We serviced a
AMANA RANGE
Model AER6303MFB5
Near Albuquerque, NM 87121
Larry
Job Details:
05/06/2024
Installed cooktop and tested good - Unit is good to go
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAEWW/AA 07 RF
Near Colorado Springs, CO 80911
Mathew
Job Details:
05/06/2024
"Found iceroom frozen over. Defrosted room, checked seals. All okay. Installed icemaker repair kit, test op all okay."
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Falcon, CO 80831
Aaron
Job Details:
05/06/2024
"Replaced switch assembly and bulb, tested unit, working well, verified by customer. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5201SG/AA 00 RF
Near Colorado Springs, CO 80922
Brandon
Job Details:
05/06/2024
"Replaced ice maker, tray, auger and ice route and tested op all checks ok hass oqc passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23R6201DT/AA
Near Colorado Springs, CO 80906
Mathew
Job Details:
05/06/2024
"Replaced faulty icemaker, test op all okay. Collect labor $179.95. Paid by check."
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Albuquerque, NM 87114
Larry
Job Details:
05/06/2024
"CX complaint - Washer senses, doesn't cycle - Inspected unit and found F7E4 and the slider failed - Replaced with TS and tested good - Unit is good to go; used 1 W10734521 (Slider) from stock"
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Colorado Springs, CO 80920
Eric
Job Details:
05/06/2024
"Customer complained that oven was not heating properly as well as microwave not heating enough. Put wall oven into diagnostic mode and found that programming was incorrect, adjusted accordingly and tested all components. Double checked microwave, heating properly at this time. Conducted some customer education of product. Customer to monitor if problem reoccurs recommend replacing control board. Informed customer of survey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Albuquerque, NM 87107
Larry
Job Details:
05/06/2024
Installed UI and tested good - Unit is good to go
We serviced a
KITCHENAID DISHWASHER
Model KDFE104HPS0
Near Colorado Springs, CO 80917
Eric
Job Details:
05/06/2024
Replaced failed components and tested. Unit running properly at this time. Installed litmus stripe and informed customer of survey.
We serviced a
SAMSUNG WASHER
Model WF45B6300AC/US
Near Colorado Springs, CO 80927
Brandon
Job Details:
05/06/2024
Replaced sub PBA and tested op all checks ok hass oqc passed
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Albuquerque, NM 87107
Larry
Job Details:
05/06/2024
Installed UI and tested good - Unit is good to go
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Albuquerque, NM 87107
Larry
Job Details:
05/06/2024
CX compliant - Washer not filling all the way with water - CX INSTRUCT - Explained to cx that the unit fills by weight of the load being washed - Ren DIag and calibration cycles and unit is operating as designed
We serviced a
WHIRLPOOL DRYER ELECTRIC
Model WED8740DW1
Near Colorado Springs, CO 80917
David
Job Details:
05/06/2024
"Installed cx supplied parts, tested and is heating as expected. Cx is going to have vent professionaly cleaned."
We serviced a
SPEEDQUEEN DRYER
Model ADE4BRGS175TW01
Near Colorado Springs, CO 80918
David
Job Details:
05/06/2024
"Replaced heater assembly, tested and running as expected."
We serviced a
WHIRLPOOL DRYER
Model WED5100HW1
Near Colorado Springs, CO 80918
David
Job Details:
05/06/2024
"Checked dryer, did not find any burned wiring inside the dryer. No shorts in the wiring harness. The cord going into the outlet is badly burned. Called safety SR# 7738988843.Cx is called an electrician."
We serviced a
GE WASHER
Model GTW540ASP4WS
Near Minturn, CO 81645
Antonio
Job Details:
05/06/2024
Installed lid lock unit tested good
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Colorado Springs, CO 80908
Aaron
Job Details:
05/06/2024
"Door switches are not properly working, removed and replaced switch harness assembly, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JW3
Near Fountain, CO 80817
Carlos
Job Details:
05/06/2024
"Installed burner, harness, board and sensor"
We serviced a
SAMSUNG DRYER
Model DVE53BB8700VA3
Near Peyton, CO 80831
Brandon
Job Details:
05/06/2024
"Bad high limit thermostat, replace heater assembly and op all checks ok hass oqc passed"
We serviced a
MAYTAG WASHER
Model MVW6200KW3
Near Colorado Springs, CO 80918
David
Job Details:
05/06/2024
"Checked washer, plug on to pump was not fully seated. Removed and reseated plug.Tested and is operating as expected."
We serviced a
AMANA WASHER
Model NFW5800HW2
Near Minturn, CO 81645
Antonio
Job Details:
05/06/2024
Unit has sudsing code Sc $149.95 $149.95 CK Auth# M93L3K
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ4
Near Colorado Springs, CO 80924
Aaron
Job Details:
05/06/2024
"Customer states their oven is not lighting and causing a gas smell, found burner tube grounding screw loose, corrected and tested, lighting well, preheated to unit 350f and lit well each time after, top burners are working well and as designed. Customer not present for signature or to advise of survey. Discussed situation with safety."
We serviced a
SAMSUNG DRYER ELECTRIC
Model DV48J7700EW/A2I
Near Colorado Springs, CO 80915
Mathew
Job Details:
05/06/2024
"Found unit making grinding noise. Cleared obstruction in idler pulley, found two seized support rollers. Removed and cleaned both rollers, test op. Sounds better, if issue persists unit will need two rollers and idler pulley. $129.95 CC Auth# 3NH3H3Svf 129.95DC97-16782A x 2 rollers $172.76DC96-00882C idler $97.56Tax $22.17Labor 179.95"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Colorado Springs, CO 80911
Carlos
Job Details:
05/06/2024
Installed strike and latch runs all ok
We serviced a
WHIRLPOOL RANGE
Model WEG515S0LZ1
Near Grand Junction, CO 81501
James R
Job Details:
05/06/2024
customer sighned cisclaimer.install new electrode . vertify poperation of all burners.all good job complete.please fill out whirlpool tech sattisfaction survey.Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, CO 80911
Carlos
Job Details:
05/06/2024
Installed agitator runs ok
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Colorado Springs, CO 80906
Carlos
Job Details:
05/06/2024
"Installed inner tub and suspension. Ran test, runs ok"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, CO 80906
Carlos
Job Details:
05/06/2024
"Installed timer runs ok. Advised cx to replace hose with semi rigid or solid metal hose, poor ventilation"
We serviced a
JENNAIR RANGE
Model JDSP536HL01
Near Wolcott, CO 81655
Antonio
Job Details:
05/06/2024
Installed blower unit tested good
We serviced a
KITCHENAID COOKTOP
Model KCGS350ESS00
Near Grand Junction, CO 81507
James R
Job Details:
05/06/2024
"customer sighned disclaimer.replace valve on center burner,verify adjustments on all valves.all good job complete.pleassefill out whirlpool tech satisfaction survey.Thank You."
We serviced a
KITCHENAID DISHWASHER
Model KUDSO11JBS1
Near Colorado Springs, CO 80906
Carlos
Job Details:
05/06/2024
Installed links all ok. Cx paid LB $149.95 CK Auth# F93URC
We serviced a
SAMSUNG WASHER FRONT LOA
Model WF45M55OOAZ/A5I
Near Colorado Springs, CO 80918
Brandon
Job Details:
05/06/2024
"Replaced diaphragm and tested op, calibrated, all checks ok, Labor paid $199.95 Auth# 334L9N"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ10
Near Albuquerque, NM 87110
Jason
Job Details:
05/06/2024
found there was no lubrication on rails lubricated rails unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ10
Near Grand Junction, CO 81507
James R
Job Details:
05/06/2024
customer sighned disclaimer.replace faulty mull post.level out unit.all good job complete.please fill out whirlpool tech satisfaction survey.Thank You.
We serviced a
KITCHENAID COMPACTOR
Model KTTS505ESS2
Near Fruita, CO 81521
James R
Job Details:
05/06/2024
"customer sighned disclaimer.replace broken door realese .all good, job complete.pleasse fill out whirlpool tech satusfaction survey.Thank You"
We serviced a
MAYTAG WASHER
Model MVW7232HC2
Near Belen, NM 87002
Larry
Job Details:
05/06/2024
CX complaint - F2E2 error - Arrived and called techline (SR7739029292) - Ran multiple tests and could not duplicate issue - Suspect 'fantom error' from previous repair - Unit is operating as designed
We serviced a
SUBZERO REFRIGERATOR
Model 427RHAG
Near Colorado Springs, CO 80920
Ralph
Job Details:
05/06/2024
installed parts and unit checked okay CUST PAID TOTAL AUTHO NO. J94YHR
We serviced a
SUMMIT ICE MACHINE
Model BIM44G
Near Colorado Springs, CO 80908
Ralph
Job Details:
05/06/2024
INSTALLED PART AND CUST TO
We serviced a
SUB ZERO REFRIGERATOR SID
Model 642/FI
Near Monument, CO 80132
Ralph
Job Details:
05/06/2024
"fingers in the ice mkr were stuck freed them up and ice mkr cycled, cust to monitor and see if unit is working correctly autho no. 4NWMU9"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ00
Near Albuquerque, NM 87111
Jason
Job Details:
05/06/2024
installed valve unit checks ok
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Albuquerque, NM 87111
Jason
Job Details:
05/06/2024
Installed support unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, NM 87112
Jason
Job Details:
05/06/2024
Installed control unit opperation checks ok
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Albuquerque, NM 87112
Jason
Job Details:
05/06/2024
Installed inlet assy unit opperation checks ok
We serviced a
WHIRLPOOL WALLOVEN
Model KOCE500ESS
Near Edgewood, NM 87015
Jason
Job Details:
05/06/2024
installed lamp unit checks ok
We serviced a
KITCHENAID COOKTOP
Model KCGS556ESS02
Near Monument, CO 80132
David
Job Details:
05/06/2024
"Checked and tested old burner head, has quite a bit of popping, replaced burner head and tested. Much better now"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Colorado Springs, CO 80909
Carlos
Job Details:
05/06/2024
"Installed ice maker ran harvest cycle , all ok"
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS2
Near Colorado Springs, CO 80919
Eric
Job Details:
05/06/2024
"Found right rail detached, repaired rail and tested. Unit working properly at this time. Customer stated that leak was not coming from dishwasher but from water filter. Check drain line and fill line no leaks at dishwasher. No parts neededHC $129.95Total $129.95Auth $129.95 Auth#W4A4YT"
We serviced a
JENNAIR WALLOVEN
Model JJW3430IM00
Near Larkspur, CO 80118
Eric
Job Details:
05/06/2024
"Was allowed in with customer not being home. Replaced failed components and tested via diagnostics, unit working properly at this time. Customer not home CSR to send waivers."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5201SR/AA
Near Colorado Springs, CO 80909
Brandon
Job Details:
05/06/2024
"No errors, water dripping from water dispenser, replaced filter case assy, water still dripping, called tech support troubleshooted dispensed gallons and checked connections all ok, still dripping, water pressure possibly to high or air getting into water system"
We serviced a
PROFILE DISHWASHER
Model PDT755SYR3FS
Near Colorado Springs, CO 80906
Roman
Job Details:
05/06/2024
Ran the dw and it started filling an working on all the cycles without the delay coming on. Dw is working fine. Have to be careful not to hit the delay button. Glued the control panel piece back on. Dw is working great Paid sc
We serviced a
WHIRLPOOL REFRIGERATOR
Model W8FRNGFVD00
Near Colorado Springs, CO 80903
Roman
Job Details:
05/06/2024
Fridge is running and noticed a bunch of ice in the freezer section. A lot of it is blocking the vents to the ff section. Recommend clearing the drain hole and cleaning condenser coils. Cleaned the coils and decorated the drain hole and removed all the ice and corn. Recommend keeping the freezer clean so food doesnt fall down. Made sure fridge is working and its working great. Labor $209.95Sc $149.95Total cost $359.90Paid total cost $359.90 CC Auth# WVK4XW
We serviced a
LIEBHERR REFRIGERATOR BOT
Model HCB 2062
Near Colorado Springs, CO 80906
Roman
Job Details:
05/06/2024
Left hand door handle came off. Removed the panel and put the handle back on. Tightened the screws. Sc $149.95Labor 50.00Total cost $199.95Paid cc $199.95 CC Auth# C9E493; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Pueblo, CO 81005
James
Job Details:
05/06/2024
Found until with nozzle loose causing more water to enter unit then designed secured and tested. All ops test good
We serviced a
KITCHENAID RANGE
Model KSEG950ESS1
Near Albuquerque, NM 87114
Joe
Job Details:
05/06/2024
Cx complaint console won't work. Inspected unit. Needs console and control. Customer declined service
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS04
Near Rio Rancho, NM 87124
Joe
Job Details:
05/06/2024
Cx complaint. Not cooling. Replaced control ordered last visit. Tested unit.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ11
Near Monument, CO 80132
Eric
Job Details:
05/06/2024
"Found rails binding replaced, freezer door opens smoothly. Tilted unit and verified base pan. Did not change base plate as fan noise has no longer happened since last visit as customer stated. Customer will monitor and report if it returns."
We serviced a
ROPER DRYER
Model RGD4516FW0
Near Pueblo, CO 81004
James
Job Details:
05/06/2024
Installed ordered part. Tested ops all ckok advised cust to have licensed vent cleaning service to address slight restriction
We serviced a
THERMADOR RANGE
Model PRG486WDG/06
Near Edwards, CO 81632
Erik
Job Details:
05/06/2024
xlo burners working as designed - timed restarts are to be expected when turning the knobs to LO or XLOcheck voltage to burners: GOOD - no action requiredJOB COMPLETECX is aware of XLO feature/ CX not available for signature
We serviced a
GE WASHER
Model GFW650SPN0SN
Near Gypsum, CO 81637
Erik
Job Details:
05/06/2024
install part/ connect to smartHQ service:perform load test on new part: PASS * see quick picsapply firmware update - test: GOODCX not available for signatureJOB COMPLETE
We serviced a
KITCHENAID REFRIGERATOR
Model KBFS22EWMS7
Near Los Lunas, NM 87031
Larry
Job Details:
05/03/2024
CX complaint - Ive forming on bottom of freezer - Inspected unit and found the drain in back was colgged causing ice to build up during defrost - Cleared ice and drain - Unit is good to go - PIF-Auth-99HC3H
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Los Lunas, NM 87031
Larry
Job Details:
05/03/2024
Installed Im and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS3
Near Colorado Springs, CO 80924
Aaron
Job Details:
05/03/2024
"Heating element and thermostat are shorted out, removed and replaced components, tested unit through diagnostics and verified power to heating element, working well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID WALLOVEN
Model KODE300ESS21
Near Colorado Springs, CO 80924
Aaron
Job Details:
05/03/2024
"Oven door gasket is coming apart, removed and replaced gasket, working well now. Verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL RANGE
Model WGG745S0FS02
Near Colorado Springs, CO 80908
Aaron
Job Details:
05/03/2024
"Both cavity bake ignitor are shorted out, removed and replaced components, tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Frisco, CO 80443
Erik
Job Details:
05/03/2024
hose drain inlet WH41X10280 was NOT attached to tub *see quick picsreattach hose and test: GOOD(no leak) JOB COMPLETEextensive damage to lower level doors/ door frames/ door jams *see quick picscall GE TAG: report damage caused by drain hose inlet malfunction case#12940735CX aware and not available for signature
We serviced a
SAMSUNG MICRWAVE
Model MC17T8000CG/AA
Near Colorado Springs, CO 80925
Mathew
Job Details:
05/03/2024
"Replace broken fan, motor and housing. Test op all okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAEWWAA
Near Fountain, CO 80817
Mathew
Job Details:
05/03/2024
"Found ice room frozen, thawed and dried room, sealed ice room. Installed y clips and retainer. Replaced control. Test op all okay."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Colorado Springs, CO 80921
Aaron
Job Details:
05/03/2024
"Heating element connection loose, corrected and tested, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HDEDBSR/AA
Near Manitou Springs, CO 80829
Mathew
Job Details:
05/03/2024
"Found ice room frozen, defrosted room. Replaced icemaker, installed ice maker service kit, sealed room. Replaced control. Test op all okay."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Pueblo West, CO 81007
Ralph
Job Details:
05/03/2024
installed parts and unit checked okay
We serviced a
GE FREEZER
Model FUF14DLRDWW
Near Breckenridge, CO 80424
Erik
Job Details:
05/03/2024
install final union - charge unitholding pressure and cooling resumes after 10 min of chargingJOB COMPLETECX not available for signature
We serviced a
AMANA REFRIGERATOR
Model ASD2624HES
Near Colorado Springs, CO 80905
Carlos
Job Details:
05/03/2024
"Installed defrost heater and thermostat, Cx will observe. Cx paid Labor"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Colorado Springs, CO 80906
Carlos
Job Details:
05/03/2024
"Installed blower, kit and motor all ok"
We serviced a
MAYTAG RANGE
Model MER8700DS1
Near Fountain, CO 80817
Carlos
Job Details:
05/03/2024
"Installed pan, broil and bake ran test all ok. Cx paid Labor $189.95 CC Auth# 9VCFC9"
We serviced a
AMANA DRYER
Model NED4655EW1
Near Black Forest, CO 80908
Carlos
Job Details:
05/03/2024
"Ran test, issue lies in wall outlet. Only has 120VAC needs an electrician to repair outlet."
We serviced a
SAMSUNG DRYER
Model DVES2N17750W/A3
Near Pueblo West, CO 81007
Domingo
Job Details:
05/03/2024
Check support rollers and they are bad needs themSC 129.95Needs rollers but customer decided that he wanted to buy a new one so just charge for Service call customer paid $129.95
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FMDM10
Near Black Forest, CO 80908
Carlos
Job Details:
05/03/2024
Unclogged the fill tub for ice maker all ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF736SDAM11
Near Colorado Springs, CO 80922
Aaron
Job Details:
05/03/2024
"FC evaporator fan motor bearings are worn and loud, unit is cooling well at time of inspection, cleared hair from condenser, needs evaporator fan motor. Approved onsite. Removed and replaced component, working well now. Needs time to cool. Evap fan motor wpw10514110 $314.22Tax $25.77Supplies $14.50Hc $149.95Labor $209.95Total job $714.39 No return on partsPaid cash total job $714.49"
We serviced a
AMANA RANGE
Model AGR6303MMW0
Near Ordway, CO 81063
James
Job Details:
05/03/2024
Complaint of unit tripping breaker on initial pkyg in. Could not test unit fully due to no gas hookups. Did test entire electrical system no ground shorts or unusual Amp draw readings. All readings normal.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Rocky Ford, CO 81067
James
Job Details:
05/03/2024
Found loose wire at drain pump causing no drain secured wire and tested all ops test good. Left litmus.
We serviced a
PROFILE WASHER
Model PTW700BPT0DG
Near Leadville, CO 80461
Antonio
Job Details:
05/03/2024
Installed acu call rech line to program could not test properly sence unit is sitting out side on deck
We serviced a
SAMSUNG RANGE
Model NX58H5600SS
Near Colorado Springs, CO 80905
Mathew
Job Details:
05/03/2024
Replaced broken igniter. Test op all okay.
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW012
Near Rio Rancho, NM 87124
Joe
Job Details:
05/03/2024
"Cx complaint. Lights dim when washer is in agitation. Replaced clutch, rotor and stator ordered last visit. Checked unit and got same amp range. Talked to tech support. Sr# 7739018351. Per tech support, owners manual states washer should be on a dedicated circuit. Washer working as designed"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS05
Near Monument, CO 80132
Eric
Job Details:
05/03/2024
Replaced failed ice maker and tested via diagnostics. Unit now working properly. Informed customer of survey.
We serviced a
MAYTAG WASHER
Model MVWB850YW0
Near Colorado Springs, CO 80920
Roman
Job Details:
05/03/2024
Removed the old dispenser and installed new one. Tested the washer and no more leaks. Washer working great. Paid labor check $169.95 CK Auth# KXR3F9
We serviced a
ASKO DISHWASHER
Model DF1664
Near Colorado Springs, CO 80921
Roman
Job Details:
05/03/2024
Tried testing the dw but the door is damaged on the left side hinge. Screw is missing and looks like the side panel wher the acre sits is broken. Cx did not want to put too much more money into the unit. I put in a a large long screw to hold it in-place. Adjusted the led to sit properly and not on the ground. Tested the unit and the door is opening and closing properly. Checked for leaks. Dw working great. Labor $220.00Sc $149.95Total cost $ 369.95$369.95 CC Auth# 399MV3
We serviced a
WHIRLPOOL WASHER
Model MVWP575GW0
Near Colorado Springs, CO 80919
Eric
Job Details:
05/03/2024
"Found securing bolt pulled out, reinstalled and tightened down. This bolt has worked its way loose and will happen again, informed customer and she is aware that this will happen since washer needs a new agitator, also informed customer that because we are not putting in a new one we will not be coming back to repair this issue again for free."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Colorado Springs, CO 80918
David
Job Details:
05/03/2024
"Replaced UI and freezer bin. Tested operation, all working as expected."
We serviced a
GE DRYER
Model GFT14ESSM0WW
Near Colorado Springs, CO 80907
David
Job Details:
05/03/2024
"Replaced heater assembly, tested and is heating up good."
We serviced a
HOTPOINT WASHER
Model HTW240ASK6WS
Near Colorado Springs, CO 80922
David
Job Details:
05/03/2024
"Replaced gear case, pully, clutch, belt, and suspension rods. Ran test cycle, all running good."
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Belen, NM 87002
Larry
Job Details:
05/03/2024
Installed valve and tested good - Unit is good to go
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Albuquerque, NM 87111
Jason
Job Details:
05/03/2024
installed module kit
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Albuquerque, NM 87122
Jason
Job Details:
05/03/2024
Installed parts unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW5100HW3
Near Albuquerque, NM 87106
Jason
Job Details:
05/03/2024
installed valve unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Albuquerque, NM 87123
Jason
Job Details:
05/03/2024
nstalled parts unit checks ok
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Edgewood, NM 87015
Jason
Job Details:
05/03/2024
Installed parts listed unit checks ok
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ1
Near Grand Junction, CO 81506
James R
Job Details:
05/03/2024
"customer sighned disclaimer . left hand adjuster damaged , another had to ordered in .replace docking retainers and adjusters on second and third shelves, run unit to verify operation. install leak board . all good . job complete.please fill out whirlpool tech satisfaction survey.Thank You."
We serviced a
WHIRLPOOL WASHER
Model MVW7230HW1
Near Fruita, CO 81521
James R
Job Details:
05/03/2024
Customer signed disclaimer. Rubbed finger on edge of tub there is some white powder residue. Put on a quick wash. No soap in dispenser. Let fill then agitate soap suds started to form. Light not heavy. Cusomer needs to do a cleaning of unit with Affresh at least once a month. Depends on usage. Also be mindful of how much soap is being used too much wilol cause the residue. They have no wtr sofener. Also put pods in the unit first before cloths. Called tech line to confirm recommedations. SR# 7739019782 Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Fruita, CO 81521
James R
Job Details:
05/03/2024
cusdtomer did sighn disclaimer.replaced gear case and rotor.run unit through diagnostic cycle.no error codes present.all good job complete. It is normal for these units to make a thumping noise due to the drain tube moving during spin. unbalanced load is often a larg contributeing factor for noise. Will also hear some noise just due to the normal vibration of the unit. please fill out whirlpool tech satisfaction survey.Thank You.
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Colorado Springs, CO 80919
Jerimiah
Job Details:
05/03/2024
"Installed replacement parts, found TCO and TCO wires melted on top back of mw. Repaired. Microwave heats food, but some reason pops a bag of popcorn in cycled. It pops, then stops and deflates, started heating again then deflates. Called techline said popcorn may not have enough moisture causing mag to overheat and inverter to lose lower, recommended to add a cup of water to mw to facilitate humidity. Unit check ok."