We serviced a
SAMSUNG DRYER
Model DV42H5200EP/A3
Near Elbert, CO 80106
Brandon
Job Details:
11/07/2023
"Unit not heating, element tested bad,Svf paid $129.95 Auth# KEN4P4,Dc47-00019a $133,Labor $189.95,Svf $129.95,Mps $14.50,Tax $10.91"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRSS2652AF3
Near Colorado Springs, CO 80908
Jessie
Job Details:
11/07/2023
I was able to verify the issue I found the controls wiring connection was detached I was able to connect harness to ui control and unit began functioning as designed
We serviced a
MIDEA DISHWASHER
Model MDT24H3AST
Near Pueblo, CO 81006
James
Job Details:
11/07/2023
found power connection to unit loose causing arching and melting of wires. cut out affected area and reconnected all ops test good.
We serviced a
THERMADOR DOWNDRAFT VENT
Model CVS36RB
Near Pueblo, CO 81008
James
Job Details:
11/07/2023
found motor for telescoping failed. parts nla collected 149.95 $149.95 CK Auth# LM4E4T
We serviced a
KENMORE DRYER
Model 110.65962400
Near Pueblo, CO 81005
James
Job Details:
11/07/2023
installed ordered parts all ops test good
We serviced a
COVE DISHWASHER
Model DW2450
Near Colorado Springs, CO 80907
Ralph
Job Details:
11/07/2023
"subzero said that the door panel is too low has to be 4 inches form the floor and this one is about 3.1 inches, cust to call her cabinet guy"
We serviced a
SAMSUNG DRYER
Model DVE55A7300E
Near Pueblo, CO 81005
James
Job Details:
11/07/2023
found dent in side of unit causing insulation to rub and stick once cooled. removed melted insulation and pushed out dent unit no longer rubs when running.
We serviced a
WHIRLPOOL RANGE
Model WFC310S0AB0
Near Pueblo, CO 81003
David
Job Details:
11/07/2023
Replaced handle and door vent All good
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS
Near Colorado Springs, CO 80909
Carlos
Job Details:
11/07/2023
Installed igniter ran test op all ok
We serviced a
JENN-AIR RANGE
Model JDS1750ES1
Near Pueblo, CO 81005
James
Job Details:
11/07/2023
cust complaint of unit shutting off when light button pressed. preheated oven and tested all ops ckok. potentially needs ui but all ops tests fine. no error codes. collected 169.95 $169.95 CC Auth# M43YTP
We serviced a
SAMSUNG MICROWAVE
Model ME17R7021ES/AA
Near Pueblo West, CO 81007
James
Job Details:
11/07/2023
found loose wire at turntable motor causing intermittent noise secured and tested. Ops ckok. also found unit doesn't fit properly where/how its installed. its causing unit to overheat from poor ventilation. see quick pics. advised cust.
We serviced a
SAMSUNG REFRIGERATOR
Model RF323TEDBSR/AA 06
Near Pueblo West, CO 81007
Jeremy
Job Details:
11/07/2023
Installed all ordered parts. Ice maker working to the best of my knowledge. Not HASS compatiable. I asked cx to complete the survey.
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Pueblo West, CO 81007
Jeremy
Job Details:
11/07/2023
Brought microwave leakage detector with me. Contacted tech support. After many pictures and leakage test Samsung tech support said the quality incident report will be sent to the engineering department for review. I will contact CX with report.
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Colorado Springs, CO 80909
Brandon
Job Details:
11/07/2023
"No errors, Ice bucket stuck, ice route failed water hold test, replaced ice route and ice tray, reset ice maker, tested op all ok hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RT18M6215SR/AA
Near Colorado Springs, CO 80909
Brandon
Job Details:
11/07/2023
"Replaced compressor and dryer, held vacuum for 15 minutes, charged unit, compressor is removing heat, cx will monitor"
We serviced a
BOSCH DISHWASHER
Model SHEM3AY55N/28
Near Colorado Springs, CO 80905
Ralph
Job Details:
11/07/2023
installed parts and unit checked okay
We serviced a
FISHERPAYKEL DISHWASHER
Model DD24DDFX6V2
Near Colorado Springs, CO 80906
Ralph
Job Details:
11/07/2023
installed part and unti checked okay
We serviced a
MAYTAG DRYER
Model MED6630HW2
Near Carbondale, CO 81623
James R
Job Details:
11/07/2023
"Put a dryer kit in unit. Much better. Cleaned unit. Also put a cutoff thermal in unit as well. Is heating good. Customer signed waivers.Please fill ouit whirlpool tech satisfaction survey. Thank You.; used 1 4392067 (Dryer Kit (4 Roller)), and 1 280148 (CUTOFF-TML) from stock"
We serviced a
AMANA REFRIGERATOR
Model ART308FFDB11
Near Colorado Springs, CO 80915
Carlos
Job Details:
11/07/2023
Called tech line 7737734977. Refrigerator has internal leak. Cannot be repair. Whirlpool will contact cx
We serviced a
GE WASHER
Model GFW148SSM0WW
Near Vail, CO 81657
Erik
Job Details:
11/07/2023
BAD INSTALL
We serviced a
MAYTAG DRYER
Model MEDC215EW1
Near Woodland Park, CO 80863
Mathew
Job Details:
11/07/2023
"Bad thermal fuse. Called safety, repair not covered. Svf $129.95 Cx replacing unit. $129.95 CC Auth# F9RE9T"
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Rio Rancho, NM 87124
Larry
Job Details:
11/07/2023
CX complaint - has to push on micro door to get to operate - Adjusted door and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MHW6630HW3
Near Carbondale, CO 81623
James R
Job Details:
11/07/2023
Replaced bellow and cleaned door glass. Test run in a wash cycle to check for a leak. None.Customer signed waiver.Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Santa Fe, NM 87507
Jason
Job Details:
11/07/2023
installede parts unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ0
Near Santa Fe, NM 87507
Jason
Job Details:
11/07/2023
installed parts unit checks ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC700HPS
Near Santa Fe, NM 87501
Jason
Job Details:
11/07/2023
checked unit found cx issue is normal for this unit and nothing can be done to fix it. rh door sticks out a little more then lh
We serviced a
MAYTAG WASHER
Model MVWP576KW1
Near Rio Rancho, NM 87144
Larry
Job Details:
11/07/2023
Installed parts listed and Still not spining right - Called techline (SR7737741838) - Unit is unrepairable
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Rio Rancho, NM 87144
Larry
Job Details:
11/07/2023
Installed valve and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ15
Near Rio Rancho, NM 87144
Larry
Job Details:
11/07/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Rio Rancho, NM 87144
Larry
Job Details:
11/07/2023
Installed cap and tested good - Unit is good to go
We serviced a
MAYTAG DRYER - ELECTRIC
Model MED4500MW0
Near Albuquerque, NM 87105
Larry
Job Details:
11/07/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Santa Fe, NM 87501
Jason
Job Details:
11/07/2023
checked unit found loose hose tightened connection unit checks ok
We serviced a
KITCHENAID REFRIGERATOR
Model KUDR204EPA00
Near Santa Fe, NM 87501
Jason
Job Details:
11/07/2023
installed parts listed unit checks ok
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Fountain, CO 80817
Roman
Job Details:
11/07/2023
Tried turning the washer on but it would not turn on. Checked the wall for volts and it is not getting voltage. Could not find the breaker or get into the unit that has the breaker to flip and test washer. Landlord going to call an electrician to have the outlet looked at.
We serviced a
SAMSUNG RANGE - GAS
Model NX60BB871112AA 02
Near Pueblo West, CO 81007
Jeremy
Job Details:
11/07/2023
Installed ordered parts. Tested control. I asked Cx to complete the survey.
We serviced a
GE M/W OTR
Model JVM3160DF8BB
Near Edwards, CO 81632
Erik
Job Details:
11/07/2023
fan NOT positioned for recirculating vent *see quick picsINSTALL UNIT /TEST: GOODJOB COMPLETE
We serviced a
GE DRYER
Model GTD33EASK0WW
Near Eagle, CO 81631
Erik
Job Details:
11/07/2023
install/test: GOODJOB COMPLETE
We serviced a
GE DRYER
Model GFD14ESSN0WW
Near Eagle, CO 81631
Erik
Job Details:
11/07/2023
install heater/ test: GOODJOB COMPLETE
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Pueblo West, CO 81007
David
Job Details:
11/07/2023
Replaced diffuser Checked and is running good
We serviced a
FRIGIDAIRE DISHWASHER
Model LFBD2409LM0B
Near Colorado Springs, CO 80915
Ralph
Job Details:
11/07/2023
"upon arrival ran unit, unit drained and then started to fill, once the recirc pump kicked in you could hear the unit screaming, the recirc pump is bad and just spinning and not moving water, unit has a bad recirc pump, cust replacing unit...autho no. 9YHH43"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Divide, CO 80814
Mathew
Job Details:
11/07/2023
Replaced switch. Test op all okay.
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Divide, CO 80814
Mathew
Job Details:
11/07/2023
Vacant home. Found drain in floor backing up under washer. Machine tests fine.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Florissant, CO 80816
Mathew
Job Details:
11/07/2023
"Found bad cam assembly and belt. Replaced parts, test op all okay. Unit working as expected."
We serviced a
BLUESTAR COOKTOP
Model RGTNB488BV2PLT
Near Colorado Springs, CO 80906
Roman
Job Details:
11/07/2023
Adjusted the igniter and burner head. Showed cx how the igniter need to be in front of a hole.
We serviced a
WHIRLPOOL DRYER
Model WED8620HC2
Near Breckenridge, CO 80424
Antonio
Job Details:
11/07/2023
Found bad acu and wire harness Pt#w11685963$275.66andw11690849$174.1$149.95 CK Auth# MA9N43
We serviced a
JENN-AIR RANGE
Model JES9860CAS02
Near Breckenridge, CO 80424
Antonio
Job Details:
11/07/2023
Found bad infinite switch cx holding on repairs Pt# wp74011489 $125.16$169.95 CK Auth# 94L9U4
We serviced a
KITCHENAID ICE MACHINE
Model KUID308HPS01
Near Carbondale, CO 81623
James R
Job Details:
11/07/2023
Replaced tube asy and recirculation pump. Reassembled and test run unit. Ok But the drain is restricted does not drain as quickly as it should. Water backs up this can melt some of the ice or even frz. Need to have this drain issue resolved buy installer. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HDEDBSR/AA
Near Manitou Springs, CO 80829
Kris
Job Details:
11/06/2023
cx is deciding on repairs fc temp@2.0 rc temp@58.4 evap cover da97-12608a 274.80pcb da94-02679d 137.00
We serviced a
GE WASHER
Model GFW550SSN4WW
Near Colorado Springs, CO 80916
David
Job Details:
11/06/2023
"Checked washer Ran through cycles, one without clothes one with clothes. Ran normally without clothes, took a while for it to find its balance with clothes but not too long to give an error code.It did have an error code 26 water level drop.Said to check level sensor, tube, and drain. End of drain hose was down into the p-trap, repositioned"
We serviced a
THERMADOR FREEZER
Model T18ID80NLP/46
Near Colorado Springs, CO 80918
Jessie
Job Details:
11/06/2023
Replaced inverter and tested unit. Unit is functioning as designed
We serviced a
BOSCH DISHWASHER
Model SHP65T55UC/07
Near Colorado Springs, CO 80920
Jessie
Job Details:
11/06/2023
Replaced panel. Test op. All.ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED5PVEXWS14
Near Colorado Springs, CO 80920
Glenn
Job Details:
11/06/2023
"Tenants not onsite. Remotely let me in the house to complete repair. Install New Water Filter & Icemaker. Cycle Test IM , All OPS Test:OK , Locked front door on my way out."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Falcon, CO 80831
Aaron
Job Details:
11/06/2023
"Water line cracked flat the water inlet valve, replaced line, no incoming water line from wall to the inlet valve so unable to test. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA 01
Near Colorado Springs, CO 80925
Jeremy
Job Details:
11/06/2023
Cx was told by samsung that repair would be covered by them. I discussed service charge with CX and this issue came up. No work was completed by me.
We serviced a
GENERAL ELECTRIC DRYER - ELECTRIC
Model HTX24GASK1W
Near Colorado Springs, CO 80904
Roman
Job Details:
11/06/2023
"Turned the dryer on and it started right up and started to heat, let it run and it seems like its working fine. Sounds fine Told cx to call us back if they continue having issues."
We serviced a
WOLF RANGE
Model DF486G-3
Near Colorado Springs, CO 80906
Roman
Job Details:
11/06/2023
Installed new relay board for the right oven. Tested the ovens and both are heating up. Tested all the burners and flattop and they are all working great. Range working great. Paid labor $389.95 cc $389.95 CC Auth# FN4F43
We serviced a
SAMSUNG WASHER
Model WF42H5000AW/A2 11
Near Colorado Springs, CO 80903
Roman
Job Details:
11/06/2023
"Washer has some sitting water in it. Ran the washer in diagnostics and error codes up for not draining properly and not spinning Pulled the drain pump filter out and it was full of stuff put it back together and the washer is working great. Recommend to cx checking the filter every once and a while and making sure the door stays open, keeping the glass clean. Labor $129.95Sc $129.95Total cost $259.90 paid cc $259.90 CC Auth# 3F9FN9"
We serviced a
BOSCH RANGE
Model HGI8054UC/09
Near Pueblo, CO 81008
James
Job Details:
11/06/2023
"found unit needing bake igniter. unit is lifted 2 inches on platform will need 2 man. igniter 00755058 241.50+tax, sc 149.95, labor 249.95 x2, mps 14.50. total: 925.65. cust declines at this time. collected 149.95"
We serviced a
GE DISHWASHER
Model GDP645SYN2FS
Near Colorado Springs, CO 80919
Jessie
Job Details:
11/06/2023
Replaced control and tested unit job complete
We serviced a
WHIRLPOOL DRYER
Model WED5605MC
Near Colorado Springs, CO 80920
Glenn
Job Details:
11/06/2023
"Broken Blower Wheel , Had to cut blower off wheel. Install New Blower wheel. All OPS Test:OK"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Grand Junction, CO 81503
James R
Job Details:
11/06/2023
Found rotor bolt loose. Removed rotor. some of the wiring for clutch was loose got cut. Replaced clutch and also found Slider metal ring had slipped and was out of position so could not shift properly. Replaced slider. Reassembled rotor .Do a HLMS caliobration cycle and then put thru a diagnostics test. Checked ok operating as should. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, CO 80911
Roman
Job Details:
11/06/2023
Installed new control board and thermostats. Put the dryer back together and tested it and ran diagnostics. Dryer working great.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS06
Near Colorado Springs, CO 80921
Glenn
Job Details:
11/06/2023
Damper not closing. Install New Damper. All OPS Test:OK
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JS3
Near Colorado Springs, CO 80925
Carlos
Job Details:
11/06/2023
Installed burner and switch ran test op all ok
We serviced a
SAMSUNG DRYER
Model DVE53BB8700VA3
Near Colorado Springs, CO 80921
Mathew
Job Details:
11/06/2023
"Replaced thermistor, test op all okay."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Fountain, CO 80817
Carlos
Job Details:
11/06/2023
"Ran test op, Found broken wire in element. Replaced wire, runs ok"
We serviced a
MAYTAG OVEN
Model SVD48600B
Near Colorado Springs, CO 80926
Carlos
Job Details:
11/06/2023
Ran test op. Needs a control board. No power to bake element. Bad relay. Part is discontinued (71002594) Cx paid SC $129.95 CC Auth# YU4993
We serviced a
DACOR DISHWASHER
Model DDW24M999US/DA
Near Colorado Springs, CO 80924
Brandon
Job Details:
11/06/2023
Replaced parts and tested op all ok hass passed
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Monument, CO 80132
Glenn
Job Details:
11/06/2023
"Reset connections to PCB. Unable to find any leaks after running unit diag cycle 5X. However, did notice foam buildup inside after start of 3rd Diag Cycle. Techline: Suggest water temp issues, water temp only reaching 115F after several minutes at sink. Also possible Rinseaid overdose since using pods and also rinseaid in dispenser. turned dispenser down for now. Suggest customer run hot water at sink for several minutes until hot, use high temp wash setting option, and possibly switch to liquid detergent once pods are used up. Also suggest using dishwasher cleaner to clear out soap buildup. SR# 7737725652"
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Colorado Springs, CO 80905
Carlos
Job Details:
11/06/2023
"Installed gearcase, clutch, stator and motor. Ran test op runs ok"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Colorado Springs, CO 80910
Carlos
Job Details:
11/06/2023
"Ran test op. No issues found with heating components. Used air flow test kit, Cx has insufficient air flow in vents. Recommend cx clean vents."
We serviced a
WHIRLPOOL WASHER
Model NTW4516FW4
Near Colorado Springs, CO 80923
Aaron
Job Details:
11/06/2023
"Removed and replaced control, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ05
Near Colorado Springs, CO 80904
Carlos
Job Details:
11/06/2023
"Installed diffuser. ran test op, checked all fans and compressor, runs all."
We serviced a
GE M/W OTR
Model JVM3160DF8CC
Near Parachute, CO 81635
Erik
Job Details:
11/06/2023
flickering display - replce UI board asm WB56X38148Test: GOODJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, CO 80919
Mathew
Job Details:
11/06/2023
"Found cam assembly bolt loose, used loc tote and tightened. Found f0e8 error code, too much residual water. Ran a spin to clear tub. Ran diagnostics, all good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM09
Near Colorado Springs, CO 80904
Ralph
Job Details:
11/06/2023
installed parts and cust to monitor
We serviced a
SAMSUNG DRYER
Model DVE45B6300P/A3
Near Colorado Springs, CO 80924
Brandon
Job Details:
11/06/2023
"Found drum rubbing on side of frame, straightened frame and tested op all ok hass passed"
We serviced a
BOSCH MICROWAVE
Model HMC80251UC/01
Near Colorado Springs, CO 80908
Jessie
Job Details:
11/06/2023
Door is damaged right hand corner. Customer doesn't want a new door after I showed her there no difference. All functions are ok
We serviced a
SAMSUNG DRYER
Model DVE52A5500C/A3
Near Colorado Springs, CO 80908
Brandon
Job Details:
11/06/2023
"Error DC, found bad door switch, replaced door switch and tested op all ok hass passed"
We serviced a
WHIRLPOOL DISHWASHER
Model WDPA70SAMZ1
Near Grand Junction, CO 81507
James R
Job Details:
11/06/2023
Replaced control and vent asy. Put into service diagnostics test. Can hear water circulating properly now. Amp draw of motor .680 good. Sprayer arms are turning. Heat cycle is working. 7.3 amps.good .Customer should be sure to run water at sink to be sure it is hot at start of cycle. Use rinse agent this aids in drying and helps prevent spots. Use hi temp wash and sani- rinse during cycles to get water very hot. Helps with drying and removing stubborn items on dishes. Best to remove large food items off dishes can plug filter and screen and remain in unit. Then periodically clean unit with a dishwasher cleaner to throughly clean unit. Customer signed waivers.Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MONOGRAM REFRIGERATOR
Model ZIW303NPPBII
Near Colorado Springs, CO 80904
Ralph
Job Details:
11/06/2023
"Replaced parts and cycled and filled the unit, cust to moitor"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF518SAHM
Near Vail, CO 81657
Antonio
Job Details:
11/06/2023
Found disconnected drain pump reconnected unit tested good
We serviced a
KITCHENAID REFRIGERATOR
Model KFIS20XVMS2
Near Albuquerque, NM 87108
Jason
Job Details:
11/06/2023
installed rails unit checks ok
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Albuquerque, NM 87114
Larry
Job Details:
11/06/2023
Installed clutch and slider and tested good - Unit is good to go
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MB0
Near Albuquerque, NM 87110
Jason
Job Details:
11/06/2023
installed ignitor unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ03
Near Rio Rancho, NM 87144
Larry
Job Details:
11/06/2023
CX complaint - Making low pitch noise - Inspected unit and found I could not reproduce the issue - Unit is operating as designed
We serviced a
WHIRLPOOL FREEZER
Model WZF56R16DW04
Near Albuquerque, NM 87109
Jason
Job Details:
11/06/2023
"checked unit found start device is badSC$151,85MISC$17.50LABOR$195.25START DEVICE#W11092533$113.58TX$9.65TOTAL$487.83CX DOES NOT WANT TO REPAIRAuth code:3M3T4V$151.85"
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Albuquerque, NM 87111
Jason
Job Details:
11/06/2023
installed gearcase and basket unit checks ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Edgewood, NM 87015
Jason
Job Details:
11/06/2023
installed gaskets unit checks ok
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Pueblo, CO 81005
James
Job Details:
11/06/2023
found ptrap leaking when unit draining. all machine ops test good. advised cust to have licensed plumber out to address. collected 129.95
We serviced a
SAMSUNG WASHER
Model WF50A8600AV/US
Near Colorado Springs, CO 80903
Mathew
Job Details:
11/06/2023
Replaced valves. Test op all okay.
We serviced a
KENMORE WASHER
Model 11022532511
Near Pueblo, CO 81004
James
Job Details:
11/06/2023
found loose wire at the water valve causing no water secured and tested all ops test good.
We serviced a
SAMSUNG WASHER
Model WA40A3005AW/A4
Near Colorado Springs, CO 80916
Mathew
Job Details:
11/06/2023
"Replaced entire wire harness. Test op, unit working as expected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Monument, CO 80132
Glenn
Job Details:
11/06/2023
"Water leaking from cracked water line that connects to supply valve. Customer was sent replacement water line - P/N: W11482381 , Installed new water line, all OPS Test:OK, No Leaks."
We serviced a
BOSCH REFRIGERATOR
Model B36FD50SNB/02
Near Pueblo, CO 81004
Kris
Job Details:
11/06/2023
installed dryer and magnet valve charged with 2oz fo r600 ran test op all ok at this time cx will monitor unit.
We serviced a
GE REFRIGERATOR/TOP
Model GWE19JGLWFWW
Near Pueblo West, CO 81007
James
Job Details:
11/06/2023
Found loose wire at evaporator fan rubbing on fan blade causing noise interminently secured wire and tested all operations check OK no more noise present
We serviced a
BOSCH DRYER
Model WTW87NH1UC/01
Near Aspen, CO 81611
Erik
Job Details:
11/06/2023
dryer plumbing NOT correct for installed drain - following user/owner/install instructions install drain and test: GOODJOB COMPLETE
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFG02
Near Edwards, CO 81632
Antonio
Job Details:
11/06/2023
Found frezzer door sagging adjusted aslo in formed home owner fridge is not going to work properly in a none headed garage
We serviced a
JENN-AIR REFRIGERATOR
Model JUCFP242HX11
Near Wolcott, CO 81655
Antonio
Job Details:
11/06/2023
Installed new acu and icemaker unit tested good
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Gypsum, CO 81637
Antonio
Job Details:
11/06/2023
Installed new acu unit tested goodLb $189.95Tp$17.50 $207.45 CC Auth# EXFNK3