We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5001SR/AA
Near Colorado Springs, CO 80924
Brandon
Job Details:
07/29/2024
"Unit not powering on, checked outlet for power 120 volts, check power at PCB 120 volts found power connector on PCB loose reseated connection, unit powered on and started cooling, no errors, tested on all checks ok hass oqc passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF26CG7400SRAA
Near Colorado Springs, CO 80924
Brandon
Job Details:
07/29/2024
"No errors no cool all rooms, found leak at right side lokring, repaired leak and replaced filter drier, installed process stub and vacuumed unit for 10 minutes charged unit to spec 86g hass oqc passed"
We serviced a
U-LINE REFRIGERATOR
Model U/30217578/00
Near Colorado Springs, CO 80904
Eric
Job Details:
07/29/2024
"Customer complaint that fridge was making loud clacking sound. Arrived at location and found that customer had unplugged unit and it has thawed out for two days, no longer making sound, as customer continued to describe location of the sound it is evident that its the bi-metal failing and not allowing the unit to go into defrost. Recommend replacing if noise comes back. Collected HC $149.95$149.95 CK Auth# F3V9VW"
We serviced a
MAYTAG WASHER
Model MVWC415EW1
Near Colorado Springs, CO 80919
Glenn
Job Details:
07/29/2024
"Customer indicates they used 'Soak' cycle and it never drained. I explained that the soak cycle does not spin, but it should drain most of the water, may me some water left over from water held in clothes, since no spin involved. No Error codes, Calibrated Unit > Pass, Diag Test > Pass, Visual Inspection of under carriage> Pass, Capacitor OK, All OPS Test:OK at this time. Paid SC Fee Via Chk# 11211, Autho#49CH3K"
We serviced a
WHIRLPOOL WASHER FRONT LOA
Model WFW5605MW0
Near Colorado Springs, CO 80920
Glenn
Job Details:
07/29/2024
"Stacked Unit and customer already pulled stack out and removed drain hose and back panel. F5E2 - Lock Failure , F8E1 - Long Fill , Not draining properly, Bad Drain pump - W11458345 $195.62 , Tax $16.04 , MPS $14.50 , SC $129.95 , Labor $189.95 , Helper $189.95 ( to unstack dryer from Washer & Re-install once completed.) Declined Estimate for now, Paid SC Fee $129.95 , Autho# 3W9L94"
We serviced a
MIELE COFFEE MACHINE
Model CVA4066
Near Colorado Springs, CO 80919
Ralph
Job Details:
07/29/2024
"called tech support for the issue cust is experiencing, we reset descale the milk piping and the brew unit, as well i made certain that the tray was not leaking and cleaned out nay further debris i found behing the tray, alson sanded the connectors on the tray to get a better reading, tech support suggest if the issue appears again that we should replace the sensors in the back of the unit, onlly charging seervice fee today...autho no.k449v9"
We serviced a
SUB ZERO REFRIGERATOR
Model IW-18A-RH
Near Colorado Springs, CO 80919
Ralph
Job Details:
07/29/2024
"believe issue was due to door not closing all the way, one slide was not cclosing all the way and interferring with the door, remediedthe issue and cust to monitor"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS02
Near Colorado Springs, CO 80922
Carlos
Job Details:
07/29/2024
Installed water valve ran test runs ok cx will observe $229.95 CC Auth# P3A4F9
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS20
Near Rio Rancho, NM 87124
Joe
Job Details:
07/29/2024
Cx complaint. Unit keeps restarting. Replaced control and ui ordered last visit. Tested unit. Unit good to go
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Rio Rancho, NM 87124
Joe
Job Details:
07/29/2024
Cx complaint. Dryer not heating. Inspected unit. Replaced element and cut off. Tested unit. Unit good to go
We serviced a
WHIRLPOOL M/W OTR
Model WMH73521CE0
Near Albuquerque, NM 87120
Larry
Job Details:
07/29/2024
Installed door and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW0
Near Grand Junction, CO 81507
James R
Job Details:
07/29/2024
Customer signed disclaimer. Replaced ACU and bellow. Hooked up and test run thru service diagnostics. Test good no issues. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
AMANA REFRIGERATOR
Model ASI2175GRS08
Near Albuquerque, NM 87114
Larry
Job Details:
07/29/2024
CX stats he has an extended warranty - Explained that he needs to contact his warranty company and have them dispatch accordingly
We serviced a
WHIRLPOOL WALLOVEN
Model WOS51EC0HS20
Near Rio Rancho, NM 87144
Joe
Job Details:
07/29/2024
Cx complaint. F8E4 error. Replaced control and blower ordered last visit. Tested unit. Unit good to go
We serviced a
WHIRLPOOL OVEN
Model WOS52ES4MZ
Near Albuquerque, NM 87114
Joe
Job Details:
07/29/2024
Cx complaint. Oven wont lock to do self clean. Replaced control ordered last visit. Tested unit. No errors and door is locking. Unit good to go
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Grand Junction, CO 81501
James R
Job Details:
07/29/2024
Customer signed disclaimer. Replaced Elec. control. Test unit did a DLMS calibration then a service test. Unit operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG DRYER
Model MEDP586KW0
Near Albuquerque, NM 87108
Jason
Job Details:
07/29/2024
Installed parts unit checks ok
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Albuquerque, NM 87108
Jason
Job Details:
07/29/2024
Installed part unit checks ok
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Albuquerque, NM 87108
Jason
Job Details:
07/29/2024
Installed motor unit checks ok
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Albuquerque, NM 87110
Larry
Job Details:
07/29/2024
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ4
Near Rio Rancho, NM 87144
Joe
Job Details:
07/29/2024
Cx complaint. Insulation coming out side. Inspected unit. Found Insulation not put in correct. Pulled unit and fixed Insulation. Tested unit. Unit good to go
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, NM 87108
Jason
Job Details:
07/29/2024
nstalled parts listed unit checks ok
We serviced a
MAYTAG WASHER
Model MVWB765FW0
Near Colorado Springs, CO 80911
Carlos
Job Details:
07/29/2024
Installed door ran test runs ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Colorado Springs, CO 80924
Aaron
Job Details:
07/29/2024
"Removed and replaced evaporator fan motor, tested unit, working well, fan has good push. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW1
Near Colorado Springs, CO 80922
Aaron
Job Details:
07/29/2024
"Drain pump and control are shorted out, removed and replaced components, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF991BOOM01
Near Colorado Springs, CO 80903
Carlos
Job Details:
07/29/2024
Cleaned evaporator. Cx will observe.
We serviced a
JENNAIR REFRIGERATOR
Model JFX2897DRM02
Near Colorado Springs, CO 80919
Glenn
Job Details:
07/29/2024
"Install & Adjust New Gaskets, All OPS Test:OK"
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Colorado Springs, CO 80924
Aaron
Job Details:
07/29/2024
"Removed and replaced basket and washplate, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Grand Junction, CO 81507
James R
Job Details:
07/29/2024
Customer signed disclaimer. Put into service diagnostics test 56 error code E5 indicates a icemaker thermistor is bad. Test 45 no water came into icemaker. Replaced valve and then icemaker. Sealed icemaker housing with tape to prevent air leak. Cut pwr to unit then reapplied pwr. Checked icemaker operation test. 57 no issues. Then checked for water fill to icemaker. Test 45 filled good. Operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Edwards, CO 81632
Antonio
Job Details:
07/29/2024
Installed compressor and couplers unit tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Grand Junction, CO 81507
James R
Job Details:
07/29/2024
Customer signed disclaimer. Evap iced over again completely. Put into service test. Test 5 shows that it is reading the evap thermistor. Defrost cycle heater is drawing 1.0 amps. So is heating. Checked evap thermistor two pink wire at sontrol 19.9 k ohm. Iced completely over. Thawed out evap and replaced thermistor. Put zip ties and silver tape around thermistor. Took pics. Reassembled unit. Put into service diagnostics test 5 still shows is reading thermistor.Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF540CWHZ11
Near Monument, CO 80132
Glenn
Job Details:
07/29/2024
"Icemaker was spraying water during harvest, So they turned IM Off, Checked Icemaker, Fill Tube & Funnel clear. Cycle Test > Pass, Fill Test > Pass, Possible issue was due to frost buildup from door not sealing properly? Frzr door not closing smoothly and keeping it from closing 100%, causing frost buildiup on rails. No Frost / Ice buildup on Evap cover, Defrost rails to allow door to close smoothly. Adjusted front legs to allow better pitch for doors to stay closed. Slight vibration noise from Evap Fan, But not abnormal. If problem returns or gets worse, suggest replace Evap Motor - W11024089 & Fan Blade - WP2169142 , All OPS Test:OK at this time."
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Colorado Springs, CO 80924
Aaron
Job Details:
07/29/2024
"Element support broken, replaced support, unit is working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Pueblo West, CO 81007
David
Job Details:
07/29/2024
"Replaced control, ran cycle and ran as expected."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Pueblo West, CO 81007
David
Job Details:
07/29/2024
"Replaced suspension rods, whirlpool is replacing machine per cx."
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Pueblo West, CO 81007
David
Job Details:
07/29/2024
"Called tech line, sr# 7739594010, had me check thermistors, readings show they are good, good air flow. He said screen is showing check vent as a reminder."
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Colorado Springs, CO 80923
Aaron
Job Details:
07/29/2024
"Washer suspension rod slightly bent, removed and replaced suspension assembly. Tested unit, working as designed, tapping sound is the drainline moving against back wall, put in best position, advised customer of usage and survey."
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ5
Near Bend, OR 97701
Levi
Job Details:
07/29/2024
"Replaced ignition module and broil ignitor, tested good"
We serviced a
ZEPHYR RANGE HOOD
Model AK7636BS
Near Colorado Springs, CO 80924
Roman
Job Details:
07/29/2024
Installed control board and ui panel. Tested the u l it and its working great. No error codes.
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Colorado Springs, CO 80909
Carlos
Job Details:
07/26/2024
Installed water valve ran test runs ok cx will observe
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9070SR/AA
Near Colorado Springs, CO 80919
Brandon
Job Details:
07/26/2024
"No errors, ice buildup blocking airflow, removed all ice and cycled ice maker all checks ok"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Pueblo, CO 81001
David
Job Details:
07/26/2024
"Replaced suspension rods and drain pump, ran diagnostic cycle and a short cycle. Running as expected."
We serviced a
FRIGIDAIRE OTR MICROWAVE
Model FGMV176NTF
Near Fountain, CO 80817
Jerimiah
Job Details:
07/26/2024
"No answer at door, took pig, tagged, contacted office to contact Cust to reschedule, closing call."
We serviced a
FRIGIDAIRE OTR MICROWAVE
Model FGMV176NTF
Near Fountain, CO 80817
Jerimiah
Job Details:
07/26/2024
"No answer at door, took pig, tagged, contacted office to contact Cust to reschedule, closing call."
We serviced a
WHIRLPOOL DRYER
Model LTE5243DT3
Near Albuquerque, NM 87106
Jason
Job Details:
07/26/2024
Checked unit found timer and wiring has caught fire at some point PARTS LISTED ARE NOTICIBLY DAMAGED THERE MAY BE ADITIONAL PARTS NEEDED ONCE THESE PARTS ARE REPLACED!MPS $18.99LABOR$271.20TIMER#WP3952499$304.92HARNESS#WP3406288$159.02TEMP SWITCH#WP8054142$106.54PRESSURE SWITCH#WP3362987$168.10BELT#3394652$76.72KIT#4392065$72.55TX$75.47TOTAL$1253.51CX HAS TO THINK OVER REPAIR
We serviced a
BOSCH DISHWASHER
Model DWHD760CFP/22
Near Colorado Springs, CO 80908
Eric
Job Details:
07/26/2024
"Customer complaint that dishes were not coming out dry enough. Cleaned filter trap and Inspected unit, tested found no errors upon further inspection, Realize that unit did not have rinse aid, educated customer on proper use of dishwasher and proper maintenance."
We serviced a
GE REFRIGERATOR BOT
Model GFE28GYNJFS
Near Pueblo, CO 81003
David
Job Details:
07/26/2024
"Checked refrigerator, making ice and cooling when got here, put into diagnostics checked components, checked good. Cx will keep an eye on it."
We serviced a
SAMSUNG RANGE GAS
Model NX58H5600SS/AA
Near Colorado Springs, CO 80916
Jerimiah
Job Details:
07/26/2024
"Bake igniter weak, needs replacing, labor will be $219.95 upon return service. Part number provided by Samsung part research. Cust is going to look for new unit. Charging service call $149.44 CC Auth# 9YKNFHDG94-00520A bake igniter $271.58"
We serviced a
KITCHENAID REFRIGERATOR BOT
Model KRFC704FBS01
Near Parachute, CO 81635
James R
Job Details:
07/26/2024
Customer signed disclaimer. Put into service diagnosfics test 120. Went thru fine says PA at end working as should. Checked ice box and icemaker thermistors checked good. Cycled icemaker water fill did as should. Also checked icemaker fan working good. Please fill out whirlpool tech satisfaction survey. Thank You. Customer paid labor $189.95 auth code. PKX9C4
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5201SG/AA
Near Redmond, OR 97756
Levi
Job Details:
07/26/2024
"Replaced compressor and filter dryer, tested all good. Unit is starting to cool already. Ran hass and it past"
We serviced a
SAMSUNG REFRIGERATOR BOT
Model RF22K9581SGI
Near Colorado Springs, CO 80918
Brandon
Job Details:
07/26/2024
"Error 41 c, communication error between main PCB and family hub, call tech support unable to put unit into Force mode due to 41c error, error will need to be resolved before diagnosing no cool issue, harness from table top to PCB continuity checks ok, need to replace main PCB and family hub, Svf paid $129.95 Auth# 9UTFJ4, Da94-03040a, Da97-16622a, Parts $1199.55, Labor $209.95, Svf $129.95, Mps $14.50, Tax $98.36"
We serviced a
KITCHENAID ICEMAKER
Model KUIC18PNTS1
Near Colorado Springs, CO 80920
Glenn
Job Details:
07/26/2024
"Install New Main PCB again, as 1st one stopped working after 2-4 hours? Techline: Same SR#, Passed all Diag Tests. Did not need to attempt installing another Pump. Allow 72 Hours for ice production."
We serviced a
GE REFRIGERATOR
Model PYE22KBLITS
Near Colorado Springs, CO 80908
Eric
Job Details:
07/26/2024
"Replaced failed parts and set temps to recommend settings, both freezer and fridge coming down in temp and customer will monitor."
We serviced a
SAMSUNG RANGE
Model NE59T4321SW/AA
Near Colorado Springs, CO 80923
Jerimiah
Job Details:
07/26/2024
"Unit was in bake mode at 350 when experienced runaway temp causing door to look. Did temp check. Set 350 preheated to 355, rose to 364 and avgd 343. Unit never got to extreme temps as was observed by Cust. She said that when problem occurred she unplugged unit and allowed it to cool down and continued to function properly, s/w glitch? Cust will keep track of any further issues, if so please order part below. Labor will be $219.95. Charging service call $129.95 CC Auth# R9P3R4DE94-03926B control board $266.40"
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS1
Near Bosque Farms, NM 87068
Larry
Job Details:
07/26/2024
CX complaint - Not heating and some buttons don't work - Inspected unit and fojnd the control not sending power to the element and the UI malfunctioning - Unis needs control and UI - CX does't wand to bear the cost of repair and will replace - Estimate in QP - Collected SC
We serviced a
INSINKERATOR GARBAGE DISPOSAL
Model 79850K-ISE
Near Colorado Springs, CO 80921
Eric
Job Details:
07/26/2024
Replaced disposal and tested. Unit working properly no leaks.
We serviced a
JENNAIR RANGE
Model JIS1450DS1
Near Colorado Springs, CO 80917
Glenn
Job Details:
07/26/2024
"Unit started smoking from back of unit after cooking a pizza. Found Induction harness had melted and caught fire inside protective heat shielding. Techline: SR# 7739579964 , Documented and submitted pics, suggest replace induction module which comes w/ harness. Safety - 866-550-5136 , SR# 7739552324 , Offering to make a prorated exchange. , Otherwise I provided an estimate for the repair. Module - W10886867 $506.11 , Tax $41.50 , MPS $14.50 , Labor $269.95 , SC (Paid by Manuf) Declined Estimate for now."
We serviced a
GE WALL OVEN ELECTR
Model JT3800DH6BB
Near Colorado Springs, CO 80908
Roman
Job Details:
07/26/2024
"Pulled unit out and the power cord has been modified to fit inside the unit. Had to disassemble the power cord and unit. Checked heating elements and and they are okay, bad high limit. Recommend replacing it. High limit thermostat #WB24X46906 $186.52Tax $15.29Parts total $201.81Labor $249.95MPs $14.50Sc $129.95Total cost $596.21Paid $596.21 CC Auth# PRPUM4"
We serviced a
ASKO DISHWASHER
Model D5656
Near Colorado Springs, CO 80908
Roman
Job Details:
07/26/2024
"Installed top panel and ui board protector, re installed dw and tightened down the upper spray arm. Put all the rack adjusters back in place. Tested the unit. Dw working great. Paid sc + labor $$359.95 CC Auth# EE9944"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS02
Near Colorado Springs, CO 80921
Eric
Job Details:
07/26/2024
Replaced failed part and unit running properly at this time.
We serviced a
GE WASHER STACK LAU
Model GFW148SSM1WW
Near Colorado Springs, CO 80907
Eric
Job Details:
07/26/2024
Replaced gasket and tested. Unit has no leaks.
We serviced a
MAYTAG DRYER
Model MED3500FW0
Near Albuquerque, NM 87114
Joe
Job Details:
07/26/2024
Cx complaint. Dryer not heating. Replaced element ordered last visit. Tested unit. Unit good to go
We serviced a
SAMSUNG WASHER
Model WF45A6400AW/USE
Near Colorado Springs, CO 80904
Mathew
Job Details:
07/26/2024
Replaced all inner tub parts. Could not test unit as it is in a garage. All okay. Cx not home at time of repair. Left messages and sent bill via IWallet.
We serviced a
SAMSUNG WASHER
Model WF45T6000AW/A5
Near Colorado Springs, CO 80911
Mathew
Job Details:
07/26/2024
Replaced faulty door. Test op all okay. Will return damaged door Monday.
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Fountain, CO 80817
Mathew
Job Details:
07/26/2024
Replaced faulty pump and hose section. Test op
We serviced a
SAMSUNG RANGE
Model NX60A6311SS/AA
Near Colorado Springs, CO 80925
Mathew
Job Details:
07/26/2024
Found bad pressure from regulator. Replaced regulator and test op. All okay.
We serviced a
SAMSUNG DISHWASHER
Model DW80B7070UG/AA
Near Colorado Springs, CO 80921
Brandon
Job Details:
07/26/2024
"Replaced wax motor, and door switch and tested on all checks ok"
We serviced a
SAMSUNG DRYER
Model DVE41A3000W/A3
Near Colorado Springs, CO 80916
Mathew
Job Details:
07/26/2024
Found motor off of mounts. Replaced motor assy. Test op all okay.
We serviced a
SAMSUNG WASHER
Model WA55A7300AE/US
Near Colorado Springs, CO 80924
Brandon
Job Details:
07/26/2024
"Drain pump failed, replaced drain pump and tested op all checks ok hass oqc passed"
We serviced a
SAMSUNG WASHER
Model WF50BG8300AVUS
Near Colorado Springs, CO 80925
Mathew
Job Details:
07/26/2024
"Inspected all water connections. Tightened leaking water supply line. Test op three times, no leaking found at the moment. Only water trail found was from back of machine, documented in quick pics. Unit working as expected."
We serviced a
WOLF WALL OVEN
Model DO30PM/S/PH
Near Colorado Springs, CO 80908
Roman
Job Details:
07/26/2024
"Installed the control board, tested the unit and its working great. Fan kit never arrived but does not need it. Also cx received a door not for this unit, not a fan kit."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Albuquerque, NM 87121
Larry
Job Details:
07/26/2024
Installed compressor and getting good heat exchange - Did not receive inverter - Unit should be good to go
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW
Near Rio Rancho, NM 87144
Joe
Job Details:
07/26/2024
"Cx complaint. Ui unresponsive. Inspected unit, reset unit. Secured drain hose. Tested unit. Unit good to go"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Albuquerque, NM 87110
Jason
Job Details:
07/26/2024
Installed parts listed. new UI wouldnt code with model and serial. since touchpad portion was the issue installed old ui control onto new touch pad unit checks ok
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Fruita, CO 81521
James R
Job Details:
07/26/2024
Customer signed disclaimer. Left roller support was not turning. Installed a repair kit. Reassembled and run unit it is operating as should. Please fill oiut whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ18
Near Albuquerque, NM 87114
Joe
Job Details:
07/26/2024
Cx complaint. Refrigerator turning on and off. Replaced control ordered last visit. Tested unit. Unit good to go
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Albuquerque, NM 87120
Larry
Job Details:
07/26/2024
Installed repair kit and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Los Lunas, NM 87031
Larry
Job Details:
07/26/2024
Installed sump and tested good - Unti is good to go
We serviced a
EDGESTAR WINE COOLER
Model CWR1661SZ
Near Colorado Springs, CO 80919
Ralph
Job Details:
07/26/2024
replaced parts and unti checked okay
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Colorado Springs, CO 80951
Carlos
Job Details:
07/26/2024
"Called Techline 7739580201, installed element and cutoff, techline recommend cx use boosters or inside vent kit. Household vent is way too long."
We serviced a
MAYTAG DRYER
Model MEDB835DW4
Near Colorado Springs, CO 80920
Glenn
Job Details:
07/26/2024
"Check & tighten Idler pulley, Blower wheel & rollers, All OPS Test OK at this time, unable to duplicate any noises. Possibly something made its way out of a pocket to drum felt and eventually worked its way out. All OPS Test:OK"
We serviced a
MAYTAG WASHER
Model MVWB835DW4
Near Colorado Springs, CO 80920
Glenn
Job Details:
07/26/2024
"Found motor bold loose. Tighten bolt, all OPS Test : OK, If problem returns replace Splutch assy & Mag Wheel w/ Bolt."
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ1
Near Colorado Springs, CO 80923
Jerimiah
Job Details:
07/26/2024
"Unit had a dead short across power, disconnected DSI board and short disappeared. Replaced DSI board, unit check ok. Disclosed survey to cust fcc 5starW10860916 DSI board"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF991BOOM01
Near Colorado Springs, CO 80903
Carlos
Job Details:
07/26/2024
"installed compressor, charged with R134a pressures low side 3psi high side 120 at start up. No leaks found , checked with gas detector. Cx will observe"
We serviced a
JENN-AIR RANGE
Model JES1750FS1
Near Colorado Springs, CO 80920
Glenn
Job Details:
07/26/2024
"Install New Main Control, Now only getting power from ground to each side of back element. Techline: Found broken wire going to element. Fixed broken wire, All OPS Test:OK"
We serviced a
MAYTAG DRYER
Model MGD6230HW3
Near Grand Junction, CO 81506
James R
Job Details:
07/26/2024
Tore apart and replaced blower but had to cut it off then the nut that holds it on. Reassembled and test run operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL M/W OTR
Model YWMH78519LZ00
Near Grand Junction, CO 81505
James R
Job Details:
07/26/2024
Signed disclaimer. Tore unit apart. Checked all elec connections. Did find blk wire to fuse loose tightened. Put a cup of water in to check all functions are working. Tested MW several times no issues. unit is working as should.
We serviced a
WHIRLPOOL WASHER/DRYER COM
Model WETLV27HW3
Near Colorado Springs, CO 80908
Aaron
Job Details:
07/26/2024
"Washer F2E1 stuck key error code upon arrival, inspected unit and secured connection to control, unit is working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ11
Near Colorado Springs, CO 80920
Eric
Job Details:
07/26/2024
"Changed out failing evap fan, unit running properly at this time. Customer will monitor."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Cañon City, CO 81212
James
Job Details:
07/26/2024
Found unit with f4e3 code. Replace pre-ordered part. Tested ops all ckok. Left litmus
We serviced a
KITCHENAID DISHWASHER
Model KDTM704LPA1
Near Cañon City, CO 81212
James
Job Details:
07/26/2024
Installed ordered part. Could not test unit. It is not installed
We serviced a
KITCHENAID RANGE
Model KSEG700ESS7
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
07/26/2024
Installed all replacement parts. Cust will keep of unit functionality. Unit check ok
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Florence, CO 81226
James
Job Details:
07/26/2024
#NAME?
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, CO 80923
Aaron
Job Details:
07/26/2024
"Thermostat shorted out, removed and replaced, improper power to the unit, recommend electrician to correct. Advised customer of situation and survey."
We serviced a
WHIRLPOOL RANGE
Model KFGG500ESS7
Near Cañon City, CO 81212
James
Job Details:
07/26/2024
Installed ordered part. Tested ops. All ckok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Grand Junction, CO 81504
James R
Job Details:
07/26/2024
Signed disclaimer.Took pic of closing date. Unit uneven put a shim at R.R. corner raised it up. 4387828A Now doesnt shift. Adjusted leveling screw on F.F. door to lower it down so even. Also put wood shims in front of the front rollers so it doesnt roll out each time the doors are opened. Checked door seals Frz and F.F. they are sealing good. Even though btm of F.F. door is out abit. Does not affect the operation of the unit. Please fill out whirlpool tech satisfaction survey. Thank You.; used 1 4387828A (Shim) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FMDM10
Near Colorado Springs, CO 80915
Carlos
Job Details:
07/26/2024
Unclogged fill tube. Placed permagum around fill tube to seal air leak
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FMDM10
Near Colorado Springs, CO 80915
Carlos
Job Details:
07/26/2024
Installed door all ok.
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Colorado Springs, CO 80922
Aaron
Job Details:
07/26/2024
"Removed and replaced components, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Redmond, OR 97756
Levi
Job Details:
07/26/2024
"Replaced control board and touchpad. Tested, all checks okay"