We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Carbondale, CO 81623
James R
Job Details: 02/21/2023
F5E3 error code unlock failure. Put thru auto diagnostics test. 12 Advanced thru cycle no codes when done. Complaints from customer are normal/regular cycle would randomly stop at different times and not resume cycle. called tech line. want customer to monitor operation of unit to seer if any other error codes come up. They do not recommend any replacement of parts at this time. SR# 7735782949
We serviced a
KITCHENAID RANGE
Model KFGG500ESS3
Near Santa Fe, NM 87507
Jason
Job Details: 02/21/2023
Checked unit found spark board plug not seated seated connection
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Colorado Springs, CO 80908
Kris
Job Details: 02/21/2023
ran test op replaced im ran test op unit filled and harvested all ok cx is aware of 5 star survey.
We serviced a
KITCHENAID REFRIGERATOR
Model KBFN502ESS02
Near Dillon, CO 80435
Antonio
Job Details: 02/21/2023
installed new evap fan found unit is up for review found leak in back wall of unit none repairable leaking freon SR#773583317
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS1
Near Dillon, CO 80435
Antonio
Job Details: 02/21/2023
installed new door seal unit tested good
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Glenwood Springs, CO 81601
James R
Job Details: 02/21/2023
"Installed pad on base asy.replaced Base,motor and wheel. Put some wet cloths in unit and run. Sounds good. Please fill out tech customer satisfaction survey. Thank You."
We serviced a
THERMADOR RANGE - GAS
Model RDDS30VQB
Near Colorado Springs, CO 80921
Jessie
Job Details: 02/21/2023
"lf burner is clicking after ignition. cleaned igniter, if customer calls back will need to replace ignitors and module.4x ignitor#001893241x module#nla- will need to monitor"
We serviced a
SUBZERO REFRIGERATOR
Model BI-36UFD/S/PH
Near Colorado Springs, CO 80906
Ralph
Job Details: 02/21/2023
"replaced ice mkr, unit checked okay"
We serviced a
FISHERPAYKEL WALL OVEN
Model DS302-SS
Near Colorado Springs, CO 80906
Ralph
Job Details: 02/21/2023
"installed part, unit still takes a while to heat up, but cust okay'd the repair"
We serviced a
WHIRLPOOL DRYER
Model WED7000DW1
Near Colorado Springs, CO 80917
Glenn
Job Details: 02/21/2023
"Customer indicated that unit has not tripped breaker lately. Did find Left Rear Support roller binding. Cleared hair and debris from Support Roller Assy. Checked power chord at junction block > OK, Suggest possible bad Breaker if unit starts tripping breaker again. Also suggest that Electrician verify 240VAC outlet is isolated for Dryer use only. All OPS Test:OK"
We serviced a
MIELE COFFEE MACHINE
Model CVA6805
Near Monument, CO 80132
Jessie
Job Details: 02/21/2023
"- replaced grinder and ring, customer still put very oily beans in coffee unit. we can not warranty a grinder that customer uses oily beans in. - test op, all ok"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Monument, CO 80132
Jessie
Job Details: 02/21/2023
"- replaced left door, test op, all ok"
We serviced a
BOSCH DISHWASHER
Model SHPM78Z55N/20
Near Woodland Park, CO 80863
Ken
Job Details: 02/21/2023
Cust was having drying issues. Tested dw and everything is running g correctly. Called and spoke to Bosch. They recommended adding extra drying time through the setting. Added 30 mins for customer and recommended using rinse aid. Unit is working properly
We serviced a
BOSCH RANGE
Model HGI8056UC
Near Woodland Park, CO 80863
Ken
Job Details: 02/21/2023
Oven was not lighting. Pulled out and checked igniter and it is good. Moved back in place and tested again. Everything is working properly. Tested oven several times and is lighting everytime
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ16
Near Colorado Springs, CO 80922
Brandon
Job Details: 02/21/2023
Cx got fridge replaced
We serviced a
WHIRLPOOL WALLOVEN
Model WOS31ES0JS01
Near Rio Rancho, NM 87124
Joseph
Job Details: 02/21/2023
installed parts listed. unit tested good. unit is good to go.
We serviced a
WHIRLPOOL COOKTOP
Model KECD807XSS00
Near Rio Rancho, NM 87144
Joseph
Job Details: 02/21/2023
fan not turning on. inspect unit. found that the plug was not plugged in all the way and was really easy to pull out. plugged in the plug all the way. unit is working great. blower fan is working great. unit is good to go. charged customer $129.95 for service charge fee.Auth code:4393X4
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Rio Rancho, NM 87144
Joseph
Job Details: 02/21/2023
installed parts listed. unit tested good. unit is good to go. highly recomended customer to have an electrician come out to make sure the breaker is good as well since the breaker was tripped 4 to 5 times when using the washer before the first visit.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM02
Near Albuquerque, NM 87110
Larry
Job Details: 02/21/2023
Installed parts listed anqd tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model MVWC565FW2
Near Albuquerque, NM 87110
Larry
Job Details: 02/21/2023
Installed parts listed and tested good - Unit is good to go; used 1 W11307244 (Latch) from stock
We serviced a
WHIRLPOOL RANGE
Model WFG515S0ES1
Near Albuquerque, NM 87105
Larry
Job Details: 02/21/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
GE WALLOVEN
Model CTD90FP2N1S1
Near Peyton, CO 80831
Aaron
Job Details: 02/21/2023
"Interface is working at time of inspection, upper and lower oven temps are good, door lock is not engaging in steam clean mode, needs lock and control. Rest of unit is in good condition. Control Wb56x40097 $898.54Lock motor wb10x28391$92.50Total parts $991.04Tax $81.27Supplies $14.50Hc $129.95Labor 2 people =189.95?2=379.90Total job $1,596.6630 day estimateNo return on parts129.95 hc auth #93ATH9"
We serviced a
BOSCH DISHWASHER
Model SHPM78Z55N/20
Near Peyton, CO 80831
Glenn
Job Details: 02/21/2023
Install New Wheels on lower rack. Suggest obtaining rinse product that is blue liquid. (Not Clear) to provide better drying. Also suggest not waiting over night to open unit to avoid moisture accumulation back on dishes.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Peyton, CO 80831
Glenn
Job Details: 02/21/2023
"Install New Gearcase, Shifter & Belt. All OPS Test:OK"
We serviced a
JENNAIR WALL OVEN
Model WOC75EC0HS20
Near Colorado Springs, CO 80906
Jerimiah
Job Details: 02/21/2023
Unit losing time and resetting day by itself. Connecting unit to WiFi. Told Cust to keep track of unit but should experience any more issues. Unit check ok. Otherwise unit will need console replacement. Disclosed survey to cust FCC.Notes: console ui W11616683
We serviced a
SAMSUNG OVEN
Model NE63A6311SS/AA
Near Colorado Springs, CO 80910
Jerimiah
Job Details: 02/21/2023
"Cooktop heats but no cooktop hot light, control board with display doesnt light and not responsive. Replaced controller, no help, found floating neutral at socket. Needs electrician. Closing call."
We serviced a
WHIRLPOOL REFRIGERATOR-SID
Model WRS321SDHZ05
Near Colorado Springs, CO 80907
Ralph
Job Details: 02/21/2023
"upon arrival found ice mkr stuck in a harvest, pressed test button and ice mkr found home position, retested and ice mkr cycled and filled, cust to monitor."
We serviced a
SAMSUNG WASHER
Model WF45T6000AV/A5
Near Colorado Springs, CO 80918
Jeremy
Job Details: 02/21/2023
Installed all new parts. Ran HASS and passed. Double checked for leaks. Unit is working to specification. Asked CX to complete survey.
We serviced a
KITCHENAID WALL OVEN ELECTR
Model KEBS278DSS11
Near Monument, CO 80132
Jessie
Job Details: 02/21/2023
#NAME?
We serviced a
KITCHENAID DISHWASHER
Model KDTE104ESS2
Near Colorado Springs, CO 80920
Glenn
Job Details: 02/20/2023
"burning/melting smell before drying cycle. water in unit end of use. Error 8-2 - Drain Motor. Inspected Unit and ran diag. cycle. No smells or burning wries/plastic. Not able to duplicate problem reported. All OPS Test:OK at this time. Paid SC fee of $129.95, Autho#RNC393"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Loma, CO 81524
James R
Job Details: 02/20/2023
Customer indicates cloths have dry spots. Not cleaning well. Put unit into diagnostics. Has no error codes. Run auto test. No issues. Sounds normal. Agitate and spin. Put in a load of towels. Deep water warm temp setting. Unit cycles back and forth hot to cold for warm water. ok. Unit filled about half full of water on deep water setting. Normal. Towels are all wet.Called tech line to confirm findings. SR# 7735768732 Customer should use deep water setting for all cycles. Get more water in. Only fill unit half to 3/4 full of cloths. Once wet will be at a normal level.Normal setting will not fill up as much. Unit is operating as should. Not coverd under warranty. Customer was told there would be no charge for the call by whirlpool.
We serviced a
MAYTAG WASHER
Model MVW6230HW1
Near Colorado Springs, CO 80908
Aaron
Job Details: 02/20/2023
"Fault codes at time of inspection F7E6 motor,F0E3 overload, F5E4 door not opened, Ran unit through diagnostics, very little rotation during agitation and noisy gears in spin, straining motor and wearing drive belt. Needs transmission and drive pulleyTransmission w11449840 $304.86Drive pulley w10721967 $74.70Total parts $379.56Tax $31.12Hc $129.95Supplies $14.50Labor 2 hrs 169.95 ?2=339.90Total job $895.03Auth 129.95 hc #94YE3L30 day estimateNo return on parts"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAHZ0
Near Albuquerque, NM 87121
Joseph
Job Details: 02/20/2023
installed parts listed. test unit. unit tested good. unit is good to go.
We serviced a
WHIRLPOOL FREEZER
Model WZF34X20DW04
Near Rio Rancho, NM 87144
Joseph
Job Details: 02/20/2023
knocking and rattling noise when compressor is running. inspect unit. found the condensor line was against the cabinet. i did move the line away from the cabinet. also let customer know it could be the refrigerant flowing and that it is a common and normal sound that you can hear and they can find it in their owners manual. no further issues. unit is workin great.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHW4
Near Colorado Springs, CO 80918
Aaron
Job Details: 02/20/2023
"Replaced assembly and tested unit, working well and no leaks. Advised customer of survey Auth 169.95 #A3R9MW"
We serviced a
WHIRLPOOL DRYER
Model WED8127LW1
Near Rio Rancho, NM 87144
Joseph
Job Details: 02/20/2023
does not have proper voltage to the unit. unable to test or diagnose unit .
We serviced a
MAYTAG WASHER
Model MVWB835DW3
Near Colorado Springs, CO 80918
Aaron
Job Details: 02/20/2023
"Replaced controls and ran unit through diagnostics, working well now. Advised of 5 star survey"
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5201SG/AA
Near Colorado Springs, CO 80911
Jeremy
Job Details: 02/20/2023
Installed all new parts. Ran HASS and passed. Im seems to be working correctly. Asked CX to complete survey.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, CO 80906
Ralph
Job Details: 02/20/2023
installed listed parts and unit checked okay
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Pueblo West, CO 81007
James
Job Details: 02/20/2023
Installed ordered parts all ops test good ice maker cycled as designed.
We serviced a
COVE DISHWASHER
Model DW2450WS
Near Colorado Springs, CO 80906
Ralph
Job Details: 02/20/2023
installed part and unit checked okay....amy 30 mins on this replacement please
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ12
Near Pueblo West, CO 81007
James
Job Details: 02/20/2023
Found loose wire at ui causing it to be unresponsive. Secured and tested. Ops ckok
We serviced a
DACOR REFRIGERATOR
Model DRR36980RAP
Near Colorado Springs, CO 80906
Ralph
Job Details: 02/20/2023
"replaced cust water filter, unit checked okay...cust paid total, autho no. 9AXP99"
We serviced a
GENERAL ELECTRIC REFRIGERATOR - S
Model GFE28GYNISS
Near Colorado Springs, CO 80905
Ralph
Job Details: 02/20/2023
"door handle was very loose, had to remove then tigh5tened down the door handle bolts, then resecured the door handle and unit checked okay"
We serviced a
MIELE DRYER
Model TXD160WP
Near Woodland Park, CO 80863
Jessie
Job Details: 02/20/2023
"- replaced compressor base, unit pulling 5.7 amps and feel heat all ok"
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JVM3160RF8SS
Near Colorado Springs, CO 80923
Aaron
Job Details: 02/20/2023
"Unit's blower was never rotated, does not have a true vent, unit overheating due to heat being unable to escape, corrected and pushing air well now. Unit is heating well at time of inspection. Advised of survey"
We serviced a
GENERAL ELECTRIC RANGE - ELECTRIC
Model JB258DM3WW
Near Colorado Springs, CO 80915
Ken
Job Details: 02/20/2023
Installed glass
We serviced a
MIDEA DISHWASHER
Model MDT24H3AST
Near Fountain, CO 80817
Ken
Job Details: 02/20/2023
Cleared obstruction from drain line. Dw is operating properly
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031USAA
Near Pueblo West, CO 81007
Brandon
Job Details: 02/20/2023
"Removed dishwasher from underneath cabinet and checked for visible signs of leaking found water stains on leak tray but can not tell where leak is coming from, ran cycle for 30 min but found no leaking anywhere, water stains are above wash motor but it isn't leaking currently, recommend replacing sump assy DD82-01376B $388.30. cx would like to wait on repair Collected svf $129.95 Auth# 49P44ALabor $189.85Parts $388.30Tax $31.88Mps $14.50Remaining total $625.13"
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS0
Near Santa Fe, NM 87508
Jason
Job Details: 02/20/2023
installed heater unit checks ok
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD708MSS00
Near Santa Fe, NM 87506
Jason
Job Details: 02/20/2023
Checked unit found door seals werent sealing all the way reformed gaskets unit checks ok
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Peyton, CO 80831
Glenn
Job Details: 02/20/2023
"Install New Main PCB, All OPS Test:OK"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23M8070SR/AA
Near Colorado Springs, CO 80924
Jonny
Job Details: 02/20/2023
"Loose connection, problem solved, hass passed."
We serviced a
SAMSUNG WASHER
Model WF45R6100AC/US
Near Colorado Springs, CO 80922
Jonny
Job Details: 02/20/2023
"7005392822 exchange, noticed bracket was missing a piece, called techline did visual support"
We serviced a
ASKO WASHER
Model W6021
Near Colorado Springs, CO 80907
Jessie
Job Details: 02/20/2023
"- unit start switch is good, found relay not able to send correct voltage to switch, relay blown on bd, needs new bdbd#8065839 NLAsc $149.95$14.50labor $249.95- BEING PART IS NLA CUSTOMER HAS BEEN PROVIDED PART NUMBER AND WILL TRY TO GET BACK TO US.30 DAYS SC"
We serviced a
SAMSUNG DRYER - ELECTRIC
Model DVE50R5200W/A3
Near Pueblo, CO 81004
Brandon
Job Details: 02/20/2023
"Replaced parts tested op all ok hass passed, educated cx on operation"
We serviced a
BOSCH DISHWASHER
Model SHE45M02UC/50
Near Colorado Springs, CO 80920
Jeremy
Job Details: 02/20/2023
CX is deciding on buying a new dishwasher. CX may contact if they decide to do repair.
We serviced a
SAMSUNG WASHER
Model WF50BG8300AVUS
Near Monument, CO 80132
Jeremy
Job Details: 02/20/2023
Installed all new parts. Test ran unit. Vacant house so no CX's present for signature. Double checked for leaks. Ran HASS and passed.
We serviced a
SAMSUNG WASHER
Model WA50R5200AW/US
Near Pueblo, CO 81004
Brandon
Job Details: 02/20/2023
Replaced parts tested op all ok hass passed told cx about survey
We serviced a
MAYTAG WASHER
Model MHW6630HW0
Near Albuquerque, NM 87105
Larry
Job Details: 02/20/2023
Installed drawer and tested good - Unit is good to go
We serviced a
SAMSUNG REFRIGERATOR
Model RF30HBEDBSR/AA
Near Pueblo, CO 81005
Brandon
Job Details: 02/20/2023
Replaced parts reset ice maker it cycled has not compatible
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Albuquerque, NM 87120
Larry
Job Details: 02/20/2023
Installed heater and tested good - unit is good to go
We serviced a
THERMADOR COOKTOP
Model GCV36G
Near Colorado Springs, CO 80917
Glenn
Job Details: 02/20/2023
Unit is over 30 years old.Burners not igniting. Bad Spark Module.Parts NLA (Discontinued)
We serviced a
MAYTAG DRYER
Model MED6230HW2
Near Grand Junction, CO 81504
James R
Job Details: 02/20/2023
Door seal is fraid. Coming apart. W11596131 called tech line. Panel of front of dryer is in good condition. Hinges dont appear to be bent. But hinges pull door really tight to front panel and flatten seal. Recommend replacing hinges W11551301 #7735775433 Customer to pay $149.00 service call auth code RV4HJA Customer has coverage under a Allstate plan. She will contact them.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHV05
Near Florence, CO 81226
Kris
Job Details: 02/20/2023
installed compressor ran test op all ok unit is working to spec at this time. cx will monitor unit.
We serviced a
WHIRLPOOL WASHER
Model WFW6620HC2
Near Albuquerque, NM 87120
Larry
Job Details: 02/20/2023
CX complaint - F6E3 error - Inspected unit and found F6E3 Comms error - Unit needs UI and control - Cx doesn't want to bear the cost of repair - Collected $129.95-Auth-44P9KP
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Grand Junction, CO 81504
James R
Job Details: 02/20/2023
No heat. Removed rear panel. checked heat element ok. Looks good and not shorted. checked vent it is restricted. Customer needs to have it cleaned. Thermal open. Installed cutoff kit. 279816. Run unit. is heating. Op's good. Please fill out tech customer sarisfaction survey. Thank You.; used 1 279816 (Cutoff) from stock
We serviced a
WHIRLPOOL DISHWASHER - BUI
Model WDTA50SAKZ0
Near Colorado Springs, CO 80917
Glenn
Job Details: 02/20/2023
"Recvd Error F8E4Unit has since been unplugged.Reseat connections to PCB.Plugged in unit. All OPS Test:OK, No Errors."
We serviced a
BOSCH DISHWASHER
Model SHE3AR76UC/28
Near Colorado Springs, CO 80917
Glenn
Job Details: 02/20/2023
"soap dispenser door not working/ not enough water getting to unit. Unit did not fill to proper water level, while clothes washer was filling. Stopped cycle, and turned off washer. Started another DW cycle, and it did fill correctly. customer had indicated that dispenser door not opening, Re-seated Connections. and it did open during test. If problem returns, Suggest order new dispenser and Main PCB. All OPS Test:OK at this time."
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0AS03
Near Albuquerque, NM 87120
Larry
Job Details: 02/20/2023
CX complaint - F6E8 - Inspected unit and found comms error for the MW Mgr - Cx does not want to bear the cost of repair - Collected $129.95-Auth-R9FWR4
We serviced a
GENERAL ELECTRIC RANGE - ELECTRIC
Model JSS86SP5SS
Near Basalt, CO 81621
Erik
Job Details: 02/20/2023
connect to SmartHQ service:smartHQ service NOT availble for this unitdisassemble cooktop and rear panel and inspect comm and supply line to/from switch and UI to Relay board: J401 harness loose/seperated from board reconnect security strap - test: 400* - GOOD!call tech line: case# 09365568JOB COMPLETE!
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Pueblo, CO 81003
James
Job Details: 02/20/2023
Found loose wire at water valve. Secured and tested all ops test good.
We serviced a
SAMSUNG DRYER
Model DVE50R5400V/A3
Near Pueblo West, CO 81007
Brandon
Job Details: 02/20/2023
Replaced parts tested op all ok hass passed
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Colorado Springs, CO 80920
Kris
Job Details: 02/20/2023
installed switch ran test op all ok unit is workin g to spec.
We serviced a
GE REFRIGERATOR
Model PWE23KSKKSS
Near Colorado Springs, CO 80924
Kris
Job Details: 02/20/2023
installed fan. ran test op all ok cx will monkitor unit.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HFEDTSR/AA
Near Colorado Springs, CO 80920
Jonny
Job Details: 02/20/2023
"Installed parts, custy happy, not hass compatible"
We serviced a
WHIRLPOOL DRYER
Model WED5000DW2
Near Grand Junction, CO 81505
James R
Job Details: 02/20/2023
Removed rear panel. checked heat element it is bad. Replaced it 279838VP and cutoff thermal. 279816 customer had these parts. Also unit is squeaking. will install a repair kit. 4392065 Installed repair kit. Test run Op's is good. Please fill out tech customer satisfaction survey. Thank You.; used 1 4392065 (Dryer repair kit) from stock
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS2
Near Fruita, CO 81521
James R
Job Details: 02/20/2023
F2E1 error code shorted key pad. Replaced Control. Test op's Good. No one available to sign. Please fill out tech customer satisfaction survey. Thank You.
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JVM3162DJ3BB
Near Colorado Springs, CO 80904
Jim
Job Details: 02/20/2023
"replaced the magnetron assembly, test unit with a bottle of water, unit test ok"
We serviced a
GENERAL ELECTRIC DRYER - ELECTRIC
Model GFD65ESSN0WW
Near Colorado Springs, CO 80906
Jim
Job Details: 02/20/2023
"replaced the drum, ran unit on quick dry cycle unit test ok."
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDP665SYN3FS
Near Colorado Springs, CO 80906
Jim
Job Details: 02/20/2023
"replaced the drain hoses ran unit in 1 hour cycle, unit filled and washed put in drain mode unit drained and no leaks test ok"
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW
Near Colorado Springs, CO 80911
Ken
Job Details: 02/20/2023
Ran load on quick wash. Washer performed properly. Issues were possibly due to unbalanced loads. Tested springs and pump all OK. Advised customer that drain and spin is recommended by wp when clothes are left damp. Recalibrate discussed survey with customer ftc
We serviced a
GENERAL ELECTRIC DOUBLE WALL OVEN
Model JTD3000SN2SS
Near Colorado Springs, CO 80924
Aaron
Job Details: 02/20/2023
"Hardwired both upper and lower temp sensors per GE techline, preheated both ovens to 200f, heating well, no code on cooldown.Advised of survey"
We serviced a
GENERAL ELECTRIC DRYER - ELECTRIC
Model GTD65EBSJ4WS
Near Colorado Springs, CO 80916
Jim
Job Details: 02/20/2023
replaced the moisture sensor harness and the top bearing assembly unit test ok
We serviced a
GENERAL ELECTRIC DRYER - ELECTRIC
Model GTD33EASK0WW
Near Colorado Springs, CO 80909
Jim
Job Details: 02/20/2023
"found the start switch is inop replaced the start switch, unit test ok"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Pueblo West, CO 81007
Brandon
Job Details: 02/20/2023
Replaced parts reset ice maker it cycled hass passed
We serviced a
PROFILE MICROWAVE
Model JT965S0F3SS
Near Colorado Springs, CO 80923
Aaron
Job Details: 02/18/2023
"Microwave oven control board is not sending power to high voltage components or turntable, unit is mounted to lower walloven, but is accessible. Door switches are shorted as well. Control WB27T10491Switch ?2 WB24X829Switch WB24x830Control is no longer available 129.95 hc auth #T3PP44"
We serviced a
WHIRLPOOL WALLOVEN
Model WEG745H0FS0
Near Colorado Springs, CO 80922
Aaron
Job Details: 02/18/2023
"Control board is intermittently working, Front left board tab is stripped, console bottom tabs are stripped as well, unit does not have a backsplash. Rest of unit is in good condition. Control w10885069 $377.27Console assem w10728507 $328.72Clip?3 w10866583 $30.48?3= 91.44Total parts $797.43Tax $65.39Hc $129.95Labor $169.95Total job $1162.72Board only 377.27Tax $30.94Hc $129.95Labor$169.95Total job$708.1130 day estimateNo return on parts129.95 hc auth #43EEPMAdvised of 5 star survey"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HC2
Near Colorado Springs, CO 80904
Jim
Job Details: 02/18/2023
"replaced the suspension rods, ran unit in a drain and spin unit test ok TAS"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ00
Near Colorado Springs, CO 80903
Ralph
Job Details: 02/18/2023
replaced listed parts and unit checked okay
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404KPS0
Near Peyton, CO 80831
Aaron
Job Details: 02/18/2023
"Water inlet assembly is seeping water down side of tub, heater bushings dripping and getting into circulation motor, motor is weak from this happening overtime. Inlet assembly w11535094 $87.44Heater assembly w11537778 $97.06Circulation motor sump assem w11416362 $292.16Total parts $476.66Tax $39.09Hc $129.95Labor $169.95Total job $815.6530 day estimate No return on parts Auth 129.95 hc check #Y9K34M"
We serviced a
SAMSUNG DISHWASHER
Model DW80M2020US/AA 00
Near Colorado Springs, CO 80921
Glenn
Job Details: 02/18/2023
"pump running too much, indicator light onFound water inlet valve dripping during fill.DD82-01588A $204.28 , Tax $16.75, MPS $14.50, Labor $174.95.Declined Estimate, wants to buy new unit.Paid SC Fee of $129.95, Autho#39TT4P"
We serviced a
GE WASHER
Model WHDSR109J5WW
Near Pueblo, CO 81005
James
Job Details: 02/18/2023
Installed ordered parts all ops test good
We serviced a
SAMSUNG REFRIGERATOR
Model RF24FSEDBSR/AA 24
Near Peyton, CO 80831
Glenn
Job Details: 02/18/2023
"Unit started having ice room issue again as of Nov of 2021. Kit lasted 15 months.40E Error > Auger Fan Motor Error, Auger Motor Assy - DA97-12540K $326.66 , Tax $26.79 , Labor $174.95, MPS $14.50Customer Declined Estimate for Now, wants to contact Samsung first. Paid SC fee of $129.95 , Autho#44LM3U"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Colorado Springs, CO 80924
Jim
Job Details: 02/18/2023
"replaced the gearcase, slider, drain pump and spanner nut, ran unit in drain and spin , unit test ok, TAS"
We serviced a
BOSCH DISHWASHER
Model SHE53TF5UC/02
Near Colorado Springs, CO 80920
Jessie
Job Details: 02/18/2023
"- unit spring is broken,spring kit#12004119 $95.80tax $7.86sc $149.95$14.50labor $209.95total $478.06- found unit needs a safety recall kit installed, customer needs to reach out to bsh for this kit. advised not to use until kit is installed.30 days estimate"
We serviced a
MIELE COFFEE MACHINE
Model CVA6805
Near Colorado Springs, CO 80921
Jessie
Job Details: 02/18/2023
"- replaced bad front ceramic valve, test op, all ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Pueblo West, CO 81007
James
Job Details: 02/18/2023
Installed ordered parts all ops test good
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model PFE28KYNBFS
Near Peyton, CO 80831
Aaron
Job Details: 02/18/2023
"Replaced parts, fan has better push, unit needs time to cool back down, condenser cleaned as well, working well now.Advised of survey"
We serviced a
COVE DISHWASHER
Model DW2450
Near Colorado Springs, CO 80906
Ralph
Job Details: 02/17/2023
installed part and unit checked okay