We serviced a
WOLF MICROWAVE
Model MD30TE/S
Near Colorado Springs, Colorado 80921
Ryan
Job Details:
05/09/2025
Powered unit down and reset machine all now working fine. Instructed customer on use and care. RKCustomer paid service call 159.95Auth X449NF
We serviced a
MAYTAG DRYER
Model MED8630HC2
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
05/09/2025
Installed new heating element and cleaned out unit. Tested operation and all checks ok. RK
We serviced a
CAFE REFRIGERATOR
Model CGE29DP3TBD1
Near Colorado Springs, Colorado 80921
Charles
Job Details:
05/09/2025
Customer could not remove glass shelf above drawers due to spillage. Removed glass for customer to clean. Service fee $159.95 paid autho J9K44W
We serviced a
SAMSUNG DISHWASHER
Model DW80R5060UG
Near Colorado Springs, Colorado 80916
Mathew
Job Details:
05/09/2025
"Found power off to unit. Reconnect power and test op, all okay. Cx states dog climbed into unit, breaking mounting brackets. Re installed unit$139.92 CC Auth# FHJ9U4Collect svf 139.95"
We serviced a
SHARP MICRO DRAWER
Model SMD2470ASYD
Near Colorado Springs, Colorado 80921
Jerimiah
Job Details:
05/09/2025
"Unit not heating, adjusted switches to make contact, repaired, unit check ok charged service call $160.94 CC Auth# 4WFL99"
We serviced a
THERMADOR RANGE
Model PRG486WDH/12
Near Pueblo West, Colorado 81007
James
Job Details:
05/09/2025
Found igniter wire loose causing intermittent non light. Secured and tested all ops test good.
We serviced a
THERMADOR WALL OVEN
Model POD302W/03
Near Silverthorne, Colorado 80498
Erik
Job Details:
05/09/2025
using oven dolly remove double walloven - replace upper oven cooling fan/ test: PASSJOB COMPLETE
We serviced a
BOSCH DISHWASHER
Model SHX78CM5N/25
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
05/09/2025
Removed and replaced damaged stainless door panel. All now checks ok. RK
We serviced a
SUBZERO BI REFRIGERATOR
Model 690/F
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
05/09/2025
CLEANED THE CONDENSER BUT COULDNT CREATE THE SOUND ...AUTHO NO. 9KUW9C
We serviced a
THERMADOR DISHWASHER
Model DWHD440MFP/02
Near Colorado Springs, Colorado 80921
Ryan
Job Details:
05/09/2025
Removed and replaced leaky water inlet valve.Tested operation and all now checks ok.RK
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Albuquerque, New Mexico 87113
Jason
Job Details:
05/09/2025
cInstalled compressor charged unit up. unit is cooling pressures check ok unit opperation checks ok. spoke to cx about review
We serviced a
FRIGIDAIRE RANGE
Model FGEH3047VFE
Near Colorado Springs, Colorado 80923
Jerimiah
Job Details:
05/09/2025
Installed replacement lenses. Unit check ok.
We serviced a
LG REFRIGERATOR
Model LRFOC2606S/00
Near Colorado Springs, Colorado 80908
Dvante
Job Details:
05/09/2025
"Checked unit, found the ice maker working and dispensing properly. Didnt find any error codes on display. Ice maker on door is functioning. Display is operating. No issues with unit."
We serviced a
GE DISHWASHER
Model GDP665SYN8FS
Near Colorado Springs, Colorado 80910
David
Job Details:
05/09/2025
"Replaced ordered parts, ran a cycle and diverter is going into it's different positions. Placed leak strip."
We serviced a
ZLINE RANGE
Model RG30
Near Colorado Springs, Colorado 80922
Jerimiah
Job Details:
05/09/2025
"Installed other new broil flame spreader, again, broil would not ignite. Called techline again and explained broiler function will NOT work with rework kit. Techline said they will contact Cust with other options and alternatives nc advised Cust to not use broil function. Closing call."
We serviced a
BOSCH MICROWAVE OVEN
Model HMVP053U/02
Near Terrebonne, Oregon 97760
Richard
Job Details:
05/09/2025
Installed new switch assembly cycle tested unit all tested fine at this time
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS05
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
05/08/2025
"Water housing connection is not fully engaged, corrected and tested unit, working well now, no leaks, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW1
Near Bend, Oregon 97702
Levi
Job Details:
05/08/2025
"Replaced wire harness latch and control board, tested, all checks okay"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Medford, Oregon 97504
Jeff
Job Details:
05/08/2025
Installed parts repaired one hole. Put 64 g r600
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HBS05
Near La Pine, Oregon 97739
Levi
Job Details:
05/08/2025
"Replaced single inlet valve, tested, all checks okay. Recommended to keep an eye out for leaks in case primary hose is leaking."
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near La Pine, Oregon 97739
Levi
Job Details:
05/08/2025
Adjusted stove top burner so the flame was not so high on low setting. Customer is happy now
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Eagle Point, Oregon 97524
Jeff
Job Details:
05/08/2025
Repaired wiring tested machine working as should
We serviced a
KITCHENAID RANGE
Model KFDD500ESS12
Near Manitou Springs, Colorado 80829
Jerimiah
Job Details:
05/08/2025
"Installed propane rework kit. Flames are very low still, unit properly installed, tank is set to 10psi. Suggesting to find a way to increase to at least 12psi, Cust will have to research. Told Cust we can come back out to calibrate flame size once we have the proper fuel pressure. SR#7741530793"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
05/08/2025
"Capacitor is shorted out, removed and replaced, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
KITCHENAID FREEZER
Model KRFF577KPS03
Near Colorado Springs, Colorado 80904
Charles
Job Details:
05/08/2025
Replaced board and evaporator fan motor with harness
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
05/08/2025
Installed cutoff ran test all ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Colorado Springs, Colorado 80918
Dvante
Job Details:
05/08/2025
"Checked unit, didnt find any leaks. Customer was telling me the water was building up inside due to the clogged pipe and unit not draining properly. Saw the drain hose on the disposal this time. Did replace gasket just in case. Tested unit, no leaks coming from the bottom. Unit is operating as designed."
We serviced a
WHIRLPOOL DRYER
Model WHD560CHW2
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
05/08/2025
"Installed Control Board and UI, runs ok"
We serviced a
MAYTAG WASHER
Model MVW5430MW2
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
05/08/2025
"Installed capacitor and harness, ran test and calibration runs ok"
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
05/08/2025
"Turntable motor is not operating, removed and replaced, tested unit through two one minute cooks, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
05/08/2025
Installed sump assembly ran test all ok. Recommend Cx use Rinse Aid
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS00
Near Colorado Springs, Colorado 80921
Charles
Job Details:
05/08/2025
"Still no cool, no pressure, pressurized system, no pressure loss on gages, removed gages with system pressurized, leaking from shader valve on drier. Replaced valve stem. Need to recharge. Returned and charged system."
We serviced a
MAYTAG WASHER
Model MVW7230HC1
Near New Castle, Colorado 81647
Josh
Job Details:
05/08/2025
"Customer signed disclaimer. Verified MN SN.Customer states that unit does not function. Technician was unable to perform calibration or test cycle upon last visit as unit was not installed. Technician confirmed that unit has now been installed appropriately, but is asking for factory WiFi. According to manufacturer service pointer, tech cleared WiFi warning and initiated test cycle. Unit is functioning properly within manufacturer specifications."
We serviced a
WHIRLPOOL DRYER
Model WET4027HW2
Near Granby, Colorado 80446
Antonio
Job Details:
05/08/2025
"Installed new duct, housing, and drum ran a cycle for proper operation and unit tested good Also advised cx of whlp survey"
We serviced a
WHIRLPOOL RANGE
Model KSDB900ESS6
Near Grand Lake, Colorado 80447
Antonio
Job Details:
05/08/2025
Installed new door panel unit looks great
We serviced a
MAYTAG DRYER
Model MED5630HW2
Near Carbondale, Colorado 81623
Josh
Job Details:
05/08/2025
"Customer signed disclaimer, verified MN SN POP.Customer states that unit does not properly dry clothing. Technician confirmed customer concern, unit is tumbling but not heating. Further inspection found that the thermal cutoff is toning open and needs to be replaced. Technician installed replacement TCO from truck stock and performed test cycle. Tech also realigned duct behind unit and confirmed positive exterior ventilation. Unit is functioning properly within manufacturer specifications."
We serviced a
KITCHENAID WALL OVEN
Model KOEC527PSS00
Near Grand Lake, Colorado 80447
Antonio
Job Details:
05/08/2025
Installed new motor and sensor then headed cup of water for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS10
Near Grand Lake, Colorado 80447
Antonio
Job Details:
05/08/2025
Installed new cover and slides unit tested good
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Colorado Springs, Colorado 80920
David
Job Details:
05/08/2025
"Checked washer, found drain hose clamp not attached to tub and hitting the back panel. Ran cycle much quieter."
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
05/08/2025
Adjusted shield ran cycle with a load runs ok
We serviced a
SAMSUNG DRYER
Model DVE55A7700V/A3
Near Pueblo, Colorado 81008
Domingo
Job Details:
05/08/2025
Check main power and its not getting 240 from line 1 to line 2 needs electrician charge SC 139.95
We serviced a
WHIRLPOOL WASHER
Model WFW4720RW0
Near Albuquerque, New Mexico 87120
Larry
Job Details:
05/08/2025
Instaleld UI and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Los Alamos, New Mexico 87544
Antonio
Job Details:
05/08/2025
"cx complanit - error code F7,E1 - used all parts that wre shiped to cx home - unit is working properly - survey mentioned"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Edgewood, New Mexico 87015
Jason
Job Details:
05/08/2025
Installed control ran quick cycle. unit opperation checks ok. spoke to cx about review
We serviced a
MAYTAG M/W OTR
Model MMMF6030PZ00
Near Los Lunas, New Mexico 87031
Larry
Job Details:
05/08/2025
CX complaint - MW tripping breaker - Inspected unit and found it pulling 16..4 amps - Unit is not properly installed - Advised cx to contact installed to correct for further possible diagosis
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Rifle, Colorado 81650
Sean
Job Details:
05/08/2025
Checked unit MN SN POP Customer signed disclaimer.Checked the unit out verified diagnostics.Vented ref unbraized the ref lines and removed them from compressor. Unhooked power to comp.Removed com and filter drier.Places the new compressor and filter drier and brazed them in place . Pressure checked with nitrogen. Pulled vacuum to 300 microns. Charged the unit with 1.89 oz r600.Plugged the unit back in and tested. The unit came on and started cooling. Ref levels all looked good. Unit is operating as designed by the factory.Tested good .If you appreciate the service I performed than please go online and fill out a technician survey.
We serviced a
WHIRLPOOL DRYER
Model WED9400SZ0
Near Glenwood Springs, Colorado 81601
Josh
Job Details:
05/08/2025
"Customer signed disclaimer, verified MN SN.Customer states that unit does not start or function. Technician confirmed customer concern. Unit is receiving power, however, motor is only receiving 12.89v. Further inspection found that the drive belt is also broken, and 2 drum support rollers are damaged and need to be replaced. Recommend replacement of failed user interface and control, drive belt and drum support rollers. Technician contacted manufacturer support, finding that control and user interface components are no longer available. Manufacturer support communicates that they also cannot source from anywhere, and warranty company will be reaching out to customer within 24-48hours to establish resolution. Reference number: 7741472215."
We serviced a
WHIRLPOOL RANGE
Model WFE775H0HW1
Near Belen, New Mexico 87002
Larry
Job Details:
05/08/2025
Installed element and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DRYER
Model WED4720RW0
Near Santa Fe, New Mexico 87506
Antonio
Job Details:
05/08/2025
cx complanit - dryer is resetting itself - cx said they had two power outages recently.unit is back up and running properly - survey mentioned
We serviced a
WOLF RANGE
Model DF60650DG/S/P
Near Colorado Springs, Colorado 80919
Jerimiah
Job Details:
05/08/2025
Installed dual rework kits. Unit check ok
We serviced a
WOLF COOKTOP
Model CI365TF/S
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
05/08/2025
INSTALLED LISTED PART AND UNIT CHEKCED OKAUY
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRSC503ESS01
Near Monument, Colorado 80132
Dvante
Job Details:
05/08/2025
"Checked unit, didnt taste any difference of the water. Called tech support and was told to look at the water line. Saw the stainless steel braided line breaking down causing the water taste. Advised customer to replace line with copper and new filter. Should fix the taste.SR7741533974Service Fee-$149.95$149.95 CK Auth# CH9RAN"
We serviced a
SAMSUNG RANGE
Model NE63A6511SG/AA
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
05/08/2025
Replaced regulator and tested operation all checks ok
We serviced a
SAMSUNG RANGE
Model NE63T8311SG/AA
Near Pueblo West, Colorado 81007
Domingo
Job Details:
05/08/2025
Call tech line and they recommend to replaced lamp bulb and harness and said that they will only cover the service call told customer they would have to pay for labor and parts customer says they will not do it Lamp bulb DG97-00083AHarness DG96-00808b
We serviced a
SAMSUNG WASHER
Model WA55A7700AV/US
Near Colorado Springs, Colorado 80923
Mathew
Job Details:
05/08/2025
Replace control. Test op. All okay.
We serviced a
LG COOKTOP
Model LREL6325F/02
Near Colorado Springs, Colorado 80911
Jerimiah
Job Details:
05/08/2025
"Cooktop has large chip directly in center of left front surface burner, doesnt appear to be customer related damage. Cooktop needs replacing. Labor would be $219.95. Charging service call $139.95 CC Auth# F3V434AGU76970511 Glass top $646.01"
We serviced a
WHIRLPOOL DRYER
Model WED5100HC3
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
05/08/2025
Installed motor ran complete timed dry cycle runs all ok
We serviced a
GE STACK UNIT
Model GUD27ESSM1WW
Near Colorado Springs, Colorado 80916
Charles
Job Details:
05/08/2025
"Unit full of water, lid not locking for drain and spin, bent in top panel causing lock issue. Held lid, started drain and spin, unit drained all water and spun. Had to wait 30 minutes for person with payment. Service fee $139.95, paid check#1411 autho 4PFPKV $139.95"
We serviced a
WOLF WALL OVEN
Model SO30TE/S/TH
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
05/08/2025
Showed customer how to install light bulbs in oven cavity. Customer wishes to replace them himself. RKService call 159.95Auth P3XYXM
We serviced a
LG DISHWASHER
Model LDFC353LS.ASSEEUS
Near Colorado Springs, Colorado 80909
Mauricio
Job Details:
05/08/2025
Upon arrival outter door panel was perfect problem was inner tub was dent on bottom left in tub you could not see dent until lower rack was removed inner tub is a non repairable part spoke with lg triage TCC250508398104 for Ticket No : 641870 // case documented for RNN250430098270 // - Is there anything else I can help you with today? (This chat will terminate in 15 seconds if there is no response)Reply STOP to opt out.
We serviced a
LG RANGE
Model LSEL6335FF.ARSLLGA
Near Colorado Springs, Colorado 80915
Jerimiah
Job Details:
05/08/2025
"Installed replacement switches, unit check ok"
We serviced a
LG REFRIGERATOR
Model LSXS26366S/02
Near Colorado Springs, Colorado 80918
Ralph
Job Details:
05/08/2025
"called tech support, ran some test and tech is saying unit has a slight restriction, wants me to cut out the compressor and also run flush through the system with nitrogen to clear any impurities and try to clear the slight restriction, ordering compressor and filter drier, compressor TCA36691603 warrantied part, filter drier ADH73590310 89.99, tax 7.38, labor 695.95, refrigerant 255.00, total 1048.32, cust paying service fee today...autho no. R3UPK9"
We serviced a
LG FREEZER
Model LSXS26366S.ASTCNA0
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
05/08/2025
"Updated s/w on main board, replaced compressor and drier, vacuumed and charged unit all checks ok"
We serviced a
LG DISHWASHER
Model LDTH7972S
Near Palmer Lake, Colorado 80133
Dvante
Job Details:
05/08/2025
"Checked unit, found the extension cord that Home Depot installed was shorted. Customer would need another extension cord or the right power cord for the unit to be able to sit flushed back. Unit is operating as designed."
We serviced a
KENMORE REFRIGERATOR
Model 795.72043.110
Near Pueblo West, Colorado 81007
Domingo
Job Details:
05/08/2025
Customer says door was left open and I find the top of refrigerator frozen defrost it and told customer to monitor everything test it good the heater was working the froze was on the top of it charge SC $139.95 see pic
We serviced a
MAYTAG DRYER
Model MED6230RHW1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
05/08/2025
"Heating element is shorted out, thermostats check out okay, approved onsite, removed and replaced element, tested unit, working and heating well now. Element $104.62Tax $8.58Supplies $14.50Hc $139.95Labor $199.95Total job $467.60No return on parts Auth total job $467.60 ck 2548 #4T4W3P; used 1 Wp3387747 (Element) from stock"
We serviced a
GE WASHER
Model GFW650SPN3SN
Near Granby, Colorado 80446
Antonio
Job Details:
05/08/2025
Installed new motor then ran a cycle for proper operation and unit tested goodLb $189.95Mpg17.50$207.45 CC Auth# VJJ34E
We serviced a
JENNAIR REFRIGERATOR
Model JFFCC72EHL04
Near Winter Park, Colorado 80482
Antonio
Job Details:
05/08/2025
Installed new water valve unit testing good
We serviced a
JENN-AIR WALL OVEN
Model JJW2830DS01
Near Colorado Springs, Colorado 80923
David
Job Details:
05/08/2025
"Pulled wall oven, checked all wiring and elements, all good. Tested, and both ovens came up to temp and no smoke."
We serviced a
SAMSUNG DRYER
Model DVE55A7700V/A3
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
05/08/2025
Found lint obstruction in vent filter housing. Clear obstruction and test all components. All okay. Educate on eco dry. Collect svf 139.95. $139.95 CC Auth# HP4AFE
We serviced a
GE REFRIGERATOR
Model GTS22KYNDRFS
Near Basalt, Colorado 81621
Sean
Job Details:
05/08/2025
Checked packages = Good.I opened the freezer and removed everything in it.Removed shelves and the ice maker.Removed back panel. Unplugged the unit.Removed the old fan motor.Installed the new fan motor and grommet and bushing.Put on the new fan blade. Reassembled the unit.Plugged the unit in and tested = fan started up it did not rub and tested good. Put all the food back in the freezer.Unit is cooling down to temp again.Operating as designed by factory.If you are satisfied with the service I provided for you today please take a moment and go online and fill out a technician survey.Thank you.Technician. Sean
We serviced a
GE RANGE
Model CEP90301T1BB
Near Aspen, Colorado 81611
Sean
Job Details:
05/08/2025
Checked the unit MN SN Customer not home to sign.Checked the package=GoodLifted up the range and unhooked power removed it from counter top. Removed the glass from range and proceeded to unhook all burners and connectors. Installing them on the new glass top as I go. Reassembled the range. Hooked up power and Put it back in the counter top. Tested the range all burners are working took pictures of them hot.Cleaned up around aria .Thank you and if you appreciate the service I provided you today please let others know about it and go online and fill out a technician survey.
We serviced a
GE WASHER
Model GTW220ACW0WW
Near Colorado Springs, Colorado 80916
Charles
Job Details:
05/08/2025
"UNIT#108 Will not spin or agitate, belt off pulleys, reinstall belt, clear codes, ran diagnostic cycle, agitation and spin."
We serviced a
GE REFRIGERATOR
Model UNC15NPWBII
Near Colorado Springs, Colorado 80904
David
Job Details:
05/08/2025
"On arrival, the icemaker was full of water. Started pulling unit out of cabinet when the pump started. Sensor good, wire harness loosing continuity in plug of harness at the sensor.Will call tech line when they are out of meeting. Got ahold of tech line. Case number 16634706.Wire harness not available. Customer relations will contact for exchange."
We serviced a
ELECTROLUX DRYER
Model ELFE7637AT0
Near Colorado Springs, Colorado 80908
Dvante
Job Details:
05/08/2025
"Checked unit, found the grinding noise. Saw the build up of lint in blower. Checked the rollers and pulley. All rolling properly. Cleaned blower. Tested unit, no grinding noises. Unit is operating as designed."
We serviced a
ELECTROLUX WASHER
Model ELFW7437AW2
Near Jacksonville, Oregon 97530
Jeff
Job Details:
05/08/2025
Installed parts tested machine working as should no errors
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5021SG/AA
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
05/08/2025
"Replaced compressor, vacuumed and charged unit, tested operation all checks ok hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23J9011SR/AA
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
05/08/2025
$139.95 CC Auth# 934LUM
We serviced a
FISHERPAYKEL DISHWASHER
Model DD24STI9N
Near Colorado Springs, Colorado 80921
Charles
Job Details:
05/08/2025
Installed door pin
We serviced a
DACOR RANGE
Model DOP48C86DLM/DA
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
05/08/2025
"Door latch dg66-00041a Found display off, buttons blinking. Unit has a tco issue. Called Dacor to confirm. Agent recommends inspecting tco at back of unit before going to the one under cooktop. I could not move stove myself, I will need airsled on return. Unit is 48. Svf $159.95DE47-20037A thermostat $55.30DG47-00010A thermostat $61.88Tax $9.61MPs$14.50 Labor $269.95$571.19If cooktop needs to come off labor will double and will need Door latch dg66-00041a $274.42Tax $22.50Labor $269.95$1138.06 ; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)"
We serviced a
KITCHENAID DISHWASHER
Model DDT595SSJ5SS
Near Colorado Springs, Colorado 80906
Mauricio
Job Details:
05/08/2025
$139.95 CC Auth# VP4RAC tested all components with multimeter no response from inlet valve or motor pump max would like to think about it $7.00 CC Auth# J44N3F
We serviced a
SUBZERO REFRIGERATOR
Model IC-30R
Near Monument, Colorado 80132
Ryan
Job Details:
05/08/2025
Installed components and recharged system. Unit is now cooling and temps are dropping. RKCustomer paid balance $1409.00Auth N3XF33
We serviced a
SUB ZERO REFRIGERATOR
Model IC-30RID-RH
Near Peyton, Colorado 80831
Ryan
Job Details:
05/08/2025
Replaced leaky high side valve core.on filter drier. RK
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSG/AA
Near Colorado Springs, Colorado 80951
Mathew
Job Details:
05/08/2025
"Found rattling noise coming from inside of compressor. Tried to apply permagum to reduce noise, noise still present. Unit will need compressor replacement to fix issue. Based on purchase date unit is outside of full sealed system warranty. $139.95 CC Auth# HW439RSvf $139.95Compressor drier $200.80process stub $119.78Tax $26.28Due today $486.81Labor $695.95Refrigerant. $255.95$1408.71"
We serviced a
BOSCH DISHWASHER
Model SHP78CM4N/22
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
05/08/2025
Found traces of water in pan underneath however could not replicate leak or verify a part failure at this time. Ran complete diagnostic test cycle
We serviced a
BOSCH REFRIGERATOR
Model B36CT80SNS/11
Near Carbondale, Colorado 81623
Sean
Job Details:
05/08/2025
Checked the unit MN SN Customer signed disclaimer.Looked at the unit . It has slight ice buildup on back panel.Gaskets are good the ice maker is working at the moment.Called Bosch support explained what is going on .Got case number ( 4105220099 ) to extend claim time on unit .Unit is operating properly within manufacturer specifications.Thank you and if you are happy with my service and performance than please go on line and let other people know about your experience.Thank you.
We serviced a
BOSCH RANGE
Model HII8057U/06
Near Fraser, Colorado 80442
Erik
Job Details:
05/08/2025
ACCESS WITH KEY FROM CXinstall/ test: PASS* see quick picsJOB COMPLETECX not available for signature
We serviced a
THERMADOR RANGE
Model PRG305WH/06
Near Winter Park, Colorado 80482
Erik
Job Details:
05/08/2025
ACCESS WITH DOOR CODEinstall parts on site/ test: PASSJOB COMPLETECX not available for signature
We serviced a
THERMADOR RANGE
Model PRG366WH/05
Near Winter Park, Colorado 80482
Erik
Job Details:
05/08/2025
ACCESS WITH DOOR CODEinstall parts and test: PASSoven no longer trips breaker/ left front/ rear burners operate normallyJOB COMPLETECX not available for signature
We serviced a
BEKO REFRIGERATOR
Model BFFD30216SSIM
Near Cañon City, Colorado 81212
James
Job Details:
05/08/2025
Installed ordered parts tested ops all ckok
We serviced a
KITCHENAID REFRIGERATOR
Model KFIS29PBMS02
Near Glenwood Springs, Colorado 81601
Josh
Job Details:
05/08/2025
"Customer signed disclaimer. Verified MN SN.Customer states that unit is under-performing ice production. Technician verified unit is operating properly, creating well formed milky cubes. Technician notes that unit is approximately 1/3 full. All functions are working properly according to manufacturer specifications."
We serviced a
MAYTAG DRYER
Model MED7230HW
Near Fountain, Colorado 80817
Brandon
Job Details:
05/08/2025
Replaced sensor and tested operation all ok
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Colorado Springs, Colorado 80911
Charles
Job Details:
05/08/2025
"Grinding noise from rotor bolt fell out, secured with loctite."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near White City, Oregon 97503
Thomas
Job Details:
05/08/2025
Replaced ice maker assembly. Customer will monitor. Advised customer of survey
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
05/08/2025
"Removed and replaced inlet valve, tested unit, working well now, no leaks, verified by customer, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM11
Near Bend, Oregon 97702
Levi
Job Details:
05/07/2025
Replace the evaporator fan motor and fan blade tested all checks okay
We serviced a
WHIRLPOOL RANGE
Model WFES3330RS0
Near Bend, Oregon 97702
Levi
Job Details:
05/07/2025
Replace door seal and checked okay
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC700HBS00
Near Roseburg, Oregon 97471
Jeff
Job Details:
05/07/2025
Installed parts and had issues with possible moisture in one of the evaps. Redid and pulled down from both sides refilled and tested. Unit is cooling and gauges are holding good.
We serviced a
MAYTAG WASHER
Model MHW5630MBK0
Near Colorado Springs, Colorado 80909
Mauricio
Job Details:
05/07/2025
Filter was clogged with hair and other objects disassembled unit to get to the drain filter cleaned off all of the hair and debris that was blocking drain pump unit tested to spec
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Woodland Park, Colorado 80863
David
Job Details:
05/07/2025
"Installed control, tested, water level came up a lot better."