We serviced a
GE WASHER
Model GTW465AS9WW
Near Colorado Springs, Colorado 80918
Earl
Job Details:
07/16/2026
Custo\nMers complaint unit will not go into a spin and spin the water out arrived.And I found a ground wire loose getting caught in the belt.I reattached the ground test.The unit is offering property at this time
We serviced a
LG WASHER
Model WM8900HBA
Near Colorado Springs, Colorado 80906
Charles
Job Details:
07/16/2026
"Order door boot MDS47123631, Service fee 149.95, Labor $209.95, MPS $18.50, Part $283.97, Tax 23.29, Total $685.66, declined estimate paid service fee check #3091 $149.95 autho L993FN"
We serviced a
KITCHENAID RANGE
Model KFGD500ESS04
Near Santa Fe, New Mexico 87508
Tye
Job Details:
07/16/2026
Arrived and cx complaint of lower oven not heating. Found failed igniter. Replaced igniter and tested oven. Unit is functioning now as designed. Informed cx of review.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Granby, Colorado 80446
Antonio
Job Details:
07/16/2026
Installed new compressior and dier then charged unit with r600. Fridge is holding at 36 degrees and freezer is at -1 deg unit is working properly.also advised cx of whlp survey
We serviced a
AMANA WASHER
Model NTW4605EW0
Near Pueblo, Colorado 81004
James
Job Details:
07/16/2026
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ1
Near Santa Fe, New Mexico 87508
Tye
Job Details:
07/16/2026
Arrived and cx complaint of not cleaning right. Informed cx of soap options. Informed cx of cleaning filters. Informed cx of review.
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Santa Fe, New Mexico 87505
Tye
Job Details:
07/16/2026
Arrived and cx complaint of not draining right. Found drain hose too long. Took extra hose off. Tested unit. Washer is working as designed.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Santa Fe, New Mexico 87506
Tye
Job Details:
07/16/2026
Arrived and cx complaint of not cleaning dishes. Found failed motor assembly. Installed new motor and dispenser assembly. Informed cx of review.
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Grand Lake, Colorado 80447
Antonio
Job Details:
07/16/2026
Installed new acu then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
BOSCH SPEED OVEN
Model HMC54151UC/07
Near Fraser, Colorado 80442
Erik
Job Details:
07/16/2026
Install turntable test pass job complete
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFFU16F2VV
Near Granby, Colorado 80446
Erik
Job Details:
07/16/2026
"Manually, defrost freezer door too low hinge. Not adjustable need washers to prop Door to proper height.I stall lower hinge with washers as shims, door seals completely now, also added petroleum jelly for extra suctionJob complete"
We serviced a
GE DRYER
Model GTX33EASK1WW
Near Carbondale, Colorado 81623
Sean
Job Details:
07/16/2026
Verified the unit information customer signed disclaimer.Checked the unit and found the start switch assembly was pushed through the control housing.Removed the control panel and reattached the start switch.Reassembled the unit and installed the new start button.Fixed a kink in the exhaust vent. Tested the unit good.Thank you.Please go online and fill out a technician survey.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM11
Near Santa Fe, New Mexico 87507
Jason
Job Details:
07/16/2026
Installed compressor pressures and heat exchange check ok. unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DRYER
Model WED6620HC1
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
07/16/2026
Unit will need element replacement. Replace element. Clean inside of cabinet. Test op. Unit working as expected. $506.18 CK Auth# EKM9WT- QUOTE 7/16/2026PART: Part wp3387747 (shipping incl.) $118.10LABOR: Dryer Heating Element (no glass door) (Whirlpool ? LOW end ? Tier 2) $209.95SERVICE CALL $149.95MPS $18.50SALES TAX (CO Springs rate ? parts only ? 8.2%) $9.68TOTAL $506.18
We serviced a
WHIRLPOOL DRYER
Model WED5050LW1
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
07/16/2026
Replace bad element and replace cut offs. Test op. Breaker was tripped from previous issue. Re set breaker. 120 v supplied from wall. Dryer needs 240 to run heater. One leg of power is missing. Recommend house electrical be inspected.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Hot Sulphur Springs, Colorado 80451
Antonio
Job Details:
07/16/2026
Installed drawer and showed cx how to install water filter and reset water filter settings
We serviced a
SAMSUNG STACK UNIT
Model WH46DBH500EVA3
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
07/16/2026
Replaced testing element and tested operation all checks ok hass passed
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6600APAA
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
07/16/2026
"Removed all ice from evaporator and replaced defrost sensor all checks ok, labor paid $239.95 CC Auth# 4Y3ME9"
We serviced a
MONOGRAM BI REFRIGERATOR
Model ZIS480NMC
Near Colorado Springs, Colorado 80926
Ralph
Job Details:
07/16/2026
"replaced part and unit checked okay, cust to monitor...autho no. K4RK9M"
We serviced a
GE DRYER
Model GTD48EASW0WB
Near Rifle, Colorado 81650
Sean
Job Details:
07/16/2026
Customer had the neighbors let me in and sign the ticket.Removed the old button and installed the new button .Tested the unit good.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AFL
Near Pueblo, Colorado 81001
David
Job Details:
07/16/2026
"Installed fan motor assembly, it is running with normal sounds."
We serviced a
MAYTAG DRYER
Model MGD5630HW4
Near Aspen, Colorado 81611
James R
Job Details:
07/16/2026
Signed disclaimer. Tore apart and replaced hi limit thermostat. Re-assembled and run unit timed dry hi temp. Cycles between 155 and 125 ok. Also on auto dry cycles the sensors sense the dampness of the cloths. Cycle will continute to run according to the dryness setting selected. Operating as designed. Do not over load unit cloths need to be able to tumble so air can circultate across cloths.
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Colorado Springs, Colorado 80922
Mathew
Job Details:
07/16/2026
Replace leaking lokring connector. Install stub and drier. Nitrogen check at 350 psi for 15 minutes. No leaks found. Pull into deep vac. Charge to spec. Monitor temps and pressures. All okay.
We serviced a
MAYTAG WASHER
Model MTW7200RF1
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
07/16/2026
"Inspected unit once more, no leaks coming from the washer, water is still building in standpipe, unable to properly drain once water reaches the drain hose. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVW7230HC1
Near Albuquerque, New Mexico 87120
Larry
Job Details:
07/16/2026
Cx complaint - Washer making loud noise - inspected unit and found the suspension very loose - Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRTX5419SW00
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
07/16/2026
"Unit has a defrost drain issue, cleared ice and tested, working well now. Advised customer of situation and survey."
We serviced a
GE WASHER
Model GTW335ASN2WW
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
07/16/2026
"Lid lock error, water accessibility error, out of balance error codes in diagnostics, plastic lodged in belt guard and rubbing against pulley, corrected and tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED5KVEXVB00
Near Albuquerque, New Mexico 87121
Larry
Job Details:
07/16/2026
Cx complaint - Freezer has ice on the bottom and it is leaking onto the floor - Inspected unit and found the drain tube clogged causing water to back up and freeze during defrost - Cleared tube and tested good - Unit is good to go - Survey mentioned
We serviced a
LG REFRIGERATOR
Model LFXS26973S1/10
Near Colorado Springs, Colorado 80903
Brandon
Job Details:
07/16/2026
Replaced ice fan and tested operation all checks ok
We serviced a
KITCHENAID RANGE
Model KCGS556ESS06
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
07/16/2026
"Knob Bezel is loose, burners are lighting and working welln needs bezels, adjusted valve for simmer, discussed situation with techline, recommend customer to contact customer service for further assistance. Advised customer of situation and survey. Case number 24235091"
We serviced a
GE WASHER
Model GFW650SPN1SN
Near Granby, Colorado 80446
Erik
Job Details:
07/16/2026
"Install inverter board provided by customer, apply firmware update via connecting to smart hq serviceTest:pass. Job completeBill sent via iwallet"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS07
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
07/16/2026
"Right RC door lower, customer complains of left door popping open right door when closing, leveled doors and unit, left RC door has ice bin and extra weight, recommend guiding door closed, closing left door then right, discussed situation with techline and documented. Advised customer of situation and survey. Case number 24234793"
We serviced a
MAYTAG DRYER
Model MEDX600XW0
Near Colorado Springs, Colorado 80910
Earl
Job Details:
07/16/2026
Customers complaint unit making sound.I arrived and found that the body was creaking.We adjusted the frame a little bit and it stopped.Making the noise unit is operating properly at this time
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near La Pine, Oregon 97739
Levi
Job Details:
07/16/2026
Replaced the control board and tested all checks okay and performed recalibration cycle.
We serviced a
MAYTAG WASHER
Model MTW6205RF0
Near Colorado Springs, Colorado 80920
Aaron
Job Details:
07/16/2026
"Removed and replaced UI console, programmed and tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID DISHWASHER
Model KDTS724SPS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
07/16/2026
"Power at junction box not secure, corrected and tested unit through diagnostics, working well now, verified by customer. Advised customer of situation and survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5300SRAA
Near Carlton, Oregon 97111
Jesse
Job Details:
07/15/2026
"July 15 9:01 JG left vm eta 1.45 hour drive , also left reminder to make sure unit is an accessible place for service .Client has difficulty moving unit , utilized scuff pad & blankets . Replaced and tested parts. Verified cooling"
We serviced a
WOLF COFFEE MACHINE
Model EC2450TE/S
Near Hillsboro, Oregon 97123
Austin
Job Details:
07/15/2026
7/15/26 BA: removed and replaced infuser assembly and slider. Tested unit by making a cup of coffee and found no further issues. Service is complete
We serviced a
BOSCH DISHWASHER
Model SHS43CF5N/27
Near Willamina, Oregon 97396
Austin
Job Details:
07/15/2026
7/15/26 BA: removed and replaced water inlet system on The side of the dishwasher. Tested unit for any leaks and found none while testing after part replacement. Reinstalled and leveled unit. Service is complete
We serviced a
SAMSUNG WASHER
Model WF45T6000AW
Near Silverton, Oregon 97381
Austin
Job Details:
07/15/2026
7/14/26 BA: CX error code SUD on display even after running a clean cycle. Tech checked the drain filter and drain hose. Upon inspection the tech found the pressure switch hose to be detached from the switch. Tech was able to reattach the hose through the front of the machine. Reset the unit and error code has gone away. Ran test cycle for any leaks and found none while further issues. Service complete
We serviced a
BOSCH REFRIGERATOR
Model B36FD10ENS
Near Silverton, Oregon 97381
Austin
Job Details:
07/15/2026
7/15/26 BA: Cx CB unit is developing frost in the freezer and door hard to close. Tech looked over the unit and found a blockage in the drain cap behind the unit. Tech cleared the debris and put unit into a defrost. Unit is defrosting normally and no leaks present inside the machine. Tested ice and water functions and found no issues as well. Service complete
We serviced a
ELECTROLUX DRYER
Model ELFE7437AG0
Near Cave Junction, Oregon 97523
Chris
Job Details:
07/15/2026
Replaced all parts listed and tested.
We serviced a
MAYTAG WASHER
Model MVWX655DW2
Near Roseburg, Oregon 97471
Chris
Job Details:
07/15/2026
Replaced the drive hub and agitater. Ran a test cycle and passed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3136SZ00
Near Florissant, Colorado 80816
David
Job Details:
07/15/2026
"Replaced valve and fill tube, installed stops. Ran icemaker test to fill, cx to monitor."
We serviced a
LG REFRIGERATOR
Model LRMVS3006D/01
Near Peyton, Colorado 80831
Earl
Job Details:
07/15/2026
Install the ice maker in turn it on unit is operating properly at this time
We serviced a
SAMSUNG WASHER
Model WF90F53ADSA5
Near Monument, Colorado 80132
Brandon
Job Details:
07/15/2026
"Found bad gasket on pump, replaced pump and tested operation all checks ok hass passed"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
07/15/2026
Installed heating element ran tests all ok. Cx needs to have vents cleaned
We serviced a
MAYTAG DRYER
Model MEDX655DW1
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
07/15/2026
Unit failed air flow tests all ok cx needs to have vents cleaned
We serviced a
LG REFRIGERATOR
Model LRMVS3006D/01
Near Peyton, Colorado 80831
Aaron
Job Details:
07/15/2026
"Helper for ER, unit needs time to cool. Working well now."
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Belen, New Mexico 87002
Larry
Job Details:
07/15/2026
Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
JENN-AIR MICROWAVE
Model WMH31017HS09
Near Bend, Oregon 97702
Levi
Job Details:
07/15/2026
Found some screws on the bottom plate that were a little on the loose side allowing unit to vibrate during use. Tying up the screws and everything seems to be good and testing right now.
We serviced a
GE DISHWASHER
Model CDT858P2V6S1
Near Montrose, Colorado 81401
Sean
Job Details:
07/15/2026
Verified information customer signed disclaimer.Checked the unit and found that it was low on the front right side. Removed the bottom panel and checked the legs. All the legs are extended all the way.I adjusted the legs so the unit is in the proper alignment.Checked the door gasket it is in good shape .Found the bottom rack was bent out on the sides and rubbing the gasket. I adjusted the lower rack reassembled the unit and tested. The unit is leak free. Found the unit has play and can be slid back on the bottom of the unit putting the back end of the unit higher than the front and causing it to drip water from door.Also found that the counter's are not plumb they are leaning in words at the top. Unit can not be level with the drawers.The unit needs to have the mounting screws put in the sides of the unit to prevent the unit from shifting around .
We serviced a
KITCHENAID REFRIGERATOR
Model WGE759C0FS05
Near Wolcott, Colorado 81655
Antonio
Job Details:
07/15/2026
Found condencer clogged with dust and dog hair causing unit to over heat clean condencer unit is working properly $229.95 CC Auth# LJ4JV3
We serviced a
KITCHENAID DISHWASHER
Model KUDE70FXBL5
Near Beaver Creek, Colorado 81620
Antonio
Job Details:
07/15/2026
Start dishwasher check for error codes there was none present recommending cx clean filter and use all fresh tablets $229.95 CC Auth# W44N3A
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Grand Junction, Colorado 81505
Clint
Job Details:
07/15/2026
Customer signed disclaimer and stated unit wont drain .Bobby had pulled it out and saw nothing in the pump.Pulled drain line off and couldn't blow through it.At the end of the drain line there was build up at the 90 degree pvc pipe they had put in the end. I removed that and put the drain line directly into the garbage disposal. Unit is draining and washing perfectly now now leaks detected.PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KBS02
Near Fruita, Colorado 81521
James R
Job Details:
07/15/2026
"Signed disclaimer. Evac system. Removed compressor and drier. Use all parts listed. Replaced compressor, drier overload relay. etc. Pressure tested system to 240 psi and took pic. Bubble tested joints no leaks took pics. Evac system and re-charge lo side -6 high side 75psiUnit is cooling. Please fill out tech satisfaction survey. Thank You."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFC5236RZ00
Near Colorado Springs, Colorado 80919
Torrey
Job Details:
07/15/2026
Called safety and told them the issue. Lady was sitting in the living room when the dispenser cane on by itself and sprayed water on the floor. She came in and slipped and fell. The water is currently off. Safety gave a case number and said to call tech support.Case number 24133750Called tech support. They say new ui and all dispenser parts.Case number 24213444Was told to call safety back. They said to close out the file. Don't even figure out parts.
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LZ2
Near Colorado Springs, Colorado 80918
Torrey
Job Details:
07/15/2026
"Tech removed and replaced the console. All burners, bake, and broil tested good."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Colorado Springs, Colorado 80918
Torrey
Job Details:
07/15/2026
Removed and replaced UI and mainboard. Tested good.
We serviced a
SAMSUNG REFRIGERATOR
Model RF25C5551SR/AA
Near Colorado Springs, Colorado 80905
Mathew
Job Details:
07/15/2026
Replace evap assy. Test op all okay.
We serviced a
GE RANGE
Model GRF400SV1WW
Near Prineville, Oregon 97754
Richard
Job Details:
07/15/2026
Installed new drawer assembly all tested fine at this time
We serviced a
GE RANGE
Model PSS93YP9FS
Near Madras, Oregon 97741
Richard
Job Details:
07/15/2026
Installed new controls relay boards cycle tested unit all tested fine at this time
We serviced a
GE RANGE
Model JGS760SP4SS
Near Madras, Oregon 97741
Richard
Job Details:
07/15/2026
installed new valve cycle tested unit all tested fine at time of repair
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC236SPS02
Near Delta, Colorado 81416
Sean
Job Details:
07/15/2026
Verified information customer signed disclaimer.Opened the package and checked the part good.Opened the freezer and removed the old ice maker.Installed the new ice maker and turned it on.Informed the customer that the unit could take 24 hours to produce ice.Tested the unit good.Thank you
We serviced a
GE RANGE
Model JBS86SP6SS
Near Grand Junction, Colorado 81507
Sean
Job Details:
07/15/2026
Verified information customer signed disclaimer.Unplugged the unit and removed the glass top. Unhooked the 5.5 inch element and installed the new one. Reassembled the unit and tested the light went off .Started the 12' element to test the hot surface light and it came on. Watched till the light went back off.The unit tested good.Thank you.
We serviced a
SAMSUNG RANGE
Model NSE6DG8100SRAA
Near Roseburg, Oregon 97470
Chris
Job Details:
07/15/2026
"Replaced the control board, temperature sensor, and bake element. Tested. No HASS port available."
We serviced a
WOLF RANGE
Model GR304-LP
Near Sisters, Oregon 97759
Richard
Job Details:
07/15/2026
Installed new switches cycle tested unit all tested fine at this time
We serviced a
PROFILE RANGE
Model PGS930YP1FS
Near Divide, Colorado 80814
Charles
Job Details:
07/15/2026
"Open bake igniter, replaced igniter 12400035, Service fee $249.95 prepaid, Labor $229.95, MPS $18.50, Part $85.16, Tax $4.60, Total $588.16, balance due $338.21 paid autho KYW9F3"
We serviced a
MIELE WASHING MACHINE
Model WXR860
Near Vail, Colorado 81657
Erik
Job Details:
07/15/2026
Perform spin teat with live load from cxCould not reproduce walking - balanced load Suspect towels and bed linens and loading technique for walking
We serviced a
MAYTAG WASHER
Model MTW6200RW0
Near Grand Junction, Colorado 81504
James R
Job Details:
07/15/2026
Signed disclaimer. Replaced basket installed new screw and then sensor. Did a DLMS calibration and a service diagnostics test. No error codes came up. Also did a hi speed spin unit is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5201SR/AA
Near Monument, Colorado 80132
Brandon
Job Details:
07/15/2026
replaced door and tested operation all checks ok hass passed
We serviced a
WHIRLPOOL WASHER
Model WTW4950HW3
Near Pueblo West, Colorado 81007
James
Job Details:
07/15/2026
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL WALL OVEN
Model WOEC7030PZ01
Near Grand Junction, Colorado 81507
Clint
Job Details:
07/15/2026
Customer signed disclaimer and recieved parts ordered. Had to pull unit out from the wall to remove control panel. I only pulled it out about 5 inches removed the 2 screws replaced the board and put unit back in.Customer will watch and see if the display works properly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL RANGE
Model WFGS5030RZ0
Near Grand Junction, Colorado 81503
Clint
Job Details:
07/15/2026
"Customer signed disclaimer and recieved parts ordered. Installed new ignitor ,harness,and spark module. Unit ignited on first try and cycled perfectly. PLEASE TAKE TECH SURVEY THANKS.CLINT."
We serviced a
ELECTROLUX RANGE
Model ECCG3672AS
Near Colorado Springs, Colorado 80908
Earl
Job Details:
07/15/2026
I install the face plate and the grill and tested. It unit is operating properly at this time.
We serviced a
SUB ZERO REFRIGERATOR
Model DET3650CI/L
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
07/15/2026
installed listed parts and unit checked okay
We serviced a
KITCHENAID DISHWASHER
Model KDTS464SPS0
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
07/15/2026
"Door latch system is shorted out, removed and replaced, tested unit through diagnostics, working well now, verified by customer. Advised customer of situation and survey."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, Colorado 80920
Torrey
Job Details:
07/15/2026
Unit cycles heat from 140 to 220. Normal since there is a calculated 22 ft of ducting. Door gets hot because there is zero insulation in the door.
We serviced a
JENNAIR WALL OVEN
Model JMW2430IL02
Near Monument, Colorado 80132
Torrey
Job Details:
07/15/2026
Tech removed console and added spot welds of JBweld using the Whirlpool kit. Used a hair dryer to help the glue setup quicker for about 20 minutes. Reinstalled the console and asked the owner to not turn on the breaker for 24 hours to allow the glue to cure. Asked her to report back on the success of the repair. Cx called office to pay. I heard her over speaker phoneAuth code 4CMVH3 $219.95
We serviced a
WOLF RANGE
Model GR484DG-LP
Near Woodland Park, Colorado 80863
Charles
Job Details:
07/15/2026
"Replaced left & right griddle direct spark board, tested both griddles ignited"
We serviced a
JENNAIR RANGE
Model JGCP436HL02
Near Colorado Springs, Colorado 80908
Torrey
Job Details:
07/15/2026
Removed and replaced front panel. No scratches or dents. Cx approved. All burners test good. Owner took a picture of the model Serial as tag could not be detached.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS00
Near Albuquerque, New Mexico 87120
Tye
Job Details:
07/15/2026
Arrived and removed failed icemaker. Installed new icemaker. Informed cx of review.
We serviced a
KITCHENAID DISHWASHER
Model KDTS324SPS0
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
07/15/2026
"Water inlet assembly connection not fully secure, corrected and tested unit through diagnostics, working well now, no leaks. Advised customer of situation and survey."
We serviced a
JENN-AIR DISHWASHER
Model JDAF3924RX0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
07/15/2026
"Removed and replaced control and heat pump, tested unit through diagnostics, intermittently tripping in test 6, 15.0 resistance for heater, not grounded, discussed situation with techline, not grounded and pulling 3.6 and 4.4amps to the heater, unit does not trip when plugged into outlet for the other dishwasher. Advised customer of situation and survey. Case number 24218237"
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Albuquerque, New Mexico 87108
Jason
Job Details:
07/15/2026
Installed hub and tub ring ran spin cycle to test operation unit operation checkso ok. spoke to cx about review
We serviced a
MAYTAG DRYER
Model MED6630HW0
Near Albuquerque, New Mexico 87110
Jason
Job Details:
07/15/2026
Checked unit found element open. installed element ran timed dry cycle unit operation checks ok spoke to cx about review; used 1 WP3387747 (element) from stock
We serviced a
THERMADOR BI FREEZER
Model T30IF70NSP/09
Near Manitou Springs, Colorado 80829
Charles
Job Details:
07/15/2026
"Freezer 40 degrees, fan not running, upper panel full of ice, tested heater in diagnostic, drain frozen. Defrosted several inches of ice to pull evaporator cover to access drain Service fee $ 169.95, Labor $259.95, Total $$429.90 sent link for payment to owner, never received confirmation of payment. DID NOT COLLECT $, owner never signed and approved SEND BILL TO CUSTOMER"
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Fountain, Colorado 80817
David
Job Details:
07/15/2026
"Not working upon arrival, replaced control and UI. Tested and is operating as designed. Cx"
We serviced a
WOLF RANGE
Model n/a
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
07/15/2026
showed cust how to clean her ignitors and bases...autho no. w339rk
We serviced a
KITCHENAID MICROWAVE OVEN
Model KMBS730SPS00
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
07/15/2026
"Dent lower right of door, removed and replaced, no scratches or dents, verified by customer. Advised customer of situation and survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5300SR
Near Woodburn, Oregon 97071
Jesse
Job Details:
07/15/2026
"July 15 JG 1:43 PM, contacted client and informed her ETA 60 minutesConcern : left side fridge door was not closing properly due to mullion flap out of alignment. Machine fault not user error or install issue. Adjusted and re secured flap. Tested multiple times and had client test it to ensure they were happy they are."
We serviced a
SUB ZERO REFRIGERATOR
Model 590
Near Sherwood, Oregon 97140
Austin
Job Details:
07/15/2026
7/15/26 BA: removed and replaced master switch assembly with jumper kit. Unit is now powered on and compressors are running. Told Cx to wait up to 24hrs for proper temps and maybe longer for ice production. Condenser unit serviced as well. Service complete$229.95 CC Auth# U949AV
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Albuquerque, New Mexico 87109
Jason
Job Details:
07/15/2026
Checked unit found clip had come off of drain pump impeller and stopped impeller from rotating. removed clip ran cycle to test operation unit operation checks ok. spoke to cx about review
We serviced a
KITCHENAID WALL OVEN
Model KOEC630SPS00
Near Albuquerque, New Mexico 87111
Jason
Job Details:
07/15/2026
installed parts and adjusted fitment as much as possible. ran a few heat cycles unit operation checks ok at this time. cx to monitor if noise comes back. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
07/15/2026
Arrived anf cx complaint of not filling Called techline. Informed me of extra power feature. Washer is functioning now as designed. Case #24214154.
We serviced a
AMANA DRYER
Model NED4655EW1
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
07/15/2026
Arrived and cx complaint of not heating. Found failed thermal overload. Replaced and vhecked dtyer operation. Unit is functioning now as designed. Informed cx of review. ; used 1 Wp8573713 (Thermostat) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ14
Near Ashland, Oregon 97520
Kyle
Job Details:
07/15/2026
"Doors slightly miss aligned, fresh food side higher than freezer side to account for food and weight in door of fresh food. When adding food doors should line up. Called customer and advised them that after the load fresh food and doors are still miss aligned, give us a call to come put and adjust after weight is on doors. Unit is operating as intended."
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near Medford, Oregon 97504
Kyle
Job Details:
07/15/2026
Customer stated washer was not filling with water. Changed cycle to quick wash and tested. Unit is operating as intended.
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Medford, Oregon 97504
Kyle
Job Details:
07/15/2026
"Replaced dispenser assembly cover and tested, unit operating as intended. Ran HASS unit passed, submitted report."
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Pueblo, Colorado 81008
James
Job Details:
07/15/2026
Found loose wire at moisture sensor. Secured and tested ops ckok