We serviced a
WHIRLPOOL WALL OVEN
Model WOEC7030PZ01
Near Grand Junction, Colorado 81507
Clint
Job Details:
07/15/2026
Customer signed disclaimer and recieved parts ordered. Had to pull unit out from the wall to remove control panel. I only pulled it out about 5 inches removed the 2 screws replaced the board and put unit back in.Customer will watch and see if the display works properly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL RANGE
Model WFGS5030RZ0
Near Grand Junction, Colorado 81503
Clint
Job Details:
07/15/2026
"Customer signed disclaimer and recieved parts ordered. Installed new ignitor ,harness,and spark module. Unit ignited on first try and cycled perfectly. PLEASE TAKE TECH SURVEY THANKS.CLINT."
We serviced a
ELECTROLUX RANGE
Model ECCG3672AS
Near Colorado Springs, Colorado 80908
Earl
Job Details:
07/15/2026
I install the face plate and the grill and tested. It unit is operating properly at this time.
We serviced a
SUB ZERO REFRIGERATOR
Model DET3650CI/L
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
07/15/2026
installed listed parts and unit checked okay
We serviced a
KITCHENAID DISHWASHER
Model KDTS464SPS0
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
07/15/2026
"Door latch system is shorted out, removed and replaced, tested unit through diagnostics, working well now, verified by customer. Advised customer of situation and survey."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, Colorado 80920
Torrey
Job Details:
07/15/2026
Unit cycles heat from 140 to 220. Normal since there is a calculated 22 ft of ducting. Door gets hot because there is zero insulation in the door.
We serviced a
JENNAIR WALL OVEN
Model JMW2430IL02
Near Monument, Colorado 80132
Torrey
Job Details:
07/15/2026
Tech removed console and added spot welds of JBweld using the Whirlpool kit. Used a hair dryer to help the glue setup quicker for about 20 minutes. Reinstalled the console and asked the owner to not turn on the breaker for 24 hours to allow the glue to cure. Asked her to report back on the success of the repair. Cx called office to pay. I heard her over speaker phoneAuth code 4CMVH3 $219.95
We serviced a
WOLF RANGE
Model GR484DG-LP
Near Woodland Park, Colorado 80863
Charles
Job Details:
07/15/2026
"Replaced left & right griddle direct spark board, tested both griddles ignited"
We serviced a
JENNAIR RANGE
Model JGCP436HL02
Near Colorado Springs, Colorado 80908
Torrey
Job Details:
07/15/2026
Removed and replaced front panel. No scratches or dents. Cx approved. All burners test good. Owner took a picture of the model Serial as tag could not be detached.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS00
Near Albuquerque, New Mexico 87120
Tye
Job Details:
07/15/2026
Arrived and removed failed icemaker. Installed new icemaker. Informed cx of review.
We serviced a
KITCHENAID DISHWASHER
Model KDTS324SPS0
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
07/15/2026
"Water inlet assembly connection not fully secure, corrected and tested unit through diagnostics, working well now, no leaks. Advised customer of situation and survey."
We serviced a
JENN-AIR DISHWASHER
Model JDAF3924RX0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
07/15/2026
"Removed and replaced control and heat pump, tested unit through diagnostics, intermittently tripping in test 6, 15.0 resistance for heater, not grounded, discussed situation with techline, not grounded and pulling 3.6 and 4.4amps to the heater, unit does not trip when plugged into outlet for the other dishwasher. Advised customer of situation and survey. Case number 24218237"
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Albuquerque, New Mexico 87108
Jason
Job Details:
07/15/2026
Installed hub and tub ring ran spin cycle to test operation unit operation checkso ok. spoke to cx about review
We serviced a
MAYTAG DRYER
Model MED6630HW0
Near Albuquerque, New Mexico 87110
Jason
Job Details:
07/15/2026
Checked unit found element open. installed element ran timed dry cycle unit operation checks ok spoke to cx about review; used 1 WP3387747 (element) from stock
We serviced a
THERMADOR BI FREEZER
Model T30IF70NSP/09
Near Manitou Springs, Colorado 80829
Charles
Job Details:
07/15/2026
"Freezer 40 degrees, fan not running, upper panel full of ice, tested heater in diagnostic, drain frozen. Defrosted several inches of ice to pull evaporator cover to access drain Service fee $ 169.95, Labor $259.95, Total $$429.90 sent link for payment to owner, never received confirmation of payment. DID NOT COLLECT $, owner never signed and approved SEND BILL TO CUSTOMER"
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Fountain, Colorado 80817
David
Job Details:
07/15/2026
"Not working upon arrival, replaced control and UI. Tested and is operating as designed. Cx"
We serviced a
WOLF RANGE
Model n/a
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
07/15/2026
showed cust how to clean her ignitors and bases...autho no. w339rk
We serviced a
KITCHENAID MICROWAVE OVEN
Model KMBS730SPS00
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
07/15/2026
"Dent lower right of door, removed and replaced, no scratches or dents, verified by customer. Advised customer of situation and survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5300SR
Near Woodburn, Oregon 97071
Jesse
Job Details:
07/15/2026
"July 15 JG 1:43 PM, contacted client and informed her ETA 60 minutesConcern : left side fridge door was not closing properly due to mullion flap out of alignment. Machine fault not user error or install issue. Adjusted and re secured flap. Tested multiple times and had client test it to ensure they were happy they are."
We serviced a
SUB ZERO REFRIGERATOR
Model 590
Near Sherwood, Oregon 97140
Austin
Job Details:
07/15/2026
7/15/26 BA: removed and replaced master switch assembly with jumper kit. Unit is now powered on and compressors are running. Told Cx to wait up to 24hrs for proper temps and maybe longer for ice production. Condenser unit serviced as well. Service complete$229.95 CC Auth# U949AV
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Albuquerque, New Mexico 87109
Jason
Job Details:
07/15/2026
Checked unit found clip had come off of drain pump impeller and stopped impeller from rotating. removed clip ran cycle to test operation unit operation checks ok. spoke to cx about review
We serviced a
KITCHENAID WALL OVEN
Model KOEC630SPS00
Near Albuquerque, New Mexico 87111
Jason
Job Details:
07/15/2026
installed parts and adjusted fitment as much as possible. ran a few heat cycles unit operation checks ok at this time. cx to monitor if noise comes back. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
07/15/2026
Arrived anf cx complaint of not filling Called techline. Informed me of extra power feature. Washer is functioning now as designed. Case #24214154.
We serviced a
AMANA DRYER
Model NED4655EW1
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
07/15/2026
Arrived and cx complaint of not heating. Found failed thermal overload. Replaced and vhecked dtyer operation. Unit is functioning now as designed. Informed cx of review. ; used 1 Wp8573713 (Thermostat) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ14
Near Ashland, Oregon 97520
Kyle
Job Details:
07/15/2026
"Doors slightly miss aligned, fresh food side higher than freezer side to account for food and weight in door of fresh food. When adding food doors should line up. Called customer and advised them that after the load fresh food and doors are still miss aligned, give us a call to come put and adjust after weight is on doors. Unit is operating as intended."
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near Medford, Oregon 97504
Kyle
Job Details:
07/15/2026
Customer stated washer was not filling with water. Changed cycle to quick wash and tested. Unit is operating as intended.
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Medford, Oregon 97504
Kyle
Job Details:
07/15/2026
"Replaced dispenser assembly cover and tested, unit operating as intended. Ran HASS unit passed, submitted report."
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Pueblo, Colorado 81008
James
Job Details:
07/15/2026
Found loose wire at moisture sensor. Secured and tested ops ckok
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRAE2024AW6
Near Pueblo, Colorado 81005
James
Job Details:
07/15/2026
Installed ordered parts vacuumed unit down. Unit held vacuum. Charged unit. Unit started cooling
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LFTR1835VF3
Near Colorado Springs, Colorado 80911
Ralph
Job Details:
07/15/2026
installed parts and cust to monitor
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Los Lunas, New Mexico 87031
Larry
Job Details:
07/15/2026
Cx complaint - Not heating - Inspected unit and found the element open - Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW6157PB1
Near Los Lunas, New Mexico 87031
Larry
Job Details:
07/15/2026
CX complaint - Washer leaked - Inspected unit and found the clamp missing from inner drain hose - Secured drain hose and tested good - Unit is good to go - Survey mentioned
We serviced a
KITCHENAID DISHWASHER
Model KDTS324SPS0
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
07/15/2026
Arrived and cx complaint of not draining. Found failed drsin pump. Replaced snd Checked operation. Unit is functioning now as designed. Informed cx of review. ; used 1 W11462456 (Pump) from stock
We serviced a
FRIGIDAIRE DISHWASHER
Model FDPH431LAF0A
Near La Pine, Oregon 97739
Levi
Job Details:
07/15/2026
Replaced control board and tested all checks okay
We serviced a
SAMSUNG REFRIGERATOR
Model RF23A9071SG/AA
Near Colorado Springs, Colorado 80923
Mathew
Job Details:
07/15/2026
Found switch behind pitcher malfunctioning. Recommend housing replacement. QUOTE 7/15/2026LABOR: Refrigerator / Ice Machine switch (Samsung ? LOW end ? Tier 1) $199.95PART: Part DA97-17399F (shipping incl.) $284.70SERVICE CALL $149.95MPS $18.50SALES TAX (CO Springs rate ? parts only ? 8.2%) $23.35TOTAL $676.45
We serviced a
WHIRLPOOL RANGE
Model WFES3030RS2
Near Colorado Springs, Colorado 80907
Carlos
Job Details:
07/15/2026
"Wiring is incorrect, L1 and L2 have 120 and L2 and Neutral have 240."
We serviced a
GE DRYER
Model GTD48EASWWB
Near Timber, Oregon 97144
Austin
Job Details:
07/14/2026
7/14/26 BA: installed new door catch and tested machine. No further issues service complete
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRMG2272CF05
Near Hillsboro, Oregon 97124
Austin
Job Details:
07/14/2026
7/14/26 BA: CX complaint unit is still not cold or making ice. Tech removed the back panel to the freezer evaporator to find a bad frost pattern due to the door not closing properly In the past repairs. Tech cleared the frost pattern to reset and turned unit back on. Tech watch the frost pattern develop properly onto the evaporator. Tech advised customer that the ice maker needs additional time to make ice. If the unit does not get to temperatures by the following day then it has a sealed system issue and cost of repairs will be determined by warranty if the unit will be replaced or fixed.
We serviced a
ASKO WASHER
Model W6124X.W.U
Near Monument, Colorado 80132
Charles
Job Details:
07/14/2026
"Installed pulley, bearing, ring, washer and bolt. Ran spin cycle and rinse and spin with no noise."
We serviced a
ELECTROLUX DRYER
Model EFME517STT0
Near Monument, Colorado 80132
Charles
Job Details:
07/14/2026
"Rear rollers failed, need 5 roller assembly 134715900, Idler pulley 134793500, Service fee $159.95, Labor $249.95, MPS $14.50, Parts $674.20, $77.62, Tax $38.34, Total $1214.56, declined estimate paid service fee autho NNMK43"
We serviced a
WHIRLPOOL W/D STACKED UNIT
Model WTW8127LC1
Near Los Lunas, New Mexico 87031
Larry
Job Details:
07/14/2026
CX complaint - Washer not going through cycle - Inspected unit and found the slider failed - Replaced with TS and tested good - Unit is good to go; used 1 W10734521 (Slider) from stock
We serviced a
MAYTAG WASHER
Model MTW5605RW1
Near Colorado Springs, Colorado 80923
Earl
Job Details:
07/14/2026
"Custom scomplaint unit did not rinse out all the way left a lot of water in the clothes I arrived and checked units in diagnostic mode.The only code that would come up would be stuck button.I contacted Whirlpool, they ran me through the diagnostics.On the unit.No diagnostics came up.It came all the way through perfectly.Fine unit is operating properly at this time.I got a file number from whirlpool24198283"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRMC2273CF02
Near Colorado Springs, Colorado 80927
Earl
Job Details:
07/14/2026
"Customer's complaint unit, not making ice, I arrived and the unit was making ice. The other issue is they can't get the change filter light to turn off. It's because they have the wrong filter in the correct filter actually has a chip in it, I inform the customer they have to get the right filter with the chip in order for that to turn off."
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC503ESS01
Near Monument, Colorado 80132
Earl
Job Details:
07/14/2026
"Customers complaint refrigerator does not cool.I found that the evaporator was completely inundated with ice.I thought it out and found that the drain was plugged.We got it unplugged, finally, but everything back together.Customer paid authorization codeTHCA44"
We serviced a
WHIRLPOOL RESIDENTIAL REFR
Model WRS321SDHZ11
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
07/14/2026
Installed compressor charged cx will observe
We serviced a
WHIRLPOOL DRYER
Model RED4516FWO
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
07/14/2026
Cx paid in full Autho 3J9K4M
We serviced a
WHIRLPOOL STACK UNIT
Model WET4024HW0
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
07/14/2026
Installed washplate ran tests all ok
We serviced a
MAYTAG WASHER
Model MVWC465HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
07/14/2026
Installed agitator and hub ran tests runs all ok
We serviced a
GE DRYER
Model GTX22EASKWW
Near Colorado Springs, Colorado 80925
Mathew
Job Details:
07/14/2026
Found start switch not making contact. Adjust to make proper contact. Test op all okay. Unit working as expected.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSRIAA
Near Fountain, Colorado 80817
Mathew
Job Details:
07/14/2026
Found 81c code active. No power to compressor. Recommend replacing main and inverter at the same time. $149.95 CC Auth# F4M3PEQUOTE 7/14/2026PART: Part DA92-00763L (shipping incl.) $313.88PART: Part DA94-02663D (shipping incl.) $150.58LABOR: Refrigerator / Ice Machine control board (Samsung ? LOW end ? Tier 2) $239.95SERVICE CALL $149.95MPS $18.50SALES TAX (CO Springs rate ? parts only ? 8.2%) $38.09TOTAL $910.95
We serviced a
SAMSUNG RANGE
Model NE63A6511SS
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
07/14/2026
Found bad regulator. Switch regulator. Test op all okay. Left oven out of place as underneath oven was too dirty to slide anything back.
We serviced a
SAMSUNG RANGE
Model NE63A6511SS
Near Colorado Springs, Colorado 80910
Mathew
Job Details:
07/14/2026
Replace element. Test op all okay.
We serviced a
SAMSUNG DRYER
Model DVE45T3200WIA3
Near Colorado Springs, Colorado 80909
Mathew
Job Details:
07/14/2026
Found sock in blower wheel. Remove sock. Test op. All okay. $149.95 CC Auth# L39ECE
We serviced a
MAYTAG WASHER
Model MTW6200RR1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
07/14/2026
"Removed and replaced UI control, programmed and tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Monument, Colorado 80132
Aaron
Job Details:
07/14/2026
"Rollers are worn causing excessive movement, worn belt, approved onsite, removed and replaced components, cleared unit of lint, tested unit, working and heating well now. Repair kit $73.90Tax $6.06Supplies $18.50Hc $159.95Labor $209.95Total job $468.36Auth total job $468.36 #K9PLJY"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23R6201WWAA
Near Colorado Springs, Colorado 80921
Charles
Job Details:
07/14/2026
"Bin frozen in ice compartment. Unit has had ice compartment siliconed already. Frozen again. Needs Ice maker DA97-18859A, Service fee $249.95, Labor $199.95, MPS $14.50, Part218.30, Tax $11.13, Total $583.83, declined estimate paid service fee check #140 autho W3XXEY"
We serviced a
ELECTROLUX WASHER
Model EFLS627UIW1
Near Monument, Colorado 80132
Earl
Job Details:
07/14/2026
Install the shocks and tested at unit is operating properly at this time
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AFF
Near Grants Pass, Oregon 97526
Chris
Job Details:
07/14/2026
Replaced the evaporator fan motor and control board. Tested. The evaporator fan is working.
We serviced a
SAMSUNG RANGE
Model NX60A6511SS/AA
Near Grants Pass, Oregon 97526
Chris
Job Details:
07/14/2026
Replaced the hot surface igniter and tested.
We serviced a
GAGGENAU WALL OVEN
Model BO480613/05
Near Roseburg, Oregon 97471
Chris
Job Details:
07/14/2026
The oven isn't installed no power available. The UI control has a glass cover that is shattered un readable. The oven door is locked. TS says the only way to unlock it is to power it on and use the UI. Since the UI is so badly damaged that unlocking it is not possible. Therefore the oven isn't repairable Case # 4106511810.
We serviced a
BIG CHILL REFRIGERATOR
Model BC14TFRLX1
Near Roseburg, Oregon 97471
Chris
Job Details:
07/14/2026
Replaced the freezer door and tested.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFC2353AF9
Near Bend, Oregon 97702
Levi
Job Details:
07/14/2026
Customer stated that refrigerator seem to barely cool since the new compressor was put in. But as the days went on the unit got colder and finally produced ice. I hooked up and checked pressures on the sealed system and they seem to be adequate but there was not very much heat exchange on the condenser. I added a total of about 15 g of r600a to the system slowly and as I slowly added it I started the feel heat exchange occur on the condenser. Also slowly watched the temperature in the freezer drop. It started about 18? and by the time I was done it was down to 9? indicating the unit is cooling. Maybe I bumped my gauge when I was putting gas in so I did not fill it adequately to start with. Frost pattern and everything are checking good at this moment in time. If I need to come back I'll have to install a new filter dryer and completely recharge unit.
We serviced a
MAYTAG WASHER
Model MVWC416FW1
Near Fountain, Colorado 80817
Carlos
Job Details:
07/14/2026
Installed hub and actuator runs all ok
We serviced a
SAMSUNG WASHER
Model WA52DG5500AWUS
Near Pueblo, Colorado 81003
David
Job Details:
07/14/2026
"Checked washer, ran HASS, overall diagnostics passed, did have a 4C code, good water flow into machine. Ran a cycle and all ran as expected. Cx to monitor."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ14
Near Los Lunas, New Mexico 87031
Larry
Job Details:
07/14/2026
CX complaint - Not cooling proper - Inspected unit and found the fill tube misaligned and leaking onto the evap fan - Removed ice and adjusted fill tube - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHV05
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
07/14/2026
Arrived and cx complaint of left door not right. Flap isn't closing. Found door to be lower on left. Causing door glap not yo hit the channel.adjust door height. Doir glap is functioning now as designed.
We serviced a
SAMSUNG REFRIGERATOR
Model RF220NCTASR/AA
Near Colorado Springs, Colorado 80910
Brandon
Job Details:
07/14/2026
brandon@d3appliance.com - QUOTE 7/14/2026LABOR: Refrigerator / Ice Machine evap fan (Samsung ? LOW end ? Tier 2) $239.95PART: Part DA31-00334C (shipping incl.) $237.96SERVICE CALL $149.95MPS $18.50SALES TAX (CO Springs rate ? parts only ? 8.2%) $19.51TOTAL $665.87
We serviced a
SAMSUNG REFRIGERATOR
Model RF90F29AECRAA
Near Colorado Springs, Colorado 80907
Brandon
Job Details:
07/14/2026
Replaced evap cover and tested operation all checks ok hass passed
We serviced a
SAMSUNG MICROWAVE
Model ME17R7021ES/AA
Near Colorado Springs, Colorado 80909
Brandon
Job Details:
07/14/2026
"Found pcb broken, replaced pcb all checks ok"
We serviced a
DACOR REFRIGERATOR
Model DRF365300AP/DA
Near Frisco, Colorado 80443
Erik
Job Details:
07/14/2026
Connect to HASS Run diagnostic and icemaker test:pass
We serviced a
DACOR RANGE
Model DOB30M977DM/DA
Near Frisco, Colorado 80443
Erik
Job Details:
07/14/2026
Preheat oven to 400 degrees and let run for 30 min.UI panel is still warm/hot to the touch after 2 hoursCall dacor tag: engineering explains that panel can reach up to one hundred and fifty degrees.
We serviced a
KITCHENAID DISHWASHER
Model KDTS324SPS0
Near Santa Fe, New Mexico 87501
Jason
Job Details:
07/14/2026
Checked unit found unit was totally dead. installed control ran diagnostic cycle and started normal cycle a couple times unit operation checks ok. spoke to cx about review
We serviced a
MAYTAG DRYER
Model MGDE300VW3
Near Santa Fe, New Mexico 87507
Jason
Job Details:
07/14/2026
Checked unit found loose connection at valve coil causing it to cut out. re seated plug unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFF707ESS01
Near Santa Fe, New Mexico 87508
Jason
Job Details:
07/14/2026
Checked unit found machine cover toching condensor fan blade. corrected fitment of cover unit operation checks ok.spoke to cx about review
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ3
Near Aspen, Colorado 81611
Clint
Job Details:
07/14/2026
"Customer signed disclaimer and received parts ordered .installed new control and console, old console was peeling apart. Unit isn't mounted in the cabinet they are missing the mounting brackets.PLEASE TAKE TECH SURVEY THANKS.CLINT."
We serviced a
WHIRLPOOL DRYER
Model WHD560CHW2
Near Aspen, Colorado 81611
Clint
Job Details:
07/14/2026
Customer signed disclaimer and received parts ordered this was a stack unit in a hall way which was very difficult to work on.pulled front and tub out removed bback and installed new pump. Assembled unit and it ran perfectly. PLEASE TAKE TECH SURVEY.THANKS CLINT
We serviced a
WHIRLPOOL RANGE
Model WFES3330RZ2
Near Roseburg, Oregon 97471
Chris
Job Details:
07/14/2026
"Preheated the oven to 175 , when set a timer for 15 minutes to listen for random beeps during bake. Checked for error codes, none were found. No beeps after 15 minutes. Replaced door hinges."
We serviced a
FISHERPAYKEL DISH DRAWER
Model dd24dtx6i1
Near Aspen, Colorado 81611
Sean
Job Details:
07/14/2026
Verified the unit information customer signed disclaimer.Opened the unit and removed the wash rack and the filter screen from the bottom drawer. Removed the rotor assembly and installed the new one. Reassembled the unit and reset the controlled. Pulled the unit out and removed the water valve installed the new one . Reassembled the unit and put it back into place . Started the unit on an express wash .The unit started and ran the cycle.Watched the unit complete the wash . Tested the unit good.Thank you please fill out a technician survey.
We serviced a
THERMADOR REFRIGERATOR
Model T36BB925SS/30
Near Carbondale, Colorado 81623
Clint
Job Details:
07/14/2026
Cuatomer signed disclaimer and received parts ordered took door off and installed new rails had to adjust doors inward but they aren't rubbing any more the floor is a little warped . PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
BOSCH REFRIGERATOR
Model B36CL80SNS/46
Near Basalt, Colorado 81621
Sean
Job Details:
07/14/2026
Verified the unit information and customer signed the disclaimer. The unit goodRemoved the middle door and installed the new one onto the tracks. Reassembled the unit and tested
We serviced a
SAMSUNG WASHER
Model WA47CG3500AVA4
Near Medford, Oregon 97504
Kyle
Job Details:
07/14/2026
"Replaced main pcb and clutch assembly. Tested unit in spin only, unit is operating as intended. Performed HASS and unit passed, submitted report."
We serviced a
GE WASHER
Model GTW325ASWWW
Near Glenwood Springs, Colorado 81601
Clint
Job Details:
07/14/2026
Customer signed disclaimer a d recieved pump ordered. Pulled unit out and tilted it to install new pump. Took cover off and removed wiring and pump. Installed new pump put motor over back on and ran in wash and spin cycle . No noise was found and unit spun out perfectly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
LG DRYER
Model DLE1101V
Near Colorado Springs, Colorado 80919
Charles
Job Details:
07/14/2026
"Dryer overloaded due to washer not spinning, tested temperature, not overheating, unable to locate vent outside, does need vent cleaned. Service fee $109.95, paid check #4797 autho 9HMR99"
We serviced a
SUB ZERO REFRIGERATOR
Model 611/F-RH
Near Pueblo, Colorado 81001
Ralph
Job Details:
07/14/2026
REPLACED EVAP AND UNIT CHECKED OKAY..AUTHO NO. VL4X4X
We serviced a
GE RANGE
Model ZGP304NT2SS
Near Rifle, Colorado 81650
Sean
Job Details:
07/14/2026
Verified information customer signed disclaimer Removed the door and removed the door panel.unpackaged the new door panel and installed it on the door. Installed the door on the oven and tested the unit good.
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404KPS3
Near Colorado Springs, Colorado 80918
Torrey
Job Details:
07/14/2026
Removed and replaced rusted sump motor. Tested for function and leaks. All good.
We serviced a
KITCHENAID REFRIGERATOR
Model KBFO42FTX02
Near Colorado Springs, Colorado 80918
Torrey
Job Details:
07/14/2026
Found the left door top hinge was loose where the lever hits the door switch. Tightened and the lights come on everything now. Ice is being made in the ice bucket.$149.95 CC Auth# 93KT9T
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Colorado Springs, Colorado 80919
Charles
Job Details:
07/14/2026
"Will not spin, oil leaking from gear case, need gear case W11449840, splutch W10721967, belt WPW10006384, actuator W11481722, Service fee 149.95, Labor $259.95, MPS $18.50, Parts $320.20,$78.23,$62.43,$136.02, Tax $49.03, Total $1075.31, declined estimate paid service fee check #4797 autho 9HMR99"
We serviced a
BOSCH REFRIGERATOR
Model B36cl80ens/07
Near Hillsboro, Oregon 97124
Jesse
Job Details:
07/14/2026
"JG July 14 1042 am called eta 60 minsClient states his after market t-stat is showing fridge temp @ 55f and food is spilling quicker. States he has already replaced the door seals himself.Findings : clients t-stat is roughly 16f out of calibration and the true temp taken on site by tech is 39f nonissue with freezer or flex drawer. Fridge is overfilled with perishables leaving poor air flow performance to properly cool unit. Advised to follow units handbook on proper storage practices as well as pull unit away from wall for better breathing room of comp. No errors , alarms , or other issues found. Documented pre existing door damage.No machine fault found"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS06
Near Bend, Oregon 97701
Levi
Job Details:
07/14/2026
The knocking noise that the customer is hearing appears to be caused by thermal contractions and expansion during and after defrost cycle. I was not able to fully replicate noise but during diagnostics the unit made knocking sounds during defrost test and customer confirmed the noise was similar to what they have been hearing.
We serviced a
WHIRLPOOL DRYER
Model WED4307SW0
Near Bend, Oregon 97702
Richard
Job Details:
07/14/2026
Tested unit checked over tightened all screws double checked drum and rollers all testing fine at this time
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Carbondale, Colorado 81623
James R
Job Details:
07/14/2026
Replaced wire harnessbelt and splutch kit. Calibrated unit and then ran a service diagnostics test no issues. Unit is working as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
SAMSUNG WASHER
Model WF45T6000AW/A5
Near Medford, Oregon 97504
Kyle
Job Details:
07/14/2026
"Replaced main pcb and door latch assembly, tested unit on quick wash cycle. Unit operates as intended. Performed HASS and unit passed, uploaded report."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS01
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
07/14/2026
"E2 unable to find home position error code in diagnostics, dual water valve inlet line frozen, removed and replaced ice maker assembly and valve, tested unit through diagnostics, completed harvest and fill cycles, unit needs time to cool. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ4
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
07/14/2026
"Door gasket is allowing water to pass, removed and replaced, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ04
Near Colorado Springs, Colorado 80920
Aaron
Job Details:
07/14/2026
"Condenser fan motor is shorted out, removed and replaced, cleared condenser, unit needs time to adjust. Advised customer of situation and survey."
We serviced a
WHIRLPOOL FREEZER
Model WRQA59CNKZ01
Near Colorado Springs, Colorado 80918
Aaron
Job Details:
07/14/2026
"Customer states ice tastes like plastic, ice maker is able to compete harvest cycle, temperatures are good at time of inspection, all food is packaged well in the FC, this unit does not have a reservoir or water dispenser, only inlet valve and water tube to the ice maker, unit is hooked to a plastic water water line, and water sits in line until ice maker calls for water, recommend stainless steel braided water line. Advised customer of situation and survey."
We serviced a
JENN-AIR RANGE
Model JDRP548HL01
Near Breckenridge, Colorado 80424
Antonio
Job Details:
07/14/2026
Installed new cooling fans and ui panel then heated oven to 350 degrees for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFC5236RZ00
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
07/14/2026
"Removed and replaced control, cleared clogged defrost drain , unit needs time to cool, customer to monitor. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRSF5536RZ00
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
07/14/2026
Arrived and cx complaint of not cooling found loose wire at main board. Unit is functioning now as designed.