Service History 139 - D3 Appliance

We serviced a

KITCHENAID DISHWASHER

Model KDTM704LPA1

Near Colorado Springs, CO 80921

Jessie

Job Details: 01/31/2024

"Unit is draining very well. Found drain line semi kinked in the back. Repositioned drain line, found drain line connected to a reducer causing slow flow. Eliminated reducer and ran drain line to pipe and secured. Called techline to see if they have any known issues where customer has unit full of water in it. Talked with Brandon.no known isssues. Found slow drain error. Reducer defint could cause issue. Drains well and good 15-20 aeconds of dry drain.Sr#7738368570"

We serviced a

JENNAIR WALL OVEN

Model JJW8630DDS

Near Pueblo, CO 81006

Domingo

Job Details: 01/31/2024

Install sensor and safety switch check oven temp is getting to 300 and climbing

We serviced a

GE RANGE

Model JB645RKSS

Near Pueblo West, CO 81007

Domingo

Job Details: 01/31/2024

Customer says it was a bad breaker and it got fixed

We serviced a

SUBZERO REFRIGERATOR

Model 550

Near Colorado Springs, CO 80904

Ralph

Job Details: 01/31/2024

"unit has a locked compressor, will neede to be replaced, cust needs to talk with home warranty, and then will call...part and cost 7006959 $410.00, tx 33.62, mps (refrigerant) 255.00, labor 795.00, sc 149.95, total cost 1643.57, cust paying service fee today of 149.95, which leaves remaining balance of 1493.62.....autho no. 3RKRP9"

We serviced a

GE DRYER

Model GTD42EASJ2WW

Near Colorado Springs, CO 80911

David

Job Details: 01/31/2024

Checked dryer Dryer would only run with start button pushed. Idler arm not touching switch GE tech line suggested to bend the bottom some. That did work and the dryer is running good. GE case number 12154868

We serviced a

JENNAIR COOKTOP

Model JED8430ADB

Near Monument, CO 80132

Brandon

Job Details: 01/31/2024

"Glass top broke, needs new glass top. Svf paid $149.95 Auth# Y4MAC9, 74007072 $648.48, Labor $229.95, Svf $149.95, Mps $14.50, Tax $53.18"

We serviced a

SAMSUNG REFRIGERATOR

Model RSG307AARS/XAA

Near Colorado Springs, CO 80921

Brandon

Job Details: 01/31/2024

Cx cancelled

We serviced a

AMANA WASHER

Model NTW4519JW2

Near Albuquerque, NM 87121

Larry

Job Details: 01/31/2024

Installed parts and tested good - Unit is good to go

We serviced a

KITCHENAID WALL OVEN

Model KOSE500ESS05

Near Colorado Springs, CO 80908

Jerimiah

Job Details: 01/31/2024

Installed replacement components unit check ok.

We serviced a

SCOTSMAN ICE MACHINE

Model SCCP30MA-1SU

Near Colorado Springs, CO 80904

Ralph

Job Details: 01/31/2024

replaced part and unit checked okay

We serviced a

WHIRLPOOL REFRIGERATOR

Model ED2GVEXVD01

Near Colorado Springs, CO 80907

Carlos

Job Details: 01/31/2024

Installed control bracket. Ran test runs ok. Cx paid labor $179.95 CC Auth# 999ETF

We serviced a

KITCHENAID RANGE

Model KSGG700ESS6

Near Minturn, CO 81645

Antonio

Job Details: 01/31/2024

Found ignitor wire grounding out to frame fixed wire unit tested good

We serviced a

KITCHENAID REFRIGERATOR

Model KRSC503ESS00

Near Colorado Springs, CO 80903

David

Job Details: 01/31/2024

"Replaced door dispenser tube Tested and is operating good, no dripping"

We serviced a

SAMSUNG DRYER

Model DVE52M7750V/A3

Near Colorado Springs, CO 80925

Roman

Job Details: 01/31/2024

"Removed the old ui board and installed new one, reconnected the vent hose and tested the dryer. Dryer heating up and working great."

We serviced a

WHIRLPOOL RANGE

Model WFC150M0JB3

Near Colorado Springs, CO 80903

Carlos

Job Details: 01/31/2024

"Installed heater and sensor called tech line SR 7738373085. Power supply is only 215 volts amps are 9.4amps. Unit working as designed, it will take a little longer to heat up due to the power supply to the oven. This part of the city runs only between 215 to 220 volts not enough to draw 12 amps as recommended by whirlpool."

We serviced a

GENERAL ELECTRIC REFRIGERATOR/TOP

Model GNE27JYMWFFS

Near Colorado Springs, CO 80904

Roman

Job Details: 01/31/2024

"Replaced the inlet valve and ice maker, tested the dispenser and it started dispensing water. Ran the fridge and could hear the ice maker filling. Checked fans and made sure fridge is working properly, fridge working great."

We serviced a

SAMSUNG DISWASHER

Model DW80CG5450SRAA

Near Monument, CO 80132

Brandon

Job Details: 01/31/2024

Replaced kick plate and tested op all checks ok hass oqc passed

We serviced a

KENMORE DISHWASHER

Model 3631555993

Near Pueblo, CO 81005

James

Job Details: 01/31/2024

"went to install parts and found that in addition to ordered parts other failures have occurred. timer malfunctioning, chopper blade broke off and check valve failed. motor assem and check valve seem to be available but timer is nla unit is unrepairable. did not install new parts advised cust xcel will reach out if they have replacement option on plan."

We serviced a

BOSCH OTR MICROWAVE

Model HMB5051/01

Near Fountain, CO 80817

Ralph

Job Details: 01/31/2024

"total cost to repair would be 1335.12, cust is going to replace unit....autho no. 39CR3H"

We serviced a

WHIRLPOOL DRYER

Model WED5100HC2

Near Peyton, CO 80831

Aaron

Job Details: 01/31/2024

"Unit uninstalled in the garage upon arrival, Unit incorrectly wired at the terminal, heating element and thermostat are shorted out, removed and replaced components, corrected wires. Advised customer of 5 star survey."

We serviced a

SPEEDQUEEN WASHER

Model AWN63RSN115TW01

Near Pueblo, CO 81005

James

Job Details: 01/31/2024

installed ordered parts all ops test good

We serviced a

WHIRLPOOL DISHWASHER

Model WDT975SAHZ0

Near Colorado Springs, CO 80921

Glenn

Job Details: 01/31/2024

"Install New Adjuster Assys for upper rack. All OPS Test:OKSC $129.95 , Labor $179.95 , Adjuster $86.80 , Tax $7.12 , MPS $14.50 , Paid in Full $418.32 , Autho# Y9K4NL"

We serviced a

JENNAIR WALLOVEN

Model JMW3430IL03

Near Monument, CO 80132

Glenn

Job Details: 01/31/2024

"Received Broken Inverter W11325604 , Obtained new one from Marcone as per Sterling. Took an extra hour for drive time in picking up another part. Installed New Inverter & Magnetron. All OPS Test:OK"

We serviced a

SAMSUNG M/W OTR

Model ME21R7051SG/AA

Near Colorado Springs, CO 80921

Jerimiah

Job Details: 01/31/2024

"Installed replacement parts, unit check ok"

We serviced a

JENNAIR VENT HOODS

Model JXW8536HS1

Near Monument, CO 80132

Glenn

Job Details: 01/31/2024

Install New Control. All OPS Test:OK

We serviced a

SAMSUNG REFRIGERATOR

Model RF23J9011SG/AA

Near Monument, CO 80132

Brandon

Job Details: 01/31/2024

"Ice build up in ice room, cleared ice and replaced parts, tested op all checks ok"

We serviced a

SAMSUNG ELECTRIC OVEN

Model NE58F9500SS/AA

Near Monument, CO 80132

Brandon

Job Details: 01/31/2024

"Bearings in bottom fan wearing out, need new fan motor, Svf paid $129.95 Auth# X3T9VADG31-00007C $215.40, Labor $189.95, Svf $129.95, Mps $14.50, Tax $17.66"

We serviced a

SAMSUNG WASHER

Model WF45H6300AG/A2

Near Monument, CO 80132

Brandon

Job Details: 01/31/2024

"Front control panel not responding, power's on but that's it dial does not work buttons do not respond, need to replace sub PBA, Svf paid $129.95 Auth# MKPKHEDc92-01622a sub PBA $308.79, Labor $189.95, Svf $129.95, Mps $14.50, Tax $25.32"

We serviced a

DACOR DISHWASHER

Model DDW24M999US/DA

Near Monument, CO 80132

Brandon

Job Details: 01/31/2024

"Ran unit it did leak at front left corner of unit, called tech support, troubleshooted, cleared nozzles, readjusted and secured vane, ran smart install mode again and unit did not leak, all other checks ok, cx will monitor"

We serviced a

SAMSUNG DRYER

Model DV455EVGSGR/AA

Near Colorado Springs, CO 80922

Jessie

Job Details: 01/31/2024

Replaced belt and idler. All ok

We serviced a

SAMSUNG WASHER TOP LOAD

Model WA5OR5200AWI

Near Peyton, CO 80831

Kris

Job Details: 01/31/2024

ran test op diagnostic mode no issues found drain hose shoved down stand pipe. ran 5 large towels quick wash no issues. unit is working to spec at this time.

We serviced a

JENNAIR DOUBLE WALL OVEN

Model JMW2430LL02

Near Colorado Springs, CO 80908

Aaron

Job Details: 01/31/2024

"Customer states the microwave cavity light is not working, tightened door, door sitting well, door switches are properly engaging, tested microwave 5 heating cycles, popcorn setting is no cooking all popcorn kernels, discussed with techline situations, recommend customer allowing door to close harder for switches to engage, and state popcorn feature is working as designed, different brands and types will pop differently.SR7738372795. Advised customer of 5 star ."

We serviced a

MARVEL REFRIGERATOR

Model ML24BCG1RS

Near Colorado Springs, CO 80904

Roman

Job Details: 01/31/2024

"Noticed the condenser fan motor shaking a lot underneath the unit, frame the fan is sitting on is cheap sheet metal. Tightened screws and added some styrofoam type insulation. Collected labor of $99.95 check #"

We serviced a

MAYTAG WASHER

Model MHW6630HC3

Near Colorado Springs, CO 80908

Aaron

Job Details: 01/31/2024

"Unit is unable to complete cycle, debris lodged in pump assembly, cleared and tested unit, working and draining well now. Advised customer of 5 star survey."

We serviced a

WHIRPOOL WASHER

Model CAM2742TQ2

Near Rifle, CO 81650

James R

Job Details: 01/31/2024

Did drain but shakes badly believe issue with basket wobbles alot. Would need a basket motor coupling is broken. Agitator is loose as well. No woth it to repair. Paid service call $149.95 auth code. 9V49VK

We serviced a

ELECTROLUX COOKTOP

Model FFEF3016TWC

Near Rifle, CO 81650

James R

Job Details: 01/31/2024

signed disclaimer. Both burner switches are bad customer had parts replaced and test operation working as should. Customer paid $99.00 auth code A49R3Y Please fill out whirlpool tech satisfaction survey. Thank You.

We serviced a

GENERAL ELECTRIC REFRIGERATOR - S

Model GTS17GSNKRSS

Near Colorado Springs, CO 80910

Roman

Job Details: 01/31/2024

"Evap fan motor is vibrating and the rear cover, pushed the fan firmly on the motor and tightened screws, pushed the cover back to sit inside the drip catch."

We serviced a

DCS RANGE

Model RR-366

Near Elbert, CO 80106

Kris

Job Details: 01/31/2024

installed all parts sent ran test op all ok at this time.

We serviced a

MAYTAG DRYER

Model MED5430MW0

Near Colorado Springs, CO 80923

Aaron

Job Details: 01/31/2024

"Door gasket not fully connected, steam nozzle is not spraying properly, replaced and tested unit, working well now, discussed with techline, recommend using full load of clothes for spray to work without hitting door. SR7738369429. Advised customer of 5 star survey."

We serviced a

SAMSUNG MICROWAVE

Model ME16A4021AS/AA

Near Colorado Springs, CO 80908

Jerimiah

Job Details: 01/31/2024

Door handle completely broken off. Installed replacement door. Unit check ok

We serviced a

WHIRLPOOL RANGE

Model WFG550S0LZ4

Near Peyton, CO 80831

Jerimiah

Job Details: 01/31/2024

"Oven bake not heating, found igniter needed adjusting and repositioning and tightened back down. Unit check ok"

We serviced a

MIELE WALL OVEN

Model DGC6800-1

Near Colorado Springs, CO 80919

Jessie

Job Details: 01/31/2024

Replace bad drain pump. Found broken water line. Test op. All ok

We serviced a

BOSCH DISHWASHER

Model SHP65CM5N/01

Near Monument, CO 80132

Jessie

Job Details: 01/31/2024

Replaced facia. Test op. All ok

We serviced a

SAMSUNG WASHER

Model WF53BB8900ATUS

Near Colorado Springs, CO 80908

Jessie

Job Details: 01/31/2024

"Replaced dispenser, all ok"

We serviced a

FISHERPAYKEL DISHWASHER

Model DD24SAX9N

Near Elbert, CO 80106

Kris

Job Details: 01/31/2024

pulled door ran test op unit had hole in drain hose replaced hose cx had.

We serviced a

KITCHENAID MICROWAVE

Model KEMS308SSS00

Near Edgewood, NM 87015

Jason

Job Details: 01/31/2024

INSTALLED MAGNETRON AND INVERTER UNIT CHECKS OKAuth code:49KJL3$367.94

We serviced a

CAFE RANGE

Model CHS900P2M5S1

Near Edwards, CO 81632

Erik

Job Details: 01/31/2024

install gasket *see quick picsJOB COMPLETE

We serviced a

MAYTAG WASHER

Model MVW6230HW2

Near Albuquerque, NM 87111

Jason

Job Details: 01/31/2024

installed suspension unit checks ok

We serviced a

KITCHENAID WALLOVEN

Model KOCE500ESS22

Near Albuquerque, NM 87111

Jason

Job Details: 01/31/2024

installed support unit checks ok

We serviced a

KITCHENAID DISHWASHER

Model KDTE104KPS2

Near Albuquerque, NM 87112

Jason

Job Details: 01/31/2024

installed parts unit checks ok

We serviced a

WHIRLPOOL WASHER

Model WTW57ESVW1

Near Colorado Springs, CO 80925

Carlos

Job Details: 01/31/2024

"Installed drain pump ran test, runs ok. Cx had already paid in full"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT518SZFG02

Near Albuquerque, NM 87110

Jason

Job Details: 01/31/2024

checked unit found freezer door gasket had a gap reformed door gasket unit checks ok

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Colorado Springs, CO 80920

Glenn

Job Details: 01/31/2024

"Unit stopped working, not completing cycle, nor able to start new cycle. Water remaining in tub. Found broken harness wire at drain pump. Suggest replace lower wiring harness. W11643701 $105.82 , Tax $8.68 , MPS $14.50 , Labor $219.95, SC $149.95 , Customer Declined Estimate for now, as they want to contact Whirlpool, since unit should still be covered under warranty. Paid SC fee of $149.95 , Autho#JLPJ9L"

We serviced a

SAMSUNG REFRIGERATOR

Model RF28HFEDTSR/AA

Near Monument, CO 80132

Brandon

Job Details: 01/31/2024

"Error 33e, bottom ice pipe heater bad, top ice maker frozen up, replaced parts and tested op need ice pipe heater for bottom ice maker, all other checks ok"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT311FZDB02

Near Eagle, CO 81631

Antonio

Job Details: 01/31/2024

Found heater wire disconnected reconnected thawed unit out. unit tested good

We serviced a

KITCHENAID RANGE

Model KFGC500JSS05

Near Gypsum, CO 81637

Antonio

Job Details: 01/31/2024

Found ignitor not connected reconnected unit tested good

We serviced a

SAMSUNG DRYER

Model LJHKJH

Near Peyton, CO 80831

Kris

Job Details: 01/31/2024

installed element ran test op all ok at this time.

We serviced a

INSINKERATOR GARBAGE DISPOSAL

Model 79221K-ISE

Near Colorado Springs, CO 80920

David

Job Details: 01/31/2024

"Installed disposal Tested, running and no leaks"

We serviced a

SAMSUNG REFRIGERATOR

Model RF28HFEDBSG/AA

Near Colorado Springs, CO 80920

Mathew

Job Details: 01/31/2024

Reset fridge and turned off lock on control board. Defrosted icemaker and test op all okay. Paid svf 129.95 $129.95 CC Auth# 34AU94

We serviced a

SAMSUNG REFRIGERATOR

Model RF265BEAESR/AA

Near Colorado Springs, CO 80920

Mathew

Job Details: 01/31/2024

Found icemaker iced up. Defrosted and installed icemaker service kit. Test op all okay.

We serviced a

SAMSUNG REFRIGERATOR

Model RF23A9671SR/AA

Near Colorado Springs, CO 80921

Mathew

Job Details: 01/31/2024

Found shattered mini display. Replaced part and test op. All okay.

We serviced a

SAMSUNG REFRIGERATOR

Model RF23M8070SG/AA

Near Colorado Springs, CO 80907

Mathew

Job Details: 01/31/2024

"Replaced all icemaker parts, defrosted room and tested icemaker. All okay."

We serviced a

SAMSUNG WASHER

Model WF50R8500AV/US

Near Colorado Springs, CO 80918

Mathew

Job Details: 01/31/2024

"Found drain pump making grinding noise, not working effectively. Tried clearing drain pump issue persists. Unit will need drain pump. Unit not being repaired at the moment. Svf 129.95 $129.95 CC Auth# 9T44HAMPs 14.50Part 259.92 +21.31 tax Total parts and service $425.68Due on installLabor 179.95"

We serviced a

GE RANGE

Model CES750P4M3W2

Near Colorado Springs, CO 80927

Jessie

Job Details: 01/30/2024

Verified all unit functions. Customer said they were cooking when happened. Ran both ovens up to temp on bake. And than tried broil. Unit is safe to use.

We serviced a

SAMSUNG WASHER

Model WA40A3005AW/A4

Near Colorado Springs, CO 80916

Mathew

Job Details: 01/30/2024

Replaced control on unit due to 4c error code. Test op unit is working as expected. If issue persists unit will need lid lock.

We serviced a

SAMSUNG OTR MICROWAVE

Model ME17R7021ES/AA

Near Monument, CO 80132

Jerimiah

Job Details: 01/30/2024

"Called techline, dismounted unit, found numerous screws missing from unit including hv trans mounting screws. Techline documented everything, took pics, techline deemed unit as poor installation despite unit seeming to have been scavenged for screws. Unit never had prior work done on unit. Closing call."

We serviced a

MAYTAG WASHER

Model MVW5430MW1

Near Breckenridge, CO 80424

Antonio

Job Details: 01/30/2024

"Found loose nut at cam, so i thightened unit tested good"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ08

Near Colorado Springs, CO 80909

Ralph

Job Details: 01/30/2024

INSTALLED PARTS AND CHARTGED THE UNIT UNIT CHECKED OKAY

We serviced a

WHIRLPOOL RANGE

Model WEE745H0LZ3

Near Colorado Springs, CO 80925

Carlos

Job Details: 01/30/2024

"Installed control board, sensor and inserts. Ran test, oven cycles ok. Cx will observe"

We serviced a

BOSCH DISHWASHER

Model SHXM88Z75N/01

Near Colorado Springs, CO 80920

Jessie

Job Details: 01/30/2024

Replacent vent and fan. All ok

We serviced a

SAMSUNG REFRIGERATOR

Model RF28JBEDBSG/AA

Near Colorado Springs, CO 80923

Brandon

Job Details: 01/30/2024

"Error 40c, auger clip broke, replaced parts and tested op all checks ok"

We serviced a

BEKO DISHWASHER

Model DUT25401W

Near Colorado Springs, CO 80920

Roman

Job Details: 01/30/2024

"Removed the outer door panel and installed new one, ran the dishwasher and checked for leaks. Dw is working great."

We serviced a

ELECTROLUX DISHWASHER

Model EIDW6305GS1

Near Colorado Springs, CO 80904

Roman

Job Details: 01/30/2024

"Ran the dw and it did not come up with the error code, error code is indicating not enough water, issue did happen a couple weeks ago when we had cold weather and have a feeling that mightve caused some issues. Checked the valve and it was also not open all the way. Opened it up and let dw run, tightened the door screws and filled the rinse aide, also noticed the center spray arm is hitting the fill tube. Fill tube assy discontinued. Paid sc $129.95 CC Auth# 393K4E"

We serviced a

GE STACK UNIT

Model GUD27ESSM1WW

Near Colorado Springs, CO 80910

Roman

Job Details: 01/30/2024

"Installed new timer and new door, made sure washer and dryer both are working properly. Washer and dryer working great."

We serviced a

SAMSUNG DRYER

Model DVE55M9600V/A3

Near Colorado Springs, CO 80918

Brandon

Job Details: 01/30/2024

"Unit overheating issue, could not replicate, checked all sensors and heater tested op all to spec all checks ok, recommend cleaning dryer vent,Svf paid $129.95 Auth# 39C9F3"

We serviced a

SAMSUNG WASHER

Model WF45B6300AC/US

Near Colorado Springs, CO 80921

Brandon

Job Details: 01/30/2024

"Error 5c, Drain pump not working, replaced pump and tested op all checks ok hass oqc passed"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Colorado Springs, CO 80920

Glenn

Job Details: 01/30/2024

Install New Damper (2nd part in just over a month) All OPS Test:OK

We serviced a

KITCHENAID M/W OTR

Model KMHS120ESS09

Near Colorado Springs, CO 80921

Glenn

Job Details: 01/30/2024

"Bulb not working. Customer already attempted to replace bulb, but not working. Was getting power to bulb socket. They did have one other bulb, suggest customer trying other bulb. All OPS Now working. If problem returns, suggest replace control. Control - W11467687 $224.40, Tax $18.40 , MPS $14.50, Labor $189.95 , SC Fee $149.95 , Skip Signature, Autho#X34XP4"

We serviced a

WHIRLPOOL WASHER

Model WFW5620HW3

Near Divide, CO 80814

David

Job Details: 01/30/2024

Checked washer Found plug onto cold water valve no fully seated Reseated plug Tested and is working good

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ08

Near Falcon, CO 80831

Aaron

Job Details: 01/30/2024

"Water valve cracked, water off upon arrival, Needs inlet valve assembly Inlet valve assembly w11645245 $87.28Tax $7.16Supplies $14.50Hc $149.95Labor $219.95Total job $478.8430 day estimate No return on parts Auth 149.95 hc #4T9MLR"

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKB1

Near Peyton, CO 80831

Aaron

Job Details: 01/30/2024

"F1E1 acu error code upon arrival, removed and replaced control, tested unit, working well now. Installed litmus strip and advised customer of 5 star survey. *Note: power cord to dishwasher rubs against power cord for disposal, recommend different power cord so both cords are properly plugged in."

We serviced a

WHIRLPOOL WASHER

Model WFW75HEFW0

Near Colorado Springs, CO 80921

Glenn

Job Details: 01/30/2024

"Water leaking from rear vent at top, intermittently. (Especially Since guests have been visiting.) Possible soap overdose. Unable to duplicate reported problem. Suggest customer make sure that they are only using 2 tablesppons of soap per full load. Paid SC fee of $129.95 via check #6224 , Autho# MR49HF"

We serviced a

DACOR WALLOVEN

Model CPS130B

Near Pueblo, CO 81001

James

Job Details: 01/30/2024

found resettable tstat in cavity tripped causing g no heat. reset and tested ops ckok collected 224.95

We serviced a

MAYTAG WASHER

Model MAH4000AWW

Near Colorado Springs, CO 80909

Roman

Job Details: 01/30/2024

"Ran the washer and it will fill and agitate, ran it on a drain and spin and the washer will not go into a spin cycle, hit the switch manually that the wax motor is supposed to push and washer went into a spin cycle. Recommend replacing the wax motor and switchWax motor #WP22002119$61.80Switch #WP22002162 $82.92Tax $11.87Total part $156.59MPs $14.50 Labor $199.95Sc $129.95Total cost $500.99Paid sc $129.95 CC Auth# R3E9V3"

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Peyton, CO 80831

Aaron

Job Details: 01/30/2024

"Tested unit through agitate and spin cycles, unit is working well at time of inspection, all parts replaced are working as designed, lowered front legs and verified unit is level, adjusted drain hose to help prevent tapping against the wall, unable to replicate sound from customer's video, tested unit with four bath towels while customer was present. Advised customer of 5 star survey."

We serviced a

MAYTAG WASHER

Model MVW7230HW0

Near Peyton, CO 80831

Aaron

Job Details: 01/30/2024

"Unit pulled out upon arrival, F8E1 Long fillF0E5 off balance loadF8E3 overflowingF0E3 overload error codes, tested unit through diagnostics, cold water valve clogged with debris, unable to achieve enough water in rinse, cleared and working well now. House uses well for water. Auth 149.95 hc #UNJ399"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF330PAHS5

Near Colorado Springs, CO 80924

Aaron

Job Details: 01/30/2024

"Circulation motor is shorted out, unit only gills and drains. Removed and replaced motor sump assembly. Tested unit and working well now, no leaks. Installed litmus strip and advised customer of 5 star survey."

We serviced a

MAYTAG WASHER

Model MVW7232HW1

Near Fountain, CO 80817

Carlos

Job Details: 01/30/2024

"Installed rotor, slider and clutch, ran test runs ok"

We serviced a

MAYTAG WASHER

Model MHW5630HC3

Near Pueblo West, CO 81007

James

Job Details: 01/30/2024

found shock out of bracket causing oob condition. secured and tested all ops test good.

We serviced a

KITCHENAID WALLOVEN

Model KOCE500ESS20

Near Monument, CO 80132

Jerimiah

Job Details: 01/30/2024

Reseated trim into proper location. Unit check ok.

We serviced a

ASKO DISHWASHER

Model 1585

Near Colorado Springs, CO 80906

Ralph

Job Details: 01/30/2024

"unit is leaking somewhere, pulled the unitn and cleaned up the water under neath the unit then i ran the unit for over an hour for t least 3 fills and washes and drains and saw no signs of leaking, not sure where the water is coming from may be from the door but again no signs during this wash, cust to monitor and most likely will repalce unit that is over 25 yrs old"

We serviced a

JENNAIR RANGE

Model JGRP548WP02

Near Colorado Springs, CO 80906

Ralph

Job Details: 01/30/2024

"unitn will not reset, once poweris reapplied, the user interface screen will always go back to the Jennair symblo and thats is it,not able to manipulatenthe controlstoput into a test, also the lights inside both ovens will also not come on. part # and cost, WPW10464534 #1384.28, tax 113.51, mps 14.50, labor 189.95, sc 169.95, total 1872.19, cust paying sc today of 169.95, will leave total of 1682.24. ...cust paying SC today, autho no. 3HKWEX"

We serviced a

SAMSUNG WASHER

Model WA50R5400AV/US

Near Colorado Springs, CO 80925

Mathew

Job Details: 01/30/2024

Replaced lid switch. Test op all okay.

We serviced a

KITCHENAID REFRIGERATOR

Model KRSC700HPS06

Near Dillon, CO 80435

Antonio

Job Details: 01/30/2024

Found unit not leveled. So i level fridge and adjusted doors unit looks good

We serviced a

WHIRLPOOL WASHER

Model WTW6157PW0

Near Monument, CO 80132

Glenn

Job Details: 01/30/2024

"reports: clicking or clacking noise. Noticed water dripping from Hot water supply connection at wall. Shut hot water off, informed customer about findings, suggest have plumber correct leak issue. Tightened motor bolt under unit, also removed coin from washplate gap. All OPS Test:OK, No out of ordinary Noises. If problem returns, order new slider assy."

We serviced a

WHIRLPOOL WASHER

Model WTW5000DW1

Near Colorado Springs, CO 80923

Aaron

Job Details: 01/30/2024

"F5E3 lid lock error code upon arrival, control is intermittent, gearcase, pulley, and suspension have worn from use, unit is loud in spin, Needs, gearcase, pulley, washplate, and suspension. Control w11116590 $298.67Gearcase w11454734 $296.20Washplate w10752283 $145.92Pulley w10721967 $76.43Suspension w11130362 $141.34Total parts $958.56Tax $78.60Supplies $14.50Hc $129.95Labor $259.95Total job $1,441.5630 day estimate No return on parts Auth 129.95 hc #EYKK34"

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Pueblo, CO 81005

Domingo

Job Details: 01/30/2024

Replaced capacitor with splutch and the actuator test washer and is spinning is working okay

We serviced a

WHIRLPOOL DRYER

Model GEQ9800PW2

Near Pueblo, CO 81006

Domingo

Job Details: 01/30/2024

Test temperature with house on vent and it would shut off at 104 took the vent out and it will reach to 190 and then shut down and go to 130 and start back up I clean the dryer had a lot of lint customer clean the hose put everything back up dryer start heating up to 190 and shut up and then start back up at 130 degrees everything is working correctly recommended to customer to get a duct cleaning company to clean her vent. Also customer had dryer already out so I left it out

We serviced a

JENN-AIR DOWNDRAFT VENT

Model JVD0303GS00

Near Dillon, CO 80435

Antonio

Job Details: 01/30/2024

"Found various cracks, not foil taped. So i tape them all up call whlp to report findings sr#7738358343"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF757SDHZ02

Near Albuquerque, NM 87114

Joe

Job Details: 01/30/2024

"cx complaint - loud humming, not cooling properly - installed parts ordered last visit - tested unit - unit good to go"