We serviced a
MAYTAG REFRIGERATOR
Model MRT311FFFH01
Near Medford, Oregon 97504
Jeff
Job Details:
03/13/2025
Found that the frig is an indoor frig only page 5 of owners manual and will not work correctly in temperatures below 55 degrees or above 110 degrees relayed to customer.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Culver, Oregon 97734
Levi
Job Details:
03/13/2025
Found heating element was burned out so I replaced it along with the thermostat kit. Tested all checks okay. Also checked venting and venting is good yeah you never kn
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKB3
Near Bend, Oregon 97701
Levi
Job Details:
03/13/2025
"Complaint is they are hearing a series of about 3 clicks 1.5 hours into the cycle. Most likely the heating element relay. This unit is not insulated like many models so the sounds of the relays may be echoing inside the door. During diagnostics, all the noises I heard are normal"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS05
Near Bend, Oregon 97702
Levi
Job Details:
03/13/2025
"Replace door hinge pieces, tested and all checks okay"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Bend, Oregon 97702
Levi
Job Details:
03/13/2025
"Replaced lid switch and control board, tested, all checks okay. Performed recalibration cycle. Sucess"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Applegate, Oregon 97530
Thomas
Job Details:
03/13/2025
Replaced chute and kit. Ran tested okay no leaks
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS01
Near Sisters, Oregon 97759
Levi
Job Details:
03/13/2025
"Replaced defective compressor, charged with 5.25oz of r134a, pressures are spot on at about 1psi on the low side and 125 on the high side. Unit is cooling and should be great. Water line needs replaced due to slight leaking at both ends. Customer will run and get a new one to replace it."
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Medford, Oregon 97504
Jeff
Job Details:
03/13/2025
Installed shafts put repair kit in it tested machine and sounds normal
We serviced a
WHIRLPOOL WALL OVEN
Model WOC75EC0HS20
Near Jacksonville, Oregon 97530
Jeff
Job Details:
03/13/2025
Called tech line and was informed this unit is going to be exchanged. They also showed me there email they received Tuesday. Pic taken.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Colorado Springs, Colorado 80938
Aaron
Job Details:
03/13/2025
"Removed and replaced controls, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
03/13/2025
"F0E3 overload/unbalanced load error code upon arrival, inspected unit, out of balance load pulled water connection to dispenser drawer, corrected and monitored, dispenser drawer is working well, no detergent in, recommend smaller loads, unit has updated tub ring. Advised customer of situation and survey. Discussed situation with techline. SR7741140014"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
03/13/2025
"Called techline SR-7741134991, unit works as designed, normal cycle always begins with normal water and introduces hot water if selected throughout the rest of the cycle, same function permeates on all other cycles this is designed as such to preserve energy do to being a High efficiency model."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Colorado Springs, Colorado 80938
Aaron
Job Details:
03/13/2025
"Circulation motor is shorted out, removed and replaced motor sump assembly, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ5
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/13/2025
"F8E0 blower fan speed error code using arrival , found loose connection at plastic connector to blower, corrected and tested unit to 350f, blower came on at 155f and working well, on during cool down period. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
03/13/2025
"Replaced the wire harness and capacitor. Tested diagnostic mode, lid is locking, basket is spinning, no leaks or error codes. Unit is operating as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
03/13/2025
"Installed basket and suspension, ran calibration cycle and tests runs all ok"
We serviced a
MAYTAG DRYER
Model MGD6630MBK0
Near Winter Park, Colorado 80482
Antonio
Job Details:
03/13/2025
Installed new acu then ran dryer threw a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL WASHER
Model WTW5015LW0
Near Granby, Colorado 80446
Antonio
Job Details:
03/13/2025
"Installed new gear case, cam and belt ran a cycle for proper operation and unit tested good"
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Granby, Colorado 80446
Antonio
Job Details:
03/13/2025
Installed a new acu and ui panel and heated a cup of water for 1 minute and heated the oven to 350? and 5 tested good Also advised cx of whlp survey
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Granby, Colorado 80446
Antonio
Job Details:
03/13/2025
Installed a new acu and ui panel and heated a cup of water for 1 minute and heated the oven to 350? and 5 tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF989SDAM03
Near Fountain, Colorado 80817
Ralph
Job Details:
03/13/2025
replaced listed parts andunit checked okay
We serviced a
MAYTAG DRYER
Model MEDC200XW1
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
03/13/2025
Replaced timer. Unit is heating consistently now. No cold air. Unit is operating as designed.
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, Colorado 80906
Mathew
Job Details:
03/13/2025
Replaced cracked fan and faulty drive motor. Ran test on unit. All okay.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
03/13/2025
Disconnected wire at capacitor reconnected runs all ok
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Edgewood, New Mexico 87015
Jason
Job Details:
03/13/2025
Installed suspension ran spin cycle to check unit opperation unit opperation checks ok spoke to cx about review
We serviced a
AMANA DRYER
Model NED4655EW1
Near Edgewood, New Mexico 87015
Jason
Job Details:
03/13/2025
Checked unit found element had shorted. installed element and cutoff. ran timed dry cycle unit opperation checks ok. spoke to cx about review
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS3
Near Sandia Park, New Mexico 87047
Jason
Job Details:
03/13/2025
Installed drain pump ran normal cycle to checks opperation unit opperation checks ok. spoke to cx about review
We serviced a
MAYTAG M/W OTR
Model MMV1175JZ01
Near Sandia Park, New Mexico 87047
Jason
Job Details:
03/13/2025
Installed control ran cook cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ1
Near Albuquerque, New Mexico 87123
Jason
Job Details:
03/13/2025
Installed console and ui ran normal cycle to check function unit checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Santa Fe, New Mexico 87501
Antonio
Job Details:
03/13/2025
"cx complanit - unit is not working - called technichnician to have it documented - ran diagnostic on unit, passed - drain line did not have high loop, put drain loop unit is working properly - survey mentioned"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW2
Near Los Lunas, New Mexico 87031
Larry
Job Details:
03/13/2025
"Installed basket, calibrated load size and tested good - Unit is good to go - Survey mentioned"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Albuquerque, New Mexico 87110
Jason
Job Details:
03/13/2025
Installed parts listed ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DRYER
Model WED5100HW3
Near Albuquerque, New Mexico 87120
Larry
Job Details:
03/13/2025
Installed UI and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW8800YC0
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
03/13/2025
"Called techline SR- 7741137000. Ran test, unit was overloaded causing clothes to not be expunged of water. Cx has to run Clean Washer cycle to calibrate unit cx paid SC $139.95 CC Auth# 3YXNTP"
We serviced a
WOLF RANGE
Model RS64GLP
Near Larkspur, Colorado 80118
Charles
Job Details:
03/13/2025
"Installed broil safety valve, preformed gas leak test while running broiler."
We serviced a
COVE DISHWASHER
Model DW2450WS
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
03/13/2025
replaced door seal and saw no signs of leaking put a leak strip underneath and cust to monitor
We serviced a
SUB ZERO REFRIGERATOR
Model CL4850S/O
Near Colorado Springs, Colorado 80919
Charles
Job Details:
03/13/2025
"Customer emptied ice bin at 8:30pm, bin 1/4 full 14 hours later. Confirm with tech line ice production is normal. 8 cubes every 2-3 hours."
We serviced a
WOLF RANGE
Model DF60650CG/S/P
Near Colorado Springs, Colorado 80908
Jerimiah
Job Details:
03/13/2025
Installed rework kit. Unit check ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF305ESS08
Near Monument, Colorado 80132
Dvante
Job Details:
03/13/2025
"Checked unit, found the unit was noisy. Found the noise coming from the damper control. Motor is making the loud noise when opening and closing. Will need damper control replaced. Customer decided to move forward with the repair. Customer paid in full.Service Fee-$149.95Labor-$189.95Part-$186.40Supplies-$14.50Tax-$15.28Total-$556.08$366.13 CC Auth# 3ARPLH1 year warranty on part No return on parts$189.95 CC Auth# L9T4LH"
We serviced a
WHIRLPOOL DRYER
Model WED9400VE0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/13/2025
"F01 error code upon arrival, verified power to control, thermal fuse checks out okay, control is no longer available from the manufacturer. Auth $139.95 #VEP339"
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
03/13/2025
"Clothes got stuck in motor, removed and tested hass passed"
We serviced a
SAMSUNG WASHER
Model WA50R5200AW/US
Near Colorado Springs, Colorado 80918
Brandon
Job Details:
03/13/2025
"Error UB, unit unbalanced caused unit to not spin, balanced and tested hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23R6201SR/AA
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
03/13/2025
"Error 39 c, replaced ice maker hass oqc passed"
We serviced a
MAYTAG WASHER
Model MVWX655DW0
Near Albuquerque, New Mexico 87112
Jason
Job Details:
03/13/2025
Checked over unit found unit to be opperaating as designed ran multiple cycles.unit checks ok. spoke to cx about reviewAuth code: J4AXFL$151.84
We serviced a
LG DRYER
Model DLE7150W
Near Colorado Springs, Colorado 80920
Jerimiah
Job Details:
03/13/2025
"Unit getting error code D90. Was set up for Techline, found error represents blocked return air, Cust will get vent cleaners out to work on location. Charging service call. $153.95 CC Auth# MJHAK9Ticket # 578427"
We serviced a
DACOR REFRIGERATOR
Model EF48DBSS02
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
03/13/2025
installed listed part and unit checked okay
We serviced a
KITCHENAID REFRIGERATOR
Model KBFS25EWMS10
Near Colorado Springs, Colorado 80919
Charles
Job Details:
03/13/2025
"Ice maker failed. Needs ice maker W10884390. Went to Marcone for part and return. Service fee $139.95, Labor $189.95, MPS $14.50, Part $131.72, Tax $10.80, Total $486.92 paid autho 3M3FNN"
We serviced a
MIELE COFFEE MACHINE
Model CVA7440
Near Winter Park, Colorado 80482
Erik
Job Details:
03/13/2025
install bean containers and test: PASS * see quick picsJOB COMPLETECX not available for signature
We serviced a
MIELE COOKTOP
Model KM7740FR
Near Colorado Springs, Colorado 80919
Charles
Job Details:
03/13/2025
Move cooktop 1/4 inch left.
We serviced a
GE WASHER
Model GTW680BSJ3WS
Near Colorado Springs, Colorado 80916
David
Job Details:
03/13/2025
"Checked washer, control is skipping to end on different cycles. Several error codes. Will need control. Cx is thinking about repairs. Quote in quick pics. Service fee good for 30 days."
We serviced a
JENN-AIR WALL OVEN
Model JMC2430LL00
Near Santa Fe, New Mexico 87508
Antonio
Job Details:
03/13/2025
"cx complaint - console - replace console,unit is working properly - survey mentioned"
We serviced a
BOSCH DISHWASHER
Model SHP865WF5N/01
Near Colorado Springs, Colorado 80911
Charles
Job Details:
03/13/2025
"E25 drain error, no water in unit. Nothing in pump, started cycle and advised in clean cycle. Service fee $159.95 paid check 19733 autho PC3AA4"
We serviced a
JENNAIR COOKTOP
Model JIC4430XS00
Near Colorado Springs, Colorado 80920
Jerimiah
Job Details:
03/13/2025
Installed replacment glass cooktop. Upon installation back into countertop noticed that unit did not go flush to counter as rubber gasket is not on new glass top. Distance from glass to counter is same as thickness of gasket. Cust was made aware of situation. Cust had info to original installers of unit. Put in a call to S&K but never returned call. Charged labor as quoted $249.95 CC Auth# E49JMR
We serviced a
MONOGRAM DISHWASHER
Model ZDT985SINCII
Near Carbondale, Colorado 81623
Sean
Job Details:
03/13/2025
Checked the unit MN SN POP Customer signed disclaimer Opened unit and pulled the unit out.And lowered the unit removed door.Door handle came off . I reattached it to the wood panel.Wood panel is water swollen. And kick plate is bolted to the kick plate of dishwasher. Removed the hing and springs on both sides and installed new hinges and springs put on new rollers and reassembled the unit. Tested unit no longer makes the sound.Tested good.Please fill out a tech servey Thank you.
We serviced a
GE DRYER
Model GTX33EASK1WW
Near Granby, Colorado 80446
Erik
Job Details:
03/13/2025
CX NOT ON SITE - ACCESS WITH GARAGE CODEinstall themostat and hi limit/ test: PASSJOB COMPLETECX not available for signature
We serviced a
GE RANGE
Model GRS500PV1SS
Near Fraser, Colorado 80442
Erik
Job Details:
03/13/2025
CX NOT ON SITE - ACCESS WITH GARAGE CODE/ DOOR CODEtest power supply - GOOD 120vAC L1/L2check behind control panel - disconnected N to MCBreconnect and test: PASSBAKE/ BROIL - GOODALL burners - GOODJOB COMPLETECX not available for signature
We serviced a
GE RANGE
Model CGS700P2M3S1
Near Winter Park, Colorado 80482
Erik
Job Details:
03/13/2025
CX NOT ON SITE - ACCESS WITH DOOR KEY IN LOCK BOXinstall fan and trim/ test: PASS * see quick picsJOB COMPLETECX not available for signature
We serviced a
MONOGRAM REFRIGERATOR
Model ZISS480DNHSS
Near Aspen, Colorado 81611
Sean
Job Details:
03/13/2025
Checked unit MN SN POP Customer signed disclaimer.Opened up fresh food compartment and looked at the gasket. It was hanging out and smashed on bottom part of gasket. Opened up the package for the new gasket and checked it. It was in good condition. Soaked it in hot water and flattened it out. Removed old gasket and installed the new one. I used my steamer to make adjustments to it.Tested seal it was good .Tested unit good.Please fill out a tech servey.
We serviced a
KENMORE WASHER
Model 11047512601
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
03/13/2025
Spin cycle not balancing clothes due to worn suspension.Estimate for suspension replacement declined by customer.RK Auth UC9MX9
We serviced a
KENMORE REFRIGERATOR
Model 10657703701
Near Colorado Springs, Colorado 80915
David
Job Details:
03/13/2025
"Evap motor running then turns off, power full time. Picked up and replaced motor. Running good."
We serviced a
THERMADOR WALL OVEN
Model POD302RW/04
Near Colorado Springs, Colorado 80906
Jerimiah
Job Details:
03/13/2025
Unit again making noise intermittently either during heating or right away. Called techline. Cust has timestamp video showing its a bad racket of noise. Last time replacing conv motor assy noticed smaller motor fan was hitting particular portion of back of frame and exposed bare metal. Techline made a case for this unit case#410513219. Unit set of for review. Closing call
We serviced a
KENMORE FREEZER
Model 253.22042410
Near Colorado Springs, Colorado 80906
Charles
Job Details:
03/13/2025
"Installed door closure mechanism 5304511026, customer had part. Service fee139.95, Labor $189.95, MPS $14.50, Total 204.45 paid autho 3V9UY3"
We serviced a
KITCHENAID ICEMAKER
Model KUIX535HPS012
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
03/13/2025
"Unit has seal system leak, 40 psi on high side, circulation and drain pump runs ok cx will not repair cx paid SC $139.95 CK Auth# 9334NE"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Peyton, Colorado 80831
David
Job Details:
03/13/2025
"Installed ordered parts, tested and is operating good."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5001SR/AA
Near Pueblo West, Colorado 81007
Domingo
Job Details:
03/13/2025
Replaced compressor and filter drier liquid line got hot and refrigerator start it to cool also replaced board
We serviced a
SAMSUNG COMBINATION OVEN
Model NQ70M6650DS/AA
Near Monument, Colorado 80132
Jerimiah
Job Details:
03/13/2025
"Tried alleviating Cust of concerns unit has had with the previous repair(s), how a combination of components could have different ramifications in the future due to previously received bad components and miscommunication with Samsung giving wrong part numbers. With proximity of prices of parts of what was originally needed (and used) vs what was originally given as part number to order, both glass and console board are covered for a year. Cust will keep track of unit functionality and will contact Samsung if anything further develops. Closing call"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM02
Near Grants Pass, Oregon 97526
Thomas
Job Details:
03/12/2025
Used heat gun to reshape gaskets to fit better against the cabinet. Customer will monitor
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Bend, Oregon 97702
Levi
Job Details:
03/12/2025
"Installed door and nameplate, checked okay"
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ10
Near Cave Junction, Oregon 97523
Thomas
Job Details:
03/12/2025
Replaced thermistor. Set to ideal currently. Customer will monitor
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JW3
Near Talent, Oregon 97540
Jeff
Job Details:
03/12/2025
Burners installed
We serviced a
MAYTAG RANGE
Model MES8800PZ0
Near Ashland, Oregon 97520
Jeff
Job Details:
03/12/2025
Installed consoles wiring harness didn't have the lights but was able to get working
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Grants Pass, Oregon 97526
Thomas
Job Details:
03/12/2025
Black plastic hose in bottom corner rubs against plastic cover. Taped up section of black plastic hose and section of plastic cover
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT138FFDM03
Near Medford, Oregon 97501
Jeff
Job Details:
03/12/2025
Installed compressor put 48 g r600
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
03/12/2025
Needs a control Board. Unit constantly tries to drain
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS3
Near Colorado Springs, Colorado 80920
Dvante
Job Details:
03/12/2025
"Replaced the diverter disc. Tested diagnostic mode, no leaks, noises, or error codes. Unit is operating as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Peyton, Colorado 80831
Aaron
Job Details:
03/12/2025
"Capacitor is shorted out, removed and replaced, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model ATW4516MW0
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
03/12/2025
"Unit was non stop draining, reset unit and ran calibration cycle. Unit runs ok cx will observe"
We serviced a
KITCHENAID ICE MACHINE
Model KUID308HPS02
Near Rocky Ford, Colorado 81067
James
Job Details:
03/12/2025
Installed ordered parts tested ops all ckok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC136RPS00
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
03/12/2025
"Ran tests, unit cools ok, noises sound normal, amperage at 1.2 amps ,adjusted drier to 45 degree angle cx will observe if unit noise gets louder instructed cx to take video."
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Pueblo, Colorado 81006
James
Job Details:
03/12/2025
Found loose wire at drain pump causing no drain. Secured and tested all ops test good
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW1
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
03/12/2025
"Unit has F0E9 code present, indicating off balance pause. Unit is designed to stop spin cycle if it is overloaded or load is off balance."
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Florissant, Colorado 80816
David
Job Details:
03/12/2025
"Installed control board, ran diagnostic cycle. Spinning and draining great."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Ordway, Colorado 81063
James
Job Details:
03/12/2025
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHV06
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/12/2025
"Loose connection at auger motor plastic retainer, replaced motor, verified secure connection. Tested unit, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Fountain, Colorado 80817
Carlos
Job Details:
03/12/2025
Installed wash motor ran tests runs all ok left leak strip
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Carbondale, Colorado 81623
Sean
Job Details:
03/12/2025
"Checked unit MN SN POP Customer signed disclaimer Checked package = Good Unhooked power and removed spray arm and strainer.Unhooked wires to the pump, the drain, and the water sensor. Removed pump motor assembly.Installed the new pump motor assembly and hooked it back in the unit reassembled. Restored power.Tested unit on quick wash .Unit pumps water and drains. All spray arms are free and spin.Tested the unit good.Please fill out a technician survey.Thank you."
We serviced a
JENNAIR REFRIGERATOR
Model JFX2897DRM02
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
03/12/2025
"Replaced the evaporator fan motor assembly. Tested diagnostic mode, no shorted thermistor and bimetallic thermostat. No error codes on display. Unit is operating as designed."
We serviced a
WHIRLPOOL M/W OTR
Model WML55011HS06
Near Peyton, Colorado 80831
Aaron
Job Details:
03/12/2025
"Removed and replaced components, tested unit, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Monument, Colorado 80132
Dvante
Job Details:
03/12/2025
"Replaced pump and motor assembly. Tested diagnostic mode, no error codes or leaks. Unit is operating as designed."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404ESS3
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
03/12/2025
"Unit leaking left corner when lower spray arm rotates, wave splashing onto door insulation and saturating it, corrected and lifted front legs, monitored unit, working well now, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5015LW0
Near Albuquerque, New Mexico 87111
Jason
Job Details:
03/12/2025
Installed parts ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Los Lunas, New Mexico 87031
Larry
Job Details:
03/12/2025
"Installed control, ran load size calibrating and tested good - Unit is good to go - Survey mentioned"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Albuquerque, New Mexico 87111
Jason
Job Details:
03/12/2025
Installed dispensor ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Tijeras, New Mexico 87059
Jason
Job Details:
03/12/2025
Checked unit found drain pump wire connection was not seated re-seated plug ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Tijeras, New Mexico 87059
Jason
Job Details:
03/12/2025
Checked unit found drain pump wire connection was not seated re-seated plug ran quick cycle unit opperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Belen, New Mexico 87002
Larry
Job Details:
03/12/2025
CX complaint - Not making ice - Inspected unit and found the fill spout blocked with ice - Cleared ice and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DRYER
Model WGD5100HW3
Near Albuquerque, New Mexico 87122
Jason
Job Details:
03/12/2025
Checked unit found panel vibrating tightened panel re-tested unit opperation check ok spoke to cx about review
We serviced a
MAYTAG DRYER
Model MED6230HW2
Near Bend, Oregon 97701
Levi
Job Details:
03/12/2025
"Replaced rollers, belt and pulley using a maintenance kit, tested, all checks okay.; used 1 4392067RC (Dryer maintenance kit) from stock"
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Los Lunas, New Mexico 87031
Larry
Job Details:
03/12/2025
Installed parts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
KITCHENAID DISHWASHER
Model KUDS30IVBL4
Near Albuquerque, New Mexico 87110
Jason
Job Details:
03/12/2025
Installed piump motor assy ran quick cycle unit opperation checks ok spoke to cx about review