We serviced a
LIEBHERR REFRIGERATOR BOT
Model HCB 2062
Near Colorado Springs, CO 80906
Roman
Job Details:
05/06/2024
Left hand door handle came off. Removed the panel and put the handle back on. Tightened the screws. Sc $149.95Labor 50.00Total cost $199.95Paid cc $199.95 CC Auth# C9E493; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Pueblo, CO 81005
James
Job Details:
05/06/2024
Found until with nozzle loose causing more water to enter unit then designed secured and tested. All ops test good
We serviced a
KITCHENAID RANGE
Model KSEG950ESS1
Near Albuquerque, NM 87114
Joe
Job Details:
05/06/2024
Cx complaint console won't work. Inspected unit. Needs console and control. Customer declined service
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS04
Near Rio Rancho, NM 87124
Joe
Job Details:
05/06/2024
Cx complaint. Not cooling. Replaced control ordered last visit. Tested unit.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ11
Near Monument, CO 80132
Eric
Job Details:
05/06/2024
"Found rails binding replaced, freezer door opens smoothly. Tilted unit and verified base pan. Did not change base plate as fan noise has no longer happened since last visit as customer stated. Customer will monitor and report if it returns."
We serviced a
ROPER DRYER
Model RGD4516FW0
Near Pueblo, CO 81004
James
Job Details:
05/06/2024
Installed ordered part. Tested ops all ckok advised cust to have licensed vent cleaning service to address slight restriction
We serviced a
THERMADOR RANGE
Model PRG486WDG/06
Near Edwards, CO 81632
Erik
Job Details:
05/06/2024
xlo burners working as designed - timed restarts are to be expected when turning the knobs to LO or XLOcheck voltage to burners: GOOD - no action requiredJOB COMPLETECX is aware of XLO feature/ CX not available for signature
We serviced a
GE WASHER
Model GFW650SPN0SN
Near Gypsum, CO 81637
Erik
Job Details:
05/06/2024
install part/ connect to smartHQ service:perform load test on new part: PASS * see quick picsapply firmware update - test: GOODCX not available for signatureJOB COMPLETE
We serviced a
KITCHENAID REFRIGERATOR
Model KBFS22EWMS7
Near Los Lunas, NM 87031
Larry
Job Details:
05/03/2024
CX complaint - Ive forming on bottom of freezer - Inspected unit and found the drain in back was colgged causing ice to build up during defrost - Cleared ice and drain - Unit is good to go - PIF-Auth-99HC3H
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Los Lunas, NM 87031
Larry
Job Details:
05/03/2024
Installed Im and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS3
Near Colorado Springs, CO 80924
Aaron
Job Details:
05/03/2024
"Heating element and thermostat are shorted out, removed and replaced components, tested unit through diagnostics and verified power to heating element, working well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID WALLOVEN
Model KODE300ESS21
Near Colorado Springs, CO 80924
Aaron
Job Details:
05/03/2024
"Oven door gasket is coming apart, removed and replaced gasket, working well now. Verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL RANGE
Model WGG745S0FS02
Near Colorado Springs, CO 80908
Aaron
Job Details:
05/03/2024
"Both cavity bake ignitor are shorted out, removed and replaced components, tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Frisco, CO 80443
Erik
Job Details:
05/03/2024
hose drain inlet WH41X10280 was NOT attached to tub *see quick picsreattach hose and test: GOOD(no leak) JOB COMPLETEextensive damage to lower level doors/ door frames/ door jams *see quick picscall GE TAG: report damage caused by drain hose inlet malfunction case#12940735CX aware and not available for signature
We serviced a
SAMSUNG MICRWAVE
Model MC17T8000CG/AA
Near Colorado Springs, CO 80925
Mathew
Job Details:
05/03/2024
"Replace broken fan, motor and housing. Test op all okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAEWWAA
Near Fountain, CO 80817
Mathew
Job Details:
05/03/2024
"Found ice room frozen, thawed and dried room, sealed ice room. Installed y clips and retainer. Replaced control. Test op all okay."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Colorado Springs, CO 80921
Aaron
Job Details:
05/03/2024
"Heating element connection loose, corrected and tested, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HDEDBSR/AA
Near Manitou Springs, CO 80829
Mathew
Job Details:
05/03/2024
"Found ice room frozen, defrosted room. Replaced icemaker, installed ice maker service kit, sealed room. Replaced control. Test op all okay."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Pueblo West, CO 81007
Ralph
Job Details:
05/03/2024
installed parts and unit checked okay
We serviced a
GE FREEZER
Model FUF14DLRDWW
Near Breckenridge, CO 80424
Erik
Job Details:
05/03/2024
install final union - charge unitholding pressure and cooling resumes after 10 min of chargingJOB COMPLETECX not available for signature
We serviced a
AMANA REFRIGERATOR
Model ASD2624HES
Near Colorado Springs, CO 80905
Carlos
Job Details:
05/03/2024
"Installed defrost heater and thermostat, Cx will observe. Cx paid Labor"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Colorado Springs, CO 80906
Carlos
Job Details:
05/03/2024
"Installed blower, kit and motor all ok"
We serviced a
MAYTAG RANGE
Model MER8700DS1
Near Fountain, CO 80817
Carlos
Job Details:
05/03/2024
"Installed pan, broil and bake ran test all ok. Cx paid Labor $189.95 CC Auth# 9VCFC9"
We serviced a
AMANA DRYER
Model NED4655EW1
Near Black Forest, CO 80908
Carlos
Job Details:
05/03/2024
"Ran test, issue lies in wall outlet. Only has 120VAC needs an electrician to repair outlet."
We serviced a
SAMSUNG DRYER
Model DVES2N17750W/A3
Near Pueblo West, CO 81007
Domingo
Job Details:
05/03/2024
Check support rollers and they are bad needs themSC 129.95Needs rollers but customer decided that he wanted to buy a new one so just charge for Service call customer paid $129.95
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FMDM10
Near Black Forest, CO 80908
Carlos
Job Details:
05/03/2024
Unclogged the fill tub for ice maker all ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF736SDAM11
Near Colorado Springs, CO 80922
Aaron
Job Details:
05/03/2024
"FC evaporator fan motor bearings are worn and loud, unit is cooling well at time of inspection, cleared hair from condenser, needs evaporator fan motor. Approved onsite. Removed and replaced component, working well now. Needs time to cool. Evap fan motor wpw10514110 $314.22Tax $25.77Supplies $14.50Hc $149.95Labor $209.95Total job $714.39 No return on partsPaid cash total job $714.49"
We serviced a
AMANA RANGE
Model AGR6303MMW0
Near Ordway, CO 81063
James
Job Details:
05/03/2024
Complaint of unit tripping breaker on initial pkyg in. Could not test unit fully due to no gas hookups. Did test entire electrical system no ground shorts or unusual Amp draw readings. All readings normal.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Rocky Ford, CO 81067
James
Job Details:
05/03/2024
Found loose wire at drain pump causing no drain secured wire and tested all ops test good. Left litmus.
We serviced a
PROFILE WASHER
Model PTW700BPT0DG
Near Leadville, CO 80461
Antonio
Job Details:
05/03/2024
Installed acu call rech line to program could not test properly sence unit is sitting out side on deck
We serviced a
SAMSUNG RANGE
Model NX58H5600SS
Near Colorado Springs, CO 80905
Mathew
Job Details:
05/03/2024
Replaced broken igniter. Test op all okay.
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW012
Near Rio Rancho, NM 87124
Joe
Job Details:
05/03/2024
"Cx complaint. Lights dim when washer is in agitation. Replaced clutch, rotor and stator ordered last visit. Checked unit and got same amp range. Talked to tech support. Sr# 7739018351. Per tech support, owners manual states washer should be on a dedicated circuit. Washer working as designed"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS05
Near Monument, CO 80132
Eric
Job Details:
05/03/2024
Replaced failed ice maker and tested via diagnostics. Unit now working properly. Informed customer of survey.
We serviced a
MAYTAG WASHER
Model MVWB850YW0
Near Colorado Springs, CO 80920
Roman
Job Details:
05/03/2024
Removed the old dispenser and installed new one. Tested the washer and no more leaks. Washer working great. Paid labor check $169.95 CK Auth# KXR3F9
We serviced a
ASKO DISHWASHER
Model DF1664
Near Colorado Springs, CO 80921
Roman
Job Details:
05/03/2024
Tried testing the dw but the door is damaged on the left side hinge. Screw is missing and looks like the side panel wher the acre sits is broken. Cx did not want to put too much more money into the unit. I put in a a large long screw to hold it in-place. Adjusted the led to sit properly and not on the ground. Tested the unit and the door is opening and closing properly. Checked for leaks. Dw working great. Labor $220.00Sc $149.95Total cost $ 369.95$369.95 CC Auth# 399MV3
We serviced a
WHIRLPOOL WASHER
Model MVWP575GW0
Near Colorado Springs, CO 80919
Eric
Job Details:
05/03/2024
"Found securing bolt pulled out, reinstalled and tightened down. This bolt has worked its way loose and will happen again, informed customer and she is aware that this will happen since washer needs a new agitator, also informed customer that because we are not putting in a new one we will not be coming back to repair this issue again for free."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Colorado Springs, CO 80918
David
Job Details:
05/03/2024
"Replaced UI and freezer bin. Tested operation, all working as expected."
We serviced a
GE DRYER
Model GFT14ESSM0WW
Near Colorado Springs, CO 80907
David
Job Details:
05/03/2024
"Replaced heater assembly, tested and is heating up good."
We serviced a
HOTPOINT WASHER
Model HTW240ASK6WS
Near Colorado Springs, CO 80922
David
Job Details:
05/03/2024
"Replaced gear case, pully, clutch, belt, and suspension rods. Ran test cycle, all running good."
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Belen, NM 87002
Larry
Job Details:
05/03/2024
Installed valve and tested good - Unit is good to go
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Albuquerque, NM 87111
Jason
Job Details:
05/03/2024
installed module kit
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Albuquerque, NM 87122
Jason
Job Details:
05/03/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW5100HW3
Near Albuquerque, NM 87106
Jason
Job Details:
05/03/2024
installed valve unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Albuquerque, NM 87123
Jason
Job Details:
05/03/2024
nstalled parts unit checks ok
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Edgewood, NM 87015
Jason
Job Details:
05/03/2024
Installed parts listed unit checks ok
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ1
Near Grand Junction, CO 81506
James R
Job Details:
05/03/2024
"customer sighned disclaimer . left hand adjuster damaged , another had to ordered in .replace docking retainers and adjusters on second and third shelves, run unit to verify operation. install leak board . all good . job complete.please fill out whirlpool tech satisfaction survey.Thank You."
We serviced a
WHIRLPOOL WASHER
Model MVW7230HW1
Near Fruita, CO 81521
James R
Job Details:
05/03/2024
Customer signed disclaimer. Rubbed finger on edge of tub there is some white powder residue. Put on a quick wash. No soap in dispenser. Let fill then agitate soap suds started to form. Light not heavy. Cusomer needs to do a cleaning of unit with Affresh at least once a month. Depends on usage. Also be mindful of how much soap is being used too much wilol cause the residue. They have no wtr sofener. Also put pods in the unit first before cloths. Called tech line to confirm recommedations. SR# 7739019782 Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Fruita, CO 81521
James R
Job Details:
05/03/2024
cusdtomer did sighn disclaimer.replaced gear case and rotor.run unit through diagnostic cycle.no error codes present.all good job complete. It is normal for these units to make a thumping noise due to the drain tube moving during spin. unbalanced load is often a larg contributeing factor for noise. Will also hear some noise just due to the normal vibration of the unit. please fill out whirlpool tech satisfaction survey.Thank You.
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Colorado Springs, CO 80919
Jerimiah
Job Details:
05/03/2024
"Installed replacement parts, found TCO and TCO wires melted on top back of mw. Repaired. Microwave heats food, but some reason pops a bag of popcorn in cycled. It pops, then stops and deflates, started heating again then deflates. Called techline said popcorn may not have enough moisture causing mag to overheat and inverter to lose lower, recommended to add a cup of water to mw to facilitate humidity. Unit check ok."
We serviced a
WHIRLPOOL RANGE
Model WEG515S0LS1
Near Pueblo, CO 81008
Domingo
Job Details:
05/03/2024
Call tech line 7739023571 they said needs dsi board W10898291Sc 129.95Labor$190.00Parts $309.78Msrp 14.50Total 655.14 Customer just wants to think about it just charging 129.95
We serviced a
PROFILE MICRO DRAWER
Model PVM9005FM1DS
Near Colorado Springs, CO 80907
Jerimiah
Job Details:
05/03/2024
"Door harness broke, causing door controller to be dead, door assy needs replacing. Cust hold off. Charging service call chk # 4896, labor would be $189.95WB56X30621 door assy $358.63"
We serviced a
SUBZERO REFRIGERATOR
Model 561F
Near Colorado Springs, CO 80906
Ralph
Job Details:
05/03/2024
replaced light switch and unitnchecked okay...autho no. 49C3H3
We serviced a
FRIGIDAIRE RANGE
Model PLCF489CCD
Near Colorado Springs, CO 80918
Jerimiah
Job Details:
05/03/2024
"Installed replacement control board, unit check ok, charged labor $219.95 $259.95 CC Auth# 4W3YPC"
We serviced a
JENNAIR REFRIGERATOR
Model JS42SEDUDW20
Near Colorado Springs, CO 80906
Ralph
Job Details:
05/03/2024
"door was having closing due to gthe hose and harness, remedied the issue cust to monoitor"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAZ0I
Near Leadville, CO 80461
Antonio
Job Details:
05/03/2024
Installed heater and tstat unitvtested good Lb $189.95 $189.98 CC Auth# KH4KTJ
We serviced a
MIELE COFFEE MACHINE
Model CVA7840
Near Colorado Springs, CO 80916
Ralph
Job Details:
05/03/2024
"units door would close due to the milk spout, was able to get it to recede and now the door closes correctly"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Pueblo, CO 81001
James
Job Details:
05/03/2024
Found suspension out of bracket causing noise while running and poor performance. Secured suspension and tested. All ops test good.
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5300SRAA
Near Colorado Springs, CO 80909
Brandon
Job Details:
05/03/2024
"Found leak at lokring, replaced filter and repaired leak, vacuumed unit/held vacuum for 10 minutes charged unit to spec 86g, all checks ok hass oqc passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RS28A500ASR/AA
Near Colorado Springs, CO 80909
Brandon
Job Details:
05/03/2024
"Drawers are ok replaced shelf and tested op all checks, hass oqc passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF263TEAESG/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
05/03/2024
"No errors, vent for pantry air flow was clogged with ice, cleared all ice and checked damper op all ok, fan working, drains cleared, Svf paid $129.95 Auth# MW3333"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
05/03/2024
"No errors, no ice buildup unit is making ice intermittently, replaced ice maker and cycled, all checks ok"
We serviced a
MIELE DISHWASHER
Model G5058 SCVISFP
Near Colorado Springs, CO 80918
Eric
Job Details:
05/03/2024
Removed dented panel and replaced. Unit working properly at this time.
We serviced a
MAYTAG WASHER
Model MVW7232HC2
Near Rio Rancho, NM 87144
Joe
Job Details:
05/03/2024
Cx complaint. Washer won't fill enough. Replaced drawer and control ordered last visit. Recalibrate unit. Tested unit. Unit good to go
We serviced a
SUBZERO REFRIGERATOR
Model IC-24FI-LH
Near Colorado Springs, CO 80906
Roman
Job Details:
05/03/2024
Installed new arm on the ice maker and turned it on. Ice maker started working. Made sure fridge is working properly and showed cx how and where to replace the water filters
We serviced a
GE DISHWASHER
Model DDT700SSN8SS
Near Silverthorne, CO 80498
Erik
Job Details:
05/03/2024
install MCB and heaterconnect to smartHQ service: TEST heater /fill test: successdrain/ wash test : successJOB COMPLETE
We serviced a
KITCHENAID RANGE
Model KFGC506JSS05
Near Rio Rancho, NM 87124
Larry
Job Details:
05/03/2024
Helped Joe
We serviced a
SCOTSMAN ICE MACHINE
Model SCCP30MA-1SU
Near Colorado Springs, CO 80906
Eric
Job Details:
05/02/2024
"Checked ice machine upon arrival customer stated it was overfilling, customer provided picture of overfilling, upon arrival moved ice out of the way which activated bin switch, unit no longer making ice until bin is empty. Customer to monitor if event occurs again, adjusted legs so that ice would fall more towards the back than the front."
We serviced a
THERMADOR DOUBLE WALL OVEN
Model SEMW302BS/03
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
05/02/2024
Installed replacement cooling blower. Unit check ok. Charged labor as quoted $249.95 CC Auth# P344YM
We serviced a
MAYTAG DRYER
Model MDET336AYW
Near Colorado Springs, CO 80919
Eric
Job Details:
05/02/2024
Replaced failed timer and heating element. Tested and working properly at this time.
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Peyton, CO 80831
Aaron
Job Details:
05/02/2024
"Removed and replaced suspension dampers, tested unit through a drain and spin cycle using 4 towels, unit moving, discussed situation with techline, larger loads are recommended for weight transfer, along with weight in pedestal drawer, unit is not walking without any items in the tub, little to no tub movement. Advised customer of situation and survey. SR7739015514"
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Colorado Springs, CO 80920
Eric
Job Details:
05/02/2024
"Replaced failed parts and tested, dishwasher working properly at this time. Informed customer of survey."
We serviced a
KITCHENAID M/W OTR
Model KMBS104ESS03
Near Pueblo, CO 81001
Domingo
Job Details:
05/02/2024
Unit not heating is a wall in microwave needed dolly. The high side is failing so it needs Magnetron W11409822 $267.64Thermostat magnetron WP4375079 $82.50SC 149.95Labor $200Msrp 14.50 Total $714.59 customer wants to think about it collecting service all 149.95 paid 149.95
We serviced a
SAMSUNG RANGE
Model NE63T8511S
Near Pueblo, CO 81008
Domingo
Job Details:
05/02/2024
Check out burners and everything is working customer was confused she had it on wrong settings educated customer how it works
We serviced a
BOSCH DRYER
Model WTG86403UC/19`
Near Colorado Springs, CO 80911
Roman
Job Details:
05/02/2024
Ran the dryer and it is heating up very well. Noticed the drain hose being very far down and sitting in water. Evaporator is clean and so is the lint trap. Moved the vent hose up from where it was sitting. Called tech support and they said that the dryer will take up to 2 hours on most cycles to dry. Cx can adjust the dryness level and time. Cx should never close the bathroom door to let the dryer circulate. Otherwise dryer is working the way it is supposed too.
We serviced a
SAMSUNG WASHER
Model WA55A7300AE/US
Near Colorado Springs, CO 80920
Brandon
Job Details:
05/02/2024
"Bad motor, replaced motor assy, tested op all checks ok"
We serviced a
SAMSUNG DRYER
Model DV42H5200EP/A3
Near Colorado Springs, CO 80908
Brandon
Job Details:
05/02/2024
"Bad heating element, replaced heater assembly and tested op all checks ok, Paid in full $630.06 Auth# 9LY9WU, Dc97-14486a $282.50, Labor $179.95,Svf $129.95, Mps $14.50, Tax $23.17"
We serviced a
SAMSUNG REFRIGERATOR
Model RF24R7201SR/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
05/02/2024
"Unit has had ice maker parts and other parts replaced multiple times and same issue, water tray that guides water into the ice maker is bent so when water fills ice maker it spills over the side forming ice on the bottom of the ice room which causes the issue, this area of the unit is not replaceable, all parts are functioning properly and unit is making ice, I do not recommend any parts"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ05
Near Colorado Springs, CO 80917
Eric
Job Details:
05/02/2024
"Found filter door popped off and filter removed, reattached door and installed filter tested and running fine. Collected HC $129.95 Auth 4RPC9T"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Albuquerque, NM 87105
Larry
Job Details:
05/02/2024
Installed motor and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MHW6000XG2
Near Pueblo, CO 81001
James
Job Details:
05/02/2024
Replaced ordered dp. Tested ops all ckok left litmus
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Pueblo, CO 81001
James
Job Details:
05/02/2024
Found dispenser hose out-of alignment causing water to not go where desired. Secured to clip and tested ops test good. Left limus
We serviced a
GE REFRIGERATOR
Model GSS25IYNXHFS
Near Granby, CO 80446
Erik
Job Details:
05/02/2024
install parts/test: FAILERR display even with bypass installedCALL GE TAG: not field repairable case# 12929022CX not available for signature
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Pueblo, CO 81001
James
Job Details:
05/02/2024
Found broken door switch in freezer. Replaces with pre-ordered part. Tested ops all ckok left litmus. No pop okd pee AR
We serviced a
VIKING OVEN
Model VGRC485-GQDSS
Near Colorado Springs, CO 80906
Roman
Job Details:
05/02/2024
Ran the left side bake and did smell some gas initially but did go away after it got to temp tried it a couple more time and gas smell went away. Checked the regulator and safety valve for any leaks at each connection with leak detector. Did not find any leaks. Regulator and safety valves are working the way they should. Cx also mentioned the thermostats arent reading correctly inside the oven. They are very dirty and corroded so oven is not getting proper temps in each side. Cx was going to t all the office and pay sc
We serviced a
KITCHENAID RANGE
Model KFGG500ESS7
Near Colorado Springs, CO 80903
Carlos
Job Details:
05/02/2024
"Ran test. Adjusted igniter placement, ran test all ok"
We serviced a
SAMSUNG DRYER
Model DVE45T6000V/A3
Near Penrose, CO 81240
Mathew
Job Details:
05/02/2024
"Found unit shutting off early. Fixed faulty motor, replace part test op all okay. Passed all tests."
We serviced a
WHIRLPOOL WALLOVEN
Model WOS92EC0AS03
Near Albuquerque, NM 87120
Larry
Job Details:
05/02/2024
Installed fuse and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW5015LW0
Near Colorado Springs, CO 80906
Carlos
Job Details:
05/02/2024
Installed cam and belt. Nut was loose wore out gear teeth. Runs ok
We serviced a
BLUESTAR VENT HOOD
Model BC-LPL36240
Near Colorado Springs, CO 80904
Roman
Job Details:
05/02/2024
Fan is adjusting from max to min speeds but is kind of loud even on low. Vent to the outside is not very far away and is angled right due to the main beams being directly behind it. Spoke with tech support and they said its working the way it should from the factory and 600 cfm was the lowest fan motor they have. Randy tech support guy/ did not have a file number
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Albuquerque, NM 87112
Jason
Job Details:
05/02/2024
Installed tub unit checks ok
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Albuquerque, NM 87113
Larry
Job Details:
05/02/2024
CX complaint - Washer making noise - CX took video and I saw there was a load of whites and the washer set to low spin - I could tell the noise was caused by the wet towels shifting in the basket - Instructed CX to adjust spin speed with different loads -Unit is operating as designed - Collected SC-Auth-4JPHM4
We serviced a
MAYTAG WASHER
Model MHW5630HC
Near Pueblo, CO 81003
Domingo
Job Details:
05/02/2024
Replaced shocks test it up test it okay
We serviced a
SAMSUNG WASHER
Model WF45M5500AZ/A5
Near Colorado Springs, CO 80924
Brandon
Job Details:
05/02/2024
"Drum is oblong, checked weights all ok, needs new drum, Svf paid $129.95 Auth# MA449P, Dc97-16086b $365, Labor $209.95,Svf $129.95, Mps $14.50, Tax $29.93"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Elbert, CO 80106
Aaron
Job Details:
05/02/2024
"FC for gasket is not properly sealing, removed and replaced gasket, needs time to set, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Elbert, CO 80106
Aaron
Job Details:
05/02/2024
"Drain pump is shorted out, removed and replaced pump, tested unit, working and draining well now, installed litmus strip, no leaks. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Albuquerque, NM 87110
Larry
Job Details:
05/02/2024
Installed UI and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Albuquerque, NM 87111
Jason
Job Details:
05/02/2024
Installed poarts unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Colorado Springs, CO 80917
Ralph
Job Details:
05/02/2024
"charge dthe unit with 150lbs of nitro nad started checkingfor leaks with soap bubbles and saw no signs of leaking, called tech support and the tech i spoe with is going to sent thecall to the upper techs to see what next steps to follow... file no. 7739014831"
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Albuquerque, NM 87111
Jason
Job Details:
05/02/2024
Installed lid lock unit checks ok
We serviced a
WOLF WALLOVEN
Model DO30F/S
Near Colorado Springs, CO 80906
Ralph
Job Details:
05/02/2024
INSTALLED PARTS AND UNIT CHECKED OKAY