We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF540CWHZ11
Near Santa Fe, NM 87508
Joe
Job Details:
12/19/2024
"Cx complaint, refrigerator not cooling correctly, noise. Replaced gaskets and air diffuser ordered last visit. Tested unit, no air leaking from ff compartment and no clicking noise. Unit good to goAdvised cx about survey"
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JZ5
Near Albuquerque, NM 87121
Larry
Job Details:
12/19/2024
Installed control and tested good - Unit is good to go - Survey mentioned
We serviced a
KITCHENAID RANGE
Model KFGC506JSS05
Near Albuquerque, NM 87123
Jason
Job Details:
12/19/2024
Checked unit found igniter had migrated downward. repositioned ignitor unit checks ok
We serviced a
MAYTAG WALL OVEN
Model MEW7630AS00
Near Colorado Springs, CO 80920
Jerimiah
Job Details:
12/19/2024
Installed replacement gasket and thermal fuse. Unit check ok.
We serviced a
KITCHENAID WALL OVEN
Model KOSE900HSS
Near Elbert, CO 80106
Aaron
Job Details:
12/19/2024
"Removed and replaced console and ACU, programmed and tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
AMANA RANGE
Model AGR6303MMS0
Near Winter Park, CO 80482
Antonio
Job Details:
12/19/2024
Installed new acu and tested oven to 350?unit tested good
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Carbondale, CO 81623
James R
Job Details:
12/19/2024
Signed disclaimer. Wire harness to drain pump is broken. Replaced harness and capacitor. Test run unit in service test operating as should. Put a leak board under unit took pic.Please fill out tech satisfaction survey. Thank You.
We serviced a
KITCHENAID RANGE
Model KSDG950ESS3
Near Fraser, CO 80442
Antonio
Job Details:
12/19/2024
Installed new acu and capacitor turn fan on low then high both worked fine unitvtested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ18
Near Pueblo, CO 81003
Brandon
Job Details:
12/19/2024
"Replaced Ice maker and control, all checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ05
Near Granby, CO 80446
Antonio
Job Details:
12/19/2024
Installed new acu and thermistor turned unit on fridge is at 35? and freezer at -10? unit tested good
We serviced a
WHIRLPOOL OTR MICROWAVE
Model WMH31017HS10
Near Monument, CO 80132
Jerimiah
Job Details:
12/19/2024
"Installed replacement harness and bulb, unit check ok."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM08
Near Colorado Springs, CO 80924
Aaron
Job Details:
12/19/2024
"Connector terminal is not fully engaging for power to compressor start component, corrected and compressor came on, needs time to cool, recommend refrigerator to have outside temperature between 50 and 90f for best cooling performance. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, CO 80904
Carlos
Job Details:
12/19/2024
Found broken wire repair wire drains ok.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Fountain, CO 80817
Carlos
Job Details:
12/19/2024
Insufficient voltage coming from outlet only 65 VAC needs 220~240VAC. Cx needs an electrician to repair.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Pueblo, CO 81001
James
Job Details:
12/19/2024
Found lid lock inop. Replaced with pre-ordered parts all ops test good
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Colorado Springs, CO 80924
Aaron
Job Details:
12/19/2024
"Circulation motor is shorted out, removed and replaced motor sump assembly, tested unit, working well now, no leaks, installed litmus strip and advised customer of 5 star survey."
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Peyton, CO 80831
Aaron
Job Details:
12/19/2024
"Bent blower blades, microwave turntable motor and shaft are also intermittently screeching during use, removed and replaced components, tested unit, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Monument, CO 80132
Dvante
Job Details:
12/19/2024
"Replaced lid, strike and both hinges. The door was able to lock on its own. Tested diagnostic mode, no leaks, no errors. Unit is working as designed"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMB4
Near Colorado Springs, CO 80916
Carlos
Job Details:
12/19/2024
"Ran test, found unit was unbalanced tilting forward, balanced leveling feet all ok"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Pueblo West, CO 81007
James
Job Details:
12/19/2024
Found unit with open heating element & tstat. Replaced with pre-ordered parts all ops test good
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Grants Pass, OR 97527
Jeff
Job Details:
12/19/2024
Installed parts tested machine working as should no leaks
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ18
Near Grants Pass, OR 97527
Jeff
Job Details:
12/19/2024
Found packing tape flapping next to condenser fan. Removed tested working as should
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM05
Near Medford, OR 97501
Jeff
Job Details:
12/19/2024
Installed cam tested door working as should.
We serviced a
KITCHENAID WALL OVEN
Model KOSE500ESS20
Near Bend, OR 97703
Austin
Job Details:
12/19/2024
Calibrated unit. Installed parts ordered. Tested unit all ops sat per factory spec. Units within 5 degrees of points.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Redmond, OR 97756
Austin
Job Details:
12/19/2024
Installed parts ordered. Tested unit. All ops sat per factory spec.
We serviced a
MAYTAG DRYER
Model MED6500MW0
Near Wolf Creek, OR 97497
Jeff
Job Details:
12/19/2024
Installed parts tested machine no more noise
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Los Lunas, NM 87031
Larry
Job Details:
12/18/2024
"Installed parts listed, ran test cycle and tested good - Unit is good to go"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM1
Near Rio Rancho, NM 87124
Joe
Job Details:
12/18/2024
"Cx complaint, Dishwasher doesn't wash dishes. Inspected unit, found wash motor bad. Replaced sump assembly and tested on quick wash. Unit washing fine nowAdvised cx about survey"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Socorro, NM 87801
Larry
Job Details:
12/18/2024
"Installed parts listed, calibrated and ran test cycle - Unit is operating as designed"
We serviced a
MAYTAG RANGE
Model MGR6600PZ1
Near Peralta, NM 87042
Larry
Job Details:
12/18/2024
Installed door glass - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ02
Near Albuquerque, NM 87123
Jason
Job Details:
12/18/2024
Installed compressor and evap. charged unit up pressures and frost pattern check good. unit opperation checks ok
We serviced a
MAYTAG WASHER
Model MVW5435PW0
Near Los Lunas, NM 87031
Larry
Job Details:
12/18/2024
CX complaint - Damaged colthes - Inspected unit and found the agitator came loose - Secured agitator with loc-tite - Ran test cycle and tested good - Unit id good to go
We serviced a
KITCHENAID DISHWASHER
Model KDTE404DSS0
Near Colorado Springs, CO 80906
Carlos
Job Details:
12/18/2024
Installed adjuster and spray arm all ok
We serviced a
MAYTAG DRYER
Model MED7230HW1
Near Colorado Springs, CO 80915
Carlos
Job Details:
12/18/2024
"SR- 7740558839 unit needed software update, completed cx will observe"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ03
Near El Jebel, CO 81623
James R
Job Details:
12/18/2024
Signed disclaimers.Unit was unplugged when I arrived. Put unit into service diagnostics. test 5 defrost 1.5 amps good. so defrost cycle is good. Checked frz compartment thermistor not reading. Removed control checked wire connections found the one for thermistors no snapped in place connected good then took a reading 3.93k ohms at 62.7 degrees. Frz thermistor 5.39k ohms at 53.6 degrees so both thermistor are working. Checked evap thermistor 4.53k ohms so is working. Checked compressor amps .79 good. Condenser fan is running. Evap fan and dampner are also working. Starting to cool down in Frz and F.F. areas. All light switches are working. Operating as should. for future reference leave unis running if possible.
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Edwards, CO 81632
Antonio
Job Details:
12/18/2024
Installed new acu and ran a cycle for proper operation unit tested good
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Colorado Springs, CO 80921
Dvante
Job Details:
12/18/2024
"Checked unit, customer explained the temperature drops when timer is on. Not baking properly. Tested the temperature and saw the temp staying steady. The main board is going to cycle both elements when losing temperature. Temp will rise and go down keeping the set temperature steady. No issues with unit"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT104TFDW03
Near La Junta, CO 81050
James
Job Details:
12/18/2024
Replaced preordered parts for temp concerns tested ops all ckok
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS2
Near Fountain, CO 80817
Carlos
Job Details:
12/18/2024
"Cx has water built up in tray, causing leak sensor to go off. Dishwasher was unleveled leaning forward, raised feet, cx will observe. Home floor is too high and counter is too low to remove unit to inspect other areas, making it inaccessible."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, CO 80918
Dvante
Job Details:
12/18/2024
"Replaced suspension rods, tested the diagnostic mode. No loud thumping and knocking noise. Unit is working as designed"
We serviced a
MAYTAG REFRIGERATOR
Model MSS25C4MGZ06
Near Colorado Springs, CO 80908
Aaron
Job Details:
12/18/2024
"Removed and replaced components, tested operation, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Bend, OR 97702
Levi
Job Details:
12/18/2024
"Replace dual water valve and bucket, cleaned up all the ice buildup then tested. I'll test check okay"
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Medford, OR 97501
Jeff
Job Details:
12/18/2024
Installed parts and Found hose connection to fill valve loose retightened tested and monitored no more leaks working as should
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Prineville, OR 97754
Austin
Job Details:
12/18/2024
Installed parts ordered. Tested unit all ops sat per factory spec.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS00
Near Prineville, OR 97754
Austin
Job Details:
12/18/2024
Installed new board to unit. Tested all ops sat per factory. Unit harvest and fills with water. No error codes for fridge or ice maker.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Eagle Point, OR 97524
Jeff
Job Details:
12/18/2024
Arrived no one home no answer Rick called and customer canceled
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ2
Near Bend, OR 97702
Levi
Job Details:
12/18/2024
Replace pump assembly and water inlet. Tested all checks okay
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS11
Near Bend, OR 97702
Levi
Job Details:
12/18/2024
"Replaced door seals, tested good"
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Rifle, CO 81650
James R
Job Details:
12/18/2024
Customer signed disclaimer. Removed outer panel and replaced ACU then tested in service diagnostics test. No error codes when done. Operating as should. Put a leak board under unit and took pic. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Redmond, OR 97756
Austin
Job Details:
12/18/2024
Installed parts tested unit all ops sat per factory spec.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KWH1
Near Carbondale, CO 81623
James R
Job Details:
12/18/2024
Signed disclaimer. Removed outer door panel and replaced ACU and outer door asy. Reassembled unit test run service diagnostics test no codes present let go thru cycle. Went thru fine no issues and no error codes when done. Operating as should. Please fill out tech satisfaction survey. Thank You. Put a leak board under unit and took pic.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ
Near Colorado Springs, CO 80907
Carlos
Job Details:
12/18/2024
"Installed Sump assembly and control board runs all ok. Called Techline 7740564095, cx states dishwasher does not dry properly. Looked at wax motor reservoir no rinse aid present, instructed cx to use rinse aid to dry dishes."
We serviced a
WHIRLPOOL DRYER
Model WED5050LW0
Near Colorado Springs, CO 80921
Charles
Job Details:
12/18/2024
"Open element, need part 279838, pick up part from shop and return, installed element and tested"
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Los Lunas, NM 87031
Larry
Job Details:
12/18/2024
When installing the latch I found the machine infested with mice - Called Assurant to document (24001040299DF) - Assurant said we will be paid for today but not in the future becaust they cancelled further warranty - Tech has part
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA
Near Peyton, CO 80831
Brandon
Job Details:
12/18/2024
Replaced ice maker and cycled all checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW1
Near La Pine, OR 97739
Levi
Job Details:
12/18/2024
Replaced control board tested good
We serviced a
MAYTAG RANGE
Model MER7700LZ2
Near Colorado Springs, CO 80925
Carlos
Job Details:
12/18/2024
"SR-7740560164 User wear and tear. Called Assurant techline glass top has flakes coming off. purely cosmetic. Handle on door was loose, tighten handle all ok."
We serviced a
GE WASHER
Model GFW550SSN5WW
Near Colorado Springs, CO 80918
David
Job Details:
12/18/2024
"Ran diagnostics, Diagnostics codes 38, 26, 92, 39, 8, 32. Ran through the diagnostics that they correspond to, all good, cleared codes. Ran a couple of cycles, then checked for error codes again, none at this time."
We serviced a
VIKING RANGE
Model VESO530SS
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
12/18/2024
Installed replacement parts and rework. Unit check ok charged labor as quoted chk#3392 $249.00 CK Auth# WHM99T
We serviced a
GE DISHWASHER
Model GDT695SSJ0SS
Near Vail, CO 81657
Erik
Job Details:
12/18/2024
disconnect comm cable to UI and plug back in - UI woke up and is functioningconnect to smartHQ service: apply software update multiple errors with MCB (parametric update should fix)* see quick picsCX to test - MCB WD21X24901(suspected corrosion)$199.95 PAID autho#FR3TN3JOB COMPLETE
We serviced a
BOSCH WALL OVEN
Model HMC80252UC/05
Near Colorado Springs, CO 80919
Ralph
Job Details:
12/18/2024
"after pricing the repair it would have been over 1000.00, so cust does not want to repair"
We serviced a
GE DRYER
Model GFD14ESSNWW
Near Aspen, CO 81611
Sean
Job Details:
12/18/2024
"checked unit MN/SN POPcustomer signed disclamer.opened unit checked basket good.closed and sarted. basket is rubbing the right hand side panel. unplugged unit and removedtop panel, controle panel, and front cover to gain acsess to the R side panel.found where side panel was pushed in at.pushed panel back into square.reassembled unit restored power and tested unit no longer rubbing .tested unit good.thank you and please go online to D-3 A/OK appliance and fill out a tech servey."
We serviced a
PROFILE WASHER
Model PTW605BSR1WS
Near Avon, CO 81620
Erik
Job Details:
12/18/2024
RENTAL PROP - ACCESS WITH DOOR CODEconnect to smartHQ service: F26 (inactive) out of balance final spin - TOO MUCH OR TOO LITTLE LOAD IN BASKETperform spin test: 800 rpm - OK* see quick picsuser error loading issue call GE customer relations for instruction on loading/ use and careCX not available for signature
We serviced a
PROFILE WASHER
Model PTW605BSR1WS
Near Avon, CO 81620
Erik
Job Details:
12/18/2024
RENTAL PROP - ACCESS WITH DOOR CODEconnect to smartHQ service: F26 (inactive) out of balance final spin - TOO MUCH OR TOO LITTLE LOAD IN BASKETperform spin test: 800 rpm - OK* see quick picsuser error loading issue call GE customer relations for instruction on loading/ use and careCX not available for signature
We serviced a
MONOGRAM MICROWAVE OVEN
Model ZSB9232N2SS
Near Snowmass, CO 81654
Sean
Job Details:
12/18/2024
checked un it MN/SN POPcustomer signed disclamer.tested unit cound not reproduce problem.reset unit disconnected power.opened unit and checked for loose wire.found the ribon wires where not seated fulley.checked all fuses and thermal switches. found all tested good. found no error codes on unit.reassembled unit and tested. unit started and ran without reproducing problem.dign = unit had unsecured ribbon wire.
We serviced a
JENNAIR REFRIGERATOR
Model JFX2897DRP02
Near Colorado Springs, CO 80920
David
Job Details:
12/18/2024
"Installed compressor and valve, evacuated, and charged system. It is cooling down. There is a noise in the freezer from the evap motor area. The tabs that hold things together are broken off. Cx may call again for this."
We serviced a
DCS RANGE
Model CS-364GLSS-L
Near Florissant, CO 80816
Ralph
Job Details:
12/18/2024
UNIT IS WORKING AS INTENDED.
We serviced a
ASKO DISHWASHER
Model DBI664
Near Woodland Park, CO 80863
Ralph
Job Details:
12/18/2024
"called tech support we did a reset and unit is now working, cust to monitor..autho no. 93R3X4"
We serviced a
JENN-AIR WALL OVEN
Model JMW2430LL03
Near Colorado Springs, CO 80904
Jerimiah
Job Details:
12/18/2024
"Installed replacement components. Unit check ok, if problem persists of console blinking out, needs smps board replaced. Cust will keep track of unit functionality."
We serviced a
JENNAIR WALL OVEN
Model JJW9430DDS
Near Colorado Springs, CO 80924
Charles
Job Details:
12/18/2024
"Door hinges failed, original JennAir, parts no longer available. Paid service fee $159.95 autho C4993H"
We serviced a
MIELE RANGE
Model KMR1136-1G
Near Eagle, CO 81631
Erik
Job Details:
12/18/2024
install spark node/ test: ignition and flame present/ shuts off immediately: FAILcall Miele TAG: flame monitor 10126991 ($698.11)CX will call Miele for consession requestopen unit and check continuity on spake harness - GOODJOB COMPLETE
We serviced a
JENN-AIR DISHWASHER
Model JDB9000CWP2
Near Albuquerque, NM 87111
Jason
Job Details:
12/18/2024
un-plugged unit and plugged it back in unit opperation checks okAuth code: C44C3U$151.85
We serviced a
SHARP MICRO DRAWER
Model KB6524PSYD
Near Monument, CO 80132
Jerimiah
Job Details:
12/18/2024
Installed replacement magnetron. Unit unit check OK $252.94 CC Auth# CFRHXW
We serviced a
FIVESTAR RANGE - GAS
Model n/a
Near Florissant, CO 80816
Ralph
Job Details:
12/18/2024
INSTALLED PART AND UNITY CHEC KED OKAY
We serviced a
ELECTROLUX REFRIGERATOR
Model EW23BC85KSSW
Near Colorado Springs, CO 80919
Ralph
Job Details:
12/18/2024
"unit had a frozen water line, called tech support unit is building up ice on the back wall of the unit , tech said there is no fix for that, thawed the line and put stuff to keep away form the wall cust has been advised"
We serviced a
WOLF RANGE
Model n/a
Near Colorado Springs, CO 80908
Charles
Job Details:
12/18/2024
Going into diagnostics when not in use. Touchscreen part number 806828Service fee $159.95Labor $269.95MPS $14.50Part $597.50Tax $49.00Total $1090.90Declined estimate at this time. 30 day estimate. Paid service fee $159.95 autho 994MVM
We serviced a
MAYTAG WASHER
Model MVWB835DW3
Near Colorado Springs, CO 80917
Aaron
Job Details:
12/18/2024
"Removed and replaced UI console, programmed and tested unit through diagnostics, working well now, no leaks, installed litmus strip. Total due was previously paid."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS03
Near Central Point, OR 97502
Jeff
Job Details:
12/18/2024
Customer meet me at door and said she canceled service days ago. Doesn't want repaired. Do to out of warranty
We serviced a
JENN-AIR RANGE
Model JGRP436WP02
Near Albuquerque, NM 87122
Jason
Job Details:
12/18/2024
Installed control checked heat cycling and temps unit opperation checks ok at this timeAuth code: 9UF4XW$227.80
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHV00
Near Colorado Springs, CO 80923
Charles
Job Details:
12/18/2024
"Installed control board.Service fee $139.95Labor $229.95MPS $14.50Part $312.89Tax $25.66Total $722.95Paid in full auth 3X3WL9, EF4H4P, L93RMJ"
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Rifle, CO 81650
James R
Job Details:
12/18/2024
Printed labels took pics ready to send.
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB86004MAA
Near Colorado Springs, CO 80909
Mathew
Job Details:
12/18/2024
Replace leaking filter case and dispenser. Test op all okay.
We serviced a
SAMSUNG RANGE
Model NX60A6511SG/AA
Near Peyton, CO 80831
Brandon
Job Details:
12/18/2024
Replaced board all checks ok
We serviced a
SAMSUNG COOKTOP
Model NA30N6555TS/AA
Near Monument, CO 80132
Dvante
Job Details:
12/18/2024
"Checked unit, saw the middle burner turning on improperly. Replaced the burner, igniter and cap. Burner is turning on properly. Unit is working as designed."
We serviced a
SAMSUNG MICROWAVE
Model MS19M8000AS/AA
Near Monument, CO 80132
Dvante
Job Details:
12/18/2024
"Checked unit, saw the door not opening properly. Replaced the body latch. Door is opening properly. Unit is working as designed"
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Colorado Springs, CO 80925
Mathew
Job Details:
12/18/2024
Found faulty control board. Replace control board. Test op on OQC. lol okay.
We serviced a
SAMSUNG RANGE
Model NX60A6511SS/AA
Near Colorado Springs, CO 80907
Mathew
Job Details:
12/18/2024
"Found broken bake igniter. Replace broken bake igniter. Test op in bake, all okay."
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Colorado Springs, CO 80922
Aaron
Job Details:
12/18/2024
"F7E4, F5E4 error codes upon arrival, slider tabs have worn, tub is unable to engage, removed and replaced slider and clutch, ran unit through DLMS and diagnostic cycles, working well now. Advised customer of 5 star survey."
We serviced a
JENNAIR WALL OVEN
Model JJW2430DS02
Near Rio Rancho, NM 87144
Joe
Job Details:
12/18/2024
"Cx complaint, getting key stuck error. Inspected unit, unable to clear error. Advised cx they need new console. Cx declined estimateAdvised cx about survey. Cx paid diagnostic fee by credit card Authorization number CNCX43"
We serviced a
WOLF RANGE
Model DF60650CG/S/P
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
12/18/2024
Installed rework kit. Unit check ok.
We serviced a
GE DISHWASHER
Model GDF610PSJ2SS
Near Edwards, CO 81632
Erik
Job Details:
12/18/2024
DOA -unit MC board failure - cnnect to smartHQ service: MC/UI replacement requiredCX will replace the unitJOB COMPLETEsterling approve $179.95 SC PAID autho#LMYT33
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHZ0
Near Albuquerque, NM 87114
Joe
Job Details:
12/18/2024
"Cx complaint, not draining. Replaced filter and cup ordered last visit. Made sure filters fitting correctly and unit is draining fine. Filled 2 times and drained good. Unit good to goAdvised cx about survey"
We serviced a
WHIRLPOOL DRYER
Model WED8127LW1
Near Rio Rancho, NM 87144
Joe
Job Details:
12/18/2024
"Cx complaint, light works intermittently. Replaced door switch ordered last visit. Tested light multiple times. Light working as designedAdvised cx about survey"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB08
Near Los Lunas, NM 87031
Larry
Job Details:
12/18/2024
Installed ice maker and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT148FZDB
Near Colorado Springs, CO 80910
Scott
Job Details:
12/18/2024
installed listed parts recharged checked op ok
We serviced a
KITCHENAID DISHWASHER
Model KUDI01TJBL1
Near Redmond, OR 97756
Austin
Job Details:
12/18/2024
Unit has a cracked tub in the bottom front corner. Unit is unrepairable.
We serviced a
CAFE RANGE
Model CES750P2MS
Near Aspen, CO 81611
Sean
Job Details:
12/17/2024
checke unit MN/SN customer signed disclamer.opened unit bottom convection oven.started unit fan as rubbing aganst back panel.powered off the unit and removed inside back panel.checked fan = found that the fan blade was off ballance.I adjusted the fan balde.reassembled the unit and tested. fan came on and was almost silent. tested the unit good.showed customer how to use diferant fetures.
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SR/AA
Near Pueblo West, CO 81007
James
Job Details:
12/17/2024
Installed ordered parts tested ops all ckok
We serviced a
MAYTAG WASHER
Model MVW6230HW
Near Colorado Springs, CO 80904
Carlos
Job Details:
12/17/2024
"Installed gearcase, actuator, cam & shield ran test all ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT541SZDW
Near Albuquerque, NM 87120
Larry
Job Details:
12/17/2024
Cx complaint - Water leaking into fridge - Inspected unit and found the evap drain frozen over - Cleared drain and i draining good - Unit is good to go