We serviced a
BOSCH DISHWASHER
Model SHP65CM5N/25
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
03/24/2025
Door was popping open but not falling the rest of the way open for auto dry.Leveled unit so that its not rubbing anywhere and pitched unit slightly forward. Door is now free of any obstruction and opening and closing properly. RK
We serviced a
THERMADOR DISHWASHER
Model DWHD660EFP/01
Near Colorado Springs, Colorado 80919
Charles
Job Details:
03/24/2025
"Installed mounting brackets and secured to cabinets. Service fee $159.95, Part $6.50, Tax $.53, Total $166.98, paid autho 3JAV4N"
We serviced a
BOSCH DISHWASHER
Model SHP65CM5N/25
Near Avon, Colorado 81620
Erik
Job Details:
03/24/2025
RIGHT SIDE DOOR SPRING CAME OUT OF TRACK* see quick picsreplace and test: PASSJOB COMPLETE
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC700HBS00
Near Roseburg, Oregon 97471
Jeff
Job Details:
03/24/2025
Installed compressor put 5.75oz 134. Gauges holding. Customer to monitor
We serviced a
GE MICROWAVE
Model JVM6175SK2SS
Near Monument, Colorado 80132
Charles
Job Details:
03/24/2025
"Not heating, fan runs when door opened, replaced door secondary interlock switch and tested.; used 1 WB24X829 (Secondary switch) from stock"
We serviced a
MAYTAG WASHER
Model MVW6200KW0
Near Pueblo, Colorado 81005
James
Job Details:
03/24/2025
Found previous tech that replaced actuator did not fully seat power to actuator. Secured wire and actuator and tested. All ops test good.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
03/24/2025
"Found obstruction in felt on machine. Remove obstructions. Install dryer repair kit. Test op, all okay."
We serviced a
SAMSUNG DRYER
Model DV45H6300EW/A3
Near Colorado Springs, Colorado 80921
Ryan
Job Details:
03/24/2025
"Dryer vent restricted behind unit.Advised customer to clean vent and not push unit all the way back to wall. Also advised customer to upgrade vent on exterior of home to a higher flow unit,No error codes and unit now testing ok.RK"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS26L3AF5
Near Pueblo West, Colorado 81007
Domingo
Job Details:
03/24/2025
Check wires from board to thermistor not ohm call tech line they told me mostly broken wires inside cabin so I Call assurance solutions they told me to close the ticket and tell customer they will contact them in 2 business day
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Albuquerque, New Mexico 87104
Larry
Job Details:
03/24/2025
CX complaint - Not spining - Inspected unit and found the slider failed - Replaced with TS and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Central Point, Oregon 97502
Jeff
Job Details:
03/21/2025
Installed parts tested machine no errors pump working
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Redmond, Oregon 97756
Levi
Job Details:
03/21/2025
"Replace timer, tested all checks okay"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Redmond, Oregon 97756
Levi
Job Details:
03/21/2025
"Installed all listed parts, tested, recalibrated control board. All tests okay no leaks at time of service. Did not complete install because I'm not sure if the machine is going to stay in this unit or not. Job complete"
We serviced a
KITCHENAID DISHWASHER
Model KDTM405PPS1
Near Grants Pass, Oregon 97527
Thomas
Job Details:
03/21/2025
Replaced dispenser. Ran tested okay with customer present. No leaks. Advised customer of survey
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Medford, Oregon 97504
Jeff
Job Details:
03/21/2025
Installed parts tested machine no leaks
We serviced a
WHIRLPOOL DRYER
Model WET4024HW0
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
03/21/2025
Installed repair kit runs ok
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS3
Near Peyton, Colorado 80831
Aaron
Job Details:
03/21/2025
"Normal cycle button is not working on UI console, removed and replaced console, ran unit through diagnostics, working well now, verified by customer, installed litmus strip and advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RZ00
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
03/21/2025
"Removed and replaced Main control and display.Tested operation and all now checks ok , unit is cooling. RK"
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS05
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
03/21/2025
"Water filter housing clip is not engaging, removed and replaced housing, purged water line, working well now, verified by customer, installed litmus strip and advised customer of survey."
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Pueblo West, Colorado 81007
James
Job Details:
03/21/2025
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/21/2025
"Damper control is chirping during operation, removed and replaced control assembly, tested unit through diagnostics, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Pueblo, Colorado 81006
James
Job Details:
03/21/2025
"Installed ordered parts, tested ops all ckok"
We serviced a
WHIRLPOOL WASHER
Model WET4124HW0
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
03/21/2025
"SR-7741194945, smell is due to overloading machine, unit works ok. Safety team SR-7741144472"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Colorado Springs, Colorado 80917
David
Job Details:
03/21/2025
"Installed damper, it is quieter."
We serviced a
MAYTAG REFRIGERATOR
Model MFI2570FEZ15
Near Fountain, Colorado 80817
Carlos
Job Details:
03/21/2025
"UI had lock engaged, unlocked runs all ok"
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
03/21/2025
"Installed bake, broil elements and control board ran oven for 20 mins at 500 degrees runs ok"
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
03/21/2025
Installed handle all ok
We serviced a
WHIRLPOOL DRYER
Model WED560lHW2
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
03/21/2025
Installed tub ran tests all ok
We serviced a
WHIRLPOOL DRYER
Model WED6150PB0
Near Rifle, Colorado 81650
Sean
Job Details:
03/21/2025
"Customer signed disclaimer Verified MN SN POPTechnician found wires at terminal block to be loose, properly installed wires and power cord to enable testing and performed diag on unit. No error codes are present and unit passed all component tests and is now functioning properly according to manufacturer specifications, noting only that the water valve can be heard when tested without water supplied, but is operating properly.Only time unit beeped was in the test mode to test the moisture sensor or end of cycle. Thank you and please fill out a technician survey"
We serviced a
WHIRLPOOL FREEZER
Model WZF34X16DW10
Near Grand Junction, Colorado 81504
Sean
Job Details:
03/21/2025
"Customer signed disclaimerVerified unit MN SN POPInspected received parts, verified correct parts in good condtition.Tech verified non-functionl compressor on unit. Tech discharged refrigerant, removed failed compressor and components and installed new replacement compressor, filter drier, and start components. System put charged with nitrogen and maintained pressure properly throuought the 30 minute test period. System was placed under vacuum and properly maintained as well. System was charged with 1.45oz R-600 refrigerant. Tech confirmed unit is cooling properly and operating within manufacturer specifications.Thank you for allowing us to service your freezer today! please take a moment and let us know how we did by completing our technician survey. Have a wonderful day!"
We serviced a
WHIRLPOOL RANGE
Model WEG745H0FS0
Near Peyton, Colorado 80831
Aaron
Job Details:
03/21/2025
"Arrived onsite and tested unit, bake cycle began, broil would not start, removed and replaced module control, tested unit and both bake and broil will not light, inspected unit and found mouse droppings in unit behind control, intermittently receiving power at the module. Advised customer of situation and survey. Techline closed at time of inspection."
We serviced a
WHIRLPOOL RANGE
Model WEG745H0FS1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/21/2025
"Removed and replaced switch assembly, tested all burners, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/21/2025
"Belt slipping on drive pulley, removed and replaced components, tested unit through diagnostics, working well now. Advised customer of settings to get most water flow to help dissolve soap. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Monument, Colorado 80132
Dvante
Job Details:
03/21/2025
"Checked unit, found the water is not spraying inside again. Checked the voltage from the control board. It wasnt getting around getting 125 v. Checked the motor connection and each each wire to the ground. Also checked the motor to see if it was connected properly and it was. Tech support has decided to deemed unit as non repairable. Did give the customer the SR number to call customer service.SR7741159864"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Rio Rancho, New Mexico 87124
Larry
Job Details:
03/21/2025
CX complaint - Not draining or starting - Inspected unit and found the capacitor leaked and the drain pump harness failed - Replaced with pre-id parts and tested good - unit is good to go
We serviced a
MAYTAG WASHER
Model MVW7230HC1
Near Rio Rancho, New Mexico 87124
Larry
Job Details:
03/21/2025
Installd gearcase and tested good - unir is good to go - Surney mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
03/21/2025
"cx complanit - loud noise - replaced clutch and slider,ran diagnostic passed, unit is working properly - survey mentinoed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28N9780SG/AA
Near Pueblo, Colorado 81005
Domingo
Job Details:
03/21/2025
Replaced compressor and filter drier test it everything came on
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Grand Junction, Colorado 81501
Sean
Job Details:
03/21/2025
Customer signed disclaimer Verified MN SN POP Verified replacement part is correct and intact. Tech removed failed fill valve assembly and installed replacement assembly. Tech performed test cycle and confirmed that unit is now operating properly within manufacturer specifications.Thank you for allowing us to service your Washer today! Don't hesitate to call us with any questions or all of your appliance needs Please take a moment to let us know how we've done by completing our technician survey and have a wonderful day.
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Bend, Oregon 97701
Levi
Job Details:
03/21/2025
Replace listed parts and cleaned drain pump. Tested I'll check is okay and cleared error codes
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW0
Near Albuquerque, New Mexico 87109
Jason
Job Details:
03/21/2025
Installed control and valve ran calibration cycle and quick wash unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL FREEZER
Model WZF34X20DW05
Near Rio Rancho, New Mexico 87144
Larry
Job Details:
03/21/2025
Installed parts listed and getting good heat transfer - Unit is operating as designed - Survey mentioned
We serviced a
KITCHENAID DISHWASHER
Model KUDR01TJBL0
Near Albuquerque, New Mexico 87111
Jason
Job Details:
03/21/2025
"Cx stated unit is not coming on again found thermal fuse open and control looks to have been getting hot. control, fuse and door switch recomended. found control #8528172 is NLA Called 3rd party team to update them of current findings. SR7741096352warranty company to contact cx in next 2-3 buisness days with options. spoke to cx about review"
We serviced a
KITCHENAID DISHWASHER
Model KDTE104KPS0
Near Albuquerque, New Mexico 87110
Jason
Job Details:
03/21/2025
Checked unit found wash motor weak. installed pump motor assy ran normal cycle unit opperation checks okspoke to cx about review
We serviced a
KITCHENAID ICE MACHINE
Model KUIX335HPS01
Near Colorado Springs, Colorado 80907
Charles
Job Details:
03/21/2025
"Power light flashing, bin sensor error per tech line. Need part WPW10511923. Picked up from Marcone and returned. Service fee $139.95, Labor $229.95, MPS $14.50, Part $102.26, Tax $9.39, Total $495.05, paid in full autho AWA34E"
We serviced a
SAMSUNG WASHER
Model WD53DBA900HZA1
Near Colorado Springs, Colorado 80924
Brandon
Job Details:
03/21/2025
"Called tech support, found drain pump clogged with Lint and plastic from customer, tested operation hass oqc passed please add photos to GSPN ticket"
We serviced a
SAMSUNG DRYER
Model DVE50R5200W/A3
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
03/21/2025
"Bad TCO, replaced heater assy hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RS22T5201SR/AA
Near Colorado Springs, Colorado 80908
Dvante
Job Details:
03/21/2025
Replaced the ice maker and main pcb. Tested unit and passed HASS. Tested the ice maker and motor is functioning properly. Unit is operating as designed.
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Green Mountain Falls, Colorado 80819
Mathew
Job Details:
03/21/2025
Found inlet valve stuck open. Replace valve and inlet hose assy. Install service kit. Test op. Unit working as expected.
We serviced a
SAMSUNG RANGE
Model NE63A6511SS/AA
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
03/21/2025
Replace assy touch pad. Test op all okay.
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Colorado Springs, Colorado 80925
Mathew
Job Details:
03/21/2025
Replace faulty pump and replace wire harness as multiple wires were severed by corrosion. Test op all okay. Left leak strip.
We serviced a
SAMSUNG REFRIGERATOR
Model RF23A9671SR/AA
Near Colorado Springs, Colorado 80920
Brandon
Job Details:
03/21/2025
"Leaking on fridge room floor, called tech support did visual inspection, Samsung recommends original Samsung filter and they will contact customer with the next steps this ticket can be closed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF22A4121SR/AA
Near Colorado Springs, Colorado 80926
Mathew
Job Details:
03/21/2025
Found fridge set to 34 degrees. Temp checked at 34 degrees on bottom. 41 degrees on top. Freezer set to 3. Temp checked to 2. All fans working. No sealed systems issue. Cx was under impression parts and labor were covered by extended warranty. Recommend freezer evap assembly and temp sensor for fridge. Collect svf. $139.95 CC Auth# CUV4YLAuth# CUV4YL
We serviced a
GE REFRIGERATOR
Model ZISB420DRF
Near Colorado Springs, Colorado 80904
Charles
Job Details:
03/21/2025
Installed compressor kit
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS00
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
03/21/2025
"Unit is not cooling, water dispenser and auger motor not operating, compressor is on, both cavities fans are not working, discussed situation with techline, ACU recommended, was able to reset unit and test components and fans. Approved onsite, picked up and replaced control, unit needs time to cool. ACU $274.22Tax $22.59Supplies $14.50Hc $139.95Labor $229.95Total job $681.11No return on parts Auth total job $681.11 #WLWH4USR7741193529"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Los Lunas, New Mexico 87031
Larry
Job Details:
03/21/2025
CX complaint - No power in the fridge and not cooling - Inspected unit and found the RC has no power but the FC has lights - Power on the UI but good power to it - No power to the compressor - Unit needs control - CX wants to talk thing over with her father - Collected SC-auth-WP3JE9
We serviced a
ASKO DISHWASHER
Model D5554
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
03/21/2025
"Control board not responding to commands.Parts not available , RKS/C $159.95Auth 49JK4P"
We serviced a
LG DISHWASHER
Model LDF5545SS
Near Florence, Colorado 81226
Domingo
Job Details:
03/21/2025
Ran a cycle to see where it was leaking from the outer tub customer says he will replace it
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Rio Rancho, New Mexico 87124
Larry
Job Details:
03/21/2025
CX complaint - Fridge making grinding noise - Inspected unit and found a piece of mastic rubbing against the condenser fan - Removed mastic and tested good - Unit is operating as designed - Survey mentioned
We serviced a
JENNAIR REFRIGERATOR
Model JS48PPDUDE00
Near Medford, Oregon 97504
Jeff
Job Details:
03/21/2025
Found machine has a slight gargle but machine is running good has good ice production good frost pattern. Customer is going to monitor.
We serviced a
JENN-AIR RANGE
Model JER8750BAB
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
03/21/2025
"the switch the cust needs is the dual element switch, that part is no longer available, autho no. 9fa4uv"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS2
Near Peyton, Colorado 80831
Ryan
Job Details:
03/21/2025
Unit working properly and current operating noise is normal. Inst customer to run a couple cleaning cycles RKS/C $139.95Auth 3E99LF
We serviced a
CAFE DISHWASHER
Model CDT858P2V1S1
Near Grand Junction, Colorado 81507
Erik
Job Details:
03/21/2025
need RA for additional doorJOB COMPLETE
We serviced a
GE RANGE
Model JEP5030DT1BB
Near Leadville, Colorado 80461
Erik
Job Details:
03/21/2025
install switches and test: PASS* see quick picsJOB COMPLETE
We serviced a
GE DISHWASHER
Model GDT670SYV0FS
Near Pueblo, Colorado 81001
James
Job Details:
03/21/2025
Installed ordered parts tested ops all ckok
We serviced a
GE RANGE
Model GRF500PV1WW
Near Colorado Springs, Colorado 80916
David
Job Details:
03/21/2025
Replaced glass top.
We serviced a
GE REFRIGERATOR
Model GFE26JYMXFFS
Near Colorado Springs, Colorado 80925
David
Job Details:
03/21/2025
"Replaced ice box fan, it is moving good air. Cx keeping an eye on it."
We serviced a
ELECTROLUX DRYER
Model ELFE7437AG
Near Cañon City, Colorado 81212
Domingo
Job Details:
03/21/2025
Customer complaining that machine wouldnt heat up like her old one I test it and it will go to 190? back to 131? working normal operation
We serviced a
DACOR RANGE
Model HGPR36SNGH
Near Monument, Colorado 80132
Jerimiah
Job Details:
03/21/2025
Call for heat light not working. Also heating 50? hotter then required. Main wire harness with light would need replacing. Holding off on harness. Calibrated cw to cool off. After several attempts got unit calibrated charged service call $169.95 CC Auth# T3UYT3Harness DE81-07592ALight DE81-08557ACcw to decrease temp
We serviced a
SCOTSMAN ICE MACHINE
Model SCN60PA1SS
Near Colorado Springs, Colorado 80926
Ralph
Job Details:
03/21/2025
"found not fully plugged in, once i move d the cord the unit cme on cust to monitor..autho no. EKTLN9"
We serviced a
WHIRLPOOL WASHER
Model MVW5430MW1
Near Albuquerque, New Mexico 87122
Jason
Job Details:
03/21/2025
Checked unit found actuator has failed also belt is slipping SC$139.95MPS$17.50LABOR$179.95ACTUATOR#W11481722$125.74BELT#W11239857$83.38TX$46.45TOTAL$592.97Auth code: EK99ER$151.85CX TO THINK OVER REPAIR
We serviced a
BOSCH WALL OVEN
Model HBL8743UC/05
Near Palmer Lake, Colorado 80133
Jerimiah
Job Details:
03/21/2025
Installed replacement blower with baffling. Unit check ok Cust will keep track of unit functionality.
We serviced a
GE RANGE
Model PGS960YP2FS
Near Silverthorne, Colorado 80498
Erik
Job Details:
03/21/2025
display in vacation/ sabbath mode
We serviced a
WHIRLPOOL DRYER
Model WED5100HW1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/21/2025
"Heating element is shorted out, took out thermal fuse, removed and replaced components, cleared unit of lint,tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Monument, Colorado 80132
Dvante
Job Details:
03/21/2025
Checked unit and found the unit drain pump stuck. Called tech support and was checking for voltage and ohms on the wires from the control board. All tested ok. Calibrated the unit to make sure it was operating properly. Could have been a loose connection. Otherwise the unit is operating as designed.SR7741195613
We serviced a
MAYTAG WASHER
Model MVWC465HW4
Near Colorado Springs, Colorado 80923
David
Job Details:
03/21/2025
"Hub and suspension rods loose. Replaced rods and basket hub, seems smoother running."
We serviced a
MIDEA WASHER
Model MLV45N1BWW
Near Pueblo West, Colorado 81007
James
Job Details:
03/21/2025
No m/s on unit per asu unit will be bought out. Advised cust asu will contact within 24-48 hrs
We serviced a
ASKO DRYER
Model T208H.W.U
Near Florissant, Colorado 80816
Charles
Job Details:
03/21/2025
"Not drying, inside of drum full of condensation. Perth filter plugged. Advised on cleaning of filters."
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Medford, Oregon 97504
Jeff
Job Details:
03/20/2025
"Installed springs, wiring, and pump tested machine working as should"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Grants Pass, Oregon 97526
Thomas
Job Details:
03/20/2025
Replaced parts listed. Ran tested okay with customer present. Advised customer of survey
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ2
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
03/20/2025
"Installed board, actuator and capacitor. Ran calibration and tests cycle runs ok."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RZ00
Near Peyton, Colorado 80831
Aaron
Job Details:
03/20/2025
"Ice maker tines bound, motor unable to proceed, corrected and tested unit through harvest cycle, working well now, needs time to cool. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW10
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
03/20/2025
Installed door runs all ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW10
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
03/20/2025
Installed glass all ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
03/20/2025
Installed listed parts all ok
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Rifle, Colorado 81650
Sean
Job Details:
03/20/2025
Checked unit MN SN POPCustomer signed disclaimer Removed and installed new control.Tested unit good.
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Albuquerque, New Mexico 87120
Larry
Job Details:
03/20/2025
Installed control and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Albuquerque, New Mexico 87121
Larry
Job Details:
03/20/2025
Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Albuquerque, New Mexico 87121
Larry
Job Details:
03/20/2025
CX complaint - Not draining - Inspected unit and - found the harness broken - Repaired harness and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Albuquerque, New Mexico 87121
Larry
Job Details:
03/20/2025
CX complaint - Not heating - Inspected unit and found the element and tco open - Replaced with pre-id parts and tested good - Survey mentioned
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Cedar Crest, New Mexico 87008
Jason
Job Details:
03/20/2025
Installed evap cover and control. unit opperationn checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ
Near Albuquerque, New Mexico 87104
Larry
Job Details:
03/20/2025
Installed ice bin and tested good - nit is good to go - Survey mentioned
We serviced a
SAMSUNG DRYER
Model dv42h5200ef/a3
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
03/20/2025
"Checked unit, did find the dryer heating. Checked inside and saw a lot of lint inside. Cleaned the lint out. Tested unit to see if heater was cycling properly and it was. Did advised customer to clean lint filter after every cycle.Service Fee-$139.95$139.95 CC Auth# J9JUYR"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Rifle, Colorado 81650
Sean
Job Details:
03/20/2025
Customer signed disclaimer Verified MN SN. Verified proper part was received and in good condition. Tech installed replacement control board Assembly and verified unit is functioning properly within manufacturer specifications. Thank you for allowing us to service your Washer today. Please take a moment and let us know how we've done by completing our tech survey. Have a wonderful day!Control was supplied.; used 1 W11578571 (Controller) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Rifle, Colorado 81650
Sean
Job Details:
03/20/2025
Customer signed disclaimer Verified MN SN. Verified proper part was received and in good condition. Tech installed replacement control board Assembly and verified unit is functioning properly within manufacturer specifications. Thank you for allowing us to service your Washer today. Please take a moment and let us know how we've done by completing our tech survey. Have a wonderful day!Control was supplied.; used 1 W11578571 (Controller) from stock
We serviced a
AMANA DRYER
Model NED4655EW1
Near Granby, Colorado 80446
Antonio
Job Details:
03/20/2025
Found burnt thermal fuse. Replaced thermel fuse then ran a cycle for proper operation and unit tested good ; used 1 WP3392519 (Thurmel fuse) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM09
Near Grants Pass, Oregon 97527
Thomas
Job Details:
03/20/2025
Light out in freezer per customer. This model does not appear to have a light bulb in it. Advised customer and let her know about survey
We serviced a
MONOGRAM RANGE
Model ZGU375NSD2SS
Near Colorado Springs, Colorado 80906
Jerimiah
Job Details:
03/20/2025
"Random igniters not igniting found burner heads and igniter partially corroded, explained how to clean burner heads and igniters for future use. Unit check ok charged service call $175.95 CC Auth# M9AW3H"
We serviced a
LG DRYER
Model DLEX8600BE.AEBEEUS
Near Colorado Springs, Colorado 80922
David
Job Details:
03/20/2025
"Checked dryer vent outside, not very good air flow, blower clear, took vent off back of machine, has good flow, a lot of back pressure when hooking vent back up."
We serviced a
COVE DISHWASHER
Model DW2450
Near Colorado Springs, Colorado 80919
Charles
Job Details:
03/20/2025
Replaced drier fan