We serviced a
MIDEA FREEZER
Model MRU21F2AWW
Near Colorado Springs, Colorado 80938
Brandon
Job Details:
06/02/2025
"No errors, compressor clinking on and off, called midea tech support they said replace compressor and starter relay, sealed system repair needed, svf paid $139.95 CC Auth# H4HCV4 , labor $695.95, mps $14.50, refrigerant $255.95"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23HCDBSR/AA
Near Colorado Springs, Colorado 80923
Mathew
Job Details:
06/02/2025
"Defrost ice room. Remove auger and icemaker. Dry room. Adjust water fill line. Re seal room. Install old parts. Test op, icemaker working as expected. If issue persists unit will need ice maker replacement. $139.95 CC Auth# 39CFFRSvf 139.95."
We serviced a
LG OTR MICROWAVE
Model MVEM1721F.BRSELGA
Near Colorado Springs, Colorado 80909
David
Job Details:
06/02/2025
Installed ordered parts. Tested and is heating good.
We serviced a
LG WASHER
Model WM4000HWA.ABWEVUS
Near Monument, Colorado 80132
Dvante
Job Details:
06/02/2025
Replaced dispenser. Tested unit and water was able to rinse the softener properly. Advised customer to have water in softener area due to the softener customer uses.
We serviced a
LG DRYER
Model DLE7150M.ABMEEUS
Near Monument, Colorado 80132
Charles
Job Details:
06/02/2025
"Tripping breaker when not in use, never trips when in use, customer said it was 4 flashes on breaker that is over voltage error. Max amp draw 24.9"
We serviced a
LG REFRIGERATOR
Model LRFXC2606S.ASTCNA0
Near Gypsum, Colorado 81637
Antonio
Job Details:
06/02/2025
Found debrie in filter water housing preventing filter from Being installed properly. Cleared debrie and installed water filter unit testing good
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS03
Near Albuquerque, New Mexico 87120
Larry
Job Details:
06/02/2025
CX complaint - Freezer not at 0 - Checked and found mastic in the condenser fan - Removed mastic and tested good - Unit is operatign as designed
We serviced a
FRIGIDAIRE DISHWASHER
Model FGID2476SF7A
Near Colorado Springs, Colorado 80915
Mauricio
Job Details:
06/02/2025
129.22 drain pump300 control boards$139.95 CK Auth# F9WTFYUnit not draining needs pcb board and drain pump cx would not like to proceed
We serviced a
SAMSUNG DRYER
Model DV48H7400EW/A2
Near Monument, Colorado 80132
Charles
Job Details:
06/02/2025
"Idler pulley failed, need pulley DC93-00634A, Service fee $149.95, Labor $239.95, MPS $14.50, Part $97.56, Tax $8.00, Total $499.96 paid autho K9KT9T"
We serviced a
GE REFRIGERATOR
Model PVD28BYNCFS
Near Pueblo, Colorado 81003
James
Job Details:
06/02/2025
Installed ordered parts tested ops all ckok collected 229.95 $229.95 CC Auth# N4J9U9
We serviced a
HOTPOINT DRYER
Model HTX26EASW0WW
Near Grand Junction, Colorado 81503
Sean
Job Details:
06/02/2025
Checked the unit MN SN POP Customer signed disclaimer.Turned the unit on and found the belt was off.Removed the top panel and front door panel Reattached the belt and drum.Reassembled the unit.Tested 0
We serviced a
PROFILE REFRIGERATOR/TOP
Model PVD28BYNHFS
Near Grand Junction, Colorado 81504
Sean
Job Details:
06/02/2025
Unplugged the unit and removed the right hand FF door Removed all components and put them on the new door Installed the new door on the unitUnhooked the water and all the power to the left door .Removed the water filter and valves and ice maker from the door and installed them on the new door hooked up the ice maker . And water lines and reassembled the left door.Put it back on the unit. Put on the gaskets and the center divider. Installed the new door on the unit and tested all doors look good and are functioning as designed by factory.Thank you and if you are satisfied with the service I have provided you with today then please share your experience with others and fill out a technician survey.Thank you .Sean D-3 Appliance
We serviced a
GE DISHWASHER
Model GDT550PGR7WW
Near Vail, Colorado 81657
Erik
Job Details:
06/02/2025
unit not draining -remove kick plate and remove drain pump motor - small machine screw in drain pump - clear pump and reinstall/ test: PASSJOB COMPLETE
We serviced a
HAIER REFRIGERATOR
Model QJS15HYRBFS
Near Eagle, Colorado 81631
Erik
Job Details:
06/02/2025
ACCESS WITH KEY FROM CONSTRUCTION TRAILER - UNIT UNOCCUPIED/ NEW CONSTRUCTIONVERIFY UNIT AND TEST ICE MAKER: PASSSCRATCHES ON BOTTOM DRAWER*see quick pics - CX MUST GET DOOR (WR78X38390) FROM DEALER FOR REPLACEMENTJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
GE REFRIGERATOR
Model PWE23KYNIFS
Near Fruita, Colorado 81521
Josh
Job Details:
06/02/2025
"Customer signed disclaimer, verified MN SN POP. Technician confirmed correct components received in good condition. Technician installed replacement dual water valve and icemaker assembly. Technician tested water dispenser, and observed productive fill of icemaker. Unit is functioning properly within manufacturer specifications. Thank you for allowing us to service your refrigerator today! Please take a moment to let us know how weve done by completing our technician satisfaction survey. Call with any questions, and have a great day!"
We serviced a
GE DISWASHER
Model CDT828P2V1S1
Near Eagle, Colorado 81631
Erik
Job Details:
06/02/2025
construct main conduit/ docking port/ hub & impeller - INSTALL AND CORRECT METAL MOUNTS *see quick pics ( missing from initial install - HOME DEPOT)remove heating element and MCB - REPLACE/ TEST: PASSJOB COMPLETE - PARTS LEFT WITH CX/ MISSING PARTS NOTED ON PACKING LIST ALSO WITH CXSUGGEST AFFRESH FOR DESCALING
We serviced a
GE DRYER
Model PFD95ESPW0GN
Near Pueblo, Colorado 81007
Domingo
Job Details:
06/02/2025
Replaced motor and test it and test it good it heat up
We serviced a
CAFE RANGE
Model CHP90361T1BB
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
06/02/2025
REPLACED PART AND UNIT CHECKED OKAY
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814WBA
Near Pueblo, Colorado 81005
Domingo
Job Details:
06/02/2025
Replaced defrost timer refrigerator came on everything is working fine
We serviced a
SAMSUNG DRYER
Model DV40J3000EW/A2
Near Colorado Springs, Colorado 80924
Mathew
Job Details:
06/02/2025
"Found blower motor had a giant lint ball in it. Obstructing motor. No op. Cleared out obstruction, clean out unit. Test op. All okay. $139.95 CK Auth# J4R4W3"
We serviced a
WOLF MICROWAVE
Model MD30TE/S
Near Colorado Springs, Colorado 80921
Ryan
Job Details:
06/02/2025
Replaced monitor switches and fuse.Tested operation ok.Inst. customer on correct use.RK
We serviced a
DACOR MICROWAVE
Model PCOR30S
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
06/02/2025
"Replaced magnetron and rectifier. Tested unit, no loud noises. Unit is heating and working as designed."
We serviced a
JENN-AIR COOKTOP
Model JIC4536XS00
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
06/02/2025
Right side power module is shorted and blowing fuses. Needs new power module. Parts are no longer available. RK159.95Auth TE4ECL
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB86004MAA
Near Colorado Springs, Colorado 80920
Brandon
Job Details:
06/02/2025
"Replaced compressor and drier, checked evaps all checks ok, vacuumed and charged unit, hass passed"
We serviced a
BOSCH DISHWASHER
Model SHX78CC5UC/48
Near Colorado Springs, Colorado 80921
Charles
Job Details:
06/02/2025
"Replaced water switch per tech line for error code E6A-00. Started cycle, unit filled and is running."
We serviced a
BOSCH DISHWASHER
Model SHP65CM5N/25
Near Grand Junction, Colorado 81507
Sean
Job Details:
06/02/2025
Opened unit and pulled it out Turned off water and removed the water distributor.Unhooked the wires.Installed the new water dispenser and hooked wires back out reassembled the unit and tested the unit tested good. Operating as designed by factory.If you are satisfied with the service I have provided you with today then please share your experience with others and go online and fill out a technician survey.Thank you Sean D-3 Appliance.
We serviced a
SAMSUNG REFRIGERATOR
Model RF24R7201SR/AA
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
06/02/2025
"Error 39c, ice maker error, thawed ice maker and cleared all ice from ice room, cycled ice maker it cycled, need to allow time to see if ice maker needs to be replaced, informed cx of cost to replace ice maker if issue persists, svf paid $139.95 CC Auth# E3N39Y, $400.29 due to replace ice maker"
We serviced a
SCOTSMAN ICE MACHINE
Model SCCG30MA-1SU
Near Colorado Springs, Colorado 80919
Charles
Job Details:
06/02/2025
"Door not closing, plastic hinge cover not snapped on top hinge and not allowing door to close. Snapped in place and door closed, customer requested to remove covers. Service fee $159.95 paid autho 3UWJ3L"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ
Near Colorado Springs, Colorado 80920
Mauricio
Job Details:
06/02/2025
Replaced housing tested unit drained fine unit tested to spec also shop vac drain hose
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
06/02/2025
"Lid switch is shorted out, removed and replaced assembly, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MEDB835DW4
Near Redmond, Oregon 97756
Richard
Job Details:
06/02/2025
"Tested unit, unit working as designed customer has a vent restriction. Needs vent cleaned by a professional vent service."
We serviced a
WHIRLPOOL DRYER
Model WED6150PW
Near Fountain, Colorado 80817
Carlos
Job Details:
06/02/2025
Installed heater runs all ok
We serviced a
GE REFRIGERATOR
Model GFE28GYNFS
Near Colorado Springs, Colorado 80923
Ryan
Job Details:
06/02/2025
"Found unit working fine. Confirmed correct temps.Customer needed to wait long enough for unit to stabilize.Unit was empty,customer does not run A/C , and conditions are very humid. RK"
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Colorado Springs, Colorado 80923
Dvante
Job Details:
06/02/2025
"Checked unit, didnt find any rocks or loose change inside. Asked customer if items were overloaded and was told no. Tested unit 3 times, no noises inside. Unit is operating as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Pueblo, Colorado 81004
Domingo
Job Details:
06/02/2025
No one was home call office they call left him voice mail
We serviced a
GE DISHWASHER
Model GDP665SYN8FS
Near Colorado Springs, Colorado 80911
David
Job Details:
06/02/2025
"Installed ordered parts, ran dishwasher to confirm operation, all good."
We serviced a
SAMSUNG DISHWASHER
Model DW80R5060U
Near Colorado Springs, Colorado 80927
Mathew
Job Details:
06/02/2025
"Found machine full of water. Force drain. Evacuate water with pump. Run through diagnostic cycle. Found excess suds in machine. Ran multiple tests, all okay. Unit working as expected."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
05/30/2025
Replaced evaporator fan motor assembly. Checked inside fridge section and found ice blockage from damper. Steamed ice off. Tested unit and its operating properly with no issues.$229.95 CC Auth# 3YCLJ3
We serviced a
MAYTAG WASHER
Model MVW6230RHW2
Near Grants Pass, Oregon 97527
Thomas
Job Details:
05/30/2025
Was informed that customer canceled
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Medford, Oregon 97504
Jeff
Job Details:
05/30/2025
Found buttons stuck would need board and console called safety sr 7741635072 customer doesn't want to repair.
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ3
Near Terrebonne, Oregon 97760
Richard
Job Details:
05/30/2025
Removed and installed new sump assembly with wash motor cycle tested unit. No leaks at time of repair job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Medford, Oregon 97504
Jeff
Job Details:
05/30/2025
"Unit was under charged,recharged unit cooling as should."
We serviced a
MAYTAG WASHER
Model MVW5435PW0
Near Redmond, Oregon 97756
Richard
Job Details:
05/30/2025
"Tested unit found error code called tech support ran diagnostic,and ran unit and were unable to duplicate issue per tech check pressure tube connection at tub and run a 1/8 driil bit in tube and clear any debris if any for proper pressure to control , file # 7741666124."
We serviced a
WHIRLPOOL DRYER
Model WED6150PW0
Near Merlin, Oregon 97532
Thomas
Job Details:
05/30/2025
Unable to verify complaint. Ran tested okay with customer present. Answered customer questions
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Medford, Oregon 97501
Jeff
Job Details:
05/30/2025
Found hot water line leaking. Had no gasket . Installed gasket no leaks.
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Colorado Springs, Colorado 80910
Carlos
Job Details:
05/30/2025
"7741670172 loading issue, cx education on proper loading unit working as designed"
We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
05/30/2025
Installed control board ran calibration and diagnostic cycle runs all ok if ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
05/30/2025
Installed sump assembly unable to run tests unit is uninstalled in a storage unit
We serviced a
WHIRLPOOL DRYER
Model WED6150PB0
Near Colorado Springs, Colorado 80916
David
Job Details:
05/30/2025
"Checked dryer, dryer is heating. Voltage is 218 - 220. Vent was a little restricted. Good air flow. Dry times will be longer with lower voltage. Suggested cx have utilities check voltage into house."
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ5
Near Monument, Colorado 80132
Dvante
Job Details:
05/30/2025
Replaced control board. Fan inside is operating now. Unit is functioning as designed.
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Colorado Springs, Colorado 80921
Jerimiah
Job Details:
05/30/2025
Installed replacement tt motor. Unit check ok.
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Pueblo West, Colorado 81007
Domingo
Job Details:
05/30/2025
Replaced slider and clutch test it it pass rana cycle and it finish with no problem. If the banging continues it will need a gear case W11449841
We serviced a
MAYTAG DRYER
Model MED5430MW0
Near Peyton, Colorado 80831
Aaron
Job Details:
05/30/2025
"Unit canceling cycle ten minutes in, inspected unit, exhaust thermistor connection at control not fully engaged, corrected and monitored unit, working and heating well now, tested for 20 minutes without cancelation, polarity is good and wired correctly at terminal block. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
05/30/2025
"Installed securing clip for drain pump wire, all checks ok"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
05/30/2025
"Checked unit, found the reasoning on why customer was getting the check vent error was due to the vent hose bent causing no airflow. Fixed vent. Unit is now getting proper airflow."
We serviced a
MAYTAG WASHER
Model MVW7232HC2
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
05/30/2025
"Checked unit, customer was continuously getting an unbalanced error. Replaced suspension rods. Tested unit. No unbalance. Advised customer to not overload unit to cause the error."
We serviced a
WHIRLPOOL DRYER
Model WED6150PW0
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
05/30/2025
"Installed front panel, door nozzle and valve"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Colorado Springs, Colorado 80915
Aaron
Job Details:
05/30/2025
"Removed and replaced lid assembly, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Colorado Springs, Colorado 80915
Aaron
Job Details:
05/30/2025
"Removed and replaced UI console, programmed and tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID DISHWASHER
Model KUDP02FRSS2
Near Colorado Springs, Colorado 80909
David
Job Details:
05/30/2025
"Installed ordered parts, door not flopping down when opened. Have to press door closed for it to latch."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SHZ1
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
05/30/2025
"F6E4 error code upon arrival, debris under float switch, confusing control with fill level, corrected and tested unit, working well now, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
05/30/2025
cx complanit - loud noise ( gearcase) - used all parts shiped to cx home - unit is working as designed - survey mentioned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ13
Near Rio Rancho, New Mexico 87144
Antonio
Job Details:
05/30/2025
cx complanit - doors not aligned - adjusted the right and left wheels to make the doors even - unit is working as designed - surevy mentioned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ00
Near Los Lunas, New Mexico 87031
Larry
Job Details:
05/30/2025
Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Albuquerque, New Mexico 87106
Jason
Job Details:
05/30/2025
Checked unit found unit has one leg of power dropping out. spoke to landlord about power issue. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Rio Rancho, New Mexico 87144
Antonio
Job Details:
05/30/2025
"cx complanit -spray arm not working - replaced pump motor assembly,unit is working as designed -survey mentioned"
We serviced a
WHIRLPOOL RANGE
Model WFES3030RS0
Near Belen, New Mexico 87002
Larry
Job Details:
05/30/2025
CX complaint - Door not aligned - Inspected unit and fount the door hinge misaligned in reciever - Aligned door hinge and tested good - Unit is good to g - Survey mentioned
We serviced a
JENN-AIR ICE MACHINE
Model JUIFX15HX00
Near Bend, Oregon 97702
Levi
Job Details:
05/30/2025
"I do not need to return to customers home, yesterday I power cycled the machine and it has been making ice since yesterday afternoon. Job complete"
We serviced a
WHIRLPOOL DRYER
Model WED8127LW1
Near Albuquerque, New Mexico 87123
Jason
Job Details:
05/30/2025
Installed cuttoff and element unit opperation checks ok. spoke to cx about review
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Albuquerque, New Mexico 87110
Jason
Job Details:
05/30/2025
Installed parts checked im opperation unit checks ok. spoke to cx about review
We serviced a
KITCHENAID WALL OVEN
Model KOCE500ESS09
Near Albuquerque, New Mexico 87106
Larry
Job Details:
05/30/2025
Installed Parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Albuquerque, New Mexico 87108
Jason
Job Details:
05/30/2025
Installed pump motor assy ran diagnostic cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model MSS25C4MGZ06
Near Colorado Springs, Colorado 80911
Mauricio
Job Details:
05/30/2025
Ice maker 138.07User interface 281.14Problem verified no ice spoke with whirlpool recommend parts on order ice maker and UI$139.95 CC Auth# 33LXM92435163 trans ID
We serviced a
SUBZERO REFRIGERATOR
Model 590
Near Colorado Springs, Colorado 80921
Ryan
Job Details:
05/30/2025
"Found frozen drain pan due to being crooked due to sagging evaporator assembly. Tried to straighten pan a bit,onfirmed drain is clear and drain heater is operating properly. If happens again customer may need major overhaul that he is not interested in at this time. RK189.95Auth HXN4C3"
We serviced a
ELECTROLUX FREEZER
Model LFFU14F5HWH
Near Colorado Springs, Colorado 80905
Ralph
Job Details:
05/30/2025
"unit has an ineffiecient compressor sill need to be replaced, cust not repairing...autho no. MTKH4M"
We serviced a
SAMSUNG DISHWASHER
Model DW80B7070US/AA
Near Colorado Springs, Colorado 80923
Brandon
Job Details:
05/30/2025
"Drain plug not removed on disposal, removed and tested operation all checks ok"
We serviced a
WHIRLPOOL RANGE
Model WFE540H0ES0
Near Colorado Springs, Colorado 80915
Jerimiah
Job Details:
05/30/2025
"Unit not getting to proper temps baking, producing 240vac from board, broil element at 15.7 ohm, bake element at 1.1meg ohm. Bake element needs replacing, rcvd thru SSB. Labor was $219.95. $478.49 CC Auth# 39UXK4. Disclosed survey to cust fcc 5star.W10779716 bake element $96.20"
We serviced a
WHIRLPOOL DRYER
Model WED92HEFC0
Near Colorado Springs, Colorado 80926
David
Job Details:
05/30/2025
"Heater element burned-out, replaced and is heating good now"
We serviced a
WHIRLPOOL DRYER
Model WED9151YW0
Near Monument, Colorado 80132
Dvante
Job Details:
05/30/2025
Replaced pulley idle and belt. The drum is spinning freely now. Unit is operating as designed.$199.95 CC Auth# 349PUT
We serviced a
ADMIRAL REFRIGERATOR
Model HMG181030
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
05/30/2025
"UNITR IS AN R12 UNIT, AND HAS A LEAK, UNIT WOULD BE TOO COSTLY TO REPAIR...AUTHO NO. 3WNL33"
We serviced a
LG REFRIGERATOR
Model LFC22770SW.ASWCNA0
Near Colorado Springs, Colorado 80918
Brandon
Job Details:
05/30/2025
"Replaced compressor and drier, updated s/w on PCB, vacuumed and charged unit"
We serviced a
LG WASHER
Model WM8100HVA
Near Pueblo, Colorado 81001
James
Job Details:
05/30/2025
Installed ordered parts tested ops all ckok left litmus.
We serviced a
LG DISHWASHER
Model LDTH5554D.ABDESNA
Near Monument, Colorado 80132
Ryan
Job Details:
05/30/2025
Removed and reinstalled pump and drip tray drain that may have been cause of water getting into pan causing E1 error. Reinstalled unit and tested operation completely. All now checks ok. RK
We serviced a
LG DRYER
Model DLEX4000B
Near Colorado Springs, Colorado 80908
Jerimiah
Job Details:
05/30/2025
"Unit getting d80 and d90 error codes, Cust not using dryer sheets. Previous work has been done on exact same model of replaced unit that had a large wad of lint in base of unit. Did diags with Techline, found o restrictions or error codes coming back once external venting was removed from unit, took unit apart and found very little buildup inside unit. Disclosed bends in venting could cause major troubles but Cust has very few bends currently. Unit ran with no error codes, unit check ok"
We serviced a
SUBZERO BAR FRIDGE
Model 245RFD
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
05/30/2025
"Found unit shutting down compressor on overload due to clogged condenser coils. Brushed cleaned off coils and tested unit ok.Temps were down to 35 degrees in 15 minutes.Any further problems or diagnosis would require unit to be running for 24 hours. But all checks ok. RKCustomer had to run off to meeting, please bill customer 159.95and for second appliance at same address 109.95 (548816)"
We serviced a
SUB ZERO BAR FRIDGE
Model 245RFD
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
05/30/2025
"Found door not shutting causing frost build-up inside unit. Made adjustment to door and is now closing properly. Started up unit and is now cooling. RKAny further problems would require new hinge, bracket, upper and lower cams .But all checks ok at this time.Please bill customer as he was unavailable after signing waivers he had to run off to appointment"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Ashland, Oregon 97520
Jeff
Job Details:
05/30/2025
Customer instruct on frig use. Paid trip 139.95 id 2433935. Auth yhf4hp
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
05/30/2025
"Removed and replaced evaporator fan motor assembly, unit needs time to cool, tested operation through diagnostics. Advised customer of 5 star survey. Total due was previously paid."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Colorado Springs, Colorado 80905
Mauricio
Job Details:
05/30/2025
Steamed ice area if problem prosody recommend part needed will be a new ice maker part number da97-15217d $139.95 CK Auth# F9WTFY2434352
We serviced a
KITCHENAID RANGE
Model KSDG950ESS1
Near Monument, Colorado 80132
Dvante
Job Details:
05/30/2025
"Replaced bake element. Tested unit, unit heating properly. Unit is operating as designed."
We serviced a
SAMSUNG REFRIGERATOR
Model RF263TEAESG/AA
Near Pueblo, Colorado 81001
Domingo
Job Details:
05/30/2025
Heater defrost DA47-00244W and refrigerator temp sensor DA32-10104N and evap fan DA81-06013A test it bad customer decided want to decline further services sc 139.95 customer pay see pic for authorization
We serviced a
GE WASHER
Model HTW265ASW0WW
Near Grand Junction, Colorado 81504
Sean
Job Details:
05/30/2025
Open and removed the control panel and door panel.Unhooked the door switch.and removed it.Installed the new door switch. Reassembled the unit.Plugged the unit in and tested. Filled the unit on a normal until it started to agitated.Ran a drain cycle to end. Started a quick wash.Watched the unit fill and start.Tested the unit good.Please fill out a technician survey and let other people know about your experience.
We serviced a
GE REFRIGERATOR
Model GIE19JSNCRSS
Near Grand Junction, Colorado 81505
Sean
Job Details:
05/30/2025
Opened back and drained refrigerant.Unbraized the compressor and filter drier.Placed new compressor/fd in and brazed them in place Pressure checked with nitrogen.Pulled vacuum to 400mic and charged the unit with 1.58oz r600.Replaced the start components and restored power to unit.Watched the unit start and watched pressure stabilize.Watched the unit drop to 30? Tested unit good.Thank you please fill out a technician survey.
We serviced a
GE WASHER
Model GFW6555PV0DS
Near Grand Junction, Colorado 81507
Sean
Job Details:
05/30/2025
Checked the package.Customer signed disclaimer.Removed control and unhooked the door panel from the unit Unhooked the security ring from outside gasket and removed door panel . Removed the inside ring and removed the gasket.Placed the new gasket and reinstalled the rings.Reassembled the unit and restored the power. Tested the unit on quick wash with max water .Unit filled and ran the cycle unit did not leak .Unit operating as designed by factory.If you are satisfied with the service I have provided you with today then please share your experience with others and go online fill out a technician survey.Thank you.SeanD-3 A-OK
We serviced a
PROFILE REFRIGERATOR
Model PJE23BYWBFS
Near Frisco, Colorado 80443
Erik
Job Details:
05/30/2025
install/ test: PASSJOB COMPLETE
We serviced a
PROFILE MICROWAVE OVEN
Model PVM9215SK6SS
Near Frisco, Colorado 80443
Erik
Job Details:
05/30/2025
install door JOB COMPLETE
We serviced a
GE DISHWASHER
Model GDF460PST6SS
Near Grand Junction, Colorado 81501
Sean
Job Details:
05/30/2025
Removed the front door to the washer.Unhooked the wiring and removed the inside panel.Unhooked the control panel and replaced it with the new one Removed the overlay and installed a new one.Reassembled the unit and tested the unit starts and runs.Unit operating as designed by factory Thank you.Please fill out a technician survey.
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Palisade, Colorado 81526
Sean
Job Details:
05/30/2025
Installed the new belt onto the unit reassembled the unit and tested.The unit tested good Thank you and if you are satisfied with the service I have provided you with today then please share your experience with others and fill out a online technician survey SeanD-3 A-OK appliance
We serviced a
HOTPOINT DISHWASHER
Model HDF330PGR6BB
Near Colorado Springs, Colorado 80916
Mathew
Job Details:
05/30/2025
Replace faulty door seal. Test op. All okay.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2633AS4
Near Grants Pass, Oregon 97526
Thomas
Job Details:
05/30/2025
Found big crack in side cabinet of freezer. Customer purchased fridge in March. Did not even take it out of the box for about a month due to remodeling the house. Found crack immediately after opening freezer door for the first time. Spoke to Gatey with Electrolux TS. Performed video broadcast to show crack. He gave me reference # 1003251040. Advised customer of issue