We serviced a
BOSCH MICROWAVE
Model HMCP0252UC/05
Near Vail, CO 81657
Erik
Job Details:
10/06/2023
install/ test: no arc/ heat 1 cup water in 1 minJOB COMPLETE
We serviced a
MAYTAG WASHER
Model MHW6630HW3
Near Colorado Springs, CO 80924
Aaron
Job Details:
10/06/2023
"F5E2 lid lock error code upon arrival, accumulated soap and dirt debris between Inner and outer tub, dispenser drawer clean, customer states they have used the 'clean washer' cycle several times. Discussed situation with techline and sent attached photos. Recommend several Affresh cleaning cycles SR7737063727"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Colorado Springs, CO 80908
Aaron
Job Details:
10/06/2023
"Removed and replaced components, tested evaporator motor in diagnostics, working well now, unit needs time to cool back down. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Colorado Springs, CO 80908
Aaron
Job Details:
10/06/2023
"F2E2 keypad error code upon arrival, removed and replaced console assembly, programmed and ran unit through DLMS and diagnostic cycles, working well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HFEDBSG/AA
Near Colorado Springs, CO 80917
Jeremy
Job Details:
10/06/2023
Installed all provided parts. Not HASS compatiable. IM working to the best of my knowledge. Asked CX to complete the survey.
We serviced a
SAMSUNG REFRIGERATOR
Model RF24R7201SR/AA
Near Colorado Springs, CO 80910
Jeremy
Job Details:
10/06/2023
Installed all ordered parts. IM working to the best of knowledge.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, CO 80922
Aaron
Job Details:
10/06/2023
"Thermal cutoff shorted out, replaced cutoff and cycling thermostats, tested and working well now. Advised customer of survey."
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ1
Near Colorado Springs, CO 80922
David
Job Details:
10/06/2023
Checked range Cleaned burner portsTested and working good
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW3
Near Colorado Springs, CO 80922
Aaron
Job Details:
10/06/2023
"Water valve solenoid stuck open, removed and replaced valve, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MEDB835DW
Near Fountain, CO 80817
Carlos
Job Details:
10/06/2023
Installed repair kit. ran test op all ok
We serviced a
SAMSUNG RANGE
Model NE58R9560WG/AA
Near Colorado Springs, CO 80921
Brandon
Job Details:
10/06/2023
"Replaced pcb and tested op all ok hass failed and wouldn't send, need to bypass, hass not working on unit connects to app but nothing works thru app"
We serviced a
SAMSUNG REFRIGERATOR
Model RF24FSEDBSR/AA
Near Colorado Springs, CO 80921
Brandon
Job Details:
10/06/2023
"Unit leaking in ice room, 40 c error, removed all ice from ice room, sealed Ice room, all components working to spec hass passed"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW08
Near Grand Junction, CO 81504
James R
Job Details:
10/06/2023
Replaced icemaker and test cycled. Operation is normal. Also found water leaking down behind fill tube at back wall. Sealed thart area ok. customer signed waiver.Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SUBZERO REFRIGERATOR
Model IT-36CI-LH
Near Colorado Springs, CO 80907
Jessie
Job Details:
10/06/2023
Replaced evap fan in freezer again. Unit sounds great all ok
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Grand Junction, CO 81501
James R
Job Details:
10/06/2023
Frz light switch broken. Replaced switch test ok.Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ01
Near Albuquerque, NM 87110
Jason
Job Details:
10/06/2023
Installed Ice maker unit opperation checks ok
We serviced a
GE RANGE - ELECTRIC
Model JS630SF4SS
Near Colorado Springs, CO 80907
Ralph
Job Details:
10/06/2023
installed part and unit checked okay
We serviced a
JENN-AIR COOKTOP
Model JEC3536HB00
Near Grand Junction, CO 81507
James R
Job Details:
10/06/2023
Checked pwr. Removed cover over junction box found black wire not hooked up properly. Reinstalled properly. Put larger wire nuts on black and red wiring. Double checked neutral and grd. were ok. Reinstalled cover. Test operation. Good. Told customer should have a electrician to confirm installation of wiring. Not responsible for anything further. Had customer sign waivers. Customer paid service call. Not covered under warranty. $149.95 auth code. JR3U9NPlease fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model NTW4519JW2
Near Trinidad, CO 81082
James
Job Details:
10/06/2023
found pulley loose causing noise when running. replaced with preordered cam w10721967 & belt w11239857 tested ops all ckok. left litmus. found linoleum tile damaged on arrival (see sd pics) cust is aware.
We serviced a
MAYTAG WASHER
Model MVW6230HC3
Near Rio Rancho, NM 87124
Larry
Job Details:
10/06/2023
CX instruct - Explained operating - Unit is operating as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Albuquerque, NM 87107
Larry
Job Details:
10/06/2023
Installed control and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model KDTM404KPS1
Near Tijeras, NM 87059
Jason
Job Details:
10/06/2023
installed drain pump unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ16
Near Fruita, CO 81521
James R
Job Details:
10/06/2023
Replaced icemaker cycled and filled ok. Checked frz temp -1 good F.F. temp 37 degrees good. Unit is cooling properly. The fans she is hearing are the condenser and F.F. area fans and they sound normal. Compressor sounds normal as well. Also adjusted front feet to the floor so the frig wont roll everytime she gets into it. Unit is operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DRYER
Model WED8000DW4
Near Colorado Springs, CO 80906
Carlos
Job Details:
10/06/2023
"Installed idler pulley, ran test op. All ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Los Lunas, NM 87031
Larry
Job Details:
10/06/2023
Installed valve and tested good - Unit is good to go
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS20
Near Monument, CO 80132
Glenn
Job Details:
10/06/2023
"R & R New Turntable motor, adapter, Shaft & Ring. All OPS Test:OK"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9070SR/AA
Near Elbert, CO 80106
Brandon
Job Details:
10/06/2023
"Replaced parts and charged unit, temps are dropping fridge got down to temp 37, before I left and freezer lowering hass passed"
We serviced a
GE DISHWASHER
Model DDT700SSN5SS
Near Grand Lake, CO 80447
Erik
Job Details:
10/05/2023
installed/testedJOB COMPLETE
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Rifle, CO 81650
James R
Job Details:
10/05/2023
Printed labels. Took pics ready to send in.
We serviced a
SAMSUNG DRYER
Model DVE45T6000W/A3
Near Colorado Springs, CO 80908
Mathew
Job Details:
10/05/2023
Replaced door. Test op all okay. Unit not compatible with hass wireless.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC1
Near Pueblo, CO 81005
David
Job Details:
10/05/2023
Checked dryer Ran through diagnostics no faults Good air flow from dryer Not very good at outside vent Recommend having vent professionaly cleaned
We serviced a
SAMSUNG DISHWASHER
Model DW80K5050US/AA
Near Colorado Springs, CO 80923
Mathew
Job Details:
10/05/2023
"Unit needs a motor assembly. Called Samsung, they said they would send us another ticket to order parts if approved. Need sump assy. DD82-01353A. Did not run hass as unit is inoperable."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Colorado Springs, CO 80920
Mathew
Job Details:
10/05/2023
"Replaced evap and damper motor. Test op, unit working as expected."
We serviced a
SAMSUNG WASHER
Model WF330ANW/XAA 02
Near Colorado Springs, CO 80907
Jeremy
Job Details:
10/05/2023
CX claims to have smelled a burnt smell coming from inside of drum after cycle completed. Stacked unit. I ran rinse and spin cycle. No noticable smells. Drum doesnt spin by hand very easily. I inspected the bearing from the back and it looks good. Im covinced that the inside bearing is going out and heating up creating the smell. The suspension is also bad. The unit is over 10 years old . I told CX a round about price of the repair and cx will probably buy new unit.
We serviced a
GE MICROWAVE
Model JVM3160RF8SS
Near Colorado Springs, CO 80923
Jerimiah
Job Details:
10/05/2023
"Installed replacement control panel assy, unit check ok."
We serviced a
BOSCH WALLOVEN
Model HBL8451UC/02
Near Colorado Springs, CO 80918
Jerimiah
Job Details:
10/05/2023
"Installed replacement gasket. Unit check ok, charged labor as quoted $189.95 CC Auth# 33TT4N"
We serviced a
MAYTAG DRYER
Model MDE9316AYW
Near Colorado Springs, CO 80918
Mathew
Job Details:
10/05/2023
"Replaced burnt out door switch, unit still not working. Power is getting to timer, start switch test ok. Called tech line, they suspect wire harness failure. Part NLA. $179.95 CC Auth# AHTR94"
We serviced a
SAMSUNG DRYER
Model DVE45T3400W/A3
Near Colorado Springs, CO 80907
Brandon
Job Details:
10/05/2023
"Bad thermostat, replaced parts and tested op all checks ok hass passed"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF606ESS01
Near Pueblo, CO 81005
David
Job Details:
10/05/2023
"Checked refrigerator and icemaker Ran diagnostics, ice box fan running, pulled evap cover, evap has full frost pattern, air channels seem to be clear.Freezer was very full and was possibly not fully closing Service fee good for 30 days"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9380SG/AA
Near Colorado Springs, CO 80916
Jeremy
Job Details:
10/05/2023
Installed all provided parts. Ran HASS. IM working to the best of my knowledge. I asked CX to complete the survey.
We serviced a
SPEEDQUEEN DRYER
Model ADEE9RYS177TW01
Near Peyton, CO 80831
Kris
Job Details:
10/05/2023
drum was binding causing error code could not get pic of code. pulled unit apart made sure all parts were not binding. ran test op all ok unit is working to spec at this time.
We serviced a
SAMSUNG REFRIGERATOR
Model RF263TEAESG/AA 04
Near Colorado Springs, CO 80925
James S
Job Details:
10/05/2023
"Replaced ice maker, auger Assembly, T clips, and PCB MAIN. Could not run HAAS.Tested for proper operation."
We serviced a
GE STACK UNIT
Model GUD24ESSJ0WW
Near Colorado Springs, CO 80923
Jessie
Job Details:
10/05/2023
Replaced broken suspension. Unit is not hitting the floor anymore. Unit is going into spin. Transmission is very noisey. If customer wants the repair they will get back to us.
We serviced a
GENERAL ELECTRIC DRYER
Model PTD60EBPR0DG
Near Colorado Springs, CO 80915
Roman
Job Details:
10/05/2023
Not squeaking super loudly but sounds off. Took it apart and the top bearing bracket was not clipped in on either side. Little bits of felt were smushed and not in the grooves they are supposed to be in. Put the dryer back together and did not hear the noise again. If noise comes back recommend to customer letting the dryer break in.
We serviced a
SAMSUNG ELECTRON DISHWASHER
Model DW80R9950UG/AA
Near Monument, CO 80132
Brandon
Job Details:
10/05/2023
"Replaced parts and tested op all ok smart Install passed, installed litmus"
We serviced a
WHIRLPOOL RANGE
Model WGE745C0FS01
Near Pueblo, CO 81008
David
Job Details:
10/05/2023
"Checked range Put into diagnostics, no codes Ran ovens through cycles and oven is going into clean All working good Took pics of the papers they have."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Colorado Springs, CO 80925
Jeremy
Job Details:
10/05/2023
Installed new defrost sensor and evap cover. Refridgerator seem to be operating correctly. CX paid $81.56 Cash
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Colorado Springs, CO 80904
Carlos
Job Details:
10/05/2023
7737493054 Installed compressor and evaporator. Frost patter present when charged. Cx will observe
We serviced a
KITCHENAID DISHWASHER
Model KUDP01ILWH6
Near Colorado Springs, CO 80907
Carlos
Job Details:
10/05/2023
"Installed heater. Ran test op, checked for leaks left leak strip all ok"
We serviced a
WHIRLPOOL DRYER
Model MED5630HC1
Near Colorado Springs, CO 80919
Glenn
Job Details:
10/05/2023
"Not heating.Unit full of lint, Bad Element & ThermostatsElement - WP3387747 $99.68 , Thermostat Kit - 280148 $82.26 , MPS $14.50, Tax $14.92 , Labor $199.95 , Paid in Full $561.26 , Autho# 9X3VHV"
We serviced a
KITCHENAID DISHWASHER
Model KDTM704KPS1
Near Colorado Springs, CO 80908
Kris
Job Details:
10/05/2023
istalled handle ran test op all ok unit is working to spec at this time.
We serviced a
WHIRLPOOL WASHER
Model MVWB765FW3
Near Colorado Springs, CO 80910
Roman
Job Details:
10/05/2023
"Installed new control board and washer lit up. Tested it and it fills, agitates, drains and spins. Washer working great."
We serviced a
BEST DOWNDRAFT VENT
Model D49M36BLS
Near Manitou Springs, CO 80829
Roman
Job Details:
10/05/2023
Installed new control board and made sure the hood and fan both working properly. Vent working great.
We serviced a
BOSCH REFRIGERATOR
Model B36CT80SNS/09
Near Colorado Springs, CO 80906
Roman
Job Details:
10/05/2023
Removed handles and door gasket and installed it on the new door. Made sure fridge door is closing properly. Door working great.
We serviced a
BOSCH DISHWASHER
Model SHV65P03UC/63
Near Colorado Springs, CO 80918
Jessie
Job Details:
10/05/2023
Replaced valve. Tested unit for leaks.
We serviced a
SAMSUNG DRYER
Model DVE50R5200W/A3
Near Colorado Springs, CO 80924
Brandon
Job Details:
10/05/2023
Replaced moving parts and tested op all ok hass passed
We serviced a
DACOR WALL OVEN ELECTR
Model RO230S
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
10/05/2023
"U20 error over temp on upper oven, techline says relay board needs replacing. Labor will be $199.95 upon return service. Board is not available and Cust will look into finding part himself. Charging service call $149.00 CK Auth# P4C34A chk#11219DE81-05671A relay board NLA"
We serviced a
THERMADOR INDUCTION COOKTO
Model CIT36YWBB/01
Near Larkspur, CO 80118
Jessie
Job Details:
10/05/2023
Replaced top. Looks good all ok
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS1
Near Elbert, CO 80106
Aaron
Job Details:
10/05/2023
"Circulation motor is weak, removed and replaced sump assembly, corrected unit install mounting tabs, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
JENN-AIR REFRIGERATOR
Model JF42NXFXDE02
Near Colorado Springs, CO 80906
Carlos
Job Details:
10/05/2023
Installed LED lights. All ok.
We serviced a
JENN-AIR WALLOVEN
Model JJW3430DP02
Near Larkspur, CO 80118
Glenn
Job Details:
10/05/2023
"Install New Console, Program to model. All OPS Test:OKPaid remaining SC Fee $149.95 + MPS $14.50 + Labor $209.95 = $374.40 , Autho# AW3L44"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS04
Near Monument, CO 80132
Glenn
Job Details:
10/05/2023
"Customer indicates, that water had began to collect around bucket seal to IM & around / under IM face. Also noticed frost buildup in Freezer top drawer. They since turned off the ice maker. No Frost Buildup on either evap. Water hold test on flapper > Failed.Test 56 > No IM Error Codes, Harvest > Pass , Fill Test > Pass. No excessive water? Bucket door seal looks ok, All Door seals < OK, All Fans working. Techline: Possible Bad IM Fan Motor - W10846539 $200.62 + Tax , Most likely freezer door did not close 100% causing frost prob. All OPS Test:OK at this time. Leaving Deli UI disconnected for now. customer will continue to monitor. Placed a cup under dispenser to remind customer to check its status. SR# 7737491992"
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GWH0
Near Colorado Springs, CO 80917
Glenn
Job Details:
10/05/2023
"Bad Wash motor assy.Sump & Motor Assy - W11665769 $217.94 , Tax $17.87 , MPS $14.50 , Labor $319.95 , Declined Estimate. Paid SC fee of $129.95 , Check #4968 , Autho#3WHTUL"
We serviced a
GE DRYER
Model GTD86ESSJ0WS
Near Colorado Springs, CO 80924
Kris
Job Details:
10/05/2023
cleaned out unit for cx.
We serviced a
KITCHENAID REFRIGERATOR
Model WRF555SDFZ15
Near Calhan, CO 80808
Aaron
Job Details:
10/05/2023
"Removed and replaced RH RC door. No scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF23R6201SR/AA 53
Near Colorado Springs, CO 80908
Brandon
Job Details:
10/05/2023
"Replaced parts and tested op all checks ok, ice maker cycled ,sealed ice room"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ00
Near Carbondale, CO 81623
James R
Job Details:
10/05/2023
Replaced all lights per S191AQ Operation normal. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
KITCHENAID WALLOVEN
Model KEMS307GBS0
Near Colorado Springs, CO 80918
Glenn
Job Details:
10/05/2023
"Install New Door Hinges. Allowed customer to clean glass panes during repair process. All OPS Test:OKDoor now staying closed on its own, and lights now turns off.Customer had to leave in a hurry, unable to sign after completion."
We serviced a
MIELE RANGE
Model HR1124-3G
Near Colorado Springs, CO 80923
Kris
Job Details:
10/05/2023
ran test op found ignitor was shorted reseated ran test op all ok unit is working to spec at this time.
We serviced a
WHIRLPOOL RANGE
Model WFE515S0JS3
Near Carbondale, CO 81623
James R
Job Details:
10/05/2023
checked unit per service pointr W11525530Removed cover over terminal block. Unplugged unit checked cord for correct installation. Ok. checked L1 L2 for continuity to grd and neutral open circuit good. Polarity is correct. Pwr coming in is 214 vac good. doest pop breaker when plugged in but not on. turned on bake on 9.3 amp draw. Broil 13.2 213 vac with unit on bake. good.Bake element 23.5 ohms good and not to grd. Broil 16.7 ohms good and is not to grd. customer signed waiver. Left infomation with customer on findings of unit and that it is operating as should. Also contact information of the breaker. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Albuquerque, NM 87110
Jason
Job Details:
10/05/2023
installed valve unit opperation checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW2
Near Cañon City, CO 81212
James
Job Details:
10/05/2023
Installed ordered parts tested spin and agitate both test good. could not test water because unit in garage with no supply. all mech functions test good
We serviced a
COVE DISHWASHER
Model DW2450
Near Cañon City, CO 81212
James
Job Details:
10/05/2023
installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL WASHER
Model MHWE300VW12
Near Carbondale, CO 81623
James R
Job Details:
10/05/2023
Replaced bellows. Test run checked for a leak none. Customer paid service call $149.95 auth code 3R3EM3Customer signed waivers. Put leak board under unit. Please fill out whirlpool tech satisfaction survedy. Thank You.
We serviced a
BOSCH FRENCH DOOR REFR
Model B36FD50SNS/01
Near Cañon City, CO 81212
James
Job Details:
10/05/2023
found rear panel not fully seated causing ice to buildup near evap fan. cleared ice and tested. Ops test good.
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Glenwood Springs, CO 81601
James R
Job Details:
10/05/2023
Could hear something in the control. Replace ok. Also the belt was loose could hear a squeak. Replaced and test ok. Could hear rattling Tech service pointer W11695259 adjusted bottom and side of panels so contact good of rear panel ran in spin ok. Also it is normal for drain hose to shake during the spin cycle it is attached to the back panel and tub so as the tub shake so will hose. Put straps on to minimise noise. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.; used 1 WPW10006384 (Belt (Washer)) from stock
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Glenwood Springs, CO 81601
James R
Job Details:
10/05/2023
Put into drain could here nothing pump not coming on. Removed unit and replaced drain pump. Reinstalled unit and test in service diagnostics. Cleared F9E1 code. Went thru just fine no error codes when finished. Put a leak board under unit. Operation normal. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Albuquerque, NM 87109
Jason
Job Details:
10/05/2023
installed capacitor unit checks ok
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Rifle, CO 81650
James R
Job Details:
10/05/2023
Put into drain and spin not shifting and just hums when agitates or spins. Replaced actuator and capacitor. Test again. Operation is normal. Operating as should. Customer signed waiver. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Albuquerque, NM 87112
Jason
Job Details:
10/05/2023
"installed diffuser, unit opperation checks ok"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Albuquerque, NM 87112
Jason
Job Details:
10/05/2023
installed strike also found rotor had come loose. tightened rotor bolt up unit checks ok
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Albuquerque, NM 87111
Jason
Job Details:
10/05/2023
checked unit found cam was worn installed cam unit checks ok; used 1 w10721967 (cam) from stock
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA
Near Penrose, CO 81240
James
Job Details:
10/05/2023
installed ordered parts tested ops all ckok ran hass and sent report
We serviced a
KITCHENAID DISHWASHER
Model KDFE104KPS0
Near Grand Lake, CO 80447
Antonio
Job Details:
10/05/2023
Installed new door seal unit tested good
We serviced a
GE REFRIGERATOR/TOP
Model GDE21EGKURWW
Near Colorado Springs, CO 80916
Roman
Job Details:
10/05/2023
"Showed up and they had a bin full of ice, had another guy come out through warranty, and he did some things to the fridge. Cx found a part in the bin and it doesnt look like anything to do with an ice maker. Did not install ice maker."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Fraser, CO 80442
Antonio
Job Details:
10/05/2023
adjusted the condencer from vibrating unit tested good
We serviced a
KITCHENAID REFRIGERATOR
Model KSSS48QHB00
Near Woodland Park, CO 80863
Ralph
Job Details:
10/05/2023
made an adjustment to the fan blade cust to monitor
We serviced a
WOLF WALL OVEN
Model SO3050TE/S/T
Near Woodland Park, CO 80863
Ralph
Job Details:
10/05/2023
"replaced cooling fan and seems to have fixed the issue, board was not correct board...Amy 1 hr on this job please"
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Albuquerque, NM 87121
Larry
Job Details:
10/05/2023
Installed control and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW2
Near Albuquerque, NM 87120
Larry
Job Details:
10/05/2023
Could not duplicate issue - Unit is operating as designed - Informed cx of potential charges for next visit
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Albuquerque, NM 87114
Larry
Job Details:
10/05/2023
Replaced console and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MHWE251YG00
Near Albuquerque, NM 87114
Larry
Job Details:
10/05/2023
CX complaint - Washer not draining - Inspected unit and found debris in the drain pump - Removed debris and tested good - Unit is good to go
We serviced a
GE DISHWASHER
Model DDT700SSN5SS
Near Grand Lake, CO 80447
Erik
Job Details:
10/05/2023
installed/testedJOB COMPLETE
We serviced a
THERMADOR BUILT-IN REFRIGE
Model T24IR905SP/10
Near Fraser, CO 80442
Erik
Job Details:
10/05/2023
replace right side shelf support/ test: GOODJOB COMPLETE
We serviced a
GE DRYER
Model GFD55GSSN1WW
Near Fraser, CO 80442
Erik
Job Details:
10/05/2023
install parts/ test: ignitor-checkmotor-checksensor-check (proper cut-out)JOB COMPLETE
We serviced a
WHIRLPOOL VENT HOODS
Model JXW9036HP4
Near Florissant, CO 80816
Ralph
Job Details:
10/05/2023
installed parts and unit checked okay
We serviced a
VIKING REFRIGERATOR
Model VCSB5423SS01
Near Colorado Springs, CO 80921
Kris
Job Details:
10/04/2023
unit has sealed system issue. all fans are working and compressor is running not cooling. either has a leak or bad compressor.
We serviced a
GAGGENAU FREEZER
Model KRF0R63701/13
Near Colorado Springs, CO 80921
Kris
Job Details:
10/04/2023
ran test op found bad start device replaced watched temp drop all ok cx will monitor
We serviced a
WHIRLPOOL RANGE
Model WFE550S0LZ2
Near Colorado Springs, CO 80925
Roman
Job Details:
10/04/2023
Installed new control and it will not turn on. Checked voltage to it and its getting 120 v to the board. Terminal is reading 240V but only getting 23V on black and white wires. Call tech and they said it is a outlet issue with the neutral recommend calling an electrician
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Monument, CO 80132
Glenn
Job Details:
10/04/2023
"Install New Console w/ harness, All OPS Test:OK"