We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB329DFBW05
Near Roseburg, Oregon 97471
Jeff
Job Details:
05/28/2025
Installed compressor put 44g r600. Unit cooling
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Sisters, Oregon 97759
Richard
Job Details:
05/28/2025
Installed new UI control cycle tested unit all tested fine at this time unit working as designed
We serviced a
MAYTAG WASHER
Model MVW6500MW0
Near Redmond, Oregon 97756
Richard
Job Details:
05/28/2025
Installed new agitator cycle tested unit all tested fine at time of repair.
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near La Pine, Oregon 97739
Levi
Job Details:
05/28/2025
"Tested unit and during agitation, I heard a clicking noise. Replaced clutch and slider assembly and performed another test. All checks okay"
We serviced a
MAYTAG WASHER
Model MVW6230RHW0
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
05/28/2025
"Installed cam, belt, actuator and capacitor ran diagnostic tests and calibration cycle, runs all ok"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
05/28/2025
"Checked unit, found no heat. Replaced heater and t stat. Tested diagnostic mode, checked heater and its getting 118 v. Heater is operating properly. Did advise customer to get smaller screws for the cheese grater bracket to prevent damaging the countertop"
We serviced a
MAYTAG DRYER
Model MEDP586KW0
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
05/28/2025
"Thermostat is providing lower temperature wavelengths, removed and replaced thermostat, tested unit, temperature wavelengths are good now. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
05/28/2025
"Inlet water valve is not properly dispensing water and temperature, removed and replaced water inlet valve, water levels are nit good with proper temperature. Advised customer of usage and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ00
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
05/28/2025
Installed module runs all ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW06
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
05/28/2025
"Installed water valve and filter housing runs ok, left leak strip"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS3
Near Colorado Springs, Colorado 80915
Jerimiah
Job Details:
05/28/2025
"Found blown noise fuse. Could not find culprit why it blew, switches in good status, no other shorts in system, replaced fuse, unit check ok. Disclosed survey to cust fcc 5star."
We serviced a
WHIRLPOOL WASHER
Model WTW500CMW0
Near Peyton, Colorado 80831
Aaron
Job Details:
05/28/2025
"Washer tub rotor cover touching the floor, water splashing on tub ring, corrected legs and teste on bulky cycle, working well now, now leaks, installed litmus strip and advised customer of survey."
We serviced a
MAYTAG WASHER
Model MVW7230HC1
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
05/28/2025
"Installed water valve ran tests runs all ok cx education, explained to cx function limitation on normal cycle, it does not fill completely with water as designed uses Auto fill regardless of Deep Fill selection"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ4
Near Fountain, Colorado 80817
Carlos
Job Details:
05/28/2025
"Installed sump assembly run all ok, left leak strip."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Monument, Colorado 80132
Dvante
Job Details:
05/28/2025
"Checked unit, found the speed on motor wasnt operating properly. Replaced the pump & motor assembly. Tested unit twice, no error codes or leaks. Unit is circulating inside properly."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB329DMBM05
Near Avon, Colorado 81620
Antonio
Job Details:
05/28/2025
Found water line frozen over due to not enough water pressure (water line was kinked) cycled ice maker unit tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL FREEZER
Model WZC5116LW0
Near New Castle, Colorado 81647
Sean
Job Details:
05/28/2025
Checked the unit MN SN POP Customer signed disclaimer Removed the compressor cover and checked the unit.Found that the inverter was smokes.Installed the new inverter and reassembled the unit Started the unit and watched compressor start Watched the box drop to 20? and falling. The unit tested good.Operating as designed by factory.If you are satisfied with the service I have provided you with today then please share your experience with others and fill out a online technician survey @ D-3 appliance.Thank you Sean
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Rifle, Colorado 81650
Josh
Job Details:
05/28/2025
Customer signed disclaimer. Verified MN SN POP.Customer states that unit is not forming enough ice. Technician found 15-20 well formed cubes in otherwise empty dispenser. Technician contacted manufacturer technical service and unit passed all performance tests. Manufacturer suggests adjustment of freezer cabinet temperature by -2F to correct and monitoring ice production. Technician performed recommended adjustment and communicated with customer via telephone. Manufacturer recommends follow up 72 hours after setting change. Reference number 7741653807.
We serviced a
MAYTAG DRYER
Model MGD7230HW3
Near Avon, Colorado 81620
Antonio
Job Details:
05/28/2025
Installed fuse and motor control panel is mia but not needed ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
KITCHENAID DISHWASHER
Model KDPE334GPS0
Near Colorado Springs, Colorado 80908
Dvante
Job Details:
05/28/2025
"Checked unit, found the unit not switching from spray arm to another. Checked and found diverter motor faulty. Replaced the pump & motor assembly. Tested diagnostic mode, no leaks or error codes. Unit is washing and switching spray arms properly. Unit is operating as designed."
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
05/28/2025
"Installed control board and UI, ran tests runs ok."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Florissant, Colorado 80816
Charles
Job Details:
05/28/2025
"No cold water, replaced inlet valve W11210463"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW06
Near Albuquerque, New Mexico 87123
Jason
Job Details:
05/28/2025
Installed air tower unit opperation checks ok. spoke to cx about review
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Albuquerque, New Mexico 87122
Jason
Job Details:
05/28/2025
Installed ice maker ran test cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL M/W OTR
Model WMH53521HZ06
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
05/28/2025
"cx complanit - mw spark with rack in - unit is working as designed - no damage no one was hurt,went over manuel with cx,called technical support and safety to have it documented - survey mentioned"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ0
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
05/28/2025
cx complanit - dw - not filling with water - used all parts shiped to cx home - unit is working as designed - survey mentioned
We serviced a
MAYTAG REFRIGERATOR
Model MRFF4236RZ01
Near Los Lunas, New Mexico 87031
Larry
Job Details:
05/28/2025
CX complaint - Light out - Inspected unit and found the lights dim and switch broken - Replaced with pre-id parts and tested good - Unit is good to go - Survey mentioned
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6200QLAA
Near Peyton, Colorado 80831
Brandon
Job Details:
05/28/2025
"Replaced compressor and drier, vacuumed and charged hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF26XAEBP/XAA
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
05/28/2025
Found 5 blinks on inverter board. Unit will need inverter board. Coz is repairing themselves.
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF705HPS
Near Albuquerque, New Mexico 87123
Jason
Job Details:
05/28/2025
Installed compressor pressures check ok cooling checks ok unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
05/28/2025
cx complanit - lid locked and no power - used all parts shiped to cx - unit is working as designed - survey mentioned
We serviced a
KITCHENAID COMBINATION OVEN
Model KOCE500ESS09
Near Colorado Springs, Colorado 80919
Jerimiah
Job Details:
05/28/2025
"Unit getting F6E8, found wire loose on noise filter board, caused error code to be produced. Repaired wiring. Unit check ok charged service call $160.94 CC Auth# MV9K93"
We serviced a
SUB ZERO REFRIGERATOR
Model CL4850SID/O
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
05/28/2025
"installed part and cycled and filled, ciust to monitor"
We serviced a
WOLF RANGE
Model DF486G-LP
Near Florissant, Colorado 80816
Charles
Job Details:
05/28/2025
"Said unit would start beeping when door opened and could not get to stop unless flipping breaker. Heated to 350 then 425, unable to duplicate. Told to take video if it happens again. Will wait till end of day for customer to contact me if issue occurs again. Have not heard back from customer, closed call."
We serviced a
WOLF RANGE
Model DF48650G/S/P/LP
Near Florissant, Colorado 80816
Charles
Job Details:
05/28/2025
Installed griddle rework kit 831961
We serviced a
KITCHENAID COMPACTOR
Model KUCS03FTSS0
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
05/28/2025
installed listed part and unit checked lkay
We serviced a
MIELE COFFEE MACHINE
Model CVA6805
Near Vail, Colorado 81657
Erik
Job Details:
05/28/2025
install grinder/ test: PASSJOB COMPLETE
We serviced a
SAMSUNG WASHER
Model WD53DBA900HZA1
Near Monument, Colorado 80132
Brandon
Job Details:
05/28/2025
Replaced nozzle and tested operation hass passed
We serviced a
SAMSUNG REFRIGERATOR
Model RF30KMEDBSR/AA
Near Colorado Springs, Colorado 80924
Brandon
Job Details:
05/28/2025
"Error 39c, 40c, 25c, Ice maker frozen, cleared all ice and replaced ice maker, auger and tray"
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
05/28/2025
"Unit not level, leveled unit and added high loop, tested operation all checks ok installed leak strip"
We serviced a
WHIRLPOOL DRYER
Model WED5000DW2
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
05/28/2025
"Checked unit, found the scraping and thumping noise coming from the unit. Checked behind and found the sponge between frame and blower. Tested unit and its running with no issues. Also advised customer to have an installer put on the new vent hose per SK. Service Fee-$139.95$139.95 CK Auth# M9T4C3"
We serviced a
SUBZERO REFRIGERATOR
Model BI-48SD/S/TH
Near Pueblo, Colorado 81005
James
Job Details:
05/28/2025
Found drain hole plugged causing water leak. Cleared out drain now working. Collected 319.90 $351.89 CC Auth# F4PYP3
We serviced a
LG REFRIGERATOR
Model LRFCS25D3S.ASTCNA0
Near Colorado Springs, Colorado 80909
Mathew
Job Details:
05/28/2025
"Evac system. Purge lines with rx11, clean out with nitrogen. Install new compressor and condenser. Test op, monitor unit. All okay. Cx to monitor unit."
We serviced a
LG WASHER
Model WM3770HVA.ASSEEUS
Near Colorado Springs, Colorado 80908
Dvante
Job Details:
05/28/2025
Replaced drain pump. Tested diagnostic mode twice. Unit was able to drain properly with no issues. Unit is operating as designed.
We serviced a
LG WASHER
Model WT6105CW.ABWETUS
Near Colorado Springs, Colorado 80909
David
Job Details:
05/28/2025
"Replaced drain pump. Ran a cycle, the water pumped out."
We serviced a
LG REFRIGERATOR
Model LFXS26596S.ASTCNA1
Near Peyton, Colorado 80831
Ryan
Job Details:
05/28/2025
Removed and replaced defective compressor. Recharged unit and is now cooling. Inst. customer to wait 24 hours before loading and for ice production to begin. RK
We serviced a
BOSCH WASHER
Model WFMC5440UC/15
Near Redmond, Oregon 97756
Richard
Job Details:
05/28/2025
Tested unit cleared drain pump of debris found waterlines screens plugged up with sand silt Corrected cycle tested unit all tested good at this time. Job complete. Customer paid by CC auth#4M943R tran#2424648
We serviced a
BOSCH RANGE
Model HDI8064U/01
Near Woodland Park, Colorado 80863
Charles
Job Details:
05/28/2025
Replaced relay board
We serviced a
JENN-AIR REFRIGERATOR
Model JBSFS48NMX00
Near Bend, Oregon 97701
Levi
Job Details:
05/28/2025
"Customer is hearing a vibration while cooling and if he touches the cover on the system compartment, the vibration stops. Cycled unit off/on to try and get unit to vibrate but could not replicate. Even removed compartment cover and looked for anything obvious and found none."
We serviced a
JENNAIR RANGE
Model JDRP436HL01
Near Bend, Oregon 97702
Levi
Job Details:
05/28/2025
"Replaced both convection fan motors. Tested, all checks okay"
We serviced a
SAMSUNG WASHER
Model WF42H5200APA2
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
05/28/2025
"Svf paid $139.95 CK Auth# 9HC3TH, drain clogged, removed clog and tested operation all checks ok"
We serviced a
GE DRYER
Model PFD95ESPT1DS
Near Vail, Colorado 81657
Antonio
Job Details:
05/28/2025
Installed new iderler pully and belt. Then ran a cycle for proper operation and unit tested good
We serviced a
GE DRYER
Model GTX33EASK1WW
Near Manitou Springs, Colorado 80829
David
Job Details:
05/28/2025
"Checked dryer, wire off heater terminal, not burned. Made sure terminal tight. Heating good and good air flow."
We serviced a
SUBZERO BI REFRIGERATOR
Model 642/0
Near Monument, Colorado 80132
Ralph
Job Details:
05/28/2025
"replaced parts and unit checked okay, cust to monitor"
We serviced a
SUB ZERO REFRIGERATOR
Model 690/F
Near Bend, Oregon 97702
Levi
Job Details:
05/28/2025
Customer was concerned about the temperature of the refrigerator since the door seal was installed. But the door seal seems to be perfectly fine. I did find one screw that was a little bit loose that may have prevented it from closing fully but other than that the temperatures measured good and the door is sealing perfectly
We serviced a
KITCHENAID ICE MACHINE
Model KUID308ESS1
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
05/28/2025
"PREFORMED YEARLY CLEANIMG AND REPLACED FILTER, NO ONE IN HOME CURRENTLY TO CHECK REPAIR OR SIGN WAIVERS OR RECIEPT"
We serviced a
BOSCH DISHWASHER
Model SHX3AR76UC/32
Near Vail, Colorado 81657
Antonio
Job Details:
05/28/2025
Installed new door handle unit look good
We serviced a
BOSCH DISHWASHER
Model SHV78CM3N/26
Near Beaver Creek, Colorado 81620
Erik
Job Details:
05/28/2025
ACCESS WITH SECURITYinstall door and sealJOB COMPLETECX not available for signature
We serviced a
MIDEA FREEZER
Model AUF-1720W
Near Woodland Park, Colorado 80863
David
Job Details:
05/28/2025
"Checked freezer, not level side to side, or front to back. Tipping forward and to the left. Leveled, and the door is closing and sealing much better."
We serviced a
LG DISHWASHER
Model LDF5545BD
Near Pueblo, Colorado 81005
James
Job Details:
05/28/2025
Found wires at tblock loose causing intermittent power issue. Re-wired and secured all ops test good. Collected 139.95 $139.95 CK Auth# VAX94V
We serviced a
KITCHENAID REFRIGERATOR
Model KSSS42QDX00
Near Florissant, Colorado 80816
David
Job Details:
05/28/2025
"Installed start device, unit started up and is cooling down."
We serviced a
JENNAIR REFRIGERATOR
Model JS42PPDUDB02
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
05/28/2025
"Removed and replaced bin cover, no scratches or dents, verified by customer. Total due was previously paid."
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Colorado Springs, Colorado 80918
Aaron
Job Details:
05/28/2025
"Removed and replaced components, tested unit through DLMS and diagnostic cycles, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
GE REFRIGERATOR
Model GFE28GYNFS
Near Colorado Springs, Colorado 80923
Ryan
Job Details:
05/28/2025
Found and repaired leak from recent compressor replacement. Pumped system down and recharged. Unit is now cooling. RK
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Pueblo, Colorado 81006
James
Job Details:
05/28/2025
Installed ordered part. Tested ops all ckok no leaks observed left litmus
We serviced a
MAYTAG DRYER
Model MED5630HC2
Near Bosque, New Mexico 87006
Larry
Job Details:
05/28/2025
Installed parts lsited and tested good - Unit is good to go
We serviced a
MAYTAG DRYER
Model MED7230HC2
Near Colorado Springs, Colorado 80920
Dvante
Job Details:
05/28/2025
"Checked unit, found the unit not tumbling. Checked inside and found thermal fuse open. Replaced fuse. Unit is tumbling and heating. Unit is operating as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ18
Near Bend, Oregon 97701
Levi
Job Details:
05/27/2025
"Replaced valve and filter housing assembly. Tested, all checks okay"
We serviced a
MAYTAG WASHER
Model MVW5435PW0
Near Redmond, Oregon 97756
Richard
Job Details:
05/27/2025
Installed new control board cycle tested unit
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Grants Pass, Oregon 97527
Thomas
Job Details:
05/27/2025
Customer had an emergency earlier today so I came back in the afternoon. Replaced motor/sump assembly. Ran tested okay no leaks. Advised customer of survey
We serviced a
WHIRLPOOL WASHER
Model WFW4720RW0
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
05/27/2025
"Unit is not level due to front right leg, corrected and verified, customer verified, no error codes on unit, pins are pulled, inner outer tub movement is good, recommend weight is pedestal drawer. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
05/27/2025
"No error codes upon arrival, front right leg not level, unit going off balance, corrected and tested unit through diagnostics, working well now, secured drain hose to help prevent movement during spin. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKB3
Near Fountain, Colorado 80817
Carlos
Job Details:
05/27/2025
Garbage disposal drain connection was not punched out. Drains all ok.
We serviced a
WHIRLPOOL RANGE
Model WFE550S0LZ3
Near Manitou Springs, Colorado 80829
Carlos
Job Details:
05/27/2025
Installed glides all ok
We serviced a
WHIRLPOOL WASHER
Model MVW7230HC1
Near Fountain, Colorado 80817
Carlos
Job Details:
05/27/2025
Installed control board and water valve runs all ok
We serviced a
MAYTAG REFRIGERATOR
Model MBF1958FEZ08
Near Trinidad, Colorado 81082
James
Job Details:
05/27/2025
Installed ordered parts tested ops all ckok
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Gypsum, Colorado 81637
Antonio
Job Details:
05/27/2025
Unit needs drain pump sr#7741522460Pt$97.96 w11497943Lb$189.95Mpg$17.50Cx is holding on repairing
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ11
Near Grand Junction, Colorado 81503
Josh
Job Details:
05/27/2025
"Customer signed disclaimer. Verified MN SN POP.Technician confirmed correct component received in good condition. Technician installed replacement ice bin assembly. Tech filled with ice from previous bin and performed test. Unit dispensed ice correctly on demand. Unit is functioning properly within manufacturer specifications.Thank you for allowing us to service your refrigerator today! Please take a moment to let us know how weve done by completing our technician satisfaction survey! Call us with any questions or all your appliance needs, and have a great day!"
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Grand Junction, Colorado 81505
Josh
Job Details:
05/27/2025
"Customer signed disclaimer. Verified MN SN POP. Customer states that unit has not worked for the last two weeks, that unit washes but will not rinse. Technician performed customers cycles of concern (delicate x2, mixed and rinse & spin) with unit functioning properly loaded with 4 towels through all cycles. Customer initiated fifth delicate cycle that failed to drain, inspection found a towel wedged in the auger blade and after removal, drain and spin function properly. Recommend verifying enough water is used for load size during wash, and if necessary, ensuring the auger blades are free of clothing before starting a rinse/spin to ensure operation."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Eagle, Colorado 81631
Antonio
Job Details:
05/27/2025
Installed new sump assembly then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL WASHER
Model MVW6230HW4
Near Grand Junction, Colorado 81505
Josh
Job Details:
05/27/2025
"Customer signed disclaimer. Verified MN SN, Cx looking for POP.Customer states that unit becomes out of balance on most/all cycles. Inspection found a damaged rt front leveling foot. Technician replaced from item on true ck and performed loaded test cycle consisting of 8 towels. Unit filled, agitated and spun properly, quickly and correctly balancing on high spin. Unit is now functioning properly within manufacturer specifications."
We serviced a
WHIRLPOOL DRYER
Model WED72HEDW0
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
05/27/2025
"Idler and rollers are worn from use, idler sticking intermittently, removed and replaced components, tested unit, working and heating well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, Colorado 80938
Aaron
Job Details:
05/27/2025
"Thermistor shorted out, ice in heating element connection, control is not sending power to components, removed and replaced components, unit needs time to cool. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM13
Near Santa Fe, New Mexico 87507
Jason
Job Details:
05/27/2025
installed valve checked opperation of valve unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM12
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
05/27/2025
cx complanit - loud buzzing noise - uesd all parts that were ship to cx home - buzzing sound gone - unit is working as designed - survey mentioned
We serviced a
WHIRLPOOL WALL OVEN
Model WOES3030LS01
Near Rio Rancho, New Mexico 87124
Antonio
Job Details:
05/27/2025
"cx complanit - unit smoking - unit is working as designed no one explained to cx about the oil burning off the bake and broil element,cx has been living in new home for one month,called technical support to have it documented - (SR# 7741642054"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Santa Fe, New Mexico 87508
Jason
Job Details:
05/27/2025
Installed control ran diagnostic and timed dry cycle to checks door switch opperation unit opperation checks ok. spoke to cx about review
We serviced a
MAYTAG DRYER
Model MGDP575GW0
Near Los Ranchos de Albuquerque, New Mexico 87107
Larry
Job Details:
05/27/2025
"CX complaint - stops during dry cycle sensor - dryer keeps overheating or something after one load - Replaced parts listed and tested good - Unit should be good to go; used 1 WP338906 (Sensor), 1 WP3391912 (Therm-Fix), and 1 WPW10298258 (Sensor) from stock"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Rio Rancho, New Mexico 87144
Antonio
Job Details:
05/27/2025
cx complanit - clothing wet at the end of cycle - used all parts that were shiped to cx home - unit is working as designed - survey mentioned
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Santa Fe, New Mexico 87507
Jason
Job Details:
05/27/2025
installed console and control ran quick cycle to verify opperation of unit. unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW6157PB0
Near Albuquerque, New Mexico 87121
Larry
Job Details:
05/27/2025
CX complaint - Agitator broke - Replaced with pre-id parts and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Albuquerque, New Mexico 87121
Larry
Job Details:
05/27/2025
CX complaint - DW fills but wont run - Inspected unit and found the wash pump failed - Replaced with pre-id part and tested good - Unit is good to go
We serviced a
MAYTAG REFRIGERATOR
Model MFT2574DEM02
Near Redmond, Oregon 97756
Richard
Job Details:
05/27/2025
Replaced defrost heater and fan motor harness cycled unit all tested fine at this time
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS1
Near Albuquerque, New Mexico 87120
Larry
Job Details:
05/27/2025
CX complaint - F8E4 error - Inspected unit and found the gasket failed flodding the float switch - Replaced both with pre-id psrts ad tested good - Unit is good to go
We serviced a
THERMADOR FREEZER
Model T30IF70NSP/03
Near Colorado Springs, Colorado 80904
Charles
Job Details:
05/27/2025
"Not making ice, could be issue with bin engagements of switch, need ice maker 11012681Service fee $159.95, Labor $229.95, MPS $14.50, Part $1264.78, Tax $103.71, Total 1772.89, declined estimate at this time, 30 day estimate. Paid service fee check#1918 autho 3LKX4F"
We serviced a
WOLF RANGE
Model IR36550/S/P
Near Monument, Colorado 80132
Charles
Job Details:
05/27/2025
"Right rear leg wont adjust, bolt backed out of thread, prop up unit and threaded bolt, adjusted to counter top."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF707ESS01
Near Santa Fe, New Mexico 87501
Jason
Job Details:
05/27/2025
Checked unit found led modules need to be replacedSC$244.95MPS$17.50LED MODULE KIT#W11683242 $304.95LABOR$229.95TX$46.95TOTAL$844.30Auth code: 4TMU3U$244.95cx to think repair over
We serviced a
WHIRLPOOL DRYER
Model WED9600TW1
Near Trinidad, Colorado 81082
James
Job Details:
05/27/2025
Installed ordered parts tested ops all ckok collected 199.95 $199.95 CC Auth# 4HEPR9
We serviced a
SAMSUNG MICROWAVE
Model ME16A4021AS/AA
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
05/27/2025
Replaced door and tested op all checks ok
We serviced a
SAMSUNG DRYER
Model DVE55CG7500EA3
Near Peyton, Colorado 80831
Mathew
Job Details:
05/27/2025
"Ran vent test, c90 displays. Found obstruction in venting. Cleared obstruction, shortened venting. Test op, oqc passes, vent test passes. All okay."