We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5300SRAA
Near Fountain, Colorado 80817
Mathew
Job Details:
10/08/2025
"Found rails sticking, cross bar out of place. Replace rails and cross bar. Test op all okay. Noises coming from rails are normal."
We serviced a
SAMSUNG REFRIGERATOR
Model RF23DB990012AA
Near Fountain, Colorado 80817
Mathew
Job Details:
10/08/2025
Found bad filter case assy. Replace filter case. Test op. All okay.
We serviced a
SAMSUNG WASHER
Model WF45B6300AW/US
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
10/08/2025
"Replaced motor and rotor, tested operation all checks ok hass passed"
We serviced a
MAYTAG DRYER
Model MED6630HC2
Near Rifle, Colorado 81650
James R
Job Details:
10/08/2025
Printed labels took pics ready to send.
We serviced a
WHIRLPOOL WASHER
Model MVWB965HW0
Near Colorado Springs, Colorado 80920
David
Job Details:
10/08/2025
"Installed ordered parts, ran calibration and diagnostic cycles. Running normal."
We serviced a
LG WASHER
Model WM1388HW
Near Colorado Springs, Colorado 80917
David
Job Details:
10/08/2025
"Checked washer, cold water not coming in. No cold water at wall box. He looking at getting a plumber."
We serviced a
LG DRYER
Model DLEX4200B.ABLEEUS
Near Colorado Springs, Colorado 80918
Brandon
Job Details:
10/08/2025
Replaced heater assy and tested operation all checks ok
We serviced a
LG WASHING MACHINE
Model WM3470CM.ABMEVUS
Near Avon, Colorado 81620
Antonio
Job Details:
10/08/2025
Installed new door assembly then ran a cycle for proper operation and unit tested good
We serviced a
LG REFRIGERATOR
Model LHTNS2403S.ASTCNA0
Near Avon, Colorado 81620
Antonio
Job Details:
10/08/2025
Leveled fridge doors for cx and ukit is Leveled
We serviced a
SAMSUNG MICROWAVE OVEN
Model NQ70CG700DSRAA
Near Colorado Springs, Colorado 80903
Mathew
Job Details:
10/08/2025
"Replaced bad magnatron. Unit passes first test, fails on third. Call tech line to troubleshoot. Agent recommends microwave control board if issues persist. Collect labor 189.95 $189.95 CC Auth# T9FN9YPart 277.24Tax $22.73Labor 229.95"
We serviced a
SUB ZERO WINE COOLER
Model IW30CI
Near Prineville, Oregon 97754
Richard
Job Details:
10/08/2025
Installed new switching valve charged unit to 6.5 ounces of Freon cycle tested unit all tested good at this time job complete
We serviced a
GE WASHER/DRYER COM
Model PFQ83HSLW0WW
Near Rifle, Colorado 81650
Clint
Job Details:
10/08/2025
"Customer signed disclaimer, had water valve we ordered . Cleaned filter housing out it was clogged with lint.Installed water valve .put unit back together and ran a cycle to check for leaks.Everything ran satisfactory. PLEASE TAKE TECH SURVEY,THANKS/Clint/Sean."
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Aspen, Colorado 81611
Clint
Job Details:
10/08/2025
"Customer signed disclaimer, stated that the lid lock isn't working like it should.Ran diagnostic test and 22 error came up =out of balance load. Noticed the cabinet of the lid was bent and causing lid lock not to make complete contact. Legs needed leveling also.Bent frame back into place and door locked like it should.PLEASE TAKE TECH SURVEY! THANK YOU. Clint/Sean noted,upper left corner was dented also."
We serviced a
PROFILE MICROWAVE OVEN
Model PVM9179SR1SS
Near Avon, Colorado 81620
Erik
Job Details:
10/08/2025
ACCESS WITHDOOR CODEINSTALL ALL COMPONENTS FOR HV TEST: PASS - BOIL 1 CUP OF WATER IN 60 SECJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model DSE26JMECCES
Near Pueblo, Colorado 81008
Domingo
Job Details:
10/08/2025
The machine is making ice it took longer but right now just told customer that if its stops it might need an ice maker
We serviced a
FRIGIDAIRE RANGE
Model FCRG3062ASB
Near Hillsboro, Oregon 97123
Nathan
Job Details:
10/08/2025
We sent a ignitor for the broil element complaint..Unit has a electric broil element Gas bake element and gas cooktop Broil element is heating and working properly Unit is only 110v so that explains the slow heating times. Spoke to tech line to confirm my thinking and they did They stated use and care manual states broil is not for cooking but only for browning purposes
We serviced a
SUBZERO REFRIGERATOR
Model BI-42
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
10/08/2025
CLEANED COND AND UNIT CHEKCED OKAY...AUTHO NO. R99L9A
We serviced a
BOSCH DISHWASHER
Model SHPM88Z75N/22
Near Colorado Springs, Colorado 80924
Scott
Job Details:
10/08/2025
installed listed parts checked op ok found no leak after install put strips down customer will watch
We serviced a
SUBZERO ICE MACHINE
Model UC-15IP
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
10/08/2025
INSTALLED PART AND UNIT CHECKED OKAY
We serviced a
SUBZERO REFRIGERATOR
Model 550
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
10/08/2025
"UNIT HAS A FAULTY COLD CONTROPL, WILL NEED LISTED PART...AUTHO NO, 9AA39N"
We serviced a
WHIRLPOOL WASHER
Model LAT9806AAE
Near Basalt, Colorado 81621
Clint
Job Details:
10/08/2025
"Customer signed disclaimer, stated the washer wasnt draining. Unit had half a tub full of water.Legs were to low in the front so we adjusted unit level. . We inspected and found the drain line was clogged with debris at the drain hole.Ran unit filled and drained perfectly. PLEASE TAKE TECH SURVEY.THANKS/Clint /Sean.Charged 229.95 card auth # 3WUV49"
We serviced a
BOSCH DISHWASHER
Model SHP65CM5N/25
Near White City, Oregon 97503
Jeff
Job Details:
10/08/2025
Explained possible odors from being on a well water. Also looked up white city water quality for odors and Explained. Machine is running as should ran diagnostic and no errors.
We serviced a
BOSCH DISHWASHER
Model SHE53C85N/01
Near Florissant, Colorado 80816
Charles
Job Details:
10/08/2025
"Replaced power module, user interface and UI module."
We serviced a
BOSCH WASHING MACHINE
Model WGB246AXUC/15
Near Vail, Colorado 81657
Erik
Job Details:
10/08/2025
INSTALL HARNESS/ TEST: PASSJOB COMPLETE
We serviced a
WHIRLPOOL DRYER
Model WED8500DC4
Near Colorado Springs, Colorado 80920
Aaron
Job Details:
10/08/2025
"Idler and rollers have worn from use, removed and replaced components, AF intermittently showing on the UI console, unit has good push, recommend wall vent to be professionally cleared. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Colorado Springs, Colorado 80915
Jacob
Job Details:
10/08/2025
"After installing the new sump assembly and heating element, the dishwasher is functioning as it should. You can hear the water moving around. Liftmos strip installed, no leaks, all is functioning properly."
We serviced a
CAFE REFRIGERATOR
Model CYE22TP4MW2
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
10/08/2025
"MADE AN ADJUSTMENT TO THE DRAWER SO DRAWER CLOSES CORRECTLY, UNIT CHECKED OKAY"
We serviced a
GENERAL ELECTRIC DRYER
Model GTD72EBSN0WS
Near Colorado Springs, Colorado 80924
David
Job Details:
10/08/2025
"Installed exhaust duct, venting better."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Gold Hill, Oregon 97525
Jeff
Job Details:
10/08/2025
"Installed new board i found on truck w11603810 had pressure switch issue tested machine working as should ; (created new UIS, deleted prior attachment to UisID 254922)"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHV
Near Pueblo, Colorado 81008
Domingo
Job Details:
10/08/2025
Replaced pod dispenser with clip and lower sprayer arm test it it test it good I ran a cycle for a 10-15 min no leaks put a leaks strip on everything is working as it should
We serviced a
MAYTAG DRYER
Model MED6500MW0
Near Colorado Springs, Colorado 80911
Charles
Job Details:
10/08/2025
"Lint buildup inside lint chute at rear bulkhead restricts air flow, remove lint and tested"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Ashland, Oregon 97520
Jeff
Job Details:
10/07/2025
Parts but main issue was the install machine way out off level reinstalled ran diagnostic no leaks no errors
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Medford, Oregon 97504
Jeff
Job Details:
10/07/2025
Part installed and working
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW1
Near Medford, Oregon 97504
Jeff
Job Details:
10/07/2025
Installed parts tested machine working as should
We serviced a
MAYTAG WASHER
Model MVW6200KW4
Near Grants Pass, Oregon 97527
Thomas
Job Details:
10/07/2025
Replaced control board. Customer still having issue with washer immediately draining while filling. Customer took drain hose out which was pushed into drain pipe too far. Readjusted hose. Ran tested okay with customer present. No leaks from washer but drain pipe for the house is plugged so water backed up into the garage. Customer is aware of this issue. Advised customer of survey
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo West, Colorado 81007
Domingo
Job Details:
10/07/2025
Replaced control calibrated the control and then ran a diagnostic mode to make sure everything is working as it should and the machine passed I even fill it up and drain it to make sure pump would shut off and it did
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
10/07/2025
"Installed valve, cx needs to replace hot water hose internal seal is damaged"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
10/07/2025
"Installed gearcase, harness and belt, ran cycle with load, runs ok. Called Techline SR-21049599 advised cx to run balanced loads unit working as designed"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
10/07/2025
Installed control board ran test runs all ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS09
Near Monument, Colorado 80132
Ryan
Job Details:
10/07/2025
Gasket looking good and will totally expand now after i showed customer how to use humidity control to turn on heater in mullion. RK
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
10/07/2025
"Heating element and thermostat are shorted out, removed and replaced components, tested unit through diagnostics, working and heating well now. Advised customer of situation and survey."
We serviced a
JENN-AIR RANGE
Model JGCP436HM00
Near Carbondale, Colorado 81623
James R
Job Details:
10/07/2025
"Signed disclaimer. Replaced igniter, burner head and module made some adjustment of nre head and now is working. Please fill out tech satisfaction survey."
We serviced a
JENN-AIR FREEZER
Model JBZFL18IGX10
Near Carbondale, Colorado 81623
James R
Job Details:
10/07/2025
Signed disclaimer. Ice tray was empty when I arrived and icemaker turned off. Put into service test 120 icemaker cycled and passed test. Called whirlpool tech line indicated that customer will need to turn icemaker off when full then once level drops then turn icemaker back on. Ice maker is functioning as should. There is no adjustment.21047705Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Silverthorne, Colorado 80498
Antonio
Job Details:
10/07/2025
Installed new ui panel then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
JENN-AIR REFRIGERATOR
Model JF36NXFXDE01
Near Dillon, Colorado 80435
Antonio
Job Details:
10/07/2025
Installed new led lights then cycled unit back on and all lights are on
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF705HPS04
Near Dillon, Colorado 80435
Antonio
Job Details:
10/07/2025
Installed new water bottle and evap cover then cycled unit back on and water is now dispensing and also advised cx of whlp survey
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Breckenridge, Colorado 80424
Antonio
Job Details:
10/07/2025
Installed new acu and could not test unit due to there's no power
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
10/07/2025
cx complanit - dryer dum part broken - replaced assembly drum - unit is working as designed - survey mentioned
We serviced a
WHIRLPOOL DRYER
Model WED5100HW3
Near Albuquerque, New Mexico 87121
Larry
Job Details:
10/07/2025
Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL VENT HOOD
Model WVW53UC6LS
Near Santa Fe, New Mexico 87505
Jason
Job Details:
10/07/2025
Installed part unit opperation checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS311SDHM11
Near Santa Fe, New Mexico 87505
Antonio
Job Details:
10/07/2025
cx complanit - water leaking - water line that goes straight into the shell of the unit - unit is unrepairable - called technical support to have it documented - SR#21046974
We serviced a
GE W/D STACKED UNIT
Model GUD24ESSM1WW
Near Colorado Springs, Colorado 80906
Earl
Job Details:
10/07/2025
"Customers complaint unit does not fill up with the amount of water. It takes for a full wash cycle. It does vary depending on what cycle is chosen and the unit makes noise. That sounds. Pretty bad. When it is shifting from spent agitate and drain, I found something was stuck under the belt guard, I took that out, it changed the noise a bit part of it is the actuator I explained to where there's fineness, not damaging anything. And the reason the unit does not use a lot of water. Is because it depends on what cycle she uses cause delicates, is never gonna use as much as large cycles. Heavy duty and such unit is operating properly at this time."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Carbondale, Colorado 81623
James R
Job Details:
10/07/2025
Signed disclaimer. Tore apart found heater got too hot and warped. Replaced it and cutoff. Checked vent restriction it is .90+ way too high will not heat properly. Take too long to dry and getting to hot. This will need to be taken care of before the dryer will heat and dry properly. With vent unhook checked cycling temp timed dry and high temp 165 - 130 good unit is operating as should. Please fill out tech satisfasction survey. Thank You.
We serviced a
WHIRLPOOL DRYER
Model WED8127LW2
Near Glenwood Springs, Colorado 81601
Clint
Job Details:
10/07/2025
Customer signed disclaimer. They had parts at home. Tub and rollers. Tub had rusted and had 2 cracks in it. Rollers were worn.Replaced parts and ran unit . Unit ran satisfactory. PLEASE TAKE TECH SURVEY THANKS.Clint/Sean
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW2
Near Los Alamos, New Mexico 87544
Jason
Job Details:
10/07/2025
Checked unit did find evidance of grease and dirt mixed on. suspect sometype of grease was used on shaft. removed residue ran cycle unit opperation checks ok. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Albuquerque, New Mexico 87120
Larry
Job Details:
10/07/2025
Installed control and tested good - Unit is good to go - Survey mentioned
We serviced a
SUBZERO RANGE
Model DF48450F/S/P
Near Silt, Colorado 81652
James R
Job Details:
10/07/2025
Signed disclaimer. Unit was working when arrived went ahead and replaced T-stat all connections to it were ok. Reinstalled unit and test operation. Is working as should. Please fill out tech satisfaction survey. Thank You.
We serviced a
SAMSUNG REFRIGERATOR
Model RF22KREDBSG/AA
Near Colorado Springs, Colorado 80911
Jacob
Job Details:
10/07/2025
"Ice maker was frozen over, upon inspecting the unit I found that the water outlet was frozen over. After cleaning the unit and reinstalling the ice maker, it filled and reset to its original position. Advised customer that the service fee is good for 30 days, as well as our quote. SF $139.95 PAIDPART $212.10MPS $14.50LABOR $199.95TAX $17.39TOTAL $582.89"
We serviced a
MAYTAG M/W OTR
Model MMV4203WS0
Near Santa Fe, New Mexico 87505
Jason
Job Details:
10/07/2025
"Checked unit found magnetron is bad, cx does not wanna repair at this point Auth code: W9A3LF$244.95"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23BB860012AA
Near Newport, Oregon 97365
Nathan
Job Details:
10/07/2025
Huge crack bottom of refer cavitySee photos Called tech line #7006645850Deemed unrepairable
We serviced a
SAMSUNG MICROWAVE
Model ME21DG6300SRAA
Near Colorado Springs, Colorado 80922
Mathew
Job Details:
10/07/2025
"Found bad mag. Replace mag, test op. All okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSG/AA
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
10/07/2025
Replaced parts and cycled all checks ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6200QLAA
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
10/07/2025
Replaced pcb and tested operation all checks ok hass passed
We serviced a
SAMSUNG WASHER
Model WD90F53AVYUS
Near Roseburg, Oregon 97471
Thomas
Job Details:
10/07/2025
Excessive shaking per customer. Performed calibration per Samsung recommendation via one of their elearning videos. HASS passed. Advised customer and they will monitor
We serviced a
SAMSUNG DRYER
Model DVE55CG7100VA3
Near Colorado Springs, Colorado 80924
Mathew
Job Details:
10/07/2025
"Found bad heater, belt off of idler. Replaced heater, motor pulley and belt test op all okay. Found venting crushed, recommend getting venting fixed to not have dry time issues."
We serviced a
FRIGIDAIRE OVEN
Model FPGF3077QFH
Near Colorado Springs, Colorado 80915
Jacob
Job Details:
10/07/2025
"Customer stated that the control was not reacting to their touch, after cleaning the touch panel off it reacted to touch and operated properly. Tested range for temperature, it was within 15-20 degrees from the top to the bottom and is functioning properly as it should."
We serviced a
MAYTAG DRYER
Model Med5630HC1
Near Pueblo, Colorado 81006
Domingo
Job Details:
10/07/2025
Customer said they got a new one no need service
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9675AP/AA
Near Medford, Oregon 97501
Jeff
Job Details:
10/07/2025
Found compressor is locked up. Need compressor dryer. Price total is 1825.71 customer is paying trip wants to discuss further with loved one if they want to proceed Auth v9va4e. Id 2981012
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Sisters, Oregon 97759
Richard
Job Details:
10/07/2025
"Tested unit all temps. Check good found vent restriction, Explain to customer venting is crucial for the dryer to work properly. Long dryer run no airflow going to the outside. Customer declined contact vent company."
We serviced a
WOLF WALL OVEN
Model DO30-2F/S
Near Colorado Springs, Colorado 80921
Charles
Job Details:
10/07/2025
"Installed user interface console and display board, set clock and tested both ovens. Notes say labor due, customer disputed, spoke to Sterling ok to waive labor due to wait."
We serviced a
LG DISHWASHER
Model LDTH7972S.ASSESNA
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
10/07/2025
Replaced rails and tested operation all checks ok
We serviced a
LG W/D STACKED UNIT
Model F3S1CWK2WV.ABWEEUS
Near Breckenridge, Colorado 80424
Antonio
Job Details:
10/07/2025
Installed new wire harness and then ran a cycle for proper operation and unit tested good
We serviced a
LG WASHING MACHINE
Model WM8100HVA
Near Monument, Colorado 80132
Brandon
Job Details:
10/07/2025
"Bad pump, replaced pump and tested operation all checks ok"
We serviced a
LG ELECTRIC RANGE
Model LREL6323S.FSTLLGA
Near Colorado Springs, Colorado 80910
Jacob
Job Details:
10/07/2025
"After swapping all rotary switches, the machine is operating as it should."
We serviced a
SAMSUNG WASHER
Model WF50A8600AE
Near Colorado Springs, Colorado 80915
Mathew
Job Details:
10/07/2025
"Found upper weight broken off of plastic drum front. Recommend tub front, weights, mounting screws, diaphragm. Cx says they have 5 year warranty. Inform Cx that they will have to contact warranty directly to open ticket for repair, Svf will need to be collected as this ticket is put in out of warranty. $139.95 CC Auth# 994X3WSvf 139.95MPs 14.50Weight x 3 (52.26 ea. )$156.78tub weight 268.80Labor $349.95"
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GBS0
Near Sisters, Oregon 97759
Richard
Job Details:
10/07/2025
"Tested unit found hinge pin broken on the right side causing door to sag and pop when opened.customer declined further repair on unit and opted to purchase a new unit, customer paid by CC ,,,, Auth#34NH4Y,,TRAN#2981466"
We serviced a
ELECTROLUX DRYER
Model EFME617STT0
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
10/07/2025
Replaced broken belt and tested operation ok. Picked up part from Marcone and was not truck stock.RKPart 69.98Tax 5.73Materials 14.50Labor 199.95S/C 159.95Total 450.08Auth MJM4W4; used 1 134719300 (BELT) from stock
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS01
Near Colorado Springs, Colorado 80924
Ryan
Job Details:
10/07/2025
"Iinstalled new auger motor and left middle drawer. All items are now in workng order, and working properly. RK"
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Frisco, Colorado 80443
Erik
Job Details:
10/07/2025
CONNECT TO SMARTHQ SERVICE: F18 DRAIN PUMP CLEARING ALGORITHM FAILEDDRAIN LINE 10- 12' INTO STANDPIPE -WATER SYPHON RELEASED WHEN REMOVED/ TEST: PASSUSE STRAP TO SECURE DRAIN IN STAND PIPE ( MUST SEE RIBS FOR PROPER HIEGHT)JOB COMPLETE
We serviced a
GE DISHWASHER
Model GDF450PSR6SS
Near Silverthorne, Colorado 80498
Erik
Job Details:
10/07/2025
ACCESS WITH ROP MGMTINSTALL DIVERTER/ TEST: PASSJOB COMPLETE
We serviced a
PROFILE REFRIGERATOR
Model PFE28KYNKFS
Near Monument, Colorado 80132
Ryan
Job Details:
10/07/2025
Replaced main control board and UI due to intermittent electrical/cooling issues. RK
We serviced a
GE DRYER
Model GFD55ESSN2WW
Near Silverthorne, Colorado 80498
Erik
Job Details:
10/07/2025
ACCESS WITH PROP MGMTOBSTRUCTION IN FAN HOUSING - REMOVE AND TEST: PASSJOB COMPLETE
We serviced a
GE DRYER
Model GTD48EASW0WB
Near Colorado Springs, Colorado 80908
David
Job Details:
10/07/2025
"Replaced switch and button, working good."
We serviced a
FRIGIDAIRE RANGE
Model GCFI3060BF
Near Newport, Oregon 97365
Nathan
Job Details:
10/07/2025
Not proper power supplied to unit 185v on one leg 60v on the other leg Customer to replace breaker and line to unit
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FPRU19F8WFB
Near Bend, Oregon 97707
Levi
Job Details:
10/07/2025
I found loose connector on power cord inside of system compartment. Reconnected tested and all checks okay
We serviced a
FRIGIDAIRE W/D STACKED UNIT
Model FLCE7522AW4
Near Sisters, Oregon 97759
Richard
Job Details:
10/07/2025
"Tested unit unable to duplicate issue,removed covers found no issues at this time all checks good at this time."
We serviced a
ELECTROLUX WASHER
Model ELFW7637AT2
Near Peyton, Colorado 80831
David
Job Details:
10/07/2025
"Installed top panel, all good."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LFTR2045VFB
Near Pueblo, Colorado 81004
James
Job Details:
10/07/2025
Found lose wire around evap fan occasionally hitting blades. Secured and tested all ops test good
We serviced a
LG WASHER
Model WM8000HVA
Near Colorado Springs, Colorado 80906
Jacob
Job Details:
10/07/2025
"Upon testing the machine, I found that there is a loud rumbling/scraping noise when turning the tub by hand. Further inspection showed that the spider arm and rear drive bearing have gone bad. Shipping bolts were in case, not connected to tub. (Photo provided)SF $139.95Part $427.70Part $171.68MPS $14.50Labor $349.95Tax $49.15Total $1152.93"
We serviced a
DACOR RANGE
Model DOC30P977DS/DA
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
10/07/2025
Replaced microwave PCB both door switches and display panel and tested operation all checks ok
We serviced a
SUBZERO REFRIGERATOR
Model 690/S
Near Colorado Springs, Colorado 80919
Charles
Job Details:
10/07/2025
"Vacuum condenser flashing on display, reset power to clear, wants drain tube replaced in fridge, drain tube 1601400, Service fee $189.95, Labor $295.95, MPS $14.50, Part $104.36, Tax $8.56, Total $613.32, declined estimate, paid service fee autho J9AFAC"
We serviced a
THERMADOR WINE COOLER
Model T24UW925RS/01
Near Breckenridge, Colorado 80424
Erik
Job Details:
10/07/2025
INSTALL DOOR ASMJOB COMPLETE
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB8600QLAA
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
10/07/2025
"Leaking at lokring again, cx does not to repair"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9380SG
Near Monument, Colorado 80132
Brandon
Job Details:
10/07/2025
Replaced gasket and tested operation all checks ok
We serviced a
WHIRLPOOL WASHER
Model MVW5435PW1
Near Roseburg, Oregon 97470
Thomas
Job Details:
10/07/2025
Replaced main control board. Ran tested okay no leaks. Advised customer of survey
We serviced a
LG RANGE
Model LREL6323S/00
Near Colorado Springs, Colorado 80918
Charles
Job Details:
10/07/2025
Replaced infinite switches for front elements
We serviced a
GE WASHER
Model GUD27ESSM1WW
Near Breckenridge, Colorado 80424
Erik
Job Details:
10/07/2025
ACCESS FROM TENNANTCONNECT TO SMARTHQ SERVICE: FILL TEST: PASS/ SPIN TEST: PASSCX EDUCATION - MAX FILL LEVEL 2/3 TUB 27 GAL. ( CONFIRMED WITH SMARTHQ)CX MUST USE DEEP FILL/ DEEP RINSEJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
10/07/2025
"Belt slipping on drive pulley causing noise, removed and replaced components, tested unit through diagnostics, working well now, installed litmus strip and advised customer of situation and survey."
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Albuquerque, New Mexico 87112
Jason
Job Details:
10/06/2025
Checked unit found oven burner flame was getting too much air causing flame to be pushed away from burner. adjusted air shutter. burner flame checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ19
Near Butte Falls, Oregon 97522
Jeff
Job Details:
10/06/2025
Installed parts tested harvested and fills

