We serviced a
KITCHENAID REFRIGERATOR
Model KRFC136RPS00
Near Bend, Oregon 97701
Richard
Job Details:
01/12/2026
Replaced ice maker and valve cycled unit all tested fine
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRSF705HPS04
Near Bend, Oregon 97702
Richard
Job Details:
01/12/2026
Install new filter housing assembly cycle tested unit all checks. Good at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ19
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
01/12/2026
"Removed and replaced compressor, drier, and evaporator, charged and monitored unit, internal leak, checked all connections, compressor at .4amp, discussed situation with techline, sent for review, whirlpool to contact customer. Advised customer of situation and survey. Case number 22185778"
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ2
Near Grand Junction, Colorado 81506
Clint
Job Details:
01/12/2026
Customer recieved parts control and sensor.installed control and sensor put in service mode to reset faults.ran unit in normal cycle and seems to be running normally. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Gypsum, Colorado 81637
Antonio
Job Details:
01/12/2026
"Installed new icemaker, evap fan and ui panel then cycled unit on for proper operation and unit tested good Also advised cx of whlp survey"
We serviced a
WHIRLPOOL DRYER
Model MED5500FW2
Near Albuquerque, New Mexico 87120
Larry
Job Details:
01/12/2026
CX complaint - Dryer making loud squeeling - Inspected unit and found support rollers failing - Installed repair kit and tested good - Unit is good to go - Survey mentioned
We serviced a
SAMSUNG WASHER/DRYER COM
Model WD90F53AVYUS
Near Elbert, Colorado 80106
Mathew
Job Details:
01/12/2026
Replace harness. Test op all okay.
We serviced a
GE RANGE
Model GGF500PV2BB
Near Eagle, Colorado 81631
Erik
Job Details:
01/12/2026
install/ test: passJOB COMPLETE
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS01
Near Colorado Springs, Colorado 80919
Charles
Job Details:
01/12/2026
Installed listed parts
We serviced a
FISHERPAYKEL DISHWASHER
Model DD24DT19N
Near Monument, Colorado 80132
Charles
Job Details:
01/12/2026
Replaced water hose for upper and lower drawer due to mouse damage. Ran rinse cycle on upper and lower with no leaks.
We serviced a
WOLF RANGE
Model DF484CG
Near Colorado Springs, Colorado 80908
Charles
Job Details:
01/12/2026
"Complaint of ovens not maintaining temperature, set to 350, preheated to 350 in 20 minutes, cycles as normal, raised temperature to 425, heated to 425. Unable to verify complaint of low temperature. Service fee &169.95 paid 3AMKN3"
We serviced a
LG DRYER
Model DLE6100W.ABWETUS
Near Pueblo, Colorado 81007
Domingo
Job Details:
01/12/2026
Replaced drum test it no noise
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
01/12/2026
"Removed and replaced components, tested unit through diagnostics, working well now, purged water. Advised customer of 5 star survey."
We serviced a
JENN-AIR OVEN
Model JJW2830IL00
Near Albuquerque, New Mexico 87120
Larry
Job Details:
01/12/2026
Installed UI and tested good - Unit is good to go - Survey mentioned
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS3
Near Vail, Colorado 81657
Antonio
Job Details:
01/12/2026
Installed new pump assembly then ran a cycle for proper operation and for leaks unit tested good Also advised cx of whlp survey
We serviced a
BOSCH DISHWASHER
Model SHE863WF5N
Near Colorado Springs, Colorado 80916
Ralph
Job Details:
01/12/2026
"UNIT HAD AN OBSTRUCTION WITHIN THE DRAIN HOSE, CLEARED THE OBSTRUCTION AND UNIT CHECKED OKAY"
We serviced a
LG DRYER
Model DLEX9000V
Near Colorado Springs, Colorado 80924
Ryan
Job Details:
01/12/2026
Unit working fine at this time. Vent loose at wall causing extended dry time. Advised customer to replace flexible vent with rigid venting and seal everything with foil tape. RK149.95Auth KH93VR
We serviced a
GE DRYER
Model GFD85GSPN1RS
Near Colorado Springs, Colorado 80924
Ryan
Job Details:
01/12/2026
"Replaced gas valve and tested operation, unit is now working properly. RK"
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Albuquerque, New Mexico 87107
Larry
Job Details:
01/12/2026
Installed parts listed and tested good - Unit si good to go - Survey mentioned
We serviced a
BOSCH REFRIGERATOR
Model B36FD50SNS04
Near Grants Pass, Oregon 97526
Chris
Job Details:
01/12/2026
I called TS. They had me disconect the refrigerator to reset the code. The error is gone.
We serviced a
WHIRLPOOL WASHER
Model WFW6620HW2
Near Albuquerque, New Mexico 87106
Jason
Job Details:
01/12/2026
Installed hose ran a quick cycle. unit opperation checks ok. spoke to cx about review
We serviced a
BOSCH RANGE
Model HDS8655U/04
Near Colorado Springs, Colorado 80918
Ryan
Job Details:
01/12/2026
"Replaced UI and cable. Adjusted burners. All burners now work ,preheated oven successfully and waited awhile. All now working properly. RK"
We serviced a
SAMSUNG REFRIGERATOR
Model rf29bb89008maa
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
01/12/2026
"Repaired leak, replaced compressor and drier and tested operation all checks ok"
We serviced a
GE OVEN
Model JB625RK9SS
Near Colorado Springs, Colorado 80917
Earl
Job Details:
01/12/2026
"I arrived in diagnosed unit as a bad potentiometer.The customer declinedHe said he was not going to pay us cause he's going through net.Fender , sterling knows the rest of it , leaving without any kind of payment"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Grants Pass, Oregon 97526
Chris
Job Details:
01/12/2026
The thermal cutoff activated. I replaced it and checked the air flow to the outside. It has very poor air flow. I recommended having vent cleaned and inspected.
We serviced a
MAYTAG DRYER
Model MEDB835DW4
Near Roseburg, Oregon 97471
Chris
Job Details:
01/12/2026
Replaced the element and cut off. Tested
We serviced a
MAYTAG WASHER
Model MVW5430PBK0
Near Roseburg, Oregon 97470
Chris
Job Details:
01/12/2026
Replaced the lower wire harness and lid lock. Tested
We serviced a
SAMSUNG RANGE
Model NX60A6751SS/AA
Near Seaside, Oregon 97138
Nathan
Job Details:
01/12/2026
#4183642486Air fryer is working as designed Heating and fans are running per tech line Visual support with tech line about scratches and discolor on cooking grates Tech line deemed all cosmetic and not covered by their warranty Advised CX of survey
We serviced a
SAMSUNG REFRIGERATOR
Model RF4287HARS/XAA
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
01/12/2026
"Found micro switch on dispenser broken. Only repairable as an assy, quote good 30 days. Svf 149.95$149.95 CK Auth# XHP349MPs 14.50Part $460.07Tax $37.72Labor 189.95"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Grand Junction, Colorado 81501
James R
Job Details:
01/12/2026
Signed disclaimer. Put into service diagnjostics no error codes present. Put thru a quick service test. Cold wtr comes in slow. Replaced valve and then test again is operating as designed. While testing could hear the agitate wobble checked it bolt is loose replaced it W10752187 Loktited it and tightened really tight. Please fill out tech satisfaction survey. Thank You. ; used 1 W10752187 (Screw) from stock
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5101SG/AA
Near Fountain, Colorado 80817
Brandon
Job Details:
01/12/2026
"Replaced compressor and drier and repaired leak, tested operation all checks ok"
We serviced a
GE DISHWASHER
Model GDT670SYV1FS
Near Seaside, Oregon 97138
Nathan
Job Details:
01/12/2026
Loose connection at water inlet valve causing leak Unit un level
We serviced a
MAYTAG WASHER
Model MVW6230RHW2
Near Colorado Springs, Colorado 80917
David
Job Details:
01/12/2026
"Actuator stripped out, splines of cam waring out. Replaced cam and Actuator, ran calibration and diagnostic cycles, all good."
We serviced a
SAMSUNG RANGE
Model NK30B3500US/AA
Near Pueblo, Colorado 81005
Domingo
Job Details:
01/12/2026
Replaced control with driver test it and it came on everything is working correctly
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
01/12/2026
Found debris in track and lint clog in vent removed both unit runs all ok recommend cx have vents inspected
We serviced a
WHIRLPOOL RANGE
Model WFES5030RZ0
Near Grand Junction, Colorado 81504
Clint
Job Details:
01/12/2026
"Customer recieved parts ordered,installed parts and ran oven its now getting 240 volts to the lower element and heating properly. PLEASE TAKE TECH SURVEY THANKS.CLINT"
We serviced a
GE GAS RANGE
Model CGS750P2M5S1
Near Avon, Colorado 81620
Erik
Job Details:
01/12/2026
oven offset by 25 degrees on upper oven and gas smell coming from lower ovenclose flue shutter on lower bake and broil/ test: smell abatedcorrect offset on upper oven and test: pass ( 350 is acurate now) job complete
We serviced a
KITCHENAID DISHWASHER
Model KDPS624SPS0
Near Redmond, Oregon 97756
Richard
Job Details:
01/12/2026
Install new sump assembly cycle tested unit all tested good at this time unit working as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ03
Near Colorado Springs, Colorado 80917
David
Job Details:
01/12/2026
"Replaced icemaker, ran cycle to fill. Cx monitor."
We serviced a
SAMSUNG WALL OVEN
Model NQ70CG700DMTAA
Near Colorado Springs, Colorado 80921
David
Job Details:
01/12/2026
"Called tech line, setup video call, he deamed it none repairable, frame and microwave damage, case number is the serial number."
We serviced a
GE WASHER
Model GFW850SPN5RS
Near Monument, Colorado 80132
Earl
Job Details:
01/12/2026
I installed the door switch the control board and the harness unit is operating properly at this time. This one has the personality of number 4.
We serviced a
MAYTAG DISHWASHER
Model MDBTT60AWQ
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
01/12/2026
"unit has a faulty board, cust not repairing, too costly for this repair...autho no. T9JMX9"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Peyton, Colorado 80831
Aaron
Job Details:
01/12/2026
"Heating element and thermostat are shorted out, removed and replaced components, tested unit, working and heating well now, recommend wall vent to be professionally cleared. Advised customer of situation and survey."
We serviced a
GE REFRIGERATOR/TOP
Model GSE25GYPFCFS
Near Avon, Colorado 81620
Erik
Job Details:
01/12/2026
dirty condensing unit - clean and connect to smartHQno errors or alertsjob completecollect 229.95 sc AUTHO#N9U4NK
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80926
Carlos
Job Details:
01/12/2026
Installed control board runs all ok.
We serviced a
GE WASHER
Model GFW655SPVODS
Near Grand Junction, Colorado 81504
Clint
Job Details:
01/12/2026
"Customer signed disclaimer and had part ,put control in set personality 17 number 9. Ran. Unit and sounded and ran good no leaks.PLEAESE TAKE TECH SURVEY THANKS.CLINT."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Pueblo, Colorado 81001
James
Job Details:
01/12/2026
Installed all ordered parts tested ops all ckok
We serviced a
FRIGIDAIRE RANGE
Model GCFG3060BFA
Near Kiowa, Colorado 80117
Earl
Job Details:
01/12/2026
"Uninstall, the new control board in Tempe and tested unit.The unit is working at this time"
We serviced a
MIDEA DRYER
Model MLE45N1BWW
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
01/12/2026
Debris found in blower removed runs all ok.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
01/12/2026
"Found blown element, bad thermal fuse. Install fuse kit and element. Test op, unit working as expected."
We serviced a
WHIRLPOOL MICROWAVE
Model WMMF7330RZ00
Near Colorado Springs, Colorado 80927
David
Job Details:
01/12/2026
Checked and repositioned metal. All good. Cx said that the microwave is keeping time and not powering off.
We serviced a
SAMSUNG WASHER
Model WF45B6300AP/US
Near Tillamook, Oregon 97141
Nathan
Job Details:
01/12/2026
Replaced ripped door gasket Tested for leaks No leaks Switched hoses around for CX as they were installed backwards Advised of survey
We serviced a
MIELE COFFEE MACHINE
Model CVA7370
Near Colorado Springs, Colorado 80922
Charles
Job Details:
01/12/2026
"Brewed coffee is warm 115 degrees, not hot, pulled unit, getting 240v at 120v outlet, tested at 120 outlet and coffee is hot. Needs electrician to correct outlet voltage."
We serviced a
MONOGRAM REFRIGERATOR
Model ZIW303NPPBII
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
01/12/2026
"found units magnet had released itself from the adhesive, and was stuck to the drawer, cust feels ice bucket is defective, and he wants a replacement. i called the paying party and told what was found, and the cost of the part, he has never gotten back with me, so closing out call with noters, part cost for the ice bucket 524.84 + tx 43.04 = 567.88"
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
01/12/2026
"Recommend cx havre plumber inspect drain, unable to replicate issue"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87111
Jason
Job Details:
01/12/2026
Installed control unit opperation checks ok
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFUE2024AWF
Near Grants Pass, Oregon 97526
Chris
Job Details:
01/12/2026
The customer wasn't at home.
We serviced a
SAMSUNG WASHER
Model WF45K6500AV/A2
Near Fountain, Colorado 80817
Brandon
Job Details:
01/10/2026
"Error dc3, door switch didnt activate, reset and did smart diagnostic all checks ok svf paid $139.95 CC Auth# P43KMC"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT549SZDM06
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
01/10/2026
"Evaporator fan motor bearings are loud, removed and replaced motor and blade, unit needs time to cool. Advised customer of situation and survey."
We serviced a
SUBZERO REFRIGERATOR
Model 700TR3
Near Colorado Springs, Colorado 80909
Charles
Job Details:
01/10/2026
"Replaced compressor, Labor $1395.95 paid check #102 autho X3W99M"
We serviced a
WHIRLPOOL STACK UNIT
Model WETLV27HW3
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
01/10/2026
"F0E5 error code in diagnostics, off balance load, corrected lower harness and tested unit, working well now. Advised customer of situation and survey."
We serviced a
SAMSUNG WASHER
Model WA50R5200AW/US
Near Pueblo, Colorado 81005
Domingo
Job Details:
01/10/2026
Replaced shocks and ran hass it passed
We serviced a
SAMSUNG RANGE
Model NSE6DG8100SRAA
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
01/10/2026
Replaced regultors and tested operation all checks ok
We serviced a
JENNAIR ICE MACHINE
Model JIM158XYRS
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
01/10/2026
Installed new drain pump and tested operation. unit is now making ice.RK
We serviced a
WHIRLPOOL DRYER
Model WED8127LW1
Near Colorado Springs, Colorado 80951
Carlos
Job Details:
01/10/2026
Installed element unit runs all ok Cx paid in full $ 496.37 CK Auth# JYFC39
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
01/10/2026
"Replaced control and lower harness, recalibrated and tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
WOLF OVEN
Model SPO30PM/S/PH
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
01/10/2026
"Installed new touchpad and screen, Tested operation and all now checks ok.RK"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Colorado Springs, Colorado 80917
David
Job Details:
01/10/2026
"Roller making a lot of noise, installed repair kit. Much quieter."
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Colorado Springs, Colorado 80918
Earl
Job Details:
01/10/2026
I installed the new user interface and tested unit is operating properly at this time
We serviced a
ELECTROLUX WASHER/DRYER COM
Model ELFE7637AT
Near Larkspur, Colorado 80118
Earl
Job Details:
01/10/2026
Customers complaint unit making a rattling sound and not drying in certain settings. I explained to them how to use The Dry boost on the unit and tested the unit. The unit just needed to be tightened down a little bit. There's no more noise coming from it. That's abnormal unit operating properly at this time
We serviced a
WHIRLPOOL DISHWASHER
Model VFGDFDSHBG
Near Colorado Springs, Colorado 80920
Brandon
Job Details:
01/10/2026
"Not draining fully, removed restricting extension on drain line and routed and secured drain line and tested operation all checks ok"
We serviced a
GE DRYER
Model GFDR480EF1WW
Near Colorado Springs, Colorado 80906
Charles
Job Details:
01/10/2026
"Loud noise from from roller failure, need 6 of drum roller WE03X10016, Service fee $149.95, Labor $249.95, MPS $14.50, Parts $470.28, Tax $38.56, Total $923.24, declined estimate, paid service fee autho T4M33M"
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ3
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
01/10/2026
Replaced rack adjusters and leveled unit so that door now closes. All now checks ok. RK
We serviced a
LG WASHING MACHINE
Model WM8100PVA
Near Colorado Springs, Colorado 80906
Mathew
Job Details:
01/10/2026
Replace pump assy. Test op. Unit working as expected. Collect labor 209.95 $209.95 CC Auth# 33WKKA
We serviced a
WHIRLPOOL DRYER
Model WED8127LC1
Near Colorado Springs, Colorado 80919
Earl
Job Details:
01/10/2026
"Customers complaint unit not drying anymore.I replaced the thermostats, and the heating element unit is operating properly.At this time , customer paid full price authorization codeX9EAR3"
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Fountain, Colorado 80817
Earl
Job Details:
01/10/2026
"Customers complaint unit.\nNot coming on and staying on , I CALIBRATED, THE UNIT AND THEN RAN A DIAGNOSTIC CYCLE ON A CLEARED.EVERYTHING OUT AND TESTED.THE UNIT UNIT IS OPERATING PROPERLY AT THIS TIME"
We serviced a
ELECTROLUX DRYER
Model EFME627UTT0
Near Colorado Springs, Colorado 80906
Charles
Job Details:
01/10/2026
Replaced blower wheel
We serviced a
SAMSUNG WASHER FRONT LO
Model WV55M9600AV
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
01/10/2026
Found debris in drain pump. Remove debris. Test op all okay. Svf 139.95 $149.95 CC Auth# 9WLFTX; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)
We serviced a
SAMSUNG RANGE
Model NSE6DG8300SRAA
Near Colorado Springs, Colorado 80910
Ralph
Job Details:
01/10/2026
"WHEN I ARRIVED AT THE CUST HOUSE AND HE WAS TRYING TO SHOW ME THE ISSUE, THERE WASNT ONE, TOLD CUST IF ISSUE ARISES AGAIN TO GIVE US A CALL"
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Fountain, Colorado 80817
Earl
Job Details:
01/10/2026
Customers complaint unit making a rattling. I arrived and took the unit apart and found a couple of screws that had worked their way back out. So I tightened them back down unit is operating properly at this time.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
01/10/2026
"Loose connection at control, corrected and leveled unit, tested, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
01/10/2026
"Thermal fuse and heating element are shorted out, removed and replaced components, tested unit, working well now. Advised customer of situation and survey."
We serviced a
BOSCH GAS COOKTOP
Model NGME656UC01
Near Winter Park, Colorado 80482
Antonio
Job Details:
01/10/2026
Just needed to tighten gas line $285.95 CC Auth# T9WT3E
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRQC2255BF
Near Parshall, Colorado 80468
Antonio
Job Details:
01/10/2026
Installed new ui panel then cycled unit on unit is testing good
We serviced a
MAYTAG WASHER
Model MVW5435PW1
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
01/10/2026
"Installed gear case, belt and cam all ok Cx"
We serviced a
LG REFRIGERATOR
Model LFCS27596S
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
01/10/2026
Replaced gasket all checks ok
We serviced a
GE RANGE
Model P2B912DEM1WW
Near Colorado Springs, Colorado 80919
David
Job Details:
01/10/2026
"Checked range for leaks, confirmed tightness of connections to the pressure regulator. Gas company had marked the conversion cap as a possible source of smell. Tightened cap and bubble checked. No bubbles."
We serviced a
SAMSUNG MICROWAVE OVEN
Model ME19R7041F
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
01/10/2026
Replace door test op all okay.
We serviced a
FRIGIDAIRE WALL OVEN
Model GCWM3067AFB
Near Larkspur, Colorado 80118
Ryan
Job Details:
01/10/2026
Replaced broken magnetron sensor and tested operation ok. Unit is now working properly. RK
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS05
Near Colorado Springs, Colorado 80923
David
Job Details:
01/10/2026
"Checked refrigerator, found defrost drain frozeup, also found a couple pieces of foam in the drain restricting the flow of defrost water and freezing. Cleared obstruction, good flow."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRMC2273CF02
Near Larkspur, Colorado 80118
Ryan
Job Details:
01/10/2026
Replaced UI and main control. All now working properly. RK
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
01/10/2026
Installed console runs all ok Cx
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
01/10/2026
"Hire harness connection not fully engaged, corrected and tested unit, improper power between L2 and common, recommend electrician. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Parachute, Colorado 81635
James R
Job Details:
01/09/2026
Signed disclaimer. Replaced control per SP W11766193 S code S153EB Checked pressure tube it is not blocked or kinked is clear. Calibrated and then tested in quick service test no error codes when done unit is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
MAYTAG DRYER
Model MED6205RW0
Near Seaside, Oregon 97138
Nathan
Job Details:
01/09/2026
Loose connection at ACU Advised CX of survey Tested and working
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Grand Junction, Colorado 81504
Sean
Job Details:
01/09/2026
Verified the information & customer signed disclaimer.Pulled the unit out and leaned it back removed the motor cover and belt.Removed the splutch kit and installed the new one.Reassembled the unit. Started a quick wash and unit started and operating as designed by factory.Thank you Your technician Sean.
We serviced a
MAYTAG DRYER
Model MED5430MW0
Near Albuquerque, New Mexico 87123
Jason
Job Details:
01/09/2026
Installed parts listed. ran timed dry cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Albuquerque, New Mexico 87105
Jason
Job Details:
01/09/2026
CHecked unit found motor pulley had broke. installed parts listed unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ
Near Grand Junction, Colorado 81504
Sean
Job Details:
01/09/2026
Verified information customer signed disclaimer.Opened the freezer and removed the ice maker .Installed the new ice maker and turned it on.Unit tested good Thank you.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ15
Near Grand Junction, Colorado 81501
James R
Job Details:
01/09/2026
"Signed disclaimer. Evac system. Then replaced the drier, compressor and installed a new overload relay. Pressure tested system up to 250 psi took pic and checked for leaks by bubble testing joints all ok. Evac system again to -24 low side and high in a vac as well. Recharge system low side -8 high side 65 psi good. Unit is cooling. Please fill out tech satisfaction survey. Thank You.; used 1 W11506635 (COUPLER) from stock"

