We serviced a
AMANA WASHER
Model NTW4519JW2
Near Albuquerque, NM 87123
Jason
Job Details: 08/21/2023
installed inlet assy unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW07
Near Albuquerque, NM 87122
Jason
Job Details: 08/21/2023
sealed cabinet to liner gaps unit checks ok
We serviced a
GE RANGE
Model JB256DM3WW
Near Snowmass, CO 81654
Erik
Job Details: 08/21/2023
BURNER CONNECTION FELL OUT OF HARNESS (durring shipping/install) *SEE QUICK PICSCONNECT HARNESS TO BURNER AND SECURE/TEST:GOODJOB COMPLETE
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0AS04
Near Albuquerque, NM 87111
Jason
Job Details: 08/21/2023
installed mag tube and inverter unit checks ok
We serviced a
GENERAL ELECTRIC WASHER
Model GTW330ASK0WW
Near Colorado Springs, CO 80909
Roman
Job Details: 08/18/2023
"Washer full of water, got the washer to drain and spin. Ran a speed wash and washer agitates. Washer drained out and spun out, finished the cycle.Only noticed gear case fluid under it. Washer is working fineCustomer was going to do a tub clean and a load after I left."
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JVM3160RF8SS
Near Pueblo, CO 81001
James
Job Details: 08/18/2023
installed ordered parts all ops test good
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GPS0
Near Colorado Springs, CO 80924
Mathew
Job Details: 08/18/2023
"Tightened connection on valve. Test op, unit working as expected. Left test strips."
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF705HPS01
Near Colorado Springs, CO 80925
Carlos
Job Details: 08/18/2023
7737130136 Called tech line. Installed door and filter assembly. Reservoir was frozen as well thawed out. Both ice maker and dispenser release water. Cx will observe if Ice maker dumps ice.
We serviced a
GE REFRIGERATOR
Model GNE27JYMWFFS
Near Silverthorne, CO 80498
Erik
Job Details: 08/18/2023
onnect to smartHQ service:RUN DIAGNOSTIC/ COMPRESSOR TEST:FAIL: 0-1* change in evap temp in 10 min.(no R600 coolant in sealed system) NEED R600 and manifold/tanks/torch (or lockring)compressor WR87X43805NO REPAIRGEH case#10843516
We serviced a
GE WASHER
Model GTW335ASN2WW
Near Colorado Springs, CO 80905
Carlos
Job Details: 08/18/2023
"Ran test op, found power in outlet was out. Needs an electrician to fix wall outlet"
We serviced a
KITCHENAID REFRIGERATOR
Model KSRA25CNSS00
Near Colorado Springs, CO 80920
Mathew
Job Details: 08/18/2023
Needs new icemaker. Cx wants to hold off on repair. Collected svf $129.95 CK Auth# 99A4RUQuote is good for 30 days. Part #2198597 $198.78Tax $16.30Service fee $129.95Labor $189.95 Consumables $14.50Total $549.48$359.53 due today$189.94 due on install.
We serviced a
GE WASHER
Model GTW465ASN8WW
Near Colorado Springs, CO 80906
Roman
Job Details: 08/18/2023
Tried getting the agitator out and it wouldnt come apart. Tilted the washer and used a magnet to get the nail out. Job completed. Total 129.95 scLabor 30.00Total 159.95
We serviced a
GE REFRIGERATOR
Model GSH22JFTABB
Near Fountain, CO 80817
Roman
Job Details: 08/18/2023
"Checked compressor and components of the fridge. Fridge getting power but nothing is turning on indicating a control board issue. Recommend replacing the control board. Control board #WR55X10603 $363.15Tax $29.78Total parts $393.91Labor $129.95$14.95SC $ 129.95Total $ 668.31Tried calling landlord but has to talk to the owner, I did not collect a sc"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Fountain, CO 80817
Roman
Job Details: 08/18/2023
Fridge not making any noises when I arrived. Lowered fridge temps and checked compressor and condenser fan. Compressor is running very hot. Condenser fan and FF section fans working and not making noise. Not sure what was making the noise. Told customer to call if noise continues
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRMF706EBS01
Near Cañon City, CO 81212
Kris
Job Details: 08/18/2023
cx does not want to go through with repairs.fc temp@24.9 rc temp@61.07737127967
We serviced a
WHIRLPOOL DRYER
Model MED5500FC0
Near Colorado Springs, CO 80905
Carlos
Job Details: 08/18/2023
"Installed Control board, ran test op all ok. Cx paid in full in a previous visit."
We serviced a
GE OVEN
Model P2S930SEL2SS
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 08/18/2023
Unit not heating to higher than 400+ temps. Found open convections element. Needs element replaced. Quoting part prices below labor would be $189.95 upon return service if Cust decides. Charging service call. $136.45 CC Auth# 9UPMLH Cust will hold off on repairs. WB44X29061 convection element $97.20WB27X29501 mainboard $315.50
We serviced a
SAMSUNG DRYER
Model DVE45B6300C/A3
Near Colorado Springs, CO 80910
Mathew
Job Details: 08/18/2023
"Unit receiving 120v L1 to neutral, 19v L2 to neutral, 94v L1 to L2. Machine will not power on. Flipped breaker, power is restored. Unit working as expected. Collected svf $129.95 in cash."
We serviced a
WHIRLPOOL RANGE
Model KSGG700ESS3
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 08/18/2023
Oven bake is tripping breaker every time it gets used. Surface burners and broil work but oven is on gfci outlet AND breaker and unit is spark type ignition. Disclosed power requirements and suggested to replace to dedicated standard breaker. FCC
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Monument, CO 80132
Glenn
Job Details: 08/18/2023
"Unit Fills & Drains. No Wash. Bad Sump & Motor Assy. Install New Sump & Motor Assy, All OPS Test:OK, No Leaks, Installed Leak Detector for safety."
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Colorado Springs, CO 80907
Carlos
Job Details: 08/18/2023
Latch needed to be reattached. Ran test op all ok
We serviced a
GE DRYER
Model HTX24EASK0WS
Near Colorado Springs, CO 80916
David
Job Details: 08/18/2023
"Checked dryer Found drum off the top front glides Repositioned drum and glides Test ran dryer, sounds great"
We serviced a
KITCHENAID COOKTOP
Model KCGS556ESS02
Near Monument, CO 80132
Glenn
Job Details: 08/18/2023
"Center burner was continously clicking, customer unplugged unit, then plugged back in and clicking stopped. Seems to be working fine now. Customer was unaware of unit not being covered under warranty. Paid SC Fee of $129.95 , Autho#WTH39V"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Grand Junction, CO 81506
James R
Job Details: 08/18/2023
"Replaced water valve. Checked icemaker it is broken. Replaced. Test cycled thru 44,45,47 and 48 all checked good. customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Grand Junction, CO 81505
James R
Job Details: 08/18/2023
"Replaced chute,seal,separator,hose retainer,coupling and ice container. test operation normal. customer signed waivers.Please fill out whirlpool tech satisfaction survey. Thank You."
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Colorado Springs, CO 80924
Aaron
Job Details: 08/18/2023
"No error codes upon arrival, unit noisy durning drain, removed zipper from pump, tested unit through diagnostics, working and draining well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ1
Near Grand Junction, CO 81501
James R
Job Details: 08/18/2023
Had to hook up pwr to unit. Also the water line was leaking. Had waivers signed. Cleaned water trap. Cleared code. Ran unit thru diagnostics operation normal. No error codes when done. Customer will need to have unit installed properly. We do not do installs. Put leak board under unit. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ06
Near Grand Junction, CO 81504
James R
Job Details: 08/18/2023
Replaced icemaker and valve. Everything was thawing in frz area. put a valve on service port. Unit low on 600 found a leak at the high pressure joint from condenser cut it out and soldered in a joint tube. evac system then recharge. Low side 4 vacumn. Unit is starting to cool. customer signed waivers.Please fill out whirlpool tech satisfaction survey. Thank You.; used 1 BPV31 (valve) from stock
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5001SR/AA
Near Colorado Springs, CO 80915
Brandon
Job Details: 08/18/2023
Replaced parts and tested op all checks ok hass passed
We serviced a
WHIRLPOOL M/W OTR
Model UMV1170LS00
Near Grand Junction, CO 81503
James R
Job Details: 08/18/2023
Replaced cavity thermostat. Reassembled unit and reinstalled on wall. test op's. Good normal.Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SAMSUNG DISHWASHER
Model DW80B6060US/AA
Near Colorado Springs, CO 80920
Jeremy
Job Details: 08/18/2023
Installed new harness and cover. Tested op and ran HASS. Checked for leaks and placed leak detection strip under unit. Asked CX to complete the survey.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF707ESS01
Near Colorado Springs, CO 80920
Glenn
Job Details: 08/18/2023
"Defrost massive ice buildup. Install New Damper Assy, Fan w/ Harness & Sensors, Support, & RS Door Gasket. Adjust Gasket. All OPS Test:OK"
We serviced a
MAYTAG DRYER
Model MED6230HW2
Near Colorado Springs, CO 80908
Aaron
Job Details: 08/18/2023
"Unit has correct polarity and 240v at time of inspection, tested unit on timed dry and heating well. Unit uses 30 amp breaker. Discussed situation with whirlpool techline. No voltage change during use and 22 amp draw. SR7737130374. Recommend electrician for the breaker.W11541971 (attaching file). Advised customer of survey."
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Albuquerque, NM 87120
Joseph
Job Details: 08/18/2023
"Unit making a loud grinding noise when agitating. Inspect and troubleshoot unit. Actuator was no longer activating. Replaced cam and actuator from truck stock. Unit tested good. Unit is good to go.; used 1 W10721967 (CAM), and 1 W11481722 (Actuator) from stock"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HBS02
Near Colorado Springs, CO 80927
Aaron
Job Details: 08/18/2023
"Replaced evaporator fan motor assembly and ice maker assembly, performed fill and harvest test in diagnostics, unit needs time to cool back down. Advised customer of 5 star survey."
We serviced a
SAMSUNG WASHER
Model WF42H5000AW/A2
Near Colorado Springs, CO 80918
Brandon
Job Details: 08/18/2023
"Replaced diaphragm and ran smart install mode, no leaks all checks ok"
We serviced a
GENERAL ELECTRIC WASHER
Model GTW845CPN0DG
Near Breckenridge, CO 80424
Erik
Job Details: 08/18/2023
connect to smartHQ service:no ACTIVE errorsout of balance load (N/A)CX states: only happens on NORMAL cycle with colorsCX education ( try deep fill/ rinse option on active wear)
We serviced a
GENERAL ELECTRIC M/W OTR
Model PVM9179SK6SS
Near Breckenridge, CO 80424
Erik
Job Details: 08/18/2023
INSTALL PARTS/TEST: GOODdamage to unit found after uninstalling: dropped or crushed (*SEE QUICK PICS)UNIT DAMAGE NOT REPAIRABLEcase #10840281
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Albuquerque, NM 87120
Joseph
Job Details: 08/18/2023
Installed part listed. Unit tested good. Unit is good to go.
We serviced a
JENNAIR WALLOVEN
Model JMW2430DS01
Near Albuquerque, NM 87120
Joseph
Job Details: 08/18/2023
Installed part listed. Unit tested good. Unit is good to go.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS06
Near Albuquerque, NM 87114
Joseph
Job Details: 08/18/2023
Unit not cooling after repair. Cooling in the freezer section but not the refrigerator side. Checked pressures. Low side sitting at -5 and high side at 100. Air in the system with low charge. Vacuum and recharged 56g of R600a. Pressures are good with low side at -20 and high side at 30. Let customer know to wait 24 hours for cooling. Unit is good to go.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Rio Rancho, NM 87124
Joseph
Job Details: 08/18/2023
Soap dispenser not closing. Inspect unit. Found debris in between lock and the dispenser cover. Cleared debris. Unit tested good. Unit is good to go.
We serviced a
WHIRLPOOL WALLOVEN
Model GBD307PDT7
Near Albuquerque, NM 87104
Joseph
Job Details: 08/18/2023
Screen does not turn on. Inspect and troubleshoot unit. Unit will need new control panel. The part is no longer available and discontinued.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Albuquerque, NM 87121
Joseph
Job Details: 08/18/2023
Installed parts listed. Unit was still shaking. Took out wash plate and found that the hub was also loose and screws were not screwed in all the way. Secured hub. Put unit back together. Test unit. Unit tested good. Unit is good to go.
We serviced a
GE WASHER
Model GUD27ESSM1EW
Near Colorado Springs, CO 80905
David
Job Details: 08/18/2023
"Checked washer Found belt had gotten knocked off motor and pully by clothes that had escaped from the tub.Belt good, reinstalled."
We serviced a
MAYTAG RANGE
Model MET8800FZ05
Near Colorado Springs, CO 80922
Aaron
Job Details: 08/18/2023
Upper oven cavity is discolored on bottom of cavity from customer using a mat with aluminum rack above. Unit is working and heating well otherwise. Discussed situation with techline. SR7737129368
We serviced a
BOSCH REFRIGERATOR
Model B36FD50SNS/01
Near Cañon City, CO 81212
Kris
Job Details: 08/18/2023
rc temp@43.0 fc temp@0.8 called techline per techlne do not change any parts. all sensors are working to spec at this time. cx should buy digital thermometer.
We serviced a
FRIGIDAIRE ICE MACHINE
Model FRSS26L3AF0
Near Colorado Springs, CO 80909
David
Job Details: 08/18/2023
"Checked Ran icemaker through test cyclesNo errors Icemaker set for small cubes, reset size to large and tested fill, all ice molds filled"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Albuquerque, NM 87106
Jason
Job Details: 08/18/2023
installed damper and im unit opperation checks ok
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Albuquerque, NM 87111
Jason
Job Details: 08/18/2023
installed control unit checks ok
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Albuquerque, NM 87112
Jason
Job Details: 08/18/2023
checked unit found loose ui connection to control seated plug unit opperation checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS311SDHM0A
Near Sandia Park, NM 87047
Jason
Job Details: 08/18/2023
checked unit found a bad connection to inlet valve repaired connection unit checks ok
We serviced a
WHIRLPOOL DRYER
Model WED5100HC0
Near Tijeras, NM 87059
Jason
Job Details: 08/18/2023
checked unit found f2e2 ui not responding console touch pad is bad console neededsc$141.00misc$17.50labor$206.10console#W11419056$332.24tx$28.24total$725.08paid cash $141.00
We serviced a
JENNAIR REFRIGERATOR
Model JFFCC72EFP02
Near Colorado Springs, CO 80906
Ralph
Job Details: 08/18/2023
"installed harness and unit checked okay, cust paid total autho no. VFKL93"
We serviced a
THERMADOR DISHWASHER
Model DWHD440MFP/08
Near Colorado Springs, CO 80906
Ralph
Job Details: 08/18/2023
installedlisted part and unit checked okay
We serviced a
SUBZERO REFRIGERATOR
Model 550 - RH
Near Colorado Springs, CO 80909
Ralph
Job Details: 08/18/2023
installed part and unti chekced okay...cust paod tota billautho no H933UJ
We serviced a
GE DRYER
Model PFD95ESPT1DS
Near Leadville, CO 80461
Erik
Job Details: 08/18/2023
*CX says: 'over heats after I use it 2-3 times in a row'**Leadville is above 10K ftconnect to smartHQ service:F11 (active) blocked vent algorithmcheck vent (exterior) no blockage?call GE TAG: inlet and outlet temps and in spec refer CX to 1800 GE CAES for use and care
We serviced a
SAMSUNG REFRIGERATOR
Model RF22R7351SR/AA
Near Colorado Springs, CO 80927
Brandon
Job Details: 08/18/2023
"Error 39c, replaced ice maker, auger motor bad replaced auger assy, reset ice maker it cycled all checks ok hass passed"
We serviced a
KITCHENAID MICROWAVE
Model KOCE500ESS05
Near Colorado Springs, CO 80919
Glenn
Job Details: 08/18/2023
Install New Motor & Adapter. All OPS Test:OK
We serviced a
FRIGIDAIRE DISHWASHER
Model FFCD2413US5A
Near Colorado Springs, CO 80909
David
Job Details: 08/18/2023
"Checked dishwasher Drain hooked to disposal, was not looped up above the disposal. Rerouted hose to form loop.Suggest capping disposal dishwasher port and attach drain hose to the air gap stand pipe"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHV08
Near Palisade, CO 81526
James R
Job Details: 08/18/2023
Not making ice is not the issue. Ice ben is full.The frz has lots of frost. The door seal is not sealing properly. Need to heat and reform the gasket. Did so sealing good now. Wiped down freezer of ice and moisture. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DRYER
Model WED5000DW2
Near Peyton, CO 80831
Aaron
Job Details: 08/18/2023
"Thermostat and heating element shorted out. Unit is heating well, low 124f and high 235f. Timer is progressing, vent goes to the roof, explained to customer how longer venting can lead to longer dry times. Advised customer of survey."
We serviced a
MAYTAG WASHER
Model MVW6200KW0
Near Peyton, CO 80831
Aaron
Job Details: 08/18/2023
"Actuator is shorted out, unit is unable to agitate or spun, replaced actuator and tested unit through diagnostics. Working well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Peyton, CO 80831
Aaron
Job Details: 08/18/2023
"Removed and replaced ACU assembly, unit powered on and working well now, needs time to cool down. Auth remaining balance 275.95 ck#6138 #P4LEPW"
We serviced a
GE DISHWASHER
Model DDT700SSN5SS
Near Colorado Springs, CO 80919
David
Job Details: 08/18/2023
Replaced front coverCk happy
We serviced a
MAYTAG DRYER
Model MED7230HW2
Near Albuquerque, NM 87111
Larry
Job Details: 08/18/2023
Installed repair kit ans tested good - Unjit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Albuquerque, NM 87109
Larry
Job Details: 08/18/2023
Installed door panel and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Los Lunas, NM 87031
Larry
Job Details: 08/18/2023
Installed
We serviced a
WHIRLPOOL DRYER
Model WED8127LC1
Near Los Lunas, NM 87031
Larry
Job Details: 08/18/2023
CX complaint - Dryer squeeling loudly - Inspected unit and found the idler failed - Replace with TS and tested good - Unit is good to go; used 1 W10837240 (Bracket) from stock
We serviced a
GENERAL ELECTRIC DRYER
Model GFD55ESSN1WW
Near Pueblo West, CO 81007
James
Job Details: 08/18/2023
installed ordered parts all ops test good. per AR no POP needed.
We serviced a
WHIRLPOOL RESIDENTIAL REFR
Model WRF555SDFZ11
Near Pueblo West, CO 81007
James
Job Details: 08/18/2023
installed ordered parts all ops test good
We serviced a
SUBZERO REFRIGERATOR
Model 532
Near Pueblo, CO 81006
James
Job Details: 08/18/2023
found debris in drip tray for fridge evap tray also sealant came off causing water to leak to bottom of fridge. also found large amounts of dust on condenser fan and condenser. cleaned off and cleared out drip tray and applied sealant to tray. collected 269.90 $269.90 CC Auth# T3JKE9 for sc and min labor.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, NM 87109
Larry
Job Details: 08/17/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
JENN-AIR BEVERAGE COOLER
Model JUB24FLERSOO
Near Albuquerque, NM 87122
Larry
Job Details: 08/17/2023
CX complaint - Cooler in the casita not cooling properly - Inspected unit and found the control is cycling the fans and compressor in erratically - Unit will need control board - CX wants to shop around for new unit - Collected $140.18-Auth-343K3RControl-$485.06Labor-$409.95MPS-$17.50Tax-$82.09
We serviced a
WHIRLPOOL DRYER
Model MED4500MW0
Near Albuquerque, NM 87109
Larry
Job Details: 08/17/2023
CX complaint - Dryer too hot - Inspected unit and found pbstruction in venting - Advised cx to have vents cleaned - Also noticed squeeking when drum is turning - Checked and found roller shaft glazed - Removed glaze and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ03
Near Colorado Springs, CO 80906
Carlos
Job Details: 08/17/2023
Installed water valves runs all ok.
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near Colorado Springs, CO 80916
Carlos
Job Details: 08/17/2023
"7736646478 Called Tech line for 41:08 minutes. Took videos of violent shaking, checked floor level according to their methodology. Was told all information is being transferred to engineering. And will contact me via email with corrective actions. If no corrective actions they will contact customer. I aso explained to tech line that the customer informed me that the shaking of the washer ripped the customer water supply line and damaged the floor and the door of closet."
We serviced a
GENERAL ELECTRIC WASHER
Model GTW465ASN9WW
Near Colorado Springs, CO 80916
Mathew
Job Details: 08/17/2023
"Replaced control. Test op, unit is working as expected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT519SZDM05
Near Granby, CO 80446
Antonio
Job Details: 08/17/2023
Found unit lost all r134a called whlp unit is up for review SR7737116085Auth#vhc9f3
We serviced a
CAFE DISHWASHER
Model CDT845P3N5D1
Near Fraser, CO 80442
Erik
Job Details: 08/17/2023
install hardware on site: NO ADJUSTMENT FOR LOWER RACK ROLLERSWORKING AS DESIGNEDJOB COMPLETE
We serviced a
GE WASHER
Model GTW720BSN1WS
Near Fraser, CO 80442
Erik
Job Details: 08/17/2023
install part on site/ test:connect to smartHQ service: NO ERROR CODESJOB COMPLETE
We serviced a
GE REFRIGERATOR
Model GYE18JYLFFFS
Near Winter Park, CO 80482
Erik
Job Details: 08/17/2023
INSTALL ERROR: door scratched due to install of handle (design flaw) pressure clip and 'pull-down' installation requiredGE BULLETIN: TB06-22 RFF door damaged WR78X38525*SEE QUICK PICS
We serviced a
SAMSUNG REFRIGERATOR
Model RF25HMEDBSG/AA
Near Pueblo, CO 81001
Brandon
Job Details: 08/17/2023
"39c error, replaced ice maker and cycled all checks ok hass not compatible"
We serviced a
SAMSUNG WASHER
Model WA52A5500AC/US
Near Pueblo, CO 81003
Brandon
Job Details: 08/17/2023
Replaced lid all checks ok hass passed
We serviced a
SAMSUNG WASHER
Model WA40A3005AW/A4
Near Pueblo West, CO 81007
Brandon
Job Details: 08/17/2023
"Checked all water connections, ran smart install, checked pressure switch, all checks ok, unit is not leaking, drain is backing when washer is draining"
We serviced a
SAMSUNG REFRIGERATOR
Model RF23A9771SR/AA 10
Near Colorado Springs, CO 80925
Jeremy
Job Details: 08/17/2023
Installed all ordered parts. Tested operation of eveything. Checked for leaks. Ran HASS. Asked CX to complete the survey.
We serviced a
MAYTAG WASHER
Model MVWC565FW0
Near Monument, CO 80132
Glenn
Job Details: 08/17/2023
"Problem w/ Spin cycle.Bad Gearcase & Basket. Splines worn off and basket never moves. (Plus Misc parts, Tax & Labor)Just Gearcase - W11454734 $347.58 , & Basket - W10752719 $372.94 are more than customer prefers to spend. Declined Estimate. Paid SC fee of $89.95, Autho#K394M4"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Colorado Springs, CO 80924
Mathew
Job Details: 08/17/2023
"Replaced door, test op all okay."
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW2
Near Colorado Springs, CO 80920
Mathew
Job Details: 08/17/2023
"Leveled washer, tighten cam assembly nut. Test op with load of towels, all okay."
We serviced a
WHIRLPOOL REFRIGERATOR
Model ET18GMXHW0
Near Colorado Springs, CO 80903
Carlos
Job Details: 08/17/2023
Ran test op found that drain was clogged with ice. Unclogged and cleaned freezer section. All ok Cx will observe
We serviced a
THERMADOR STOVE
Model PRD366WHU/01
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 08/17/2023
"Installed replacement WiFi board. Unit check ok. Charged labor as quoted $189.95 CC Auth# XP3H3N. Upon arriving found display dead which was original issue. Replaced WiFi board and Cust will keep track of unit functionality, charged labor as quoted $189.95 CC Auth# XP3H3N"
We serviced a
HOTPOINT STOVE
Model n/a
Near Colorado Springs, CO 80903
Jerimiah
Job Details: 08/17/2023
"Gas smell when running oven. Found bake shutter open, adjusted for high altitude and shut shutter. Now ignites within 1-2 seconds where prior was 5-6. Unit check ok. No model serial available checked all over and inside unit. Charged service call $129.95 CC Auth# 9P9HU4"
We serviced a
GE DISHWASHER
Model GDT550TYR3SS
Near Colorado Springs, CO 80903
Roman
Job Details: 08/17/2023
Plug that connects to the drain pump broke. Needs to be reworked and reconnected. Required the plug to the wires and tested the dw. Dw working great.
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5201SR/AA
Near Colorado Springs, CO 80909
Jeremy
Job Details: 08/17/2023
Installed new compressor and associated parts. Tested operation. Ran HASS. Unit working to the best of my knowledge. Asked CX to complete the survey.
We serviced a
SAMSUNG REFRIGERATOR
Model RF23A9671SR/AA
Near Colorado Springs, CO 80918
Jeremy
Job Details: 08/17/2023
Installed part. Tested operation. Checked for leaks. Cheked under top panel for HASS connection but didnt have one. Kitchen under remodel and unable to roll refridgerator foward to access back of unit for HASS connection. Asked CX to complete the survey.
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAESG/AA 04
Near Monument, CO 80132
Jeremy
Job Details: 08/17/2023
Installed all parts. Reset icemaker. Not HASS compatiable. No leaks. Asked CX to complete the survey.
We serviced a
SAMSUNG RANGE
Model NX60A6711SS/AA
Near Fountain, CO 80817
Roman
Job Details: 08/17/2023
Installed new control board and touchpad. Tested the range and its working great. ; used 1 DG94-04041 (Touchpad) from stock
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Peyton, CO 80831
Aaron
Job Details: 08/17/2023
"Wires broken in door panel, control board is shorted out, replaced control and repaired unit. Tested and working well now. Property vacant, unable to obtain signature or advise of survey."
We serviced a
JENN-AIR COOKTOP
Model JGD3430BW00
Near Colorado Springs, CO 80919
Glenn
Job Details: 08/17/2023
"Trouble w/ LF Burner not igniting.Appears to be working at this time?HARNS-WIRE (Switch Assys) - W10854963 $261.12 , Valve - LF Control - W10467730 $82.12 , Burner Assy (w/ ignitor) RF - 74007736 $120.78 , Tax $38.05 , MPS $14.50 , Labor $184.95 , Declined Estimate for now, Paid SC fee of $149.95 , Autho #LPE33T"
We serviced a
WHIRLPOOL WASHER TOP LOAD
Model CAE2745FQ1
Near Fountain, CO 80817
Roman
Job Details: 08/17/2023
"Ran washer and it would not fill. Turned the water on at the wall. Washer agitates and drains out, middle of the cycle washer stopped. Ran diagnostic test and washer did not have error codes. Ran test and washer went through the test just fine. Calibrated the washer.Was going to call in to pay sc"