We serviced a
GENERAL ELECTRIC OTR MICROWAVE
Model RVM5160DH8WW
Near Colorado Springs, CO 80910
David
Job Details: 11/14/2024
"Replaced mag, diode, cap, and fuse. Tested and is operating as expected."
We serviced a
GE RANGE
Model JBS86SP5SS
Near Fountain, CO 80817
Charles
Job Details: 11/14/2024
Replaced front right duel surface element
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Pueblo, CO 81005
James
Job Details: 11/14/2024
Installed ordered parts tested ops all ckok left litmus
We serviced a
FISHERPAYKEL DISHWASHER
Model DD24DCX6V2
Near Fountain, CO 80817
Charles
Job Details: 11/14/2024
"Installed service kit with board and fan, replaced LCD display board. Started cycle then canceled to ensure drainage."
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Granby, CO 80446
Erik
Job Details: 11/14/2024
missing leg of 120v from outlet - CX is aware - need electrician to get power suppy correctJOB COMPLETECX not available for signature
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ5
Near Bend, OR 97701
Levi
Job Details: 11/13/2024
"Replaced listed parts, tested good. It would lite but the igniter would keep clicking. Now it's good"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW08
Near Medford, OR 97504
Jeff
Job Details: 11/13/2024
Installed door tested machine working as should
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Bend, OR 97702
Levi
Job Details: 11/13/2024
"Found icemaker seaming to be broken in the middle of the harvest mode. Replaced icemaker and valves, tested good"
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Monument, CO 80132
Dvante
Job Details: 11/13/2024
"Check unit. Saw the unit wasnt cleaning properly. Checked under, saw the pin come on the actuator. Did the diagnostic test. All tested ok and working as designed"
We serviced a
WHIRLPOOL RANGE
Model WFE775H0HZ4
Near Eagle Point, OR 97524
Jeff
Job Details: 11/13/2024
Installed parts customer approved looks
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Colorado Springs, CO 80904
Carlos
Job Details: 11/13/2024
Installed tub ran test allok
We serviced a
WHIRLPOOL WALL OVEN
Model WOES5030LZ01
Near Colorado Springs, CO 80908
Aaron
Job Details: 11/13/2024
"Removed and replaced UI console, programmed unit, tested operation, working and heating well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW06
Near Colorado Springs, CO 80911
David
Job Details: 11/13/2024
Replaced icemaker and thermistor. Explained that this type of icemaker checks to see if there is ice in the bin and that could be every half hour if the bin is full. New icemaker seems to be quieter.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Cañon City, CO 81212
James
Job Details: 11/13/2024
Installed preordered parts
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS10
Near Peyton, CO 80831
Jerimiah
Job Details: 11/13/2024
Installed replacement components unit check ok.
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Colorado Springs, CO 80922
Aaron
Job Details: 11/13/2024
"Customer complains of unit shaking violently during spin, inspected unit, found damper not properly engaged to tub, corrected and tested unit through quick cycle, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Colorado Springs, CO 80922
Aaron
Job Details: 11/13/2024
"Customer complains of unit shaking violently during spin, inspected unit, found damper not properly engaged to tub, corrected and tested unit through quick cycle, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Colorado Springs, CO 80923
Aaron
Job Details: 11/13/2024
"Removed and replaced front panel and control, ran unit through diagnostics, working well now, no leaks, installed litmus strip, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Fountain, CO 80817
Carlos
Job Details: 11/13/2024
Installed ice maker and valve all ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ11
Near Eagle, CO 81631
Antonio
Job Details: 11/13/2024
Started to in cut tubing when noticed capillary tub broken going in to fridge called whlp 7740317797 unit is up for review
We serviced a
WHIRLPOOL DISHWASHER
Model WDP730HAMZ0
Near Gypsum, CO 81637
Antonio
Job Details: 11/13/2024
Installed new sump assembly ran a cycle for proper operation and for leaks unit tested good Also advised cx of water strips
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near El Jebel, CO 81623
James R
Job Details: 11/13/2024
N/A disclaimer No water coming in. Checked float was stuck up put to correct position. Test in service diagnostics test operating as should. No error codes reappeared. Put a leak board under unit and took pic. May remove later if no leaks appear. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL RANGE
Model WFE505W0HW5
Near Leadville, CO 80461
Antonio
Job Details: 11/13/2024
Installed new acu turned oven on to 350 degrees and unit tested good
We serviced a
WHIRLPOOL DRYER
Model WED6605MW0
Near Aspen, CO 81611
James R
Job Details: 11/13/2024
Signed disclaimer.Replaced heater and thermal cutoff. Is heating. Checked vent restriction is 25 good. Checked temp vent hooked up with load 148 degrees good. Temp cycling on and off as should. Put some towels in unit. Auto dry sensing is working. switched to wet would time down then back up so is sensing the dampness of the cloths. Is important that cloths must touch the sensor in the front. So dry properly also too large of loads will restrict air circulation and affect drying. Timed dry cloths do not need to touch sensor. Rely on temp setting. Unit is operating as should. Please fill out tech satisfaction suevey. Thank You.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KBS1
Near Cañon City, CO 81212
James
Job Details: 11/13/2024
Installed ordered parts tested ops all ckok left litmus
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Rio Rancho, NM 87124
Joe
Job Details: 11/13/2024
"Cx complaint, lid coming apart. Inspected washer and found glue coming loose that holds glass to frame of lid. Unit working as designed the way it is. Talked to trade care and was told this is cosmetic and not covered. Advised to have cx call customer service if they had any questions Sr 7740301179"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Estancia, NM 87016
Jason
Job Details: 11/13/2024
Installed part ran a quick cycle to test opperation. unit opperation checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Rio Rancho, NM 87124
Joe
Job Details: 11/13/2024
"Cx complaint, not washing dishes. Inspected unit, found wash pump not working. Replaced sump assembly. Tested unit in diagnostics and quick wash. Wash motor working fine. Unit good to go. Cx didn't have copy of receipt Advised cx about survey"
We serviced a
MAYTAG DRYER
Model MED6200KW1
Near Albuquerque, NM 87106
Jason
Job Details: 11/13/2024
Installed parts unit opperation checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Los Lunas, NM 87031
Larry
Job Details: 11/13/2024
"CX complaint - Not washing - Inspected unit and found the wash motor failed - Replaced with pre-id part, ran test cycle and tested good - Unit is operating as designed"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM11
Near Albuquerque, NM 87122
Jason
Job Details: 11/13/2024
Checked unit could verify cx cxomplaint at this time. cx said sound is intermitant. they will try and record sound next time unit makes it
We serviced a
MAYTAG WASHER
Model MVWB766FW1
Near Jacksonville, OR 97530
Jeff
Job Details: 11/13/2024
Units rotor froze to stator and caught fire. Contacted tech line and sent pics they did a report and gave me a sr# 7740316281 customer will reach out to her third party
We serviced a
WHIRLPOOL WASHER
Model WFW8500SR01
Near Edgewood, NM 87015
Jason
Job Details: 11/13/2024
Checked unit found hose had come off. re-secured hose unit checks ok
We serviced a
MIELE DISHWASHER
Model G2020SC
Near Colorado Springs, CO 80921
Charles
Job Details: 11/13/2024
"Unit not draining completely, clean ball check valve in sump and rerouted drain hose under sink to have high loop into disposal Service fee 159.95 paid URV3NH"
We serviced a
HISENSE FREEZER
Model FC72D6BWE
Near Colorado Springs, CO 80909
Charles
Job Details: 11/13/2024
"No cool, open winding on compressor. Will buy new. Service fee $139.95 paid autho R44H3H"
We serviced a
ELECTROLUX WALL OVEN
Model EW30EW55PSD
Near Colorado Springs, CO 80918
Jerimiah
Job Details: 11/13/2024
"Door hinges were left in close position without clips. Was able to reseat hinges with clips and reinstall door, unit check ok charged service call $139.95 CC Auth# 9PL33U"
We serviced a
BOSCH DISHWASHER
Model SHE55M05UC/50
Near Peyton, CO 80831
Charles
Job Details: 11/13/2024
"Install console, customer had partService fee $149.95Labor $179.95MPS $14.50Total $344.40 paid check#5840 autho 3XNNV9"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Peyton, CO 80831
Charles
Job Details: 11/13/2024
Defrost ice room and Install ice maker service kit and ice bucket
We serviced a
SAMSUNG DRYER
Model DVE55CG7100WA3
Near Fountain, CO 80817
Brandon
Job Details: 11/13/2024
Replaced heater assembly and tested op all checks ok
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Peyton, CO 80831
Mathew
Job Details: 11/13/2024
Found obstruction in fan assy. Uninstalled microwave and removed fan obstruction. Test op all okay.
We serviced a
SAMSUNG RANGE
Model NSG6DG8500SRAA
Near Peyton, CO 80831
Mathew
Job Details: 11/13/2024
"Found ignition coil burned out, no continuity. Replaced faulty ignition coil test op all okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF31CG7400SRAA
Near Colorado Springs, CO 80923
Mathew
Job Details: 11/13/2024
"Found leak at lokring connector. Sealed lokring connection, pulled vac, charged to spec. Let unit run for 20 min. Monitor temps and pressure. Checked all connections with bubble solution. All okay."
We serviced a
MAYTAG WASHER
Model MHW7000AG2
Near Colorado Springs, CO 80908
Aaron
Job Details: 11/13/2024
"F3E1F8E3 error codes upon arrival, took apart pump and found plastic piece in assembly , verified no debris between Inner and outer tub, tested unit through drain and spin cycle, working well now. Auth $139.95 #449A3U"
We serviced a
FRIGIDAIRE DISHWASHER
Model FFID2426TS4A
Near Colorado Springs, CO 80921
David
Job Details: 11/13/2024
Replaced console and switch assembly. Tested and is operating correctly.
We serviced a
SAMSUNG REFRIGERATOR
Model RFG297AAWP
Near Monument, CO 80132
Dvante
Job Details: 11/13/2024
Checked unit. Look inside and tested the evaporator fan motor. Tested ok. Did diagnostic test. No error codes. Checked filter and ice maker. All tested ok. Items are cooling properly with no issues. Unit working as designed.$139.95 CK Auth# 3W9C3V30 day Service FeeNo parts Customer only paid for service fee
We serviced a
BOSCH DISHWASHER
Model SHPM88Z75N/01
Near Penrose, CO 81240
James
Job Details: 11/13/2024
Found unit needing to be leveled and filter cleaned. Collected 159.95
We serviced a
BOSCH REFRIGERATOR
Model B36CT80SNS/04
Near Colorado Springs, CO 80906
Ralph
Job Details: 11/13/2024
"unit had a frozen fill tube, checked ohm reading on the fill tube heater and unit checked okay, cleared and unit filled cust to monitor..,.autho no. J4L943"
We serviced a
GE COOKTOP
Model JGP5036SL2SS
Near Peyton, CO 80831
Jerimiah
Job Details: 11/13/2024
Front right burner 173 marking. Found all burners and regulator still set to NG. Found the conversion kit and swapped all infected components over to LP. Unit check ok.WB28X29861 high altitude LP kit LEFT F 91LEFT R 91Center 115 RIGHT R 66 RIGHT F 102
We serviced a
KITCHENAID REFRIGERATOR
Model KSF26C6XYY04
Near Colorado Springs, CO 80904
Charles
Job Details: 11/13/2024
"Leaking from filter head need part WPW10341545Service fee $139.95Labor $229.95MPS $14.50Part $151.08Tax 12.39Total $547.87Declined repair at this time, 30 day estimate. Paid service fee $139.95 autho M4939Y"
We serviced a
BLUESTAR RANGE
Model RNB366BSS
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 11/13/2024
Installed replacement igniter. Unit check ok charged labor as quoted $209.95 CC Auth# 3VC49F
We serviced a
JENN-AIR MICROWAVE
Model JMW3430LL03
Near Colorado Springs, CO 80921
Jerimiah
Job Details: 11/13/2024
"Installed replacement MW appl mgr. Unit check ok, customer will keep track of unit functionality and will let us know if it happens again with video."
We serviced a
JENNAIR REFRIGERATOR
Model JF42NXFXDE02
Near Monument, CO 80132
Dvante
Job Details: 11/13/2024
Check unit and saw gasket was torn. Replaced gasket. Door is shutting and sealing properly. Unit working as designed
We serviced a
KITCHENAID DISHWASHER
Model KDTE704DSS0
Near Colorado Springs, CO 80906
Ralph
Job Details: 11/13/2024
"units display not working but unit will run and wash dishes, cust not to replace parts at this time"
We serviced a
GE WASHER
Model GFW655STB0DS
Near Vail, CO 81657
Erik
Job Details: 11/13/2024
spin test: PASSout of balance load suspected - CX will testJOB COMPLETE
We serviced a
GE DRYER
Model GFD65GSPV0DS
Near Clifton, CO 81520
Sean
Job Details: 11/13/2024
"customer signed disclaerchecked unit MN/SN matchunplugged unit, removed control panel and top panel. removed front panel and drum.removed radient sensor, HI limit, inlet backup, outlet thermister, saftey thermostat and outlet thermostat. installed new radient sensor, Hi limit, inlet backup, outlet thermister, safety thermostat, and outlet thermostat, reassembled unit. ran field service tests = tested good. unit heats as designed cycles off and back on.please fill out a tech servey"
We serviced a
GE DISHWASHER
Model PDT795SYV1FS
Near Avon, CO 81620
Erik
Job Details: 11/13/2024
install conduit and test: PASSJOB COMPLETE
We serviced a
CAFE DISHWASHER
Model CDT875M5N8S5
Near Grand Junction, CO 81507
Sean
Job Details: 11/13/2024
customer signed disclamerchecked unit MN/SN match unit leeking from the front left side. dispenser was put in wrong. left door hing was taped for friction.and control was not seated correctly.pulled unit out 8' removed door and removed door panel from control. removed dispenser checked seal. dispenser seal was good. lined up and reinstalled dispencer reasembled door reattached hinges and lined up and installed control. put door back on unit. reinstalled unit into counter and secured.leveled unit. started unit and ran a express wash to test unit . door closes and sealed. dispenser openes unit tested good. all butons funtional. put leak board under unit took picture.please fill out a tech servey. tank you.found no more leaks.
We serviced a
GE REFRIGERATOR/TOP
Model GFE26JYMWFFS
Near Gypsum, CO 81637
Erik
Job Details: 11/13/2024
*NEW CONSTRUCTION*normal function - door closure was a concern to CX but ice production has proven the seal to be correct from manufacturer * see quick picsJOB COMPLETE
We serviced a
PROFILE WASHER
Model PTW600BPR1DG
Near Grand Junction, CO 81501
Sean
Job Details: 11/13/2024
customer signed disclamer.unplugged unit removed top panel and controles removed bad lid lock .installed new lid lock reassembled unit tested = unit tested good opperates as designed.please fill out a tech servey
We serviced a
MONOGRAM BI REFRIGERATOR
Model ZISB420DNkII
Near Colorado Springs, CO 80906
Ralph
Job Details: 11/13/2024
"after replacing the panel, the panel is even now but does not completly sit flush on the hinges but is even, took pics and added to the ticket, unit checked okay. cust was not home on the day of the service and neighbor did not want to sign for the job"
We serviced a
MIDEA WASHER
Model MLH52S7AGS
Near Colorado Springs, CO 80920
Dvante
Job Details: 11/13/2024
Checked unit. Unit had E50 error code. Tested the inverter and motor. Both are faulty. Got the inverter motor kit from the office. Came back and replaced both parts. Tested unit and unit is working as designed.$753.10 CC Auth# 9KHCVRCustomer paid full amountNo parts returned 1 year warranty ; used 1 WMDAKIT ( Inverter Motor Kit) from stock
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AF4
Near Manitou Springs, CO 80829
Ralph
Job Details: 11/13/2024
installed listed parts and unit checked okay
We serviced a
BOSCH DISHWASHER
Model shu33a06uc
Near Colorado Springs, CO 80906
Ralph
Job Details: 11/13/2024
"unit had some burnt wires, repaired wires and replaced wire nuts and unit checked okay...autho no. TTHE4J"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Albuquerque, NM 87122
Jason
Job Details: 11/13/2024
Checked unit found ui is bad. Got unit to reset for now cx wants to see if unit acts up againSC$139.95MPS$17.50LABOR$189.95ui control#W11664671$267CC AUTHO#9NWACJ$151.85TX$52.22TOTAL$666.62
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R6241SR/AA
Near Woodland Park, CO 80863
Brandon
Job Details: 11/13/2024
"Replaced compressor, die dryer, vacuumed and charged unit to spec 70 g hass oqc passed"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS0
Near Colorado Springs, CO 80924
Aaron
Job Details: 11/13/2024
"Unit is not powering on, standing water in tub, correct power to junction box, control board is not receiving power. Needs main harness assembly. Unable to to test control, UI control or circulation motor, heater shows 13.9ohms with thermostat checking okay. Harness w11677715 $186.20Tax $15.27Supplies $14.50Hc $139.95Labor $229.95Total job $585.8730 day estimate No return on parts Auth $139.95 hc #93VUH9"
We serviced a
THERMADOR DISHWASHER
Model DWHD770CFM/22
Near Colorado Springs, CO 80919
Charles
Job Details: 11/13/2024
"Not heating, ohm heat pump, no power from module Replaced control module"
We serviced a
BEKO DISHWASHER
Model DDT38532X
Near Cañon City, CO 81212
James
Job Details: 11/13/2024
"Found kickplate misaligned, secured, no hot water to sink could not fully test"
We serviced a
MAYTAG RANGE
Model MER7700LZ2
Near Colorado Springs, CO 80925
Carlos
Job Details: 11/13/2024
Installed switches runs ok
We serviced a
WHIRLPOOL DRYER
Model WED5605MW
Near Gypsum, CO 81637
Antonio
Job Details: 11/13/2024
Installed new element and cut off ran a cycle for proper operation and unit tested good
We serviced a
SAMSUNG RANGE
Model NE63A6511SS
Near Fountain, CO 80817
Brandon
Job Details: 11/13/2024
"Replaced power cord, harness and terminal block, tested all functions all checks ok"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Redmond, OR 97756
Austin
Job Details: 11/13/2024
Installed parts ordered tested unit. All ops sat per factory spec.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Colorado Springs, CO 80925
Brandon
Job Details: 11/13/2024
Replaced ice maker and Ice route and tested op all checks ok
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW2
Near Grants Pass, OR 97527
Jeff
Job Details: 11/12/2024
Replaced valve tested machine working as should
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Redmond, OR 97756
Austin
Job Details: 11/12/2024
Installed parts ordered. Tested unit all ops sat per factory spec.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Selma, OR 97538
Jeff
Job Details: 11/12/2024
Installed parts tested machine working as should
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Grants Pass, OR 97527
Jeff
Job Details: 11/12/2024
Installed top display tested machine working as should
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Bend, OR 97702
Levi
Job Details: 11/12/2024
"Replaced listed parts, tested, all checks okay. Ensures all wires and harness is tight as possible so if unit goes off balance again, it should not effect wires"
We serviced a
KITCHENAID RANGE HOOD
Model KVWB600DSS4
Near Colorado Springs, CO 80916
Jerimiah
Job Details: 11/12/2024
"Installed replacement components, found control power board burned out, shorted against cavity due to sub par mounting pushpins. unit check ok. UI was not needed for this repair."
We serviced a
JENN-AIR MICROWAVE
Model JMW2430IL03
Near Colorado Springs, CO 80927
Aaron
Job Details: 11/12/2024
"Inspected unit, found loose connection on common wire in junction box, other lines are secure, common wire requires electrician to correct, discussed situation with techline SR7740305090 and safety team. Advised customer of situation and survey."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Colorado Springs, CO 80907
Carlos
Job Details: 11/12/2024
"Installed spray arm, original was not placed properly after unit was installed (per cx), all ok"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS2
Near Colorado Springs, CO 80908
Aaron
Job Details: 11/12/2024
"Right door suspension spring disengaged and came apart, removed and replaced hinges, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM08
Near Colorado Springs, CO 80920
Dvante
Job Details: 11/12/2024
"Replaced the diffuser, thermistor, fan motor, blade and control box. Tested unit. No loud and intermittent noises coming from the unit. Unit working as designed"
We serviced a
WHIRLPOOL FREEZER
Model WZF34X20DW05
Near Lake George, CO 80827
David
Job Details: 11/12/2024
"Replaced compressor, evacuated and charged system. Unit is cooling down."
We serviced a
KITCHENAID COMPACTOR
Model KTTS505ESS2
Near Divide, CO 80814
David
Job Details: 11/12/2024
"Replaced bin, rollers, and pedal. Working much better."
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Colorado Springs, CO 80903
Carlos
Job Details: 11/12/2024
Installed control board all ok.
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Colorado Springs, CO 80922
Aaron
Job Details: 11/12/2024
"F0E9 off balance error code upon arrival, actuator arm is not properly engaging, corrected and tested unit through diagnostic cycle, working well now. Customer also concerned about drain and spin cycle adding water to cycle, discussed situation with techline, verified normal operation . Advised customer of situation and survey. SR7740307179"
We serviced a
MAYTAG REFRIGERATOR
Model MFI2570FEZ13
Near Pueblo West, CO 81007
James
Job Details: 11/12/2024
Installed ordered/pre-ordered parts tested ops all ckok
We serviced a
KITCHENAID WALL OVEN
Model KOSE500EBS03
Near Colorado Springs, CO 80906
Carlos
Job Details: 11/12/2024
"Installed control board, sensor and element ran test heats ok maintains temp."
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS1
Near Colorado Springs, CO 80903
Carlos
Job Details: 11/12/2024
"Installed sump assembly, drain pump and valve all ok, left leak strip"
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Colorado Springs, CO 80908
Aaron
Job Details: 11/12/2024
"F7E9 locked rotor F0E5 unbalanced load error codes upon arrival, inspected rotor, hand towel binding rotor, corrected and tested, working well now, unit is level, minimal inner and outer tub movement, discussed situation with techline, suspension is not recommended. Advised customer of situation and survey. SR7740310756"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Rio Rancho, NM 87124
Joe
Job Details: 11/12/2024
"Cx complaint, fresh food section getting too cold. Replaced control ordered last visit. Tested to make sure lights, compressor, fans and dispenser were working. Unit good to go"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Santa Fe, NM 87507
Jason
Job Details: 11/12/2024
Installed control ran quick cycle unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ02
Near Rio Rancho, NM 87124
Joe
Job Details: 11/12/2024
"Cx complaint, Dishwasher not heating. Installed control and heater ordered last visit. Tested unit in diagnostic mode. Unit getting hot. Unit good to goAdvised cx about survey"
We serviced a
AMANA REFRIGERATOR
Model ART308FFDB11
Near Santa Fe, NM 87508
Jason
Job Details: 11/12/2024
Installed fan motor and sealed all gaps unit checks ok
We serviced a
MAYTAG DISHWASHER
Model WDT730HAMZ1
Near Albuquerque, NM 87120
Larry
Job Details: 11/12/2024
"CX complaint - Not draining - inspected unit and found harness loose to the drain pump - Secured harness, ran test cycle and tested good - Unit is operating as designed"
We serviced a
ASKO WASHER/DRYER COM
Model T754CW
Near Colorado Springs, CO 80922
Charles
Job Details: 11/12/2024
"No light/ no display, voltage into control. Need part 416515Service fee $159.95Labor $219.95MPS $14.50Part $725.00Tax $59.45Total $1178.85Declined estimate at this time. Paid 159.95 check#7471 autho LNUW34"
We serviced a
MAYTAG DRYER
Model MEDX655DW1
Near Albuquerque, NM 87107
Larry
Job Details: 11/12/2024
"Installed timer, ran cycle and tested good - Unit is good to go - Advised CX to have the vents cleaned proffesionally"
We serviced a
AMANA RANGE
Model AEP222VAW2
Near Albuquerque, NM 87114
Joe
Job Details: 11/12/2024
"Cx complaint, oven not working. Installed terminal block , screws and nuts. Tested burners and oven. All working good. Unit good to go"
We serviced a
WHIRLPOOL WASHER
Model CET9000GQ2
Near Colorado Springs, CO 80903
Carlos
Job Details: 11/12/2024
"Installed control board old control board has burns in motor coms pics uploaded . Unit has insufficient power coming from outlet, need to reset breaker or contact electrician."