We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Bend, Oregon 97702
Levi
Job Details:
09/03/2025
Tested dryer and all checks okay. Temps are perfect
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM11
Near Bend, Oregon 97702
Levi
Job Details:
09/03/2025
"Replace ice maker kit, tested, all checks okay and no leaks detected at time of service."
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCF72DKL05
Near Powell Butte, Oregon 97753
Richard
Job Details:
09/03/2025
Installed new door seal on RH refer door adjusted door all tested fine at this time
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
09/03/2025
Installed fuse runs all ok recommend cx have vents cleaned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ11
Near Colorado Springs, Colorado 80910
Carlos
Job Details:
09/03/2025
installed compressor charged with 2.3 oz of R600a. Cx will observe
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
09/03/2025
"Removed and replaced components, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
MAYTAG DRYER
Model MEDP575GW1
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
09/03/2025
"Checked unit, found paint peeling off the drum. Replaced the drum. No paint peeling. Unit is tumbling and operating as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3036RZ00
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
09/03/2025
"Evaporator cap tube line vibrating against metal plate when evaporator fan motor is on, corrected and tested , verified by customer. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DRYER
Model WGD8127LC4
Near Eagle, Colorado 81631
Antonio
Job Details:
09/03/2025
Found vent clogged at exterior side. Cleared clogge and then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPA01
Near Glenwood Springs, Colorado 81601
James R
Job Details:
09/03/2025
Customer signed disclaimer. Removed unit and replaced drain pump. While out ran a bit to check for a leak none. Put unit back in place and test run in service diagnostics unit is functioning as should. Turned unit on and let run thru a cycle. During normal operation the ice hung up on the cooling plate and wtr starting circulating before it slid off causing the water to spray over. Unit needs to be cleaned. Did a clean cycle customer is aware. Cleaned condenser and put a leak board under unit and took pic. Please fill out tech satisfaction survey. Thank You.
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS1
Near Woodland Park, Colorado 80863
Charles
Job Details:
09/03/2025
"Installed listed parts, unit not secured to counter or cabinets, no mounting brackets on unit, unit tilted forward and no room to adjust"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF991BOOM01
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
09/03/2025
Recharged to 5.5 oz of R134a unit was over charged 20 psi on low side. Cleaned evaporator and unclogged drain
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ02
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
09/03/2025
"Unit has a defrost issue, defrosted unit and replaced FC evaporator fan motor, unit needs time to cool, installed litmus strip and advised customer 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS3
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
09/03/2025
Installed sump assembly runs ok. Recommended customer clear cx reduce amount of dishes loaded. Left leak strip
We serviced a
MAYTAG WASHER
Model MVW5035MW2
Near Albuquerque, New Mexico 87112
Jason
Job Details:
09/03/2025
Checked unit only error code was present was off balance load. ran quick wash and spin cycles unit opperation checks ok at this time. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Los Lunas, New Mexico 87031
Larry
Job Details:
09/03/2025
Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Los Lunas, New Mexico 87031
Larry
Job Details:
09/03/2025
Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Los Lunas, New Mexico 87031
Larry
Job Details:
09/03/2025
CX complaint - Washer leaking - Inspected unit and found - the drain pump misaligned with hose - Adjusted hose and pump and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC2
Near Albuquerque, New Mexico 87111
Jason
Job Details:
09/03/2025
Checked unit ran cycle to test opperation of dosing pump. dosing pump opperation checks ok. instructed cx on were to go to get manual for appliance and how load and go opperates. spoke to cx about review
We serviced a
WHIRLPOOL RANGE
Model WFC315S0JW4
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
09/03/2025
"cx complanit - no power to unit - turned breaker off for 1 minute turned breaker back on no power checked voltage from outlet not reading,proper voltage.cx will have to call contractor that installed the new outlet or PNM - survey mentioned (some areas in RIO RANCHO has been having power outages)"
We serviced a
WHIRLPOOL WALL OVEN
Model WOS51EC0HS20
Near Los Lunas, New Mexico 87031
Larry
Job Details:
09/03/2025
installed ui and tested good - nit is good to go - Survey mentioned
We serviced a
GLADIATOR TRASH COMPACTOR
Model GACP15XXMG4
Near Bosque, New Mexico 87006
Larry
Job Details:
09/03/2025
CX complaint - Switch broke - Inspected unit and found the knob broke in the rotary switch - Both will need to be replaced - CX doesn't want to bear the cost of repair - Collected SC-auth-JM49C4 - Estimate in QP
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Glenwood Springs, Colorado 81601
James R
Job Details:
09/03/2025
Customer signed disclaimer. Replaced elec control then calibrated it and ran a service diagnostics. Unit operating as should. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ12
Near Bend, Oregon 97702
Levi
Job Details:
09/03/2025
"Replaced led modules and switch, tested good"
We serviced a
MAYTAG WASHER
Model MVW6200KW1
Near Pueblo West, Colorado 81007
Domingo
Job Details:
09/03/2025
Replaced gear case motor belt splutch capacitor impeller and and tub test it and it passed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ11
Near Los Lunas, New Mexico 87031
Larry
Job Details:
09/03/2025
Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
SUB ZERO BI REFRIGERATOR
Model 680/F
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
09/03/2025
"cust currently has power off at the house for some electrical repairs, found ground from the motor may have gotten down near the fan blade. remedied the issus i belie ve, but cust will call if issue persists"
We serviced a
WHIRLPOOL RANGE
Model WFE745H0FS0
Near Monument, Colorado 80132
Dvante
Job Details:
09/03/2025
"Checked unit, found the unit not heating at all. Checked and found the bake element damaged. Will need element replaced. Gave customer the quote. Customer decided not to move forward with repair due to the cost. She will get an element and install herself. Wont be held liable for damages in case when its installed by customer. Will just collect the service fee.Service Fee-$149.95$149.95 CC Auth# AX94YX"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Colorado Springs, Colorado 80920
Dvante
Job Details:
09/03/2025
"Checked unit, found items stuck in the filter lint assembly. Was able to get the items out. Tested unit and its running smoothly.Service Fee-$139.95$139.95 CC Auth# REY43T"
We serviced a
COVE DISHWASHER
Model DW2450
Near Powell Butte, Oregon 97753
Richard
Job Details:
09/03/2025
Installed new controls cycle tested unit on quick wash unit tested fine at time of repair unit working as designed at this time
We serviced a
SAMSUNG DRYER
Model DVE45B6300P/A3
Near Colorado Springs, Colorado 80916
Mathew
Job Details:
09/03/2025
"Found high limit thermostat tripped. Replace element assy. Test op, unit"
We serviced a
SAMSUNG DRYER
Model DVE50BG8300VA3
Near Sheridan, Oregon 97378
Nathan
Job Details:
09/03/2025
Replaced broken idler pulley and belt
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Pueblo, Colorado 81001
Domingo
Job Details:
09/03/2025
Replaced the division on the door and ran hass and it pass
We serviced a
SAMSUNG WASHER
Model WD90F53AVYUS
Near Roseburg, Oregon 97471
Thomas
Job Details:
09/03/2025
Replaced shocks. Ran tested okay with customer present. No leaks
We serviced a
SAMSUNG REFRIGERATOR
Model RF22R7351SR/AA
Near Roseburg, Oregon 97471
Thomas
Job Details:
09/03/2025
Replaced all parts listed. Ice maker harvested and filled. HASS passed. Advised customer
We serviced a
MAYTAG DRYER
Model MED7230HW0
Near Bend, Oregon 97702
Levi
Job Details:
09/03/2025
"Replaced heating element, tested all checks okay"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507ESS01
Near Woodland Park, Colorado 80863
Charles
Job Details:
09/03/2025
"Fridge evaporator frozen and fan loud, left door sagging, screw head broke off on lower door hinge, removed door and not enough screw left to grip and remove would have to drill out and use easy out to remove screw. Needs fan W11033168, screw W10673841, Service fee $189.95 pre-paid, Labor $319.95MPS $15.50 Parts $124.10 & $26.08Tax $12.31, Total $686.89, balance $496.94, left voicemail with owner, declined estimate"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT313CZLW00
Near Basalt, Colorado 81621
James R
Job Details:
09/03/2025
Customer signed disclaimer. Removed evap cover evap is not frosted up so it is going thru the defrost cycle. Installed heat probe per TSP W11759048 SP# S361BQ Reassembled unit evap fan and compressorc are running. Unit is operating as should. Please fill out tech satisfaction survey. Thank You.
We serviced a
MAGIC CHEF REFRIGERATOR
Model HVDR45B
Near Green Mountain Falls, Colorado 80819
Charles
Job Details:
09/03/2025
Installed cold control
We serviced a
LG REFRIGERATOR
Model LFXS26973S.ASTCNA1
Near Colorado Springs, Colorado 80923
David
Job Details:
09/03/2025
"Replaced freezer fan grill, fan is operating."
We serviced a
LG REFRIGERATOR
Model LRFC525D3S/00
Near Peyton, Colorado 80831
Brandon
Job Details:
09/03/2025
"Replaced compressor and drier, held vaccum and charged unit all checks ok"
We serviced a
LG REFRIGERATOR
Model LFXS28566M.AMTCNA0
Near Peyton, Colorado 80831
Brandon
Job Details:
09/03/2025
"Replaced compressor, drier and evapa cover assy, held vacuum and charged unit all checks ok"
We serviced a
LG DRYER
Model DLE8400BE
Near Eagle, Colorado 81631
Antonio
Job Details:
09/03/2025
Installed new element and cuttoff then ran a cycle for proper operation and unit tested good
We serviced a
LG M/W OTR
Model MVEM1825X/00
Near Colorado Springs, Colorado 80911
David
Job Details:
09/03/2025
"Checked microwave, control board not needed. Microwave has been running without shutting down, since JC turned vent fan to recirculation."
We serviced a
LG REFRIGERATOR
Model LRFXS2503S.ASTCNA1
Near Colorado Springs, Colorado 80916
Mathew
Job Details:
09/03/2025
"Remove and evac old compressor. Install new compressor, pupl into vacuum. Leak check. charge to spec. Monitor temps dropping. All okay."
We serviced a
LG REFRIGERATOR
Model LRFVS3006S.ASTCNA0
Near Colorado Springs, Colorado 80903
Charles
Job Details:
09/03/2025
Installed listed parts
We serviced a
LG BI REFRIGERATOR
Model LRRXC2606S.ASTCNA0
Near Beaver Creek, Colorado 81620
Antonio
Job Details:
09/03/2025
Installed icemaker and evap fan assembly then turn unit back on. Cycled the ice maker and unit tested good
We serviced a
LG DRYER
Model DLEX8900B.ABLEEUS
Near Peyton, Colorado 80831
Brandon
Job Details:
09/03/2025
Replaced pcb and tested operation all checks ok
We serviced a
LG DISHWASHER
Model LDPH7972S.ASSESNA
Near Colorado Springs, Colorado 80920
Brandon
Job Details:
09/03/2025
Replaced seal all checks ok
We serviced a
LG FREEZER
Model LRDCS2603S.ASTCNA0
Near Beaver Creek, Colorado 81620
Antonio
Job Details:
09/03/2025
Installed new door magnet. Unit tested good
We serviced a
MAYTAG DRYER
Model DG412
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
09/03/2025
"Customer states unit is taking awhile to dry. Inspected unit, wall vent clogged and choking flame, unit not heating past 88f, pulled vent hose off, unit heating sustained and heated to 206f, push at end of vent is not strong enough to open critter guard, recommend vent to be professionally cleared. Auth $139.95 #3N39CA"
We serviced a
SAMSUNG REFRIGERATOR
Model RS28A500ASR/AA
Near Medford, Oregon 97504
Jeff
Job Details:
09/03/2025
Went thru machine everything checks good at this time greats frost pattern no noises fans are good paid trip Auth 44l3nv id 2834974
We serviced a
JENN-AIR RANGE
Model JDRP548HL01
Near Larkspur, Colorado 80118
Dvante
Job Details:
09/03/2025
Checked unit and it had a faulty F8 error code. Checked both cooling fans and it was working. The unit needs to be updated through the JennAir app. JennAir will contact customer tomorrow to help with getting the unit updated.SR7742323967
We serviced a
GE WASHER
Model GTW465ASN2WW
Near Colorado Springs, Colorado 80906
David
Job Details:
09/03/2025
"Replaced drain pump, ran a speed wash. Advanced thru cycle and draining."
We serviced a
SUB ZERO WINE COOLER
Model IW-30CI
Near Prineville, Oregon 97754
Richard
Job Details:
09/03/2025
Installed new stepper valve per SZ tech support charged unit with 6.5oz 134a Freon cycled unit all tested fine at this time upper section started at 75 degrees before leaving was at 66
We serviced a
GE WASHER
Model GFW650SPN4SN
Near Gypsum, Colorado 81637
Erik
Job Details:
09/03/2025
INSTALL/ TEST: PASSJOB COMPLETE
We serviced a
GE RANGE
Model GRF600AV1SS
Near Gypsum, Colorado 81637
Erik
Job Details:
09/03/2025
INSTALL HARNESS AND BURNERS WITH SWITCH/ TEST: PASS * SEE QUICK PICSJOB COMPLETE
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Eagle, Colorado 81631
Erik
Job Details:
09/03/2025
INSTALL/TEST: PASSJOB COMPLETE
We serviced a
GE REFRIGERATOR
Model GTS17DTNNRWW
Near Green Mountain Falls, Colorado 80819
Charles
Job Details:
09/03/2025
Replaced control board
We serviced a
GE CAFE REFRIGERATOR
Model GNE25JYKJFFS
Near Monument, Colorado 80132
Ryan
Job Details:
09/03/2025
Unit out of level keeping door from closing properly. Adjusted level of unit and door now closing and sealing. RK
We serviced a
GE RANGE
Model CTC912P2N3S1
Near Monument, Colorado 80132
Ryan
Job Details:
09/03/2025
Did not arrive. Customer had service already from out company earlier in the day. RK
We serviced a
ELECTROLUX REFRIGERATOR
Model FFTR1835VS
Near La Junta, Colorado 81050
James
Job Details:
09/03/2025
"Installed ordered parts. Tested ops, unit held vacuum charged unit. Condenser line immediately started to get hot and unit cooled with good frost pattern. Cust is going to move fridge to different locations. Advised that if unit is tilted when moved unit must be left unplugged for 24 hrs to avoid oil contamination"
We serviced a
MAYTAG WASHING MACHINE
Model MVWB835DW4
Near Colorado Springs, Colorado 80915
David
Job Details:
09/03/2025
"Installed parts, ran calibration and diagnostic cycles. All good"
We serviced a
WHIRLPOOL WASHER
Model 110.28522701
Near Pueblo West, Colorado 81007
Domingo
Job Details:
09/03/2025
Check unit and everything was working fine told customer the water valve is the culprit but they just wanted to know what was wrong sc 139.95 customer pay check
We serviced a
JENAIR MICROWAVE
Model n/a
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
09/03/2025
"reset power and unit started working, cust to monitor..autho no. 3VL44H"
We serviced a
GE OVEN
Model JT3800SH4SS
Near Colorado Springs, Colorado 80906
David
Job Details:
09/03/2025
"Checked oven, replaced glass pack."
We serviced a
BOSCH MICROWAVE
Model HMB50152UC/05
Near Larkspur, Colorado 80118
Dvante
Job Details:
09/03/2025
"Checked unit, found door had a couple of dents. Went ahead and replaced door. Unit is operating as designed."
We serviced a
THERMADOR WALL OVEN
Model POD302RW/01
Near Vail, Colorado 81657
Erik
Job Details:
09/03/2025
adjust rear panel vibration causing fan 'buzz'install wall oven/ test: passJOB COMPLETE
We serviced a
BOSCH DISHWASHER
Model SHV878ZD3N/19
Near Aspen, Colorado 81611
Sean
Job Details:
09/03/2025
Verified the unit information & customer signed disclaimer..Checked the unit error codes and unit had a E19Dispenser issue or wiring. Removed the inside door panel and checked all wires and connections. Reattached everything..Reassembled the unit and tested the unit came on and started working as designed. Dign = unit had a loose wire The unit is operating as designed by factory.Please fill out a technician survey
We serviced a
WHIRLPOOL REFRIGERATOR
Model WZF34X18DW04
Near Pueblo, Colorado 81006
James
Job Details:
09/03/2025
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Albuquerque, New Mexico 87123
Jason
Job Details:
09/03/2025
Installed parts ran calibration and quick wash cycles. unit opperation checks ok. spoke to cx about review
We serviced a
GE WASHER
Model GFW655SPV0DS
Near Monument, Colorado 80132
Ryan
Job Details:
09/03/2025
Replaced main control board and tested all functions including pump. Unit is now working properlhy. Inst customer to run several self-clean cycled and to repeat monthly. RK
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Salem, Oregon 97302
Nathan
Job Details:
09/03/2025
Unit pressure switch failure Replaced main board
We serviced a
MAYTAG DRYER
Model MED7230HW
Near Pueblo, Colorado 81005
Domingo
Job Details:
09/03/2025
Replaced repair kit took coins off drum test it no noise
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Bend, Oregon 97701
Levi
Job Details:
09/02/2025
Found main pump is not working so I replaced main sump assembly and drain pump. Tested and all checks okay and no leaks detected at time of service. Customer was busy with a client and could not get date of occupancy paperwork as stated in attention note.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Medford, Oregon 97501
Jeff
Job Details:
09/02/2025
Installed parts tested machine working as should
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Lincoln City, Oregon 97367
Nathan
Job Details:
09/02/2025
Timer not advancing Replaced timer Apartment complex no proof of purchase Nobody around after service to sign
We serviced a
MAYTAG DRYER
Model MED6230RHW3
Near Grants Pass, Oregon 97527
Thomas
Job Details:
09/02/2025
Dryer set to timed dry and immediately turned off after starting up. Display showed a message about a forced restart and then the dryer kept working after that. 240V at terminal block. No errors in history. Spoke to Tim with Whirlpool TS. He recommended to try updating dryer software through Maytag app. He gave me file # 7742305957. Advised customer and assisted in setting up Maytag app. Ran successful update per dryer. Customer will monitor. Advised customer of survey
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Grants Pass, Oregon 97527
Thomas
Job Details:
09/02/2025
Replaced board. Calibrated washer. Ran tested okay with customer present. No leaks. Advised customer of survey
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Medford, Oregon 97501
Jeff
Job Details:
09/02/2025
Installed parts tested machine working as should
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Bend, Oregon 97701
Levi
Job Details:
09/02/2025
Found out the heating element was burned up so I replaced the element and the element thermostats. Tested and all checks okay
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80920
Dvante
Job Details:
09/02/2025
"Checked unit, has a F3E1 error code due to pressure sensors failing on control. Replaced control. Calibrated and tested diagnostic mode. No errors. Unit is operating as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo West, Colorado 81007
James
Job Details:
09/02/2025
"Installed ordered part, tested ops all ckok"
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS5
Near Monument, Colorado 80132
Dvante
Job Details:
09/02/2025
"Checked unit, couldnt detect a gas leak from each burner, gas valve, or lines. Was able to test it while on the phone with tech support. No issues with unitTech SupportSR7742307058Safety SR7742298351"
We serviced a
KITCHENAID REFRIGERATOR
Model KRQC736RPS00
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
09/02/2025
"SR- 7742308169 called tech line, no evidence of air leaks. Per techline Cx needs to ensure doors are closed completely to avoid Ice Bin to freeze over."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ12
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
09/02/2025
"Right RC door gasket torn from use, removed and replaced, needs time to set. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
09/02/2025
Installed repair kit runs all ok
We serviced a
KITCHENAID RANGE
Model KSDG950ESS8
Near Grand Junction, Colorado 81506
James R
Job Details:
09/02/2025
Customer signed disclaimer. Replaced door glass and then test operation in diagnostics checked faults. F8E0 cooling fan speed too low. Replaced cooling blower. Reassembled and connected down draft. Test operation to 400 degrees error code did not return. Unit is operating as should. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Silverthorne, Colorado 80498
Antonio
Job Details:
09/02/2025
Installed new ui panel and then ran a cycle for proper operation and unit tested good
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
09/02/2025
L1 has a dead leg in outlet cx needs an electrician to repair circuit
We serviced a
KITCHENAID DISHWASHER
Model KDTM404ESS3
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
09/02/2025
"Lower spray arm tab worn, spray arm fell off and is nit effectively washing, removed and replaced assembly, tested unit, working well now. Advised customer of situation and survey."
We serviced a
KITCHENAID M/W OTR
Model KMMF530PPS00
Near Peralta, New Mexico 87042
Larry
Job Details:
09/02/2025
Installed Vent motor and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Santa Fe, New Mexico 87501
Jason
Job Details:
09/02/2025
Checked unit found latch broken. installed parts listed ran spin cycle. unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WFC682CLW0
Near Rio Rancho, New Mexico 87144
Antonio
Job Details:
09/02/2025
cx complanit - error code FL/LO - used all parts shiped to cx home - unit is working as designed - survey mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Santa Fe, New Mexico 87501
Jason
Job Details:
09/02/2025
Installed control ran calibration andquick wash cycles unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Santa Fe, New Mexico 87508
Jason
Job Details:
09/02/2025
Installed control. ran calibration and quick wash cycles unit opperation checks ok
We serviced a
WHIRLPOOL RANGE
Model WFES3030RS0
Near Belen, New Mexico 87002
Larry
Job Details:
09/02/2025
CX complaint - Oven tripping breaker - Inspected unit and found the cook top works but it tripps about a minut into preheating - Performed service per SP-W11490386 - Unit is operating as designed - Survey mentioned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ07
Near Tome-Adelino, New Mexico 87031
Larry
Job Details:
09/02/2025
CX complaint - Door not closing properly - Inspected unit and found the door hinge missaligned - adjusted hinge and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM12
Near Albuquerque, New Mexico 87121
Larry
Job Details:
09/02/2025
CX compaint - Not making ice - Inspected unit and found the IM harness loose - Secured harness and tested good - Unit is good to go - Survey mentioned
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA 18
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
09/02/2025
"Intermittent cooling in fresh food section, temp sensors check ok, fans check ok, compressor checks ok, full frost pattern, dont recommend parts at this time, svf paid $139.95 CK Auth# 9CCMR3"

