We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Moriarty, NM 87035
Jason
Job Details:
05/01/2024
checked unit found drain line wasnt seated into pump housing. seated discharge line into housing and re-installed clip
We serviced a
THERMADOR WALL OVEN
Model PODMW301/01
Near Monument, CO 80132
Jerimiah
Job Details:
05/01/2024
"Installed replacement relay board, unit check ok, charged labor as quoted $209.95 CK Auth# F9Y9N4 Chk#2744"
We serviced a
BOSCH RANGE
Model HGI8056UC/03
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
05/01/2024
"Oven consistently off by 25-50 degrees, manual has no info for calibrating unit. Called techline. Calibrated unit to +25. Tested temp, unit ended up right above 350 target range. Cust will keep track of unit functionality. Charging service call. $149.95 CC Auth# A9L3T312037243 relay board $343.36"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Edwards, CO 81632
Antonio
Job Details:
05/01/2024
Installed door panel and name plate unit looks good
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS10
Near Colorado Springs, CO 80927
Aaron
Job Details:
05/01/2024
"Both door gaskets for RC are torn, replaced gaskets, need time to set, advised customer of damper motor sound, unit is working well. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MED6230HW
Near Colorado Springs, CO 80918
Eric
Job Details:
05/01/2024
"Customer complaint close coming out damp. Ran unit heated properly, upon further inspection found venting system needed adjustment, vent duck piped to 5 gallon bucket with water in it, remove duck from bucket to allow proper ventilation. Performed customer education of new unit and proper use, customer will monitor if situation happens again."
We serviced a
PROFILE RANGE
Model P2B940SEJ1SS
Near Pueblo, CO 81007
James
Job Details:
05/01/2024
Installed ordered part and replaced connected appliance sticker
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Belen, NM 87002
Larry
Job Details:
05/01/2024
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDM02
Near Belen, NM 87002
Larry
Job Details:
05/01/2024
"Cx complaint - Refrigerator is tripping breaker - Inspected unit and found the unit is only pulling 2,8 amps when it kicks on - Advised CX to have an electrician look at the home power - Unit is operating as designed"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRV986FDEM01
Near Colorado Springs, CO 80908
Aaron
Job Details:
05/01/2024
"Defrosted unit, removed and replaced components, unit needs time to cool, working well now. Advised customer of survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Colorado Springs, CO 80924
Aaron
Job Details:
05/01/2024
"Evaporator fan motor bearings are worn and loud, removed and replaced evaporator fan motor assembly, needs time to cool. Advised customer 5 star survey."
We serviced a
MAYTAG WASHER
Model MVWB835DW3
Near Colorado Springs, CO 80908
Aaron
Job Details:
05/01/2024
"User interface is shorted out, removed and replaced console assembly, tested unit, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVWB855DC4
Near Colorado Springs, CO 80908
Aaron
Job Details:
05/01/2024
"Removed and replaced components, tested unit and installed litmus strip, working well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Colorado Springs, CO 80916
Brandon
Job Details:
04/30/2024
"Error 85c, board detected voltage under 106 volts likely caused by power surge, checked voltage 122 volts, reset unit and ran hass oqc passed all other checks ok"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS00
Near Silverthorne, CO 80498
Antonio
Job Details:
04/30/2024
Installed acu ui panel and start component unit tested good
We serviced a
BEKO WALL OVEN
Model WOD30100SS
Near Colorado Springs, CO 80904
David
Job Details:
04/30/2024
Picked up extra parts
We serviced a
GE DRYER
Model GTD33EASK0WW
Near Rifle, CO 81650
Erik
Job Details:
04/30/2024
buzzing is normal function at the end of the cycles as a warning and as an idication of cycle completion - CX request removal of buzzer - remove bridge connection from start button to omitt buzzerJOB COMPLETECX not available for signature
We serviced a
JENN-AIR DISHWASHER
Model JDPSS245LX1
Near Breckenridge, CO 80424
Antonio
Job Details:
04/30/2024
Installed wash motor unit tested good
We serviced a
MAYTAG DRYER
Model MEDB835DW
Near Breckenridge, CO 80424
Antonio
Job Details:
04/30/2024
"Found belt not installed properly, so i installed belt properly unit tested good"
We serviced a
WHIRLPOOL REFRIGERATOR
Model KSC24C8EYY02
Near Colorado Springs, CO 80919
David
Job Details:
04/30/2024
"Adjusted doors for better closing, doors are not hitting each other now."
We serviced a
SAMSUNG WALLOVEN
Model NQ70T5511DS/AA
Near Colorado Springs, CO 80918
Brandon
Job Details:
04/30/2024
Replaced all parts and tested op all checks ok hass oqc failed to perform
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ09
Near Colorado Springs, CO 80922
Jerimiah
Job Details:
04/30/2024
Closing call.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS00
Near Silverthorne, CO 80498
Antonio
Job Details:
04/30/2024
Installed acu ui panel and start component unit tested good
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Peyton, CO 80831
Aaron
Job Details:
04/30/2024
"Dual water valve loud, removed and replaced, lifted front legs of unit so drawers are steady, tested ice maker through harvest cycle, working well now, installed litmus strip and advised customer of survey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Albuquerque, NM 87110
Larry
Job Details:
04/30/2024
Installed Im and tested good - Unit is good to go
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ2
Near Rio Rancho, NM 87144
Joe
Job Details:
04/30/2024
Cx complaint. Unit shakes. Replaced feet ordered last visit. Tested unit. U it good to go
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FG/AA
Near Colorado Springs, CO 80915
Mathew
Job Details:
04/30/2024
"Found intermittent power issue. Unit will need high voltage cap and diode. Cx holding off on repair for now, trying to find POP $129.95 CC Auth# 9VK4N4Svf 129.95MPs 14.50Cap 2501-001011 135.74 Diode DE59-00002A 57.70Labor 219.95"
We serviced a
AMANA WASHER
Model NFW5800HW0
Near Dillon, CO 80435
Antonio
Job Details:
04/30/2024
Called whlp cx needs to call customer service can not find leak Sr#7738056080
We serviced a
SAMSUNG REFRIGERATOR
Model RF4287HARS
Near Colorado Springs, CO 80919
Brandon
Job Details:
04/30/2024
"Replaced inverter and tested op all checks ok cx will monitor temps, Labor paid $199.95 Auth# V4444U"
We serviced a
FISHERPAYKEL DISHWASHER
Model DD24DCHTX6V2
Near Colorado Springs, CO 80911
Roman
Job Details:
04/30/2024
Dw control bord and panel taken apart. Looks like water ahoy in and corroded the touch controls. Control board under the controls also not responding with buttons. Cleaned it and got it to work once and dw acted up again. Motor in the top dw also bad. Recommend replacing the motor and control board. Cx going to look for other units. $149.95 CK Auth# KYX99V
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031US
Near Colorado Springs, CO 80925
Mathew
Job Details:
04/30/2024
"Found. Unit installed incorrectly. Side mount screws ripped out of cabinet, unit leaning forward. Pulled unit out to test, could not find any signs of components leaking. Re installed, test op all okay. $142.95 CC Auth# 944A9RCollect svf 129.95."
We serviced a
GE REFRIGERATOR
Model GFE28GYNJFS
Near Pueblo, CO 81008
Domingo
Job Details:
04/30/2024
Replace dispenser board test it test it good
We serviced a
WHIRLPOOL RANGE
Model WFE540H0AE0
Near Colorado Springs, CO 80924
Eric
Job Details:
04/30/2024
"Customer complaint that front right burner goes straight to high even in medium or medium-low, tested selector and found it shorting causing burner to work only on high or low, recommend replacing selector. Infinite switch WPW10434452 $129.24Tax$10.60Supplies$14.50Hc$129.95Labor$219.95Total$504.24 paid hc 129.95 balance 374.2930 day estimate No return on partsAuth Hc 129.95 4WE4JJ"
We serviced a
WHIRLPOOL M/W OTR
Model WML55011HS07
Near Albuquerque, NM 87109
Larry
Job Details:
04/30/2024
CX complaint - MW turned on by itself - Talking with CX and found that she was cooking on the cooktop and the MW fan came on for a long time - Explained that the unit had over heated from the cooktop burners and turned on the fan automatically - Unit is operating as designed - Called Techline to document (SR7738997232)
We serviced a
SAMSUNG DRYER
Model DVE46BB6700DA3
Near Colorado Springs, CO 80925
Mathew
Job Details:
04/30/2024
Found belt broken. Replaced belt and test op all okay.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS2
Near Florissant, CO 80816
David
Job Details:
04/30/2024
"Installed ordered parts. Ran diagnostics, all ran good."
We serviced a
MAYTAG WASHER
Model MVWP575GW1
Near Rio Rancho, NM 87144
Joe
Job Details:
04/30/2024
Cx complaint. many different intermittent issues. Installed control ordered last visit. Tested unit. Unit good to go
We serviced a
GE RANGE
Model JB968SL2SS
Near Colorado Springs, CO 80906
Roman
Job Details:
04/30/2024
Took the top off the unit and ohmed out the elements and thermostat and thermostat is damaged and not reading correctly. Element also blew out in 2 spots. Recommend replacing the element. Cx was going to talk with family before 12 element #WB30T10107 $321.22Tax $26.34Parts total $347.56MPs $14.50Labor $199.95Sc $129.95Total cost $691.96Paid sc $129.95 CC Auth# V9349T
We serviced a
MIELE WASHER
Model WWH860
Near Manitou Springs, CO 80829
Roman
Job Details:
04/30/2024
Cx has had twin dos tubes cleaned in the past and wanted it all taken apart and cleaned. Rubbed all full of detergent. Recommend cx doesnt use that system and just puts soap in the dispenser. Labor $229.95 Sc $149.95Total cost $379.90Paid total cost $379.90 CC Auth# 9NV9R3
We serviced a
DACOR DISHWASHER
Model DDW24M999US/DA
Near Colorado Springs, CO 80907
Mathew
Job Details:
04/30/2024
Replaced faulty wire harness. Test op all okay.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FPRH19D7LF1
Near Colorado Springs, CO 80906
Ralph
Job Details:
04/30/2024
UNITS DRAIN HOLE WAS CLOGGED AND CLEARED...CUST PAID TOTAL BILL AUTHO NO. A3JET4
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325FDAM01
Near Rio Rancho, NM 87124
Joe
Job Details:
04/30/2024
Cx complaint. Ice landing all over the floor. Installed ice bin and ice dispenser ordered last visit. Tested unit. Unit good to go
We serviced a
MAYTAG DRYER
Model MED6230HW1
Near Albuquerque, NM 87109
Larry
Job Details:
04/30/2024
CX complaint - Dryer starts the stops all the time - Inspected unit and found the motor failed - CX does not want to bear the cost of repair and will replace - SC paid- Auth-34XJ9R
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Manitou Springs, CO 80829
Carlos
Job Details:
04/30/2024
"Ran test, ran hard reset unit runs ok, cx had recently experience a surge with last storm, advised cx to get a surge protector. Cx asked if using heavy duty with small loads is advisable, said no, to use normal cycle or quick wash for small loads. Recommend cx use affresh tablet for cleaning washer of excess suds. As well as leaving the door open after washes to avoid any possible mold build up that might occur."
We serviced a
ASKO DRYER
Model N/A
Near Colorado Springs, CO 80904
Roman
Job Details:
04/30/2024
"Cx wanted me to run dryer and make sure its working, dryer tunes on and heats. Has a burning smell. Took off the vent hose and found lint built up. Removed it and ran dryer. Dryer didnt burn as much but recommend getting the walls cleaned. Labor 50 +89.95 + 149.95 289.90$289.90 CC Auth# is J3LT43 combined with washer ticket"
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GWH0
Near Colorado Springs, CO 80919
Carlos
Job Details:
04/30/2024
"Installed wash motor, diverter and spray arm ran test used clear door, spray arm spins normally, left leak strip all ok"
We serviced a
PROFILE WASHER
Model PFQ97HSPV0DS
Near Pueblo, CO 81005
James
Job Details:
04/30/2024
Installed previous techs ordered part. Tested ops ran hp diagnostic all temps pass no error observed. Left litmus
We serviced a
KITCHENAID WALL OVEN
Model KODE500ESS20
Near Colorado Springs, CO 80924
Jerimiah
Job Details:
04/30/2024
Trim piece to be installed was in pieces. Was able to repair and install. Unit check ok.
We serviced a
FRIGIDAIRE GAS RANGE
Model FCRG3052ASA
Near Fountain, CO 80817
Jerimiah
Job Details:
04/30/2024
"Found back right burner not igniting, found burner head clogged, repaired, unit check ok."
We serviced a
MAYTAG WASHER
Model MVW6230HC0
Near Albuquerque, NM 87120
Larry
Job Details:
04/30/2024
CX complaint - Wsher making loud screaching noise - Inspected unit and found the belt and pulley worn - Replaced with TS and tested good - Unit is good to go - CX is PIF - Auth-CC3V94
We serviced a
MAYTAG DRYER
Model MED5630HW1
Near Peyton, CO 80831
Aaron
Job Details:
04/30/2024
"Heating element is shorted out due to normal use, removed and replaced element, tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ2
Near Peyton, CO 80831
Aaron
Job Details:
04/30/2024
"Circulation motor is not effectively working, removed and replaced motor sump assembly, tested unit, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVWP576KW0
Near Peyton, CO 80831
Aaron
Job Details:
04/30/2024
"Removed and replaced inlet valve assembly, tested unit and working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, CO 80927
Aaron
Job Details:
04/30/2024
"Lid latch assembly is shorted out, removed and replaced latch, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Colorado Springs, CO 80908
Aaron
Job Details:
04/30/2024
"Removed and replaced motor and blower, tested unit, working and heating well now. Total due was previously paid."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS3
Near Colorado Springs, CO 80908
Aaron
Job Details:
04/30/2024
"Replaced roller assemblies and stops, tested unit, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Pueblo, CO 81006
Domingo
Job Details:
04/30/2024
Replace part ran diagnostic cycle and pass dish washer working correctly at this time.
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KBS1
Near Breckenridge, CO 80424
Antonio
Job Details:
04/30/2024
Found right door spring off due to catching on insulation reinstalled and made sure insulation not going to catch again unitvtested good
We serviced a
SCOTSMAN ICE MACHINE
Model DCE33PA-1SSD
Near Colorado Springs, CO 80904
Ralph
Job Details:
04/30/2024
REPLACED LITED PARTS AND UNIT CHECKED OKAY
We serviced a
GE RANGE
Model RBS330DR2WW
Near Glenwood Springs, CO 81601
Erik
Job Details:
04/30/2024
upon completion of diagnostics found unit to be fine.problem is do to hyper sensitivity of arc fault breaker. call GE TAG: CX needs to contact an electrition to have standard 30 amp breaker.job complete
We serviced a
SAMSUNG RANGE
Model NE63T8111SS/AA
Near Colorado Springs, CO 80916
Mathew
Job Details:
04/30/2024
Found burner switch installed upside down. Fixed switch and test op all okay.
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5501SG/AA
Near Peyton, CO 80831
Brandon
Job Details:
04/30/2024
"Error 39c, 41c, ice maker is broken needs replaced all other checks ok, PCB is 1199G, Svf paid $129.95 Auth# MCKHXV, Da97-15217d $189, Labor $189.95, Svf $129.95, Mps $14.50, Tax $15.50"
We serviced a
BOSCH DISHWASHER
Model SHV89PW73N/91
Near Aspen, CO 81611
Erik
Job Details:
04/30/2024
F18 error.prime softener tank to clear F18 water tap error.install water inlet and aquastop . all good job complete.
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Albuquerque, NM 87114
Joe
Job Details:
04/30/2024
Cx complaint. Dryer won't always start. Replaced control and ui ordered last visit. Tested multiple times. Unit good to go
We serviced a
MAYTAG WASHER
Model MVW7232HC2
Near Belen, NM 87002
Larry
Job Details:
04/30/2024
Installed and calibrated control and passed diagnistocs cycle - Unit is operating as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ17
Near Santa Fe, NM 87507
Jason
Job Details:
04/30/2024
sr7738997964. installed parts found molex connector wasnt seated. seated connector unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ5
Near Santa Fe, NM 87506
Jason
Job Details:
04/30/2024
Installed control unit opperation checks ok
We serviced a
SUB ZERO REFRIGERATOR
Model 661/0
Near Colorado Springs, CO 80904
Ralph
Job Details:
04/30/2024
INSTALLED LISTED PARTS AND UNIT CHECKED OKAY
We serviced a
MAYTAG WASHER TOP LOAD
Model MVWX655DWO
Near Colorado Springs, CO 80907
Roman
Job Details:
04/30/2024
"Noticed the agitator is very loose, checked the threads on the transmission and agitator disc and they are worn out. Recommend replacing the transmission and agitator disc. Tightened the nut on the disc and should hold for now as a temporary fixPaid sc"
We serviced a
MAYTAG DRYER
Model MEDB835DW
Near Breckenridge, CO 80424
Antonio
Job Details:
04/30/2024
"Found belt not installed properly, so i installed belt properly unit tested good"
We serviced a
WOLF COOKTOP
Model CG304T/S
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
04/30/2024
"Front right and rear left burners inconsistently igniting, cleaned igniter heads and adjusted igniter wire to insulate spark further up igniter. Unit check ok"
We serviced a
WHIRLPOOL WASHER
Model WFW9640XW00
Near Colorado Springs, CO 80915
Roman
Job Details:
04/30/2024
"Noticed washer has no hot water hooked up to it, ran the washer on a cold cycle and washer started filling. Ran it again and washer did not fill with water but no error code comes up. Checked the voltage to the valve and its getting 120V. Checked the drain pump and it is okay and filter is clean. Washer draining properly. Recommend replacing the inlet valve. Installed new valve and connected the hot water. Tested the u it and checked for leaks. Washer is working great. Inlet valve #WPW10247306 $191.52Tax $15.70Parts total $207.22MPs $14.50Labor $189.05Sc $129.95Total cost $541.62; used 1 WPW10247306 (Inlet valve) from stock"
We serviced a
ZLINE SINGLE WALL OVEN
Model AWS-30
Near Colorado Springs, CO 80919
Jerimiah
Job Details:
04/30/2024
"Cust having erratic temp issues, unit being too hot one cycle and too cold the next. Zline sent out a relay board and power board to remedy situation but did not send temp sensor, parts installed. Unit also having issues with time clock adding minutes. Unit needs replacement console and it problems persist with bad cooking temps, also will need thermal sensor. Cust will try unit unit out and tell zline what is needed based on tech support recommendations. Closing call"
We serviced a
BOSCH RANGE
Model HDI7282U/03
Near Colorado Springs, CO 80919
Jerimiah
Job Details:
04/30/2024
"Warming drawer not heating, getting error 33, thermal sensor short, found harness connecting sensor to board broken, needs replacement harness connector. Harness no longer available. Charging service call. $172.44 CC Auth# 39C3HC00619630 drawer sensor00657860 power board."
We serviced a
WOLF WALLOVEN
Model DO30PM/S/PH
Near Colorado Springs, CO 80908
Jerimiah
Job Details:
04/30/2024
"Installed replacement console, unit check ok. Cust will keep track of unit functionality."
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Glenwood Springs, CO 81601
James R
Job Details:
04/30/2024
"Customer signed disclaimer.Put into service diagnostics no error codes. Run thru auto test. Found a water leak at cold water hose tightened as best as could. But still leaks cannot shut cold water valve off at wall. cu7stomer will need to have repaired. Tilted unit back checked cover, pulleys and belt it is loose has been slipping will replace it. W11239857. Can see where cover has been rubbing on the floor. adjusted feet down so it doesnt and leveled unit. Also performed S.P. W11695259 to take care of vibration noise. It is important not to overload unit will cause out of balance loads and wont operate properly. Unit operating as should.; used 1 W11239857 (Belt (Washer)) from stock"
We serviced a
GE REFRIGERATOR
Model ZFSB25DTG
Near Colorado Springs, CO 80920
Eric
Job Details:
04/30/2024
"Fridge side not cooling. After inspection found RC evp fan shorted out. Upon check with parts department, evp motor no longer available, informed customer of options. No part available Tax$0Supplies$0Hc$149.95Labor$0Total$149.95Auth paid HC $149.95 TLTC33"
We serviced a
GE DRYER
Model GTD33EASK0WW
Near Gypsum, CO 81637
Erik
Job Details:
04/29/2024
install timer and test: set at 25 min/ GOODJOB COMPLETE
We serviced a
MAYTAG WASHER
Model MHW7100DCO
Near Pueblo, CO 81007
Domingo
Job Details:
04/29/2024
Reposition washer and dryer
We serviced a
MAYTAG WASHER
Model MVWB835DC5
Near Albuquerque, NM 87105
Larry
Job Details:
04/29/2024
CX complaint - Washer is making a really loud noise like grinding - Inspected unit and could not duplicate the issue - Ran diagnoatic cycle successfully - Unit is operating as drsigned
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS
Near Edwards, CO 81632
Antonio
Job Details:
04/29/2024
Unplugged ground wire heated unit to 500 degrees and then reinstall ground wire unitvtested good
We serviced a
WHIRLPOOL WALLOVEN
Model KOCE500EESS09
Near Albuquerque, NM 87120
Larry
Job Details:
04/29/2024
CX complaint - MW no working - Inspected unit and found F6E3 error - Unit needs MW appliance manager - CX does not want to bear the cost of repair - Collected SC (Auth-939FWV)Control-W11325786-$224.40Labor-$219.95MSP-$17.5Tax-$39.26
We serviced a
SAMSUNG DRYER
Model DVE50R5400V/A3
Near Fountain, CO 80817
Mathew
Job Details:
04/29/2024
Found obstruction in blower wheel housing. Vacuumed out obstruction and test op all okay. Cleared venting to wall.
We serviced a
MAYTAG WASHER
Model MAH5500BWW
Near Colorado Springs, CO 80919
Glenn
Job Details:
04/29/2024
"Bad Latch Assy, Called Techline to verify which part to order, as unsure of series model. Suggested part for Series 10. SR# 7738988385 , Latch Assy - WP22003593 $330.76 , Tax $27.12 , MPS $14.50 , Labor $179.95. Declined Estimate for now. Paid SC Fee of $89.95 + Tip $30.00 = $119.95 , Autho# L439AC"
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Albuquerque, NM 87120
Larry
Job Details:
04/29/2024
CX complaint - not washing properly - Inspected unit and found the clotch failed with the basket engaged - Replaced clutch with TS and tested good - Unit is operating as designed; used 1 W10721967 (Cam) from stock
We serviced a
HOTPOINT DRYER
Model HTX24EASK0WS
Near Colorado Springs, CO 80917
David
Job Details:
04/29/2024
"Checked dryer, found bearing dry, lubed and tested. Running good"
We serviced a
WHIRLPOOL DRYER
Model WED5605MC0
Near Edwards, CO 81632
Antonio
Job Details:
04/29/2024
Installed motor acu and blower wheel unit tested good
We serviced a
MAYTAG WASHER
Model MVW6500MW0
Near Albuquerque, NM 87120
Larry
Job Details:
04/29/2024
Installed parts listed and tested good - Unit is good to go
We serviced a
MAYTAG DRYER
Model MEDC465HW
Near Pueblo, CO 81004
Domingo
Job Details:
04/29/2024
Check the temp in the dryer on time dry and it got to 200? and it came down to 120? and then back up and I check it on sensor dry it got to 125? and thats it check the vent hose it was block I unblocked it and now its working good
We serviced a
AMANA RANGE
Model AER6303MFW5
Near Albuquerque, NM 87120
Larry
Job Details:
04/29/2024
CX complaint - Clock and lights are not working but the burners are - Inspected unit and found 240vac between L2 and Ground and nothing between L1 and Ground or between L1 and L2 - Advised CX to contact a liscensed electrician
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Colorado Springs, CO 80925
Carlos
Job Details:
04/29/2024
"Installed heating element ran test all ok, recommend cx have vents cleaned and replace hose with semi-rigid hose per owners manual."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS11
Near Colorado Springs, CO 80921
Glenn
Job Details:
04/29/2024
"Actual arrival time 11:45am, Unit making clicking noise 2-3 times a day, for about 10 minutes. Reseat connections to main PCB, Checked compressor lines and started unit about 3 times to rule out noise during compressor start. Unable to duplicate noise at this time. Suggest customer video tape to record noise during issue if it ocurrs again. All OPS Test:OK"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS03
Near Colorado Springs, CO 80911
Carlos
Job Details:
04/29/2024
"On arrival Cx explained they are concerned with temperature in freezer. I was unable to get accurate reading since unit was going through its defrost cycle, Got as low ass 10 degrees. Checked Pressures low side was -1 and high side was 145 checked for leaks with detector none found. Explained to cx to put a glass of water in their refrigerator with a thermometer and check temperature, if issue is present to call back. Installed Ice maker ran harvest cycle runs ok, cx will observe. Cx paid Labor for Ice maker Install $189.95 CC Auth# M933EV"
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GPS1
Near Colorado Springs, CO 80924
Glenn
Job Details:
04/29/2024
"Verifiy no water leaks at door, supply valve, etc, Reseat connections to PCB, Ran Diag Test 2X, Did see some suds, and suggested running clean washer product, in case issue caused by suds overdose. Also suggest run hot water at sink prior to start of cycle. All OPS Test:OK"
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, CO 80906
Carlos
Job Details:
04/29/2024
"Installed control board and Ui and moisture sensor, ran test heated to 165 degrees all ok, Cleaned moisture sensor electrodes all ok"
We serviced a
WHIRPOOL REFRIGERATOR
Model ET18NMXFW03
Near Edwards, CO 81632
Antonio
Job Details:
04/29/2024
Unit needs tstat and heater cx holding on repair but still thawed out Autho# ffe933$149.95$189.95$339.90
We serviced a
SAMSUNG REFRIGERATOR
Model RF23HCEDBSR/AA
Near Colorado Springs, CO 80915
Brandon
Job Details:
04/29/2024
"No errors, called tech support did ice maker inspection, leaking from Ice route, need new ice route per Samsung"
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Pueblo, CO 81004
Domingo
Job Details:
04/29/2024
Replaced board ran a whole cycle on quick to see if it got stuck in the 1 min spin and it got to end everything test it good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Colorado Springs, CO 80926
Carlos
Job Details:
04/29/2024
"Ran test found broken wires at bottom of door, Needs a new door cx will no repair."
We serviced a
UNKNOWN REFRIGERATOR
Model PSS26LGRAWW
Near Pueblo, CO 81001
James
Job Details:
04/29/2024
Installed ordered parts replaced cust supplied filter. tested ops all ckok. Took b&a photos