We serviced a
KITCHENAID RANGE
Model KSGB900ESS8
Near Avon, CO 81620
Antonio
Job Details: 05/03/2023
installed new slide both left and right
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW2
Near Colorado Springs, CO 80938
Aaron
Job Details: 05/03/2023
"Replaced control and tested unit, working well now, remounted dryer, all checks out ok. Balance fue was already paid. Advised of survey."
We serviced a
SAMSUNG DISHWASHER
Model DW80R5060UG/AA
Near Colorado Springs, CO 80926
Jeremy
Job Details: 05/03/2023
Leak due to damage. Back top damage caused seam to open (see attachments). Called Samsung tech support and was told not covered by warranty and is unrepariable. Returning all parts provided. Unable to run HASS due to damage and leak.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT138FFDW01
Near Colorado Springs, CO 80921
Jeremy
Job Details: 05/03/2023
KK trained me on compressor and evap coil install.
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9071SR/AA
Near Colorado Springs, CO 80925
Brandon
Job Details: 05/03/2023
Leveled fridge so all doors stay open now hass passed cx not available to sign
We serviced a
SUBZERO REFRIGERATOR
Model IC-36R
Near Colorado Springs, CO 80921
Jessie
Job Details: 05/02/2023
"- CUSTOMER NOT HERE TO SIGN WAIVER- REPLACED DOOR, TEST OP, ALL OK"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Glenwood Springs, CO 81601
James R
Job Details: 05/02/2023
Put into diagnostics there are no error codes. Went thru cycle no error codes. Unit is agitating and spinning. But when it does can here a bit of a noise. Tilted back and found pulley nut loose put on blue loctite and retightened. Noise went away. Put into normal wash deep water cycle. Filled up to agitator 8 inch depth. Agitator is attached properly. Canceled cycle and did a bulky items cycle. deep water wash. Filled up to top of agitator 13 inches. Normal level. Unit is operating as designed. Customer needs to not overload 1/2 - 3/4 full no more. SR# 7736307804
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Colorado Springs, CO 80921
Glenn
Job Details: 05/02/2023
Install New Console & UI Control. All OPS Test:OK
We serviced a
KITCHENAID RANGE
Model KSGB900ESS5
Near Colorado Springs, CO 80924
Glenn
Job Details: 05/02/2023
"Adjust Ignitor, Install New Burner Head Assy. All OPS Test:OK"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MW0
Near Santa Fe, NM 87505
Jason
Job Details: 05/02/2023
checked unit found supply line for surface burners was loose tightened and rechecked unit no leaks unit checks ok
We serviced a
WHIRLPOOL WASHER
Model MHW5630HW3
Near Albuquerque, NM 87110
Larry
Job Details: 05/02/2023
"CX complaint - Washer won,t drain - Inspected unit and found obstruction in drain pump - Removed water and cleared obstruction and tested good - Unit is good to go - Collected $355.88-auth-H4W4K4Trip-$129.95Labor-$199.95Tax-$25.98"
We serviced a
WOLF RANGE
Model DF48850/S/P
Near Colorado Springs, CO 80907
Jerimiah
Job Details: 05/02/2023
Installed replacement parts. Unit check ok.
We serviced a
SAMSUNG DRYER
Model DVE50BG8300VA3
Near Pueblo, CO 81003
Brandon
Job Details: 05/02/2023
Completed and sent RRR
We serviced a
WHIRLPOOL DISHWASHER
Model MDB8959SKZ0
Near Peyton, CO 80831
Aaron
Job Details: 05/02/2023
"Circulation motor is shorted out, only fills and drains, leak was coming from the spray arms trying to push. Circulation motor w11416362 $292.16Tax $23.96Supplies $14.50Hc $129.95Labor $189.95Total job $650.5230 day estimateNo return on partsAuth 129.95 hc #993F9C"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Florissant, CO 80816
Ken
Job Details: 05/02/2023
Installed cb and calibrated. Tested and unit works properly
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FSS02
Near Colorado Springs, CO 80906
Ralph
Job Details: 05/02/2023
"unti nhas a broken ice bucket, cust to order parts and call once he wants me to install them...cust paid total autho no 4E9C9P"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Rifle, CO 81650
James R
Job Details: 05/02/2023
Replaced slider. Test in diagnostics DLMS calibration. Ok. Run thru a diagnostics cycle. Op's normal.Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
FRIGIDAIRE DISHWASHER
Model FDPC4221AB0A
Near Colorado Springs, CO 80922
Jessie
Job Details: 05/02/2023
"- REPLACED SOAP CUP, TEST OP, ALL OK"
We serviced a
WHIRLPOOL WASHER
Model WFW9150WW01
Near Los Lunas, NM 87031
Larry
Job Details: 05/02/2023
CX complaint - Smells like burning - Inspected unit and found the main bearings failed and the UI failed - UI is NLA unit is unrepairable - Called Safety Team (SR7736310215)
We serviced a
KITCHENAID MICROWAVE
Model KMBP107ESS03
Near Blue River, CO 80424
Antonio
Job Details: 05/02/2023
installed new door switch unit tested good Labor $169.00 AUTH#44393W
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Colorado Springs, CO 80907
Ralph
Job Details: 05/02/2023
installed ice mkr kit and uit checked okay
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SR/AA
Near Pueblo, CO 81005
James
Job Details: 05/02/2023
"Found power cord chewed from rats potentially. Needs power cord 3903-001003 103.86+tax, sc 129.95, labor 129.95, mps 14.50. Total: 386.78 cust declines at this time collected 129.95 $129.95 CK Auth# 3PL34L"
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9671SR/AA
Near Colorado Springs, CO 80904
Jonny
Job Details: 05/02/2023
"Installed part's, hass passed, no more water leaking in fridge."
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAESR/AA
Near Colorado Springs, CO 80927
Brandon
Job Details: 05/02/2023
"Replaced ice maker, pcb, drain tube sealed ice room reset ice maker it cycled tested op all ok hass not compatible"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ08
Near Albuquerque, NM 87114
Joseph
Job Details: 05/02/2023
Installed part listed and fuse. Unit tested good. Unit is good to go.; used 1 WPM0805101 (Fuse) from stock
We serviced a
MAYTAG WASHER
Model MVWC465HW3
Near Rio Rancho, NM 87124
Joseph
Job Details: 05/02/2023
Installed parts listed. Unit tested good. Unit is good to go.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Rio Rancho, NM 87144
Joseph
Job Details: 05/02/2023
Installed parts listed. Unit tested good. Unit is good to go.
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS04
Near Rio Rancho, NM 87144
Joseph
Job Details: 05/02/2023
Installed parts listed. Unit tested good. Unit is good to go.
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950UG/AA
Near Colorado Springs, CO 80924
Jeremy
Job Details: 05/02/2023
Top spray arm wont stay attached. Water wall arm broke off. Used parts from prediagnosis. Issue fixed. Ran HASS. Double checked for leaks and placed leak detection strip under unit. Asked CX to cimoplete the survey.
We serviced a
MAYTAG RANGE
Model MGR6600FZ2
Near Rio Rancho, NM 87144
Joseph
Job Details: 05/02/2023
Unit giving F6E1 error code. Issue with control manager. Unit is not shutting off the oven and will keep running. Inspect unit. Unit will need a new control W11449506 and regulator W11449506 Called whirlpool safety team. They will be covering parts and labor. Let manager Rick know and a new ticket will be made with the pets ordered.Autho: M16X9B1WPL1Case #7736289315
We serviced a
KITCHENAID MICROWAVE
Model KMBP107ESS03
Near Blue River, CO 80424
Antonio
Job Details: 05/02/2023
installed new door switch unit tested good Labor $169.00 AUTH#44393W
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT148FZDM04
Near Breckenridge, CO 80424
Antonio
Job Details: 05/02/2023
found loose conection to compressors relay. reconnected unit tested good
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW0
Near Albuquerque, NM 87105
Larry
Job Details: 05/02/2023
Cx complainbt - F6E2 and no controls work - Inspected unit and found Comms error - Unit needs controls - Cx Wants to discuss with husbend - Collected $140.18-Auth-9J43ECConsole- W11319991 - $272.76Control- W11322903 - $361.92Labor- $159.95Tax- $62.58Total - $857.21
We serviced a
SAMSUNG REFRIGERATOR
Model RF22R7351SR/AA
Near Calhan, CO 80808
Jonny
Job Details: 05/02/2023
"Installed parts, hass wouldn't work so I called the number. Custy will have ice in 24 hours"
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SR/AA
Near Colorado Springs, CO 80922
Brandon
Job Details: 05/02/2023
"Replaced ice maker, pcb, drain heater, sealed ice room hass passed reset ice maker it cycled tested op all ok"
We serviced a
SAMSUNG GAS RANGE
Model NX60A6311SS/AA
Near Colorado Springs, CO 80925
Brandon
Job Details: 05/02/2023
Adjusted broil burner tube gas spilling out
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Woodland Park, CO 80863
Ken
Job Details: 05/02/2023
Installed run capacitor and tested. Machine is operating properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model MFI2570FEZ12
Near Monument, CO 80132
Glenn
Job Details: 05/02/2023
Install New Valve. All OPS Test:OK
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAESR/AA
Near Colorado Springs, CO 80923
Jonny
Job Details: 05/02/2023
"Installed parts,mass wouldn't connect so called the number, custy will have ice in 24 hours"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA8
Near Colorado Springs, CO 80920
Amos
Job Details: 05/02/2023
Hoss Still won't go through tried several times. Replaced all parts listed.
We serviced a
WHIRLPOOL RANGE
Model WFG515S0MS0
Near Monument, CO 80132
Glenn
Job Details: 05/02/2023
"Glides Installed, showed customer how drawer works. No Rails on this style range."
We serviced a
KITCHENAID RANGE
Model KFDC558JBK01
Near Monument, CO 80132
Glenn
Job Details: 05/02/2023
"RF Burner not igniting properly. Adjust burner head assy. Suggest Both LF & RF Burners are High Flow, slowly turn control to flame icon, and back turn to ignite. ALL OPS Test:OK"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT148FZDM04
Near Breckenridge, CO 80424
Antonio
Job Details: 05/02/2023
found compressor pulling 10.9 amps on start up called whlp unit is up for review AUTH# SR7736308873
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Dillon, CO 80435
Antonio
Job Details: 05/02/2023
installed new gasket unit tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ00
Near Glenwood Springs, CO 81601
James R
Job Details: 05/02/2023
When i arrived tenant indicated frig has been working great. Unplugged unit once plugged back in it evidently reset and has been working good. Removed unit removed access panel checked all electrical connections. All connected good. Condenser and evapoprator fans are running. Cooling good. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
THERMADOR COOKTOP
Model PSC486GDZS/02
Near Colorado Springs, CO 80906
Jerimiah
Job Details: 05/02/2023
"Griddle thermostat broken, constantly sending power and fuel to griddle burner in off position. Both possible parts are on their way to discontinued if not already. Disabled griddle thermostat. Other burners working fine. Charged service call $149.95 chk#565300424764 thermostat NLA00618624 DSI board backordered."
We serviced a
SAMSUNG WASHER
Model WF42H5000AW/A2
Near Colorado Springs, CO 80911
Jeremy
Job Details: 05/02/2023
Debris caused pump to stop pumping. Unclogged pump. Unit is now working correctly. Educated CX on using Affresh and running clean cycle. Double checked for water leak and placed leak detection strip under unit.
We serviced a
WOLF RANGE
Model DF48850/S/P
Near Colorado Springs, CO 80907
Jeremy
Job Details: 05/02/2023
Helped JC with range
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JVM7195EK6ES
Near Colorado Springs, CO 80905
Jerimiah
Job Details: 05/02/2023
"Installed replacement parts, unit check ok, Cust will keep track of 7nit functionality."
We serviced a
KITCHENAID WALLOVEN
Model KGRS505XWH05
Near Peyton, CO 80831
Aaron
Job Details: 05/02/2023
"Lower oven is not lighting, verified power to the igniter, replaced igniter and tested, heating well now. Auth 169.95 labor #43JH3U"
We serviced a
WHIRLPOOL RANGE
Model WFG550S0HZ2
Near Colorado Springs, CO 80924
Aaron
Job Details: 05/02/2023
"Top burners and bake burner are lighting and working well, burner tube is not fully engaged for broil. Needs gas valveValve w11449506 $178.98Tax $14.68Supplies $14.50Hc $129.95Labor $179.95Total job $518.0630 day estimateNo return on partsAuth 129.95 #44TALU"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Aspen, CO 81611
James R
Job Details: 05/02/2023
Unit fills with water. Then just doesnt circulate water. Removed outer panel checked connections at control. removed and reinstalled. checked connection at circulation motor pump asy. Reassembled and it started working. Is running normal at this time. Evidently a faulty connection. Put into diagnostics to recalibrate and test functions of unit. Op's good. customer paid service call $149.95 auth code. UC4Y3P
We serviced a
JENNAIR BUILT-IN M/W
Model JMC8127DDS
Near Snowmass Village, CO 81615
James R
Job Details: 05/02/2023
Piece that turns turn table is melted and metal base is burnt. Has turned surface black. called tech line.Cleaned up surface of MW cabinet where coupler sets. Put coupler back in place. Put a glass of water next to it. Turned MW on Turn table is turning but can see that coupler is arcing. Removed coupler turned on again no arcing and glass of water got hot. Issue is with the turntable coupler. R0130605 when look up part shows discontinued. Put turn table glass in place and glass of water no arching heats good. Customer needs to contact safety team for a resolution to the issue. 1-866-550-5136Please fill out whirlpool tech satisfaction survey. Thank You.customer not available to sign ticket.
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Monument, CO 80132
Glenn
Job Details: 05/02/2023
"Very Long Drying times. Found restricted Vent System. Very long cooling times = Long Dry times.Customer paid SC fee of $129.95, Autho# 49PY34"
We serviced a
GENERAL ELECTRIC RANGE - GAS
Model PGB935YP2FS
Near Pueblo, CO 81008
James
Job Details: 05/02/2023
Installed ge supplied handle. All ops test good.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Pueblo West, CO 81007
James
Job Details: 05/02/2023
Installed ordered parts all ops test good. Left litmus (see sd pics)
We serviced a
JENNAIR OVEN
Model JJW2830IM00
Near Dillon, CO 80435
Antonio
Job Details: 05/02/2023
AUTH for extra labor J16X8D0AL2 installed new thermol cutt off unit tedsted good
We serviced a
WHIRLPOOL DISHWASHER
Model WDT710PAHZ1
Near Colorado Springs, CO 80924
Aaron
Job Details: 05/02/2023
"Main control board is shorted out, terminal burnt to UI assembly, needs control and UI.Control board w11306302 $264.44UI control w11402115 $134.20Control to UI harness w11028004 $33.87Total parts $432.51Tax $35.47Supplies $14.50Hc 2 of 2 $89.95Labor $ 179.95Total job $752.383o day estimateNo return on partsAuth 89.95 hc #33HAR9Advised customer of 5 star survey"
We serviced a
WHIRLPOOL RANGE
Model KFEG500EWH6
Near Albuquerque, NM 87107
Larry
Job Details: 05/02/2023
CX complaint - Convection fan not working - Inspected unit and found loose connection to the fan - Secured connection and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model MEDB835DW4
Near Monument, CO 80132
Glenn
Job Details: 05/02/2023
"Found locked up idler pulley. Install New Kit: Support Rollers, Pulley wheel & Belt. Might also eventually require Idler Pulley - W10837240 $67.10.All OPS Test:OK, Suggest Cleaning Vent system once per year. Paid In Full $395.28 + Tip $19.76 = $415.04"
We serviced a
WHIRLPOOL WALLOVEN
Model WOC75EC0HS04
Near Santa Fe, NM 87505
Jason
Job Details: 05/02/2023
installed t-stat unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Colorado Springs, CO 80917
Aaron
Job Details: 05/02/2023
"Circulation motor is shorted out, rest of unit is in good condition, unit only fills and drains. Needs motor assembly. Circulation motor W11025157 $288.78Tax $23.68Supplies $14.50Hc $129.95Labor $189.95Total job $646.8630 day estimateNo return on partsWith 129.95 hc #"
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Colorado Springs, CO 80917
Aaron
Job Details: 05/02/2023
"F8E1 long fill and F8E3 internal water overflow error codes upon arrival, capacitor is humming and actuator is not engaging, replaced parts and tested init through diagnostics, working well now. Advised customer of 5 star survey"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, CO 80925
Carlos
Job Details: 05/02/2023
Harness is burned and needs to be replace in order for heating element to defrost. Customer will call back. They are debating if the just want to get a new fridge. Harness is under 1 year warranty on parts. Cx paid service call $129.95 CC Auth# 9XWC3U
We serviced a
WHIRLPOOL FREEZER
Model WZC5216LW0
Near Monument, CO 80132
Jessie
Job Details: 05/02/2023
#NAME?
We serviced a
SPEEDQUEEN DRYER
Model ADGE9RGS115TW01
Near Monument, CO 80132
Jessie
Job Details: 05/02/2023
"replaced ng orfice, test op, all ok"
We serviced a
GENERAL ELECTRIC WASHER
Model GTW335ASN2WW
Near Colorado Springs, CO 80904
Kris
Job Details: 05/02/2023
installed struts ran test op all ok unit is working to spec at this time.
We serviced a
FRIGIDAIRE REFRIGERATOR SID
Model FFHS2311LWEA
Near Colorado Springs, CO 80923
Kris
Job Details: 05/02/2023
installed all parts sent ran test op all ok.
We serviced a
GE REFRIGERATOR
Model GSS25LSLRCSS
Near Colorado Springs, CO 80921
Kris
Job Details: 05/02/2023
rc temp@30.1 rc temp@41.7 compressor is only drawing 0.3 amps. compressor is hot to touch all fans and light are working. cx does not want to go through with repair.
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC704FPS05
Near Colorado Springs, CO 80921
Kris
Job Details: 05/02/2023
installed all parts sent ran test op all ok unit is working to spec at this time.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHB00
Near Fountain, CO 80817
Carlos
Job Details: 05/02/2023
Wire harness on bottom of door is broken. Customer wants to repair themselves . Cx paid service call $129.95 CC Auth# 44FK4C
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Colorado Springs, CO 80904
Carlos
Job Details: 05/02/2023
Installed listed parts. ran test op runs ok
We serviced a
JENNAIR REFRIGERATOR
Model JFFCC72EFS00
Near Colorado Springs, CO 80919
Ralph
Job Details: 05/02/2023
replaced listed parts and cust to monitor unit
We serviced a
KITCHENAID REFRIGERATOR
Model KBLC36MHS01
Near Colorado Springs, CO 80904
Ralph
Job Details: 05/02/2023
replaced part and unit cycled and filled cust to monitor
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, CO 80904
Ralph
Job Details: 05/02/2023
installed vallve and unit checked okay
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Carbondale, CO 81623
James R
Job Details: 05/02/2023
put unit into diagnostics test 12 ok. No error codes. removed rear panel. checked motor windings all 15.1-15.3 ok. called tech line. unable to determine anything again. Each time there are no error codes. Want customer to wait and let cycle complete. Dont cancel cycle and put into drain and spin. Unit will try to balance the load a number of times. Once it does it will spin. Load can create a issue that if it is out of balance enough it wont spin properly. Put into quick wash unit went thru just fine. No load. Sounds fine. bearings of basket are good. Drains good. Tech line wants for a error code to come up to indicate a issue. Put a water board under unit. Also had waiver signed. SR# 7735782949
We serviced a
SUBZERO REFRIGERATOR
Model 680/F
Near Elbert, CO 80106
Kris
Job Details: 05/01/2023
fc temp@19.3 ran test op unit has a leak in evap cx is deciding on repair 7019631 evap 296.797002026 compressor 357.38
We serviced a
WHIRLPOOL DRYER
Model WGD5800BW0
Near Colorado Springs, CO 80919
Jeremy
Job Details: 05/01/2023
Dryer making noise during operation. Debris in blower housing causing noise. Cleaned housing and inside of cabinet. Unit sounds good. Recommend CX get dryer vent cleaned. Service Charge $129.95 Labor $96.95 Total $226.90 Auth: V3Y9VX
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HFEDBBC/AA
Near Colorado Springs, CO 80911
Jeremy
Job Details: 05/01/2023
Ice maker/ auger frozen over. Replaced all new parts. Ice maker working to the best of knowledge. Double checked leaks. Placed leak detection strip under unit. Asked CX to complete the survey.
We serviced a
WHIRLPOOL DRYER
Model CGM2745FQ0
Near Bernalillo, NM 87004
Joseph
Job Details: 05/01/2023
Cleaned unit. Found that the ducting was not hooked up. And the ducking runs behind a stacked unit so I couldnt hook it up for them. Let them know to hook up the ducting and it will be good to go.
We serviced a
SAMSUNG DRYER
Model DVE45R6100C/A3
Near Peyton, CO 80831
Jonny
Job Details: 05/01/2023
"Heating element is bad, will order new one, no contuityHeating assy dc97-14486a 200.00Sf 129.95 Labor 159.95 Autho#99mr9tTruck part"
We serviced a
SAMSUNG REFRIGERATOR
Model RF25HMEDBSR/AA
Near Colorado Springs, CO 80920
Jonny
Job Details: 05/01/2023
"Installed parts, not hass compatible, fridge will have ice in 24 hours"
We serviced a
SAMSUNG WASHER
Model WF45A6400AV/US
Near Pueblo West, CO 81007
Brandon
Job Details: 05/01/2023
"Broken weight, need weights, bolts and nuts and front tub. Cx said unit is in warranty, got POP. Svf will be charged to cx if unit is not covered, cx would not pay svf"
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Rio Rancho, NM 87144
Joseph
Job Details: 05/01/2023
Leaking. Inspect unit and ran diagnostics. Found piece of cotton at front bottom of the unit behind the front panel. When water was spraying it would soak the cotton and leak water out. Took out the piece of cotton. Unit tested good. Unit is good to go. Had customer sign the water disclaimer and also I did put a leak strip at the bottom of the unit.
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Tijeras, NM 87059
Jason
Job Details: 05/01/2023
installed control and calibrated for wash performance. unit checks ok
We serviced a
GENERAL ELECTRIC DRYER
Model QFD15ESSN1WW
Near Colorado Springs, CO 80910
Ken
Job Details: 05/01/2023
Installed parts and tested with out vent hooked up and was fine. Called ge to note and verify all is good. Did diag test with no vent hooked up and took 5 mins to reach 200f. Hooked up vent did same test and went to 210 in 45-50 seconds. Dryer has vent issue. Advised customer duct is not clean or is too long
We serviced a
GE DISHWASHER
Model HDF330PGR3WW
Near Glenwood Springs, CO 81601
Erik
Job Details: 05/01/2023
install/test: GOODJOB COMPLETE!
We serviced a
GENERAL ELECTRIC WASHER
Model GFW550SSN2WW
Near Colorado Springs, CO 80906
Ken
Job Details: 05/01/2023
Installed parts and tested
We serviced a
KITCHENAID OVEN
Model KODE500ESS20
Near Albuquerque, NM 87113
Larry
Job Details: 05/01/2023
Installed door glass and tested good - Unit is good to go
We serviced a
MONOGRAM RANGE
Model ZGP486NDTSS
Near Carbondale, CO 81623
Erik
Job Details: 05/01/2023
NEEDS LP
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ4
Near Albuquerque, NM 87113
Larry
Job Details: 05/01/2023
Installed harnesses and tested good - Unit is good to go
We serviced a
GENERAL ELECTRIC WASHER
Model PTW600BSR1WS
Near Colorado Springs, CO 80906
Ken
Job Details: 05/01/2023
Installed tub and springs.. tested machine and it is working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SMHZ02
Near Peyton, CO 80831
Aaron
Job Details: 05/01/2023
"Control is not responding to the UI, settings are at 7 for freezer (coldest), and 4 for refrigerator, temperatures at time of inspection are 1f for freezer and 39.5f for RC, explained to customer how the airflow for the refrigerator works, top back will be coldest area. Wpw10503278 $232.84Tax $19.09Supplies $14.50Hc $129.95Labor $169.95Total job $566.33Approved on site , replaced board and programmed, left settings at 4 and advised customer, confirmed that settings can be adjusted. No return on partsAuth total due $566.33 #3MK3TP"
We serviced a
KITCHENAID WALLOVEN
Model KODE500ESS20
Near Colorado Springs, CO 80908
Aaron
Job Details: 05/01/2023
"Customer states that the unit works fine for quick cooks like pizza etc, has trouble for longer cooks, stated that unit would not go past 365f, tested upper and lower ovens at 400f, upper oven avg temp 376f and lower 393f after 45 minutes of heating, called techline and calibrated upper oven 20 degrees. Unit is working well, blower pushing well, advised customer of calibration."
We serviced a
KITCHENAID RANGE
Model KSDB900ESS5
Near Grand Junction, CO 81507
James R
Job Details: 05/01/2023
Replaced slides and drawer. Slides in and out normally. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SAMSUNG REFRIGERATOR
Model RF4287HARS/XAA
Near Pueblo West, CO 81007
James
Job Details: 05/01/2023
"Installed ordered part, de-iced defrost drain. Tested ops all ckok. Left litmus (see sd pics)"
We serviced a
MAYTAG WALLOVEN
Model MEW9530DS00
Near Grand Junction, CO 81507
James R
Job Details: 05/01/2023
No pwr. removed control panel. checked thermal fuse it is blown. jumped across and test unit functions bake broil convection op's ok. need to replace fuse and blower. $480.51 plus 298.00 labor to repair. total $778.51 to repair.Paid service call $149.95 auth code 44PCXV
We serviced a
MAYTAG WASHER
Model MED4500MW0
Near Albuquerque, NM 87112
Jason
Job Details: 05/01/2023
checked unit found unit needed calibration re- calibrated unit for wash performance unit checks ok
We serviced a
GE REFRIGERATOR
Model GTE18GTNDRWW
Near Aspen, CO 81611
Erik
Job Details: 05/01/2023
install/test: Rumble is no longer presentJOB COMPLETE!
We serviced a
MIDEA WASHER
Model MLV45N3BWW
Near Pueblo, CO 81003
James
Job Details: 05/01/2023
"Found basket bolts backing out of gc causing basket to wobble. Secured with loctite and tested, ops ckok. Left litmus (see sd pics)"