Model DUT36522W
Near Colorado Springs, Colorado 80908
Charles
Job Details:
03/02/2026
"Unit full of water, did cancel drain, unit emptied, started cycle, filled, washed, drained. Advised customer on cancel drain option. Advised to monitor, if fills when not in use will need inlet valve. Service fee paid check #9201 autho 3M44FU"
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Colorado Springs, Colorado 80910
Carlos
Job Details:
03/02/2026
Installed control runs all ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDPS7024RZ0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/02/2026
"F8E4 error code, plastic piece binding spray arm, water getting past door gasket, removed and replaced gasket, tested unit through diagnostics, working well now, no leaks, raised front legs. Advised customer of situation and survey."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRFS282LAF2
Near Medford, Oregon 97504
Thomas
Job Details:
03/02/2026
Replaced main control board and UI. Ran tested okay with customer present. Advised customer of survey
We serviced a
MIELE COFFEE MACHINE
Model CVA6805
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
03/02/2026
"cust ordered a brew unit, want to see if that fixes issue, cust to call back if needed, did get unit to finish the descale...autho no. C4J3KX"
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Jacksonville, Oregon 97530
Chris
Job Details:
03/02/2026
"The rotor bolt had come off completely. Replaced the gear case, clutch and slider."
We serviced a
BOSCH MICROWAVE
Model HMC80252UC/05
Near Colorado Springs, Colorado 80920
Charles
Job Details:
03/02/2026
Replaced both switch groups and fuse. Paid labor autho TL9MW9
We serviced a
GE RANGE
Model GRF400SVSS
Near Colorado Springs, Colorado 80918
Earl
Job Details:
03/02/2026
I installed the new burner and infinite switch and tested unit is operating properly.At this time
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
03/02/2026
Arrived and cx complaint of constantly draining. Removed failed control. Installed new control. Recalibrate washer. Ran quick cycle. Unit is functioning now as designed. No further issues noted. Informed cx of review process.
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PPS02
Near Albuquerque, New Mexico 87120
Larry
Job Details:
03/02/2026
Installed parts lsited and tested good - Unit is good to go
We serviced a
WHIRLPOOL RANGE
Model WSGS7530RZ0
Near Bend, Oregon 97701
Levi
Job Details:
03/02/2026
Replace spark modules control boards sensors and valve tested and it seems to be working good and informed customer to use it and we'll see how perfect it is.
We serviced a
WHIRLPOOL STACK UNIT
Model WET4024HW
Near Beaver Creek, Colorado 81620
Erik
Job Details:
03/02/2026
USER ERROR - COLD WASH WORKS AND HOT WASH WORKSJOB COMPLETE
We serviced a
KITCHENAID WALL OVEN
Model KOES530PSS00
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/02/2026
"F9E0 miswire,F1E1 relay error codes in diagnostics, corrected wiring in junction box, good power and polarity, tested unit at 350f bake cycle, working and heating well now. Advised customer of situation and survey."
We serviced a
KITCHENAID RANGE
Model KFGC558JSS07
Near Sisters, Oregon 97759
Richard
Job Details:
03/02/2026
"Replaced burner assembly, and spark igniter, & module cycle tested all tested fine at time of repair"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/02/2026
Arrived and cx complaint of draining constantly. Removed failed control and installed new control. Recalibrate unit. Tested on short cycle. Washer is functioning now as designed. No further issues noted. Informed cx of review process.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/02/2026
Arrived and cx complaint of draining constantly. Removed failed control. Installed new control. Recalibrate unit. Ran short cycle. Washer is functioning now as designed. Informed cx of review process
We serviced a
SAMSUNG DISHWASHER
Model DW80B7070AP/AA
Near Redmond, Oregon 97756
Richard
Job Details:
03/02/2026
Picked up part for return wrong part ordered need to return part ordered
We serviced a
MAYTAG DRYER
Model MEDB765FW0
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/02/2026
Arrived and cx complaint of not heating. Replaced parts provided. Tested dryer. Unit is functioning now as designed. Informed cx of review process
We serviced a
WHIRLPOOL DISHWASHER
Model WDT751SAPZ2
Near Colorado Springs, Colorado 80905
Carlos
Job Details:
03/02/2026
Installed track and nut all ok
We serviced a
WHIRLPOOL RANGE
Model WFES5030RZ0
Near Peyton, Colorado 80831
Aaron
Job Details:
03/02/2026
"Control display is intermittently working, removed and replaced control, tested unit, working and heating well now, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Pueblo, Colorado 81001
James
Job Details:
03/02/2026
Found loose blower wheel getting stuck in housing secured and tested ops all ckok
We serviced a
WHIRLPOOL WASHER
Model WFW5720RR0
Near Pueblo, Colorado 81008
James
Job Details:
03/02/2026
Found loose shock causing poor spin. Secured and tested all ops test good
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Pueblo, Colorado 81001
James
Job Details:
03/02/2026
"Found loose pulley causing intermittent spinning issues secured and tested ops all ckok advised cust on proper loading, sorting and cycle usuage"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Albuquerque, New Mexico 87109
Jason
Job Details:
03/02/2026
Checked unit found it was just the vent fan running. fan will run up to 48 hrs or until door is opend. this is normal operation for unit. spoke to cx about review
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Monument, Colorado 80132
Ryan
Job Details:
03/02/2026
Cleaned out clogged filter and see that unit has been oversudsing causing subs overflow onto floor. Explained use and care to customer and thery need to run several cleaning cycles and use less detergent. All else checks ok. RK
We serviced a
SUBZERO REFRIGERATOR
Model 532
Near Colorado Springs, Colorado 80915
Ralph
Job Details:
03/02/2026
REPLACED PART UNIT CHECKED OKAY
We serviced a
MAYTAG M/W OTR
Model MMV4205DE4
Near Fruita, Colorado 81521
Clint
Job Details:
03/02/2026
"Customer signed disclaimer and recieved parts ordered. Installed magnetron, capacitor, and diode ran unit no issues detected."
We serviced a
GE REFRIGERATOR
Model GFE28GYNBFS
Near Colorado Springs, Colorado 80924
Ryan
Job Details:
03/02/2026
Adjusted door so that it closes better. Seal and hinges are fine. The problem is that the cabinet has settled and is not square. Leveled unit the best i could. Told customer this is the best it will get and replacing parts will not help any. RK109.95Auth NEPYAM
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW
Near Sandy, Oregon 97055
Austin
Job Details:
03/02/2026
3/2/26 AB : removed and replaced main mother board and fixed harness issues. Tested machine and found no further issues. Service complete
We serviced a
MAYTAG WASHER
Model MVW6230HW1
Near Albuquerque, New Mexico 87122
Jason
Job Details:
03/02/2026
"Installed cam, agitator, belt, and actuator. ran quick wash cycle unit operation checks ok. spoke to cx about review"
We serviced a
GE DISHWASHER
Model GDP670SYV0FS
Near Fruita, Colorado 81521
Sean
Job Details:
03/02/2026
Verified the unit information & customer signed disclaimer.Opened the unit and removed the old gasket .Cleaned up the gasket bracket inside the washer. Installed the new gasket. Tested the unit it ran a rinse cycle without and leaked.Removed the door. Removed the inside door panel and removed the control . Cleaned up the aria around the control.Installed the new control and reassembled the unit. Installed the unit and tested. Ran the unit on a rinse cycle and the unit tested good.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Albuquerque, New Mexico 87112
Jason
Job Details:
03/02/2026
Checked unit found unit is operating as designed at this time drain hose is just tapping back of machine. unit checks ok. spoke to cx about review
We serviced a
MAYTAG DRYER
Model MED3500FW1
Near Sandia Park, New Mexico 87047
Jason
Job Details:
03/02/2026
Checked unit found unit needs repair kit SC$184.95MPS$17.50LABOR$209.95REPAIR KIT#4392067$78.30TX$25.99TOTAL$516.69CX TO THINK OVER REPAIR Auth code: FVLMK9$184.95
We serviced a
BOSCH DISHWASHER
Model SHP65CM6N/25
Near Grand Junction, Colorado 81503
Sean
Job Details:
03/02/2026
Verified the unit information customer signed disclaimer.Checked the unit and find the spray arm had come off. The center clip was located in the strainer. Reassembled the unit. Showed the customer about the spray arms.Tested the unit good.Thank you .If you Are satisfied with the service I have provided you with today thenPlease go online and fill out a technician survey.It really help let the office know how I am doing .
We serviced a
LG DRYER
Model DLEX8000V
Near Colorado Springs, Colorado 80925
Mathew
Job Details:
03/02/2026
"Replace rollers. Test op, unit working as expected."
We serviced a
SUB ZERO REFRIGERATOR
Model CL4250UFDID/S/P
Near Colorado Springs, Colorado 80919
Charles
Job Details:
03/02/2026
Installed inlet valve assembly
We serviced a
MIELE COFFEE MACHINE
Model CM5310
Near Colorado Springs, Colorado 80919
Charles
Job Details:
03/02/2026
"Getting error to fill bean container when full, spoke to tech line, did variant update to compensate grind amount to resolve issue. Per tech if issue persist replace grind chamber."
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HV07
Near Colorado Springs, Colorado 80938
Aaron
Job Details:
03/02/2026
"Removed and replaced components, tested unit, working and heating well now, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3336SB00
Near Grand Junction, Colorado 81507
Clint
Job Details:
03/02/2026
"Customer signed disclaimer a d recieved lower door hinges and magnetic bracket,installed parts and doors line up and aren't rubbing on freezer door . Also leveled the unit it was leaning forward considerably. PLEASE TAKE TECH SURVEY THANKS.CLINT"
We serviced a
MIELE COFFEE MACHINES
Model CVA7440
Near Avon, Colorado 81620
Erik
Job Details:
03/02/2026
INSTALL/ TEST: PASSJOB COMPLETE
We serviced a
SAMSUNG WASHER
Model WD53DBA900HZA1
Near Colorado Springs, Colorado 80920
Mathew
Job Details:
03/02/2026
"Ran thru diagnostics with Samsung techline. Agent made sure I followed service bulletin instructions on issue. Unit passes OQC. Agent agrees unit is working as intended. Long cycles are typical for heat pump, non vented units. Cycles may be as long as 6 hours. If I come out here again on a call back and find nothing wrong, a service fee of 149.95 will be charged."
We serviced a
KITCHENAID RANGE
Model KSES530SJP0
Near Colorado Springs, Colorado 80917
David
Job Details:
03/02/2026
"Installed ordered parts, oven is heating as designed, cx to monitor."
We serviced a
GE DISHWASHER
Model PDP755SYV6FS
Near Monument, Colorado 80132
Ryan
Job Details:
03/02/2026
Found spray manifold for utensils not connecting with spray tube at back out tub causing a direct spray at door causing it to leak. Made adjustments so that tube and mainfold now mate and unit is no longer leaking. RK
We serviced a
WHIRLPOOL DRYER
Model WED8127LC3
Near Colorado Springs, Colorado 80918
David
Job Details:
03/02/2026
"Installed ordered parts, tested, seams to working good. Cx to monitor."
We serviced a
GE WASHING MACHINE
Model GFW510SCN4WW
Near Avon, Colorado 81620
Erik
Job Details:
03/02/2026
Install inverter and connect to smart HQ for testingUnit spins inverterboard completed job completed
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Colorado Springs, Colorado 80907
Carlos
Job Details:
03/02/2026
Ran calibration cycle ran cycle unit fills up all ok
We serviced a
KITCHENAID RANGE
Model KSES530SJP0
Near Colorado Springs, Colorado 80917
David
Job Details:
03/02/2026
"Installed ordered parts, oven is heating as designed, cx to monitor."
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Colorado Springs, Colorado 80920
Brandon
Job Details:
02/27/2026
"Belt loose on motor, tightened motor and belt and tested operation all checks ok hass passed"
We serviced a
COVE DISHWASHER
Model DW2450
Near Colorado Springs, Colorado 80904
Charles
Job Details:
02/27/2026
Update firmware
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Clifton, Colorado 81520
James R
Job Details:
02/27/2026
Still not filling with enoiugh wtr. Had previously replaced valve and elec control. Put into service diagnostics there are no error codes. Put load of cloths in unit. Normal filled and cloths were setting in wtr. Cancelled cycle and put on deep wtr wash. Filled a couple times then quit filling. Wtr still was not above cloths. Drained. set awhile door locked filled with a bit of wtr then drained. Spun out cloths. Started rinsing filled top of cloths are above wtr level. Took pic. Called tech line with issue. There are no error codes. Is working as designed. Normal wash setting will have 3-4 inches of wtr inside deep wtr wash will be 6-7 inches did check this and it is. Put on normal cycle let go thru is working as designed. 22685201
We serviced a
MAYTAG WASHER
Model MVW5430PBK1
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
02/27/2026
Installed control board and HMI ran tests and calibration runs all ok.
We serviced a
WHIRLPOOL RANGE
Model WFGS5730SZ0
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
02/27/2026
Installed gas tubing no leaks found all ok
We serviced a
COVE DISHWASHER
Model DW2450
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
02/27/2026
completed helper call
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87109
Jason
Job Details:
02/27/2026
unit repair is covered under special project# S153EB Installed control ran calibration and quick wash cycles. unit operation checks ok. spoke to cx about review; used 1 W11603810 (control) from stock
We serviced a
LG REFRIGERATOR
Model LRMDS3006S/02
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
02/27/2026
"Replaced compressor and drier and charged with 60 grams r600, tested operation all checks ok"
We serviced a
LG WASHER/DRYER COM
Model WM6998HBA
Near Pueblo, Colorado 81008
Domingo
Job Details:
02/27/2026
Replaced evaporator assembly test it and and it test it good also unclogged lines that went to the drain pump
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZO
Near Grand Junction, Colorado 81503
Sean
Job Details:
02/27/2026
Verified the unit information & customer signed disclaimer.Checked the unit and found the vent cap had come off.And the unit was leaking from the door.I put the cap back on and checked the unit for anything out of normal. Unit checked out and I tested lt. On a quick wash.Found no more leaking .Unit tested good.Thank you If you are satisfied with the service I have provided you with today and would like to share your experience with others.You can go online to D-3 A-OK Appliance service inc.And fill out a technician survey.Your technician ..Sean.
We serviced a
JENN-AIR DOWNDRAFT VENT
Model JXD7036YS7
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
02/27/2026
Replaced damaged trim . All checks ok. RK
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS26L3AFE
Near Ashland, Oregon 97520
Thomas
Job Details:
02/27/2026
Replaced damper and evap fan motor/blade. Customer will monitor. Advised customer of survey
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
02/27/2026
Installed control board ran calibration and tests
We serviced a
SAMSUNG WASHER
Model WD53DBA900HZA1
Near Ashland, Oregon 97520
Thomas
Job Details:
02/27/2026
"Replaced display, inlet valves and pressure switch. Calibrated washer. Ran tested okay with customer present. No leaks. Advised customer of survey"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFC2353AF7
Near Grand Junction, Colorado 81504
Clint
Job Details:
02/27/2026
Customer recieved part and signed disclaimer. Installed new touch control and tested the functionality of every button. Worked perfectly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
02/27/2026
Installed control board ran calibration and tests
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT348FMES05
Near Medford, Oregon 97501
Levi
Job Details:
02/27/2026
"Replace compressor, Pull the deep vacuum and test it for leaks with nitrogen all tests good recharged with 1.7 oz of r600a. Checked Frost pattern and frost pattern was good"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT348FMES05
Near Medford, Oregon 97501
Levi
Job Details:
02/27/2026
"Replace compressor and evaporator, tested all checks okay. Pressure tested to 250 psi and vacuum down system before recharging. Frost pattern is proper on evaporator and everything is checking good. Unit in storage unit."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5100SRAA
Near Central Point, Oregon 97502
Levi
Job Details:
02/27/2026
Replace compressor and repair two leaks at condenser. Tested and recharged with r600 with 82 g. Tested and all seems to be working.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
02/27/2026
Unit was replace does not need service
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Albuquerque, New Mexico 87111
Jason
Job Details:
02/27/2026
Checked unit found ice maker tray had cracked causing bin to freeze up. installed ice maker and checksed auger operation. unit operation checks ok. spoke to cx about review