We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Grants Pass, Oregon 97527
Thomas
Job Details:
05/19/2025
F8E4 error per notes. Small leak from water hose connector. Tightened connector and ran tested okay with customer present. No leaks. Advised customer of survey
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC136RPS00
Near Bend, Oregon 97702
Richard
Job Details:
05/19/2025
Replaced high voltage board and control for erratic operation programmed control set temps all tested fine at this time unit working as designed .
We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Medford, Oregon 97504
Jeff
Job Details:
05/19/2025
"Pulled machine apart unplugged coin catch, reset unit and tested working as should."
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
05/19/2025
"Installled capacitor and actuator, cx needs plumber to unclog drain"
We serviced a
WHIRLPOOL DISHWASHER
Model WDPS7024RZ0
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
05/19/2025
Replaced wheel tub and screws. No leaks when running diagnostic test. Unit is operating as designed.
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS3
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
05/19/2025
Installed console ran tests runs all ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ13
Near Colorado Springs, Colorado 80920
Dvante
Job Details:
05/19/2025
"Checked unit, found the thermistor is open and diffuser is left open causing food to be frozen. Replaced diffuser. Diffuser is opening and closing properly. Unit is operating as designed."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
05/19/2025
"Checked unit, found the loud squealing coming from the belt and pulley. Also saw a lot of lint on the ground. Cleaned the lint up and replaced the pulley and belt. Advised customer to make sure the lint filter is cleaning after every cycle."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ17
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
05/19/2025
"Installed water valve ran tests runs all ok. Water valve was broken, caused water damage to back of unit floor down to floor bellow"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ18
Near Pueblo West, Colorado 81007
James
Job Details:
05/19/2025
Found condenser vibrating against frame causing unit to make noise. Secured sound dampening material in between frame and condenser. Noise stopped.
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Grand Junction, Colorado 81504
Josh
Job Details:
05/19/2025
"Customer is signed disclaimer. Verified MN SN. Customer representative (school admin) is unable to access POP. Technician verified correct component received in good condition. Technician installed replacement dual water valve and reassembled unit, and corrected hot/cold line connection, performed test cycle, confirming proper operation and hot water fill. Unit is now functioning properly, within manufacturer specifications."
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Grand Junction, Colorado 81507
Josh
Job Details:
05/19/2025
"Customer signed disclaimer, verified MN SN POP.Tech confirmed correct components received in good condition. Technician installed replacement motor and blower, as well as the push to start switch. Tech performed test cycle confirming proper operation of unit. Unit is functioning properly within manufacturer specifications."
We serviced a
MAYTAG RANGE
Model MFES4030RW0
Near Grand Junction, Colorado 81505
Josh
Job Details:
05/19/2025
"Customer signed disclaimer. Verified MN SN.Customer states that unit is getting excessively hot on range top surface and top left fascia and door. Tech confirmed customer concern, further inspection found that the unit is approximately 3/8 out of level, high front bias. Technician leveled unit, primarily by lifting rear feet, finding that the right rear foot to be damaged and unable to be properly adjusted and kept in position due to damaged thread, tech replaced foot from stock on truck. Front feet are fully retracted, and after leveling unit, glass top is approximately 1/4 above counter-top, but cannot be properly adjusted lower due to flooring. Technician performed test cycle. Technician confirmed that unit is functioning properly within manufacturer specifications."
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Grand Junction, Colorado 81507
Josh
Job Details:
05/19/2025
"Customer signed disclaimer. Verified MN SN. Customer is searching for POP and will txt to tech.Customer states that unit squeaks during operation. Tech verified customer concern. Front right roller does not spin freely. Tech verified correct components received in good condition. Tech installed replacement rollers, tensioner and drive belt, reassembled unit and performed test cycle. Unit is functioning properly within manufacturer specifications."
We serviced a
WHIRLPOOL DRYER
Model WED49STBW1
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
05/19/2025
"Thermostat and thermal fuse are shorted out, removed and replaced components, tested unit, working and heating well now. Advised customer of situation and survey."
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Manitou Springs, Colorado 80829
Carlos
Job Details:
05/19/2025
"Installed capacitor, ran calibration ran cycle runs all ok"
We serviced a
WHIRLPOOL DRYER
Model WED6150PB0
Near Albuquerque, New Mexico 87109
Jason
Job Details:
05/19/2025
Installed parts unit checks ok. did also find that venting is restricted. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Albuquerque, New Mexico 87112
Jason
Job Details:
05/19/2025
checked unit found drain pump wire broken. installed harness. ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ18
Near Albuquerque, New Mexico 87108
Jason
Job Details:
05/19/2025
Checked unit spoke to cx about loading. they will try loading unit differently to see if that helps resolve issue. temps check ok for conditions at this time. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Sisters, Oregon 97759
Richard
Job Details:
05/19/2025
Installed new sump assembly cycle tested unit all tested fine & no leaks at time of repair..
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Rio Rancho, New Mexico 87144
Antonio
Job Details:
05/19/2025
"cx complaniy - washer not completing -used all parts that were ship ti cx home,unit is working properly - survey mentioned"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, New Mexico 87112
Jason
Job Details:
05/19/2025
Checked unit found lid latch not locking installed lid latch. ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
WOLF DOUBLE WALL OVEN
Model DO3050PM/S/P
Near Colorado Springs, Colorado 80908
Charles
Job Details:
05/19/2025
Replaced both temp sensors.
We serviced a
CAFE REFRIGERATOR
Model CVE28DP4NBW2
Near Elbert, Colorado 80106
Charles
Job Details:
05/19/2025
"Freezer at 3, customer had freezer empty, set -5, condenser coils dirty, offered to clean, customer will clean. Service fee $199.95"
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB8600QLAA
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
05/19/2025
"Checked water pressure, adjusted filter case assy hass passed"
We serviced a
SAMSUNG MICROWAVE
Model ME16A4021AS/A2
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
05/19/2025
Replaced door all checks ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB8600QLAA
Near Fountain, Colorado 80817
Brandon
Job Details:
05/19/2025
"Eal was coming from filter case assy, replaced filter and tested operation hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23HCEDBSR/AA
Near Colorado Springs, Colorado 80907
Brandon
Job Details:
05/19/2025
"Error 39c , ice maker frozen, replaced ice maker and cycled all checks ok"
We serviced a
SAMSUNG RANGE
Model NSI6DG9500MTAA
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
05/19/2025
Replace fan motor assy. Test op. All okay.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5101SG/AA
Near Colorado Springs, Colorado 80905
Brandon
Job Details:
05/19/2025
"Intermittent cooling for 3 days then unit stayed cooling for 2 days, checked for restrictions with compressor off pressures equalized, possible internal leak or possibly pcb issue, no visibles leak from UV die on evap or on any connection, revacuated system and recharged unit 72g, hass passed"
We serviced a
SAMSUNG MICROWAVE
Model ME16A4021AS/AA
Near Colorado Springs, Colorado 80927
Mathew
Job Details:
05/19/2025
"Found bad control board. Install new control, turn on breaker. Test op three times with cup of water, unit working as expected. All okay."
We serviced a
SAMSUNG RANGE
Model NE63A6511SS/AA
Near Colorado Springs, Colorado 80923
Mathew
Job Details:
05/19/2025
Found regulators stuck. Replaced all regulators per service bulletin. Test op all okay.
We serviced a
DACOR WALL OVEN
Model RO230S
Near Larkspur, Colorado 80118
Charles
Job Details:
05/19/2025
"Upper oven no bake, element homed good, burnt relay, need relay board, part is no longer available. Left voicemail with customer that part unavailable."
We serviced a
ZEPHYR WINE COOLER
Model PRW24C02BPG
Near Colorado Springs, Colorado 80921
Charles
Job Details:
05/19/2025
"Unit not cooling, compressor running, no frost pattern, corrosion in drain pan from evaporator leak, sealed system issue, needs compressor and evaporator. Service fee $159.95 paid autho 933JFJ"
We serviced a
BOSCH DISHWASHER
Model SHPM65Z56N/01
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
05/19/2025
Replaced broken door opener and worn latch. All operations now checks ok. RKCustomer paid balance 220.23 Auth 3X43U3
We serviced a
LG REFRIGERATOR
Model LFXC24726S.ASTCNA0
Near Monument, Colorado 80132
Ryan
Job Details:
05/19/2025
Found low side running in a vacuum.Contacted LG tech support and ran through all checks to verify leak in sealed system.Isolated yoder loop and pressurized with nitrogren .Yoder loop not holding pressure and explained to customer unit is not repairable. RK
We serviced a
LG FREEZER
Model LSXS26366D/11
Near Colorado Springs, Colorado 80918
Ralph
Job Details:
05/19/2025
installed parts andunit checked okayu
We serviced a
LG WASHER
Model F3S1CWKBTV.ASSEEUS
Near Pueblo, Colorado 81003
Domingo
Job Details:
05/19/2025
Replace the rubber seal test it and no leaks it test it good
We serviced a
LG FREEZER
Model LRDCS2603S.ASTCNA0
Near Colorado Springs, Colorado 80911
David
Job Details:
05/19/2025
"Repaired leak at inlet of dryer. Pressured for leaks, none, evacuated, charged system,unit is starting to cool down."
We serviced a
LG WASHER
Model WT7005CW.ABWETUS
Near Colorado Springs, Colorado 80924
Ryan
Job Details:
05/19/2025
Removed and replaced lid.Tested operation OK. RK
We serviced a
KITCHENAID COMBINATION OVEN
Model KEMS309BSS01
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
05/19/2025
"Checked unit, found the loud noise coming from the turntable motor. Replaced turntable motor and noise isnt loud. Turntable is turning properly. Unit is operating as designed.Service Fee-$139.95Labor-$229.95Turntable Motor-$105.10Supplies-$14.50Tax-$8.62Total-$498.12$498.12 CC Auth# H3J3R91 year warranty on partNo return on part"
We serviced a
GE DISHWASHER
Model PDT755SYV1FS
Near Grand Junction, Colorado 81506
Sean
Job Details:
05/19/2025
Customer signed disclaimer Checked the unit MN SN POP Unplugged the unit and pulled it out Unhooked the springs on the door unhooked the power to the door and removed the door. Disassembled the door and removed the inside panel. Transferred the door content to the new inside door panel.Secured inside panel to the door panel and reassembled the unit. Hooked door back on put unit in place and leveled the unit. Tested unit for any leeks. The unit tested good.Thank you for letting me do your service today.If you are satisfied with the results of the service I performed than please share your experience with others and leave a review.Thank you .
We serviced a
GE WASHER-DRYER COM
Model GUV27ESSM1WW
Near Avon, Colorado 81620
Erik
Job Details:
05/19/2025
CALL GE TAG: EXTENSIVE REAR BEARING / PANEL/ CASE DAMAGE - REAR PANEL AND DRYER PLATFORM ARE NOT AVAILABLE FOR REPLACEMENT PARTS* see quick pics (sent to GE)CASE# 16740445DEALER SHOULD SCRAP AND CREDIT WILL BE APPLIED FOR PRODUCTJOB COMPLETE
We serviced a
GE MICROWAVE OVEN
Model JVM3162RJ6SS
Near Eagle, Colorado 81631
Erik
Job Details:
05/19/2025
SA to correct install (rear needs to drop 1/4' to level unit) door 'flies open' when door released* see quickpicsunit NOT level (listing forward 1/4 - 1/2 ')JOB COMPLETE
We serviced a
GE REFRIGERATOR
Model PVD28BYNGFS
Near Colorado Springs, Colorado 80916
Ralph
Job Details:
05/19/2025
replaced list4d parts and unit checked okay
We serviced a
GE DRYER
Model GTD48EASW0WB
Near Grand Junction, Colorado 81503
Sean
Job Details:
05/19/2025
Customer signed disclaimer Checked the unit MN SN POP Opened package goodUnplugged the unit and removed the control panel and top panel. Removed the door panel. Removed the drum.Removed the thermostats and thermistors and installed the new ones. Reassembled the unit and restored the power.Tested the unit starts and heats up as designed by factory. if you appreciate the service I provided you with today Than please go online and fill out a technician survey and let other people know about your experience.
We serviced a
FRIGIDAIRE RANGE
Model GCFI3060BFB
Near Pueblo West, Colorado 81007
Domingo
Job Details:
05/19/2025
Call tech line File number 1003113510 they told me pots can not pass over the white line and it will shuts off. I put a smaller pot and make sure handle didnt cross the line and everything work this is on a tech tip number CKTT2429
We serviced a
SAMSUNG WASHER
Model WF45K6500AV/A2
Near Fountain, Colorado 80817
Brandon
Job Details:
05/19/2025
"Error 3c2, over current from motor, recommend invertor replacement and motor, motor would be covered under 10 year warranty, parts $349.40, labor 209.95, svf $139.95, mps $14.50, tax $28.65, svf paid $139.95 CC Auth# CA39XY, if moving forward would need motor ordered from Samsung"
We serviced a
FRIGIDAIRE WASHER
Model FAFW3511KW0
Near Colorado Springs, Colorado 80908
Dvante
Job Details:
05/19/2025
"Replaced door striker. Tested unit, door is locking now. Unit is operating as designed."
We serviced a
SAMSUNG MICROWAVE
Model ME11A7710DG/AA
Near Pueblo West, Colorado 81007
Domingo
Job Details:
05/19/2025
No body was home called csr she call them as well left them vm
We serviced a
MAYTAG DRYER
Model MED7230HW
Near Fountain, Colorado 80817
Brandon
Job Details:
05/19/2025
"Venting issue now, error f2e2, dryer works without vent connected, with vent connected unit gives error"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Albuquerque, New Mexico 87109
Larry
Job Details:
05/19/2025
CX conplaint - Stopped working midcycle - Inspeted unit and found the drain ppump harness came toole - Secured harness and tested good - Unit is good to go - Survey mentioned
We serviced a
MIDEA REFRIGERATOR
Model MRQ22D7AST
Near Pueblo, Colorado 81004
Domingo
Job Details:
05/19/2025
Replaced door with door seal test it and it test it good
We serviced a
PROFILE REFRIGERATOR
Model PFE28PYNFFS
Near Vail, Colorado 81657
Erik
Job Details:
05/19/2025
install/ test: PASS* see quick picstemps - GOODice/ water -GOODhot water - GOODJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Colorado Springs, Colorado 80916
David
Job Details:
05/19/2025
"Installed ordered parts, ran calibration and diagnostic cycles, and .lid locking as expected."
We serviced a
WHIRLPOOL WASHER
Model CAE2779JQ0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
05/19/2025
"Drain hose was improperly set, adjusted properly, ran cycle drained ok, no leaks found. Cx paid SC $189.95 CK Auth# 43NJ3R"
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Ashland, Oregon 97520
Jeff
Job Details:
05/16/2025
Hot water valve was partially closed turned all the way on and reset machine ran through full quick wash and went all the way thru. No errors
We serviced a
KITCHENAID RANGE
Model KSDB900ESS8
Near Bend, Oregon 97702
Levi
Job Details:
05/16/2025
"Replaced valve, burner and burner assembly tested and all checks okay"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Rogue River, Oregon 97537
Thomas
Job Details:
05/16/2025
Replaced parts listed. Door ajar alarm still goes off but LEDs turn off almost immediately after silencing the alarm. Customer okay with that
We serviced a
MAYTAG WASHER
Model MVW5035MW2
Near Ashland, Oregon 97520
Jeff
Job Details:
05/16/2025
Installed parts but found it's a drain issue at the wall. Tested machine no leaks found
We serviced a
WHIRLPOOL WALL OVEN
Model WOES3030LS01
Near Terrebonne, Oregon 97760
Richard
Job Details:
05/16/2025
Tested unit with tech support change language from French to English cycle tested unit in preheat all tested fine at this time
We serviced a
KITCHENAID RANGE
Model KFDD500ESS12
Near Manitou Springs, Colorado 80829
Jerimiah
Job Details:
05/16/2025
"Regulator supporting 12psi was installed on tank, adjustments to each burner was now possible and completed. Unit check ok. Cust will give very good review."
We serviced a
WHIRLPOOL RANGE
Model WFC315S0JB3
Near Colorado Springs, Colorado 80910
David
Job Details:
05/16/2025
Replaced burners and top wire harness. Tested and is not tripping breaker.
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
05/16/2025
Installed drain hose all ok
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
05/16/2025
Installed control board and UI runs all ok
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
05/16/2025
"Control pressure sensor relay is shorted out, removed and replaced control, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Colorado Springs, Colorado 80907
Carlos
Job Details:
05/16/2025
Installed capacitor and actuator runs all ok
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
05/16/2025
"F7E6 motor circuit error code upon arrival, capacitor came out of holder and broke lower harness wire, removed and replaced capacitor and lower harness, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVW5035MW2
Near Peyton, Colorado 80831
Aaron
Job Details:
05/16/2025
"Break in lower harness, capacitor is shorted out, removed and replaced components, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS2
Near Monument, Colorado 80132
Ryan
Job Details:
05/16/2025
Removed and replace track and stops. Reinstalled top rack and tested function ok.Ran diagnostic cycle and checked unit for proper operation and all checks ok. RK
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS2
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
05/16/2025
"Installed board, bake and broil elements ran until 500 degrees for 20 minutes runs all ok"
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
05/16/2025
"Installed motor and blower runs all ok. Property management needs to replace hose, it is crushed"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Leadville, Colorado 80461
Antonio
Job Details:
05/16/2025
Unit needs to be unplugged for 24 hrs for it to work properly. cx has not done so yet
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Grand Junction, Colorado 81505
Josh
Job Details:
05/16/2025
"Customer signed disclaimer. Verified MN SN POP. Technician confirmed correct components received in good condition. Technician installed replacement lower agitator Assy and selector Assy. Tech performed test cycle, observing productive function of all cycles. Unit is functioning properly within manufacturer specifications."
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Grand Junction, Colorado 81505
Josh
Job Details:
05/16/2025
"Customer signed disclaimer. Verified MN SN. Customer states that unit displays check vent error. Technician unable to duplicate customer concern. Tech notes that adequate exhaust flow is present at exterior, noting difficulty trimming and properly reinstalling oblong exhaust vent. Unit is functioning properly within manufacturer specifications."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ16
Near Peyton, Colorado 80831
Aaron
Job Details:
05/16/2025
"Dripping from water filter connection, removed and replaced water reservoir assembly, unit is not leaking with water filter bypass, leaks with filter, recommend using factory recommended filters. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHZ0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
05/16/2025
"Upper rack adjusters assembly is causing rack to not properly engage water inlet, removed and replaced adjuster assembly, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
MAYTAG WASHER
Model MVWB765FW4
Near Pueblo, Colorado 81005
James
Job Details:
05/16/2025
Installed ordered parts tested ops all ckok
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, Colorado 80920
Mauricio
Job Details:
05/16/2025
Swapped out defective heating element unit is heating up unit tested to spec
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB05
Near Pueblo, Colorado 81005
Domingo
Job Details:
05/16/2025
Replaced filter housing test it no leaks its good to go
We serviced a
MAYTAG DRYER
Model MEDB835DC4
Near Peyton, Colorado 80831
Aaron
Job Details:
05/16/2025
"Rollers and idler have worn from use, removed and replaced components, cleared unit of lint, tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
AMANA DISHWASHER
Model ADB1400AMW1
Near Edgewood, New Mexico 87015
Jason
Job Details:
05/16/2025
Installed part. ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Tijeras, New Mexico 87059
Jason
Job Details:
05/16/2025
Checked unit found drain pump not opperating installed pump. ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Albuquerque, New Mexico 87123
Jason
Job Details:
05/16/2025
Checked unit found toe plate was bent and catching on door. adjusted toe plate fitment unit checks ok. spoke to cx about review
We serviced a
MAYTAG DRYER
Model MGDP575GW0
Near Los Ranchos de Albuquerque, New Mexico 87107
Larry
Job Details:
05/16/2025
CX complaint - Unit stops when being used - Inspected unit and found moisture sensor open - Replaced with TS and tested good - Unit is good to go; used 1 WPW10298258 (Sensor Harness) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Albuquerque, New Mexico 87109
Jason
Job Details:
05/16/2025
Installed parts checked auger function auger checks ok unit checks ok. spoke to cx about review
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Albuquerque, New Mexico 87120
Larry
Job Details:
05/16/2025
CX complaint - The entire back panel is loose - Called techline (SR7741589934) - The lefft side of the panel does pushes back farther than the right side - Per techline issue is cosmetic and won't be covered by warranty
We serviced a
MAYTAG DISHWASHER
Model MDB7601AWB
Near Central Point, Oregon 97502
Jeff
Job Details:
05/16/2025
Found bad switch for door latch also motor is siezed and no controls work but the start button called tech line file 7741586909 parts nla not repairable also called third party and they couldn't locate parts sr 7741499083 good to bill out
We serviced a
MAYTAG WASHER
Model MVWB765FW2
Near Los Lunas, New Mexico 87031
Larry
Job Details:
05/16/2025
Installed gearcase and tested good - Unit s good to go
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS02
Near Albuquerque, New Mexico 87112
Jason
Job Details:
05/16/2025
Installed fan and fan blade unit opperation checks ok. spoke to cx about review
We serviced a
MIELE RANGE HOOD
Model DA6690D
Near Colorado Springs, Colorado 80918
Charles
Job Details:
05/16/2025
"Replaced light power supply 8165140, Service fee $189.95, Labor $209.95MPS $14.50, Part $221.30Tax $18.50, Total $653.85, paid autho VYCX94; used 1 8165140 (Power supply) from stock"
We serviced a
SUBZERO REFRIGERATOR
Model BI-42UFD/S/TH
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
05/16/2025
"unit had a bad relay for the firdge compressor on the main board, replaced part and unit ch3ecked okay...autho no. F993ML"
We serviced a
SAMSUNG DRYER
Model DVE50BG8300VA3
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
05/16/2025
"Unit in garage. Found dryer hooked up to water, no signs of leak. Ran thru with tech line, agent put under review. Cx will hear back directly."
We serviced a
SAMSUNG WASHER
Model WF50BG8300AVUS
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
05/16/2025
"Unit in garage. Hooked up to drain extension running into house. Cx provided video of machine leaking down fill hoses. Ran machine multiple times, no leaks. Ran thru with tech line, agent put under review. Cx will hear back directly."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5100SRAA
Near Yoder, Colorado 80864
Mathew
Job Details:
05/16/2025
Found evaporator fan not operating. Replace evaporator fan assy. Test op all okay.
We serviced a
SAMSUNG REFRIGERATOR
Model RF23M8070SR/AA
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
05/16/2025
"Ice maker frozen, replaced parts and cycled, svf and labor paid $344.40 CC Auth# HMH93N"
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA
Near Colorado Springs, Colorado 80951
Brandon
Job Details:
05/16/2025
"No errors, unit didn't drain, cycle interrupted possibly, installed high loop for drain hose and tested operation hass passed"
We serviced a
SAMSUNG RANGE
Model NSE6DG8300SRAA
Near Colorado Springs, Colorado 80917
Mathew
Job Details:
05/16/2025
Replace broil element. Burn off. Test op all okay.
We serviced a
SAMSUNG DRYER
Model DVE45T6000W/A3
Near Colorado Springs, Colorado 80927
Brandon
Job Details:
05/16/2025
Bad TCO replaced heater assy and tested op hass passed
We serviced a
SAMSUNG RANGE
Model NSI6DG9550SRAA
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
05/16/2025
"Replaced oven control PCB and checked all connections and ribbons, tested operation all checks ok"