Service History 132 - D3 Appliance

We serviced a

SAMSUNG DRYER

Model DVE55A7700V/A3

Near Colorado Springs, CO 80922

Brandon

Job Details: 11/13/2023

"Bad thermostat, replaced heater assy and tested op all ok hass passed"

We serviced a

WHIRLPOOL BEVERAGE COOLER

Model KUDF204KPA00

Near Colorado Springs, CO 80919

Kris

Job Details: 11/13/2023

7737144523 called techline unit is not level needs to be pulled out from cabinet no airflow. cx asked to turn down temp and try that first.

We serviced a

SAMSUNG RESIDENTIAL REFR

Model RF28R7351SG/AA

Near Colorado Springs, CO 80925

Mathew

Job Details: 11/13/2023

"Completed service bulletin, test op all okay. Icemaker running."

We serviced a

KITCHENAID DISHWASHER

Model KDTE404DSS0

Near Colorado Springs, CO 80919

Kris

Job Details: 11/13/2023

found plastic in drain pump impeller ran tst op all ok unit is working to spec at this time.

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS1

Near Falcon, CO 80831

Aaron

Job Details: 11/13/2023

"Right door hinge not properly engaged to door spring, corrected and tested, unit and door are working well now. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHW00

Near Elbert, CO 80106

Aaron

Job Details: 11/13/2023

"Customer settings upon arrival 0f FC, 36f RCTop shelf 36.9Second shelf 38.4fCrisper 39.4fFreezer -2.1 product temps at time of inspection, discussed situation with techline, setting FC to 1f and RC to 38f, sending picture of product loading in RC, thermistors pass to specs. Cleaned condenser of debris, both doors are sealing well. SR7737223447. Advised customer of situation and survey."

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Colorado Springs, CO 80904

Carlos

Job Details: 11/13/2023

Installed door all ok

We serviced a

WHIRLPOOL WASHER

Model WTW8000BW0

Near Colorado Springs, CO 80921

Jessie

Job Details: 11/13/2023

Unit has been sitting for a while. Pulled off back panel and inspected the unit for leaks. Unit did have bugs. Cleared out debris and ran hit water and vinegar. All operations are good. All ok

We serviced a

GE DRYER

Model GTD42EASJ2WW

Near Colorado Springs, CO 80910

David

Job Details: 11/13/2023

Replaced wire harness and heater Tested and timer is advancing

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAHZ0

Near Grand Junction, CO 81503

James R

Job Details: 11/13/2023

Test run unit in dignostics there are no error codes. Checked water temp from tap 120 degrees good not too hot. Let run thru a cycle while working on dryer. Did not leak. At this time no repairs needed. Customer paid service call . $99.00 auth code 3Y9K9J

We serviced a

GENERAL ELECTRIC WASHER

Model GTW465ASN9WW

Near Colorado Springs, CO 80906

David

Job Details: 11/13/2023

"Replaced inner basket, wash plate, and auger Tested and running great"

We serviced a

KENMORE WASHER

Model n/a

Near Pueblo, CO 81001

James

Job Details: 11/13/2023

"found unit with a major leak causing damage to multiple componets under unit. unit needs multiple parts, seals, motor, gc clutch and support. support is discontinued unit will not be repairable. cust stated that they have replacement policy. advised if that is the case xcel will be contacting them in approx 48 hrs to discuss next steps"

We serviced a

BOSCH DISHWASHER

Model n/a

Near Colorado Springs, CO 80906

Ralph

Job Details: 11/13/2023

"INSPECTED AND TESTED UNIT, UNIT WORKING CORRECTLY...autho no.9NHR94"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ00

Near Colorado Springs, CO 80924

Aaron

Job Details: 11/13/2023

"Evaporator fan motor is not coming on during diagnostics test 3, air baffle is working, cold air from FC is not able to cool RC properly, ice dispenser flap is broken, sold as an assembly. Evap fan motor w11224591 $142.12Dispenser wpw10577864 $120.02Total parts $262.14Tax $21.50Supplies $14.50Hc $129.95Labor $229.95Total job $658.0430 day estimateNo return on partsAuth 129.95 hc #CXX3C3"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF535SMHZ07

Near Colorado Springs, CO 80924

Aaron

Job Details: 11/13/2023

"Endcap tab broken, cover missing, rest of unit is working well. Removed and replaced components, working well now. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SMHZ03

Near Colorado Springs, CO 80917

Kris

Job Details: 11/13/2023

installed compressor chraged with 48 grams of r600. ran test op all ok unit is working to spec at this time.

We serviced a

BOSCH DISHWASHER

Model SHX68T55UC/07

Near Pueblo, CO 81005

James

Job Details: 11/13/2023

checked unit out. all ops ckok. advised cust to use affresh to help with very light smell. all other ops ckok collected 149.95 via ck $149.95 CK Auth# F4443L

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS1

Near Colorado Springs, CO 80921

Glenn

Job Details: 11/13/2023

"Found bad Neutral connection at Junction block. (Melted wire). Block apears to be ok, Fuse >ok, Install new UI Control. All OPS Test:OK"

We serviced a

WHIRLPOOL DRYER

Model WFW5090GW0

Near Grand Junction, CO 81503

James R

Job Details: 11/13/2023

Evaporator condenser plugged had to tear completely apart. Cleaned. Reassembled. Run unit it is heating. Customer paid service call $149.95 auth code K3P443signed waiver.Please fill ouit whirlpool techj satisfaction survey. Thank You.

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Grand Junction, CO 81507

James R

Job Details: 11/13/2023

"Checked air flow with test kit W11224254 Ran for 3 times air dry timed dry. Card fell off everytime. So it appears that vent is clear should not be affecting the dry cycle. In diagnostics does not show any error codes. Put in several towels. Wet. Unit is sensing now drying. Did notice that the towels werent touching as much as should. Lowered front of dryer. They are now touching the sensors more consistent. Time in the display will drop and then go back up depending on the dampness it senses the towels. It is working as it should. Customer needs to be aware to dry like cloths. sheets,linens will dry faster than a heavier material. These items may still be damp. Unit has continued to run has not shut off prematurely with time in the display. Put unit on timed dry ok"

We serviced a

WHIRLPOOL WASHER

Model MVW6200KW2

Near Grand Junction, CO 81501

James R

Job Details: 11/13/2023

Put into drain and spin. Unit would just hum.Tilted back removed pulley cover. Replaced capacitor. W11395618 Reassembled and test cycled in diagnostics operation is normal. customer paid $301.19 auth code A9K43Ksiged waiver.Please fill out whirlpool tech satisfaction survey. Thank You.; used 1 W11395618 (Capacitor) from stock

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT518SZFM02

Near Grand Junction, CO 81504

James R

Job Details: 11/13/2023

Cycled icemaker. water went into tray. Removed icemaker. Full tube extension was too far in. Extended it out to go into chute of the icemaker. Cycled icemaker a couple of times to confirm proper operation. Normal ok.Customer signed waiver. Please fill out whirlpool tech satisfaction survey.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ05

Near Pueblo West, CO 81007

James

Job Details: 11/13/2023

installed ordered parts all ops test good

We serviced a

KITCHENAID DISHWASHER

Model KDTE304LPA1

Near Eagle, CO 81631

Antonio

Job Details: 11/13/2023

Installed new acu and sump unit tested good also advised cx of water srips

We serviced a

GENERAL ELECTRIC DRYER ELECTRIC

Model GFD14ESSN1WW

Near Carbondale, CO 81623

Erik

Job Details: 11/13/2023

install/test: GOODJOB COMPLETE

We serviced a

ROPER DRYER

Model RED4516FW

Near Eagle, CO 81631

Antonio

Job Details: 11/13/2023

Installed new heat element and cutoff

We serviced a

MAYTAG DRYER

Model MED4500MW0

Near Albuquerque, NM 87110

Jason

Job Details: 11/13/2023

checked unit found loose wire connection to element. repaired connection unit checks ok

We serviced a

KITCHENAID WALLOVEN

Model KOCE500ESS22

Near Albuquerque, NM 87111

Jason

Job Details: 11/13/2023

installed part unit checks ok

We serviced a

MONOGRAM REFRIGERATOR

Model ZIW303NPPBII

Near Carbondale, CO 81623

Erik

Job Details: 11/13/2023

"safety switch on IM asm stuck in 'off' position - ice scoop in ice bucket when full jams in the sensor bar, not allowing it to return to empty position even when cleared of iceremove scoop from bcket and dislodge the IM asm ad test: GOODeducate CX on clearing obstructions from EXTREMELY small freezer drawerJOB COMPLETE"

We serviced a

AMANA DRYER

Model NED4655EW1

Near Albuquerque, NM 87121

Larry

Job Details: 11/13/2023

CX complaint - Dryer not heating - Inspected unit and found TCO and heater open - Replaced with pre-id parts and tested gooed - UInit is good to go

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ08

Near Albuquerque, NM 87120

Larry

Job Details: 11/13/2023

Cx complaint - Not making ice - Installed pre-id parts and tested good

We serviced a

MAYTAG WASHER

Model MVW5430MW0

Near Rio Rancho, NM 87144

Larry

Job Details: 11/13/2023

Installed control and tested good - Unit is good to go

We serviced a

WHIRLPOOL WASHER

Model MVWB766FW1

Near Rio Rancho, NM 87124

Larry

Job Details: 11/13/2023

CX complaint - Cold water not working - Inspected unit and found debris in the cold valve - Cleaned valve and tested good - Unit is good to go

We serviced a

WHIRLPOOL M/W OTR

Model WMH78519LZ00

Near Colorado Springs, CO 80925

Carlos

Job Details: 11/13/2023

Installed wrapper and screws all ok. Cx needs to contact installer company for bottom bracket it was installed bent

We serviced a

GE MICROWAVE OVEN

Model JNM3163RJ5SS

Near Colorado Springs, CO 80906

David

Job Details: 11/13/2023

Replaced door latch partsTested and is working great

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ0

Near Grand Junction, CO 81504

James R

Job Details: 11/13/2023

"Put into service diagnostics. Has a FAE2 error code. Vent electrical issue. Removed outer panel checked electrical wiring from control to vent asy. Ok. Checked resistance of vent 1.4 K ohms is ok. Replaced control, T stat and heat element. Run thru a diagnostics after repairs . Is heating 7.1 amps good. No error codes when done. Unit is working as should. Called tech line. All checks checked good. Do suggest opening door once cycle is finished to also help help dry . Customer signed waiver. Please fill out survey. Thanks.Customer is using rinse aid. Need to use hi temp and heated dry to assure that unit gets really hot to help dry. Also ceramic,glass etc will hold heat to help dry. Anything of plastic will not dry well. Any divit that is in a cup,glass will not dry completely."

We serviced a

AMANA WASHER

Model NTW4605EW0

Near Colorado Springs, CO 80919

Glenn

Job Details: 11/13/2023

"Unit has bad gearcase, seal has been leaking and bearing is grinding during spin cycle. Suggest Replace gearcase, Shifter, Splutch & Belt. , Let customer know that unit could eventually start leaking more water. Gearcase - W11454741 $312.58 , Splutch / Cam Kit - W10721967 $72,82 , Belt - WPW10006384 $61.83 , Shifter - W10913953 $91.46 , Tax $44.17 , MPS $14.50 , Labor $249.95 , Declined Estimate, Paid SC fee of $129.95 , Autho#399RN9"

We serviced a

COVE DISHWASHER

Model DW2450

Near Colorado Springs, CO 80906

Ralph

Job Details: 11/13/2023

"installed part, and unit checked okay"

We serviced a

AMANA DRYER

Model NED4655EW0

Near Colorado Springs, CO 80919

Glenn

Job Details: 11/13/2023

"Reseat & Tighten all connections to Timer, Heater Circuit & Switches, All OPS Test:OK Slight restriction in vent system, however, unit is cycling. Suggest customer have vent system cleaned at least 1X per year."

We serviced a

WHIRLPOOL DISHWASHER

Model WDPA70SAMZ1

Near Colorado Springs, CO 80915

Carlos

Job Details: 11/13/2023

Installed drain pump and adjusted drain hose. Ran short cycle. Runs all ok. Left leak strip

We serviced a

MAYTAG REFRIGERATOR

Model MFI2569YEM0

Near Pueblo West, CO 81007

James

Job Details: 11/13/2023

"found cntl resetting after power surge unit is now working may need main cntl WPW10312695 267.50, sc 149.95, labor 149.95, mps 14.50. Total: 603.84/453.89, cust declined collected 149.95"

We serviced a

MAYTAG WASHER

Model MVW4505MW0

Near Albuquerque, NM 87105

Larry

Job Details: 11/13/2023

CX complaint - Washer leaking - Inspected unit and found the valve failed - Replaced with TS and tested good - Unit is good to go; used 1 W11513255 (Valve) from stock

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW2

Near Cedar Crest, NM 87008

Jason

Job Details: 11/13/2023

Installed control and calibrated unit. unit opperation checks ok

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Edwards, CO 81632

Antonio

Job Details: 11/13/2023

Installed new acu and pump motor unitvtested good

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT112CZJZ00

Near Vail, CO 81657

Antonio

Job Details: 11/13/2023

Found bad compressor unit is up for review sr#7737776416

We serviced a

TRUE REFRIGERATOR

Model TBB-3G

Near Colorado Springs, CO 80906

Ralph

Job Details: 11/13/2023

"unit has a locked comp, will need repalcement, cust thinking of replacing the unit...cust paid totla bill autho no. VK3M3U"

We serviced a

WHIRLPOOL M/W OTR

Model WMH53521HZ06

Near Colorado Springs, CO 80924

Aaron

Job Details: 11/10/2023

"Control relay burnt , light bulb shorted as well, replaced components and tested, working well now. Advised customer of 5 star survey."

We serviced a

MAYTAG WASHER

Model MHW6630HW0

Near Fruita, CO 81521

James R

Job Details: 11/10/2023

F9E1 error code long drain. Cleared error code. Removed front of washer. Removed water and then pump inspected looked ok reassembled unit and put thru diagnostics test clear code. Did test 12. At end when got ready to drain pump hummed. It is faulty. W11458345 Customer will replace washer. Customer paid $149.95 auth code. 399A3T

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB543CMJZ00

Near Colorado Springs, CO 80920

Aaron

Job Details: 11/10/2023

"Removed and replaced door assembly, no dents or scratches, verified by customer. Working well now. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB322DMBM03

Near Colorado Springs, CO 80909

Carlos

Job Details: 11/10/2023

Installed gasket all ok

We serviced a

WHIRLPOOL DRYER

Model WED72HEDW1

Near Colorado Springs, CO 80918

Aaron

Job Details: 11/10/2023

"Idler and rollers are worn and squeaking, removed and replaced, lubricated, and tested unit. Working and heating well now. Advised customer of 5 star survey."

We serviced a

GE WASHER

Model GFW850SPN5RS

Near Leadville, CO 80461

Erik

Job Details: 11/10/2023

shipping bolt still installed/ remove and test: wobblesflooring weak in rear left corner of laundry space - CX prop mgmt knows they need to reinforce the floor to correctconnect to smartHQ service: spin test after securing unit: PASSJOB COMPLETE

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Albuquerque, NM 87111

Jason

Job Details: 11/10/2023

installed basket unit checks ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHW08

Near Colorado Springs, CO 80915

Carlos

Job Details: 11/10/2023

Ran test op. Found ice build up on evaporator fan blade. Replaced fan motor and fan blade and cleared up ice. Ran test op all ok

We serviced a

WHIRLPOOL RANGE

Model SF362LXST0

Near Albuquerque, NM 87104

Larry

Job Details: 11/10/2023

CX complaint - Oven not heating - Inspected unit nad found the control is not sending a signal to the ignition system - Parts are NLA - Collected SC

We serviced a

WHIRLPOOL M/W OTR

Model KHMC1857WSS0

Near Albuquerque, NM 87108

Jason

Job Details: 11/10/2023

installed switches and fuse unit checks okAuth code:33P9LN$206.10

We serviced a

WHIRLPOOL DRYER

Model WED5010LW1

Near Albuquerque, NM 87120

Larry

Job Details: 11/10/2023

CX complaint - Not dryling - Inspected unit and found the vent run clogged - CX had already cleaned a huge amount of lint from the run but it is still failing for electric dryers - Advised cx to have vents cleaned

We serviced a

MAYTAG DRYER

Model MED6230HW0

Near Albuquerque, NM 87114

Larry

Job Details: 11/10/2023

Installed parts listed and tested goo - Unit is good to go

We serviced a

MAYTAG DRYER

Model MED4500MW0

Near Albuquerque, NM 87105

Jason

Job Details: 11/10/2023

installed timer and knob unit checks ok

We serviced a

SAMSUNG DISHWASHER

Model DW80R9950US/AA

Near Pueblo, CO 81005

Brandon

Job Details: 11/10/2023

"Ran hass got error 5c, replaced drain pump, tested op all checks ok hass passed"

We serviced a

SAMSUNG REFRIGERATOR

Model RF22KREDBSG/AA

Near Pueblo West, CO 81007

Brandon

Job Details: 11/10/2023

Replaced auger assy and tested op all ok hass passed

We serviced a

SAMSUNG REFRIGERATOR

Model RS27T5200SR/AA

Near Penrose, CO 81240

Brandon

Job Details: 11/10/2023

"Replaced evap cover, pcb and damper, tested op all checks ok hass passed"

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FFHT2021QW0

Near Pueblo, CO 81001

David

Job Details: 11/10/2023

Checked refrigerator Cleaned defrost drain

We serviced a

SAMSUNG REFRIGERATOR

Model RF265BEAESR/AA

Near Colorado Springs, CO 80923

Glenn

Job Details: 11/10/2023

"Defrost Ice buildup, Install Ice room kit, Auger Motor Assy, Adjust fill tube. Corner already sealed from prior repair. Cycle Test IM, Fill > OK, All OPS Test OK."

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF577KPS02

Near Colorado Springs, CO 80919

Glenn

Job Details: 11/10/2023

Install New Damper in FF. All OPS Test:OK

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS1

Near Colorado Springs, CO 80919

Glenn

Job Details: 11/10/2023

"Error Code 8-4 : Overfill/Float Switch Open , Found water in drip tray. Empty tray, Reseat connections to PCB, Ran Diagnostics 3X, No Leaks. Did see foam inside unit. added half cap of wesson oil into tub, to rid foam. All OPS Test:OK, No Leaks, Adjusted front legs a little bit to provide better pitch. Suggest stop using PODS w/ rinse aid, and use liquid detergent, until all dispenser rinse aid is empty. Customer will continue to monitor."

We serviced a

KITCHENAID DISHWASHER

Model KDFE104DSS3

Near Colorado Springs, CO 80921

Glenn

Job Details: 11/10/2023

"sounded like something was hitting in wash cycle. Unit has always continued to work, but customer turned off breaker for safety. All OPS Test:OK, No weird sounds or noises. Ran Diag Cycle 2X. Possibly loading issue caused noise when it occurred for cutomer. Did find a small shard of glass in bottom of tub. Had customer clean screen & filter. Customer will continue to monitor and call back if needed. Paid SC fee of $129.95, Autho#W33C3T"

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS1

Near Colorado Springs, CO 80921

Glenn

Job Details: 11/10/2023

"Marcone was inncorrect, part did not come with screws needed. Had to go to hardware store to obtain a replacement screw & washer. Installed New Rack holders and Screw w/ washer obtained from hardware store. All OPS Test:OK"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ08

Near Monument, CO 80132

Glenn

Job Details: 11/10/2023

"Compressor, Evap Fan & Condensor fan motors running. Unable to determine any noise that is out of the ordinary.Techline: Comprerssor drawing .68amp > OK , Adjusted coolant lines around compressor & used cardboard to tighten cardboard panel under unit, in case vibration noises from it. Suggest customer attempt to record sound next time it occurs. Also, did not find any styrofoam in Dispenser chute, possible foam left over from shipping of unit? No Foam incorporated in design of unit, as far as I can tell. If problem returns, suggest send a different technician for 2nd opinion.SR#7737766774"

We serviced a

WHIRLPOOL M/W OTR

Model WMH78019HZ05

Near Los Lunas, NM 87031

Larry

Job Details: 11/10/2023

CX complaint - Humming noise when fan is on - Inspected unit and found packing material in MW cabinet - Removed and tested good - Unit is operating as designed

We serviced a

MAYTAG WASHER

Model MVWC565FW

Near Colorado Springs, CO 80907

Roman

Job Details: 11/10/2023

Cx wondering why theres not that much water. Explained to her that you have to fill the tub with more clothes to have it fill up more and explained which cycles to use for the amount of clothing.

We serviced a

GE REFRIGERATOR/TOP

Model FUF21QRRAWW

Near Colorado Springs, CO 80906

Roman

Job Details: 11/10/2023

Installed new door gasket and door is opening easier.

We serviced a

ASKO DISHWASHER

Model D5656XXLHS

Near Colorado Springs, CO 80906

Roman

Job Details: 11/10/2023

"Pulled the dw out and the float is touching the switch to the leak sensor. Dw leaking from the divider. Recommend replacing the divider, inlet valve and float. Valve #434374. $115.00Divider #700497 $159.00Float #700354 $72.50Tax $28.41Total parts $ 374.91MPs $14.50Labor $449.95Sc $149.95Total cost $989.31 Paid sc $149.95 CC Auth# F9JC33"

We serviced a

BOSCH DISHWASHER

Model SHPM78Z55N/22

Near Colorado Springs, CO 80906

Roman

Job Details: 11/10/2023

Ran dw through the diagnostic mode and its went through all the cycles without error codes. Noticed that the water was taking a long time to drain out. Checked the drain line and it was a mess so removed the drain line and attached it onto the disposal. Tested the dw and it drained out way faster and working great. Checked under neath it for leaks and checked the drain pump drain pump looks fine and had nothing stuck in it. Dw working great.

We serviced a

SAMSUNG REFRIGERATOR

Model RF28K9070SG/AA

Near Colorado Springs, CO 80908

Mathew

Job Details: 11/10/2023

Replaced icemaker parts. Test op all okay.

We serviced a

GE REFRIGERATOR/TOP

Model PYE22KYNIFS

Near Colorado Springs, CO 80906

Roman

Job Details: 11/10/2023

"Checked the ice bin and dispenser and the fridge is still freezing the lines. Added some styrofoam foam and raised the temps in the fridge. Did not use the new gasket, old one is sealing great after using vasaline on it."

We serviced a

GENERAL ELECTRIC MICROWAVE OVEN

Model RVM5160DH8WW

Near Colorado Springs, CO 80906

Roman

Job Details: 11/10/2023

"Checked the fan and it is not blowing out the front, pulled the microwave down and lipped the cooling fan. Tested the microwave and its blowing air out of the top vents. Microwave working great."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706EBS01

Near Pueblo, CO 81001

Kris

Job Details: 11/10/2023

cx is deciding on repairs fc temp@21.5 rc temp@33.1 unit has both evaps covered in ice will need listed parts. unit may have other issues. will need listed parts before i will know if unit needs additional parts.WPW10675033 control 267.45W11087438 fan 142.12 w11249952 142.12

We serviced a

GE WALL OVEN

Model CTD90FP2NS2S1

Near Colorado Springs, CO 80919

Kris

Job Details: 11/10/2023

installed fans. unit has a vibrating sound from they way the pannels are built. showed cx video of back of unit with all screws installed unit makes loud sounds when touching pannels. vibrating when units cooling fan is on.

We serviced a

SAMSUNG REFRIGERATOR

Model RB215BSSB

Near Colorado Springs, CO 80911

Roman

Job Details: 11/10/2023

"Checked the fresh food and it seems to be cooling okay. Freezer section is at 49 degrees. Checked the compressor and its pulling 16 amps indicating it is failing. And very hot to the touch. Condenser fan motor is not running but getting volts to it and the fan blade is completely broken. Recommend replacing the compressor, fan motor and fan blade .Compressor #N/AFan motor # N/AFan blade #N/AParts are not available for this fridge and none repairable."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ

Near Colorado Springs, CO 80925

Carlos

Job Details: 11/10/2023

"Installed compressor and charged. Low side pressure -1, high side pressure 95."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHB01

Near Pueblo West, CO 81007

David

Job Details: 11/10/2023

Replaced icemaker Icemaker filled with water

We serviced a

WHIRLPOOL WASHER

Model MHW5630HC2

Near Pueblo, CO 81005

David

Job Details: 11/10/2023

Checked washer Cold water valve 1 not flowing good Ck thinking about repairs Service fee of 149.95 good for 30 days

We serviced a

ELECTROLUX DRYER ELECTRIC

Model EIMED60LT3I

Near Colorado Springs, CO 80921

Kris

Job Details: 11/10/2023

cx is deciding on repairsblower 246.70 134690800motor 307.50 5304529782rollers x4 119.38 5304523155idler 79.18 134793511

We serviced a

SAMSUNG ELECTRIC OVEN

Model NQ70M7770DG/AA

Near Peyton, CO 80831

Jerimiah

Job Details: 11/10/2023

"Installed replacement components, unit check ok checked unit 30 times, (Cust watched), there was one failure, where high voltage did not kick on, plus unit did pop once but could not find where that was located. Closing call"

We serviced a

THERMADOR VENT HOODS

Model HII8057U/03

Near Breckenridge, CO 80424

Erik

Job Details: 11/10/2023

NOT THERMADOR PRODUCT**CX to call mountain high appliance for warranty**cancel service unless dispacthed by manufacturer or MHA

We serviced a

SAMSUNG GAS RANGE

Model NX60A6511SS/AA

Near Yoder, CO 80864

Jerimiah

Job Details: 11/10/2023

"Installed replacement parts, verified plunger was in up or on position of valve regulator. Unit check ok."

We serviced a

DACOR OVEN

Model ERD30S06BK/H

Near Colorado Springs, CO 80920

Jerimiah

Job Details: 11/10/2023

"Control dead and hinges sprung needs replacing, found both parts are NLA, charging service call. $172.44 CC Auth# 43MJ4U92028 controller 62436 hinge x2"

We serviced a

WHIRLPOOL RANGE

Model GR448LXPS0

Near Colorado Springs, CO 80904

Carlos

Job Details: 11/10/2023

"Ran test op. Broil relay on control board opens intermittently. Needs a new board (9757271) part is discontinued, can be sent out for repair. Cx will not repair. Cx paid SC $149.95 CC Auth# F4C449"

We serviced a

GE MICROWAVE

Model JKP90SP3SS

Near Manitou Springs, CO 80829

Ralph

Job Details: 11/10/2023

installed part and unit checked okay

We serviced a

KITCHENAID MICROWAVE

Model KMBP100ESS01

Near Colorado Springs, CO 80919

Carlos

Job Details: 11/10/2023

Ran test op. Microwave was stuck in demo mode. Turn off demo mode runs all ok Cx paid SC $129.95 CC Auth# UY4K34

We serviced a

SAMSUNG REFRIGERATOR

Model RF29A9771SG/AA

Near Colorado Springs, CO 80909

Mathew

Job Details: 11/10/2023

"Found installer severed cable on bottom right door. Will need new door. Called tech line. Samsung is not covering repair, deemed physical damage. DA93-00934G part."

We serviced a

SAMSUNG MICROWAVE

Model ME21M706BAS/AA

Near Colorado Springs, CO 80909

Mathew

Job Details: 11/10/2023

"Called tech line about walls of microwave being discolored, ticking noise coming unit while running. Tech-Line states Cx will have to open another ticket about discoloration. Microwave heated up water efficiently."

We serviced a

GE REFRIGERATOR

Model GSS25IYNXHFS

Near Pueblo, CO 81003

David

Job Details: 11/10/2023

"Checked refrigerator A little rattle from the compressor area Repositioned a couple of lines a little, no more rattle. Everything working normal"

We serviced a

GE REFRIGERATOR/TOP

Model GFE28GYNJFS

Near Breckenridge, CO 80424

Erik

Job Details: 11/10/2023

connect to smartHQ service: *see quick pics**NO ERROR CODES ACTIVE**abnormal defrost 1st cycle extended 15 min. (cause unknown) melted ice in bin and melted through port hole (all other plumbing inspected for leaks - none found)Ica maker test confrims ice maker asm working correctly - no leakspaddle dispenser checked with internal panel removed to inspect water tank and valve - no leaksNO ACTION REQUIRED AT THIS TIME

We serviced a

GENERAL ELECTRIC DISHWASHER

Model PDT755SYR5FS

Near Breckenridge, CO 80424

Erik

Job Details: 11/10/2023

installed/tested with clear door: PASS all cycles all zones

We serviced a

WHIRLPOOL WASHER

Model MVW6230HC3

Near Colorado Springs, CO 80908

Aaron

Job Details: 11/10/2023

"Gearcase making noise during cycle, removed and replaced gearcase, pulley, and belt. Working well now. Lifted front legs and verified level. Advised customer of 5 star survey."

We serviced a

MAYTAG WASHER

Model MVWE655DW1

Near Colorado Springs, CO 80908

Aaron

Job Details: 11/10/2023

"Gearcase leaking, gears are stuck in spin, entire tub rotating during agitation, motor and belt are burning, drive block is wearing as well. Discussed with customer, no estimate needed, they are purchasing new. Auth 129.95 hc #4LR4VH"

We serviced a

WHIRLPOOL DRYER

Model WED4850HW0

Near Colorado Springs, CO 80922

Aaron

Job Details: 11/09/2023

"Line loose at terminal block, shorted and melted wire and terminal, replaced terminal block and wires, customer unavailable to advise of survey or obtain signature."

We serviced a

WHIRLPOOL DRYER

Model MED3500FW0

Near Colorado Springs, CO 80919

Carlos

Job Details: 11/09/2023

"Installed idler pulley, ran test op all ok. Cx paid"