Installed ordered parts tested ops all ckok

"Replaced control, ran calibration and diagnostic cycles, all good"

Replaced components and cycled icemaker ok. All now checks ok. Flakes of ice in container are normal for flex tray icemaker. RK

Installed control ran calibration and quick wash cycle unit opperation checks ok. spoke to cx about review

Installed condensor and dryer. charged unit back up. pressures and heat exchange check ok. spoke to cx about review

Silverware basket rubbing on right side of tub due to bent lower rack. Straightened rack and sliding freely without rubbing.

"Replaced control, ran calibration and diagnostic cycles, all good"

Installed parts

Customer signed disclaimer and recieved parts ordered agitator.intalled new agitator and noticed in rinse there was no water checked the hoses and they hot and cold were mixed up.Changed hoses around tested unit for leaks and spin it ran properly. PLEASE TAKE TECH SURVEY THANKS.CLINT.

Verified information customer signed disclaimer.Turned off power and pulled the unit out. Removed the touch display and installed the new display.Restored power and tested the unit tested good.Operating as designed by factory.Thank youIf you are satisfied with the service I have provided you with today then please share your experience with others and fill out a technician survey @ D-3 A-OK Appliance service inc.Your technician.Sean ....

Customer returned the unit to Lowe's and replaced the unit Picked up the Parts.

Installed the lightTested unit good.

"Replaced controls board , ran calibration, and automatic test cycles ok. All now working properly. RK"

No leaks found at this time Suds in unit with no soap added Customer instruct about soap usage and loading techniques Door gaskets and spray arms all look good Tested and saw zero leaksAdvised of survey

Tub glides had come off of upper bulkhead and grinded down to plastic And grinded tub Replaced and tested Advised of survey

"Customer recieved parts ordered...pump assembly. Installed pump rannunit on quick cycle,it filled agitating properly and drained."

Signed disclaimer. Put unit into service test 40 3 way valve shifts ok. Compressor comes on remove cover over compressor area. Put a valve BPV 31 on service port pressure on low side is 50 psi so the compressor is shot. Unit is beyond the 5 year warranty. So has no coverage. Customer will replace unit Customer paid service call $229.95 auth code NPE4C9

I installed the control board unit is operating properly at this time

I installed the hinges unit is operating properly at this time

Installed pre-ordered part per service flash tested ops all ckok. Discussed survey

During repair found gc siezed to basket. Tried every trick in the book to free. Could not. Called assurant. They are deeming unrepairable will contact cust in 48-72 business hours.

KINK IN DRAIN LINEJOB COMPLETE

Clean up he evaporator test it told cx to put clothes and see how it does but if problem persist it will need evaporator assembly and i will need help 4 hours and the part number would be evap ADJ75622509

"Fridge 38, freezer 6, plastic bag blocking fan in freezer, fans working with no noises, unable to verify noise, back panel and condenser coil blocked with lint. Clean condenser and panel, customer to monitor. Service fee $149.95, Labor $120.95, Total $270.90, paid autho WA3YP3"

"Shocks all connected, no play in basket, ran high speed spin, no noise from bearings. Unit level, has floor drain and sloped floor. Advised on washing by weight of absorbency."

Customers complaint middle spray arm fell i reinstalled it unit is operating properly.At this time

Uninstall the door latch and tested unit operating properly at this time

Unit working properly. Techline had me run several tests and said the problem is on the user end somewhere. Advised customer to replace flexible vent with semi-rigid or rigid duct. RK

Installed element and cut off runs all ok.

Upon arrival the lines on the compressor were frozen I decided to get Freon out de thaw evaporator and the. Put it on vacuum to 500 microns then charge it and no frost came in told cx to monitor a

Replaced sump/motor assembly. Ran tested okay with customer present. No leaks. Advised customer of survey

"Replaced controls , but during repairs also had to clean out spray tube above evaporator that was clogged and probally the issue. Waited for unit to dump a batch of ice. All checks ok RK"

The washer is working normally at this time. The customer is going to monitor it.

Replaced control board calibrated ran diagnostic and it passed

CX stated parts have been ordered already

The big oven is pretty close to temp. The small oven may be off because thermostat bulb is not in the proper place. Customer will correct once cool.

"Error 40c, replaced auger assy and ice maker, cycled all checks ok"

REPLACED CUST Water line that he purchased iunit checked okay...autho no. JL9K9H

"Inverter and magnetron are shorted out, removed and replaced components, tested unit, working and heating well now. Advised customer of situation and survey."

"F4E1 error code in diagnostics, metal support vibrating against blower housing, corrected and tested unit, working and heating well now. Advised customer of situation and survey."

Customer signed disclaimer. Unit is always saying to clean washer more than it should and is making a clicking noise.installed clutch and slider assembly the clicking noise did stop.PLEASE TAKE TECH SURVEY.THANK YOU.CLINT

"Replaced compressor, install dye drier and process stub. Pull into vacuum. Leak check, charge to spec. Monitor temps and pressures. All okay."

Customers complaint units not going through a cycle.I arrived and started the unit and it started right up so I rented into a quick diagnostic to test everything.Everything looks good unit is operating properly at this time

Replaced the control panel and tested.

Installed control board ran tests runs all ok.

Installed hose all ok

Installed control board runs all ok

"Found power to control, control not operating. Replace control. Test op, unit working as expected. All buttons working, cycle running fine."

Verified the unit information & customer signed disclaimer.Checked the unit and found it had an error 25 = door latch.Customer had a new latch.Installed the new door latch and reset the unit. Turned it on and checked the errors the unit had an error 95 = drain pump. Removed the kick plate and checked the drain pump Cleared out any obstructions. Reassembled the unit and reset the unit again.Started the unit . The unit went into quick wash door locked and the drain pump came on. The unit filled with water and started to run the cycle.Watched the unit complete the wash cycle Started a quick full wash.$239.95 SVF#229.95 LaborPaid Auth code JJA394

Installed kit all ok

Installed IM and tested good - Unit is good to go

Installed part ran quick cycle unit opperation checks ok. spoke to cx about review

Installed parts listed. ran quick dry cycle unit opperation checks ok. spoke to cx about review

Replaced dispenser. Ran tested okay no leaks. HASS passed. Advised customer of survey

Checked unit found soap looks to have been building up. Spoke to cx about running hot water before starting unit to aid in wash performance. unit opperation checks ok at this time. spoke to cx about review

Replaced rails and gasket. Customer will monitor

Replaced all parts listed. Customer will monitor

Installed both parts listed ran quick cycle unit opperation checks ok. spoke to cx about review

install door latch asm on sitetest: PASSJOB COMPLETESERVICE $284.95 PAID via iWallet autho# X43JU9

FD050604679MISSING EXTERIOR INSULATION JACKETCALL BSH TAG: NOT ON PARTS DIAGRAM - NONE ON UNITJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE

Checked unit found LR burner ignitor wire wasnt hooked up from factory. connected wire at spark module opperation checks ok. spoke to cx about review

"CX complaint - when trying to run, it says unable to fill water. no water trying to come into the - Inspected unit and found the valve failed - Replaced valve and tested good - Unit is good to go - Survey mentioned"

Installed bin holder.

"Control getting power but not powering anything else. Needs control board and maybe ui, quote in quick pics. Cx looking into getting new dishwasher."

Main board was not outputting power to drain pump Replaced tested and working Advised of survey

"No problems found, inspected blower housing and blower wheel along with both seals and even checked airflow to the outside and everything is checking okay at this moment in time. Customer is concerned about a potential fire so I took the top off to look for any excess lint or dust and everything went perfectly clean."

Verified information customer signed disclaimer.Checked the unit and determined that the belt has come off of the unit. Removed the top panel and the front top cover then the screws holding on the door panel.Removed the drum coller and the sir baffle.Put the belt back on the tensioner pulley and hooked the spring back up.Reassembled the unit. Tested the unit came on and ran drum is spinning good .Unit operating as designed by factory.

ACCESS MODEL HOMEFD0503 00410TEST: NORMAL FUNCTION - XLO IRIS WITH ADD EXTRA 'SNAP' TO IGNITION (FEEL AT KNOB) XLO SETTING WILL IGNITE/ EXTINGUISH AT SET INTERVALS AS DESIGNED - SEE OWNERS MANUALALL BURNERS WILL 'CLICK' TO IGNITEJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE

Replaced MC board due to voltage output error found with tech line Tested machineAdvised of survey

Replace door switch tested good.

"When I first arrived I found a red tag on top of the range from Cascade natural gas and it indicated that the gas was turned off at the stove because there is a gas leak at the appliance. I started by inspecting the bake igniter and it looked like it was in perfect shape so I fired up the oven and the igniter glowed perfectly and in less than 20 seconds to bake burner ignition occurs. I shut that off and tested again with the same results and I also checked the broil igniter and ended up with the same results on that. I did notice the remnants of a spill down near the burner, I took a picture of it, and I'm curious if that is what maybe the customer was smelling if that is the reason for the call. The oven is working perfectly fine so I called the gas company to get more information and they said the oven worked fine for them and after warm up the carbon monoxide readings spiked to 50 parts per million. When I reassembled the oven and tested it at 350?, I noticed at preheat PPM spiked to around 80 for just a few seconds and then started dropping back down to around 5 to 10 ppm. So I increased the temperature up to 450? to test it again and as the oven got hotter the higher the ppms got. But all I could smell is remnants of cooking. The PPM of carbon monoxide actually goes up once the burner is shut off. I left the oven operate for about 15 minutes at 450? and the smell started to reduce and parts per million of carbon monoxide dropped down to zero. No leaks of gas detected at this time. And I haven't appears to be working perfectly fine."

"Signed disclaimer. Replaced rail mullin and the trim bracket. Operating as designed, Please fill out tech satisfaction survey. Thank You."

Signed disclaimer. Removed control panel and replaced control. Test operation is working as designed. Checked all top burners ok. Pllease fill out tech satisfaction survey. Thank You.

"Repair gas leak on right side griddle solenoid , tested for gas leaks. Service fee$206.00, Labor $279.95, Total $485.95, paid autho J3LH3L"

Drain line was shoved down into drain pipe too far. Making drain pump work overtime. I pulled drain line out about 1 foot and secured it with a zip tie to water line. Unit is running good now.

Replaced heating element and both sensors tested unit. Heating up normally. CX not available for signature

Signed disclaimer. The Inspection door was bent had a time getting it open when did found that the switch under the cover was not being activated. Causing unit not to start adjusted the switch mounting bracket so it activates. Also made adjustments to the lock mechanism. Started unit after a few minutes started showing suds and timing down. Unit drained and reset and filled again and started over. Flushing out the soap is working. Also cleaned dispenser had lots of soap residue. Let unit go thru cycle to be sure is fuction as should. Spins drains ok. It is went thru and shut down. Suggest they use less soap. At this point unit is working as designed. Please fill out tech satisfaction. Thank You. Customer paid by check # 2299 Service call $269.95 auth code. WHTRN9

Unit needs user-interface Sc$355.95Pt$551.88 wh22x32062Lb$189.95Mpg$17.50Tt$1015.25Cx holding on repairs $255.95 CC Auth# WR4K43

"Replaced main control board, Paid labor $295.95 check #1156 autho X349MU"

Cycles oven to 450? and temps were spot on. Tested and all checks okay.

"Installed ordered parts, tested operation of fan icemaker, ran fill tested. All good."

Unit working fine excespt on auto dry. Customer needs to have vent cleaned al the way to the exterior of the house. RK149.95Auth ER9TL4

Replaced belt and unit is now working properly. RK

"Installed motor, board, thermistor and wheel all ok"

Replaced control board and the UI board. The customer is going to monitor it.

Installed control board. Sensor and hose.

Installed ordered parts tested ops all ckok. Discussed survey

"Installed new cntrl board, power board, and ui panels then cycled unit on and unit is working properly"

Pulled unit and checks all connections. Unit is working fine at this time. Signs of water at front insulation under door as unit had been oversudsing. Explained to customer how to properly run cleaning cycles. RK

"22228907, f4e3 wash motor fault, motor getting 120 but not working, need sump, $588.80 to repair, cx declined"

Sc 149.95 needs filter housing WP2225521 205.24 labor 199.95 MSRP 14.50 total 586.47 cx decline sc 149.95 cx paid see pic

Replaced thermistor and cx complaint that once the fan make a noise and they shake stove and it have not done it since I told cx that I check all that motor is fine and prob the stove was not align at the bottom told them to monitor that since didnt make the noise when I test it. I set it 350? and it reach 350? in a normal time manner at this Time Machine is fix

Adjusted units ventery then heated oven to 350? unit is working as designed

installed part and unit checked okay

Replaced control shifter drain pump test it and it passed I also level machine

Cx cancelled said they didnt think it had to pay

I found a nick in one of the wires so i replaced the harness and tested the unit is operating properly.At this time

CX BOUGHT NEW COFFEE MAKER - CANCEL APT

TUB CONTORTED IN OPENING - UNINSTALL AND CORRECT (LEVEL LEGS AND ADJUST METAL FRAME )REINSTALL UPPER WASH ARM ASM AND REINSTALL UNIT IN OPENING - TEST: PASSJOB COMPLETESENT CX BILL VIA iWALLET $234.95

Replaced element and tested