We serviced a
ELECTROLUX WALL OVEN
Model EW30EW55PSD
Near Colorado Springs, CO 80918
Jerimiah
Job Details:
11/13/2024
"Door hinges were left in close position without clips. Was able to reseat hinges with clips and reinstall door, unit check ok charged service call $139.95 CC Auth# 9PL33U"
We serviced a
HISENSE FREEZER
Model FC72D6BWE
Near Colorado Springs, CO 80909
Charles
Job Details:
11/13/2024
"No cool, open winding on compressor. Will buy new. Service fee $139.95 paid autho R44H3H"
We serviced a
MIELE DISHWASHER
Model G2020SC
Near Colorado Springs, CO 80921
Charles
Job Details:
11/13/2024
"Unit not draining completely, clean ball check valve in sump and rerouted drain hose under sink to have high loop into disposal Service fee 159.95 paid URV3NH"
We serviced a
WHIRLPOOL WASHER
Model WFW8500SR01
Near Edgewood, NM 87015
Jason
Job Details:
11/13/2024
Checked unit found hose had come off. re-secured hose unit checks ok
We serviced a
MAYTAG WASHER
Model MVWB766FW1
Near Jacksonville, OR 97530
Jeff
Job Details:
11/13/2024
Units rotor froze to stator and caught fire. Contacted tech line and sent pics they did a report and gave me a sr# 7740316281 customer will reach out to her third party
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM11
Near Albuquerque, NM 87122
Jason
Job Details:
11/13/2024
Checked unit could verify cx cxomplaint at this time. cx said sound is intermitant. they will try and record sound next time unit makes it
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Los Lunas, NM 87031
Larry
Job Details:
11/13/2024
"CX complaint - Not washing - Inspected unit and found the wash motor failed - Replaced with pre-id part, ran test cycle and tested good - Unit is operating as designed"
We serviced a
MAYTAG DRYER
Model MED6200KW1
Near Albuquerque, NM 87106
Jason
Job Details:
11/13/2024
Installed parts unit opperation checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Rio Rancho, NM 87124
Joe
Job Details:
11/13/2024
"Cx complaint, not washing dishes. Inspected unit, found wash pump not working. Replaced sump assembly. Tested unit in diagnostics and quick wash. Wash motor working fine. Unit good to go. Cx didn't have copy of receipt Advised cx about survey"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Estancia, NM 87016
Jason
Job Details:
11/13/2024
Installed part ran a quick cycle to test opperation. unit opperation checks ok
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Rio Rancho, NM 87124
Joe
Job Details:
11/13/2024
"Cx complaint, lid coming apart. Inspected washer and found glue coming loose that holds glass to frame of lid. Unit working as designed the way it is. Talked to trade care and was told this is cosmetic and not covered. Advised to have cx call customer service if they had any questions Sr 7740301179"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KBS1
Near Cañon City, CO 81212
James
Job Details:
11/13/2024
Installed ordered parts tested ops all ckok left litmus
We serviced a
WHIRLPOOL DRYER
Model WED6605MW0
Near Aspen, CO 81611
James R
Job Details:
11/13/2024
Signed disclaimer.Replaced heater and thermal cutoff. Is heating. Checked vent restriction is 25 good. Checked temp vent hooked up with load 148 degrees good. Temp cycling on and off as should. Put some towels in unit. Auto dry sensing is working. switched to wet would time down then back up so is sensing the dampness of the cloths. Is important that cloths must touch the sensor in the front. So dry properly also too large of loads will restrict air circulation and affect drying. Timed dry cloths do not need to touch sensor. Rely on temp setting. Unit is operating as should. Please fill out tech satisfaction suevey. Thank You.
We serviced a
WHIRLPOOL RANGE
Model WFE505W0HW5
Near Leadville, CO 80461
Antonio
Job Details:
11/13/2024
Installed new acu turned oven on to 350 degrees and unit tested good
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near El Jebel, CO 81623
James R
Job Details:
11/13/2024
N/A disclaimer No water coming in. Checked float was stuck up put to correct position. Test in service diagnostics test operating as should. No error codes reappeared. Put a leak board under unit and took pic. May remove later if no leaks appear. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP730HAMZ0
Near Gypsum, CO 81637
Antonio
Job Details:
11/13/2024
Installed new sump assembly ran a cycle for proper operation and for leaks unit tested good Also advised cx of water strips
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ11
Near Eagle, CO 81631
Antonio
Job Details:
11/13/2024
Started to in cut tubing when noticed capillary tub broken going in to fridge called whlp 7740317797 unit is up for review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Fountain, CO 80817
Carlos
Job Details:
11/13/2024
Installed ice maker and valve all ok.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Colorado Springs, CO 80923
Aaron
Job Details:
11/13/2024
"Removed and replaced front panel and control, ran unit through diagnostics, working well now, no leaks, installed litmus strip, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Colorado Springs, CO 80922
Aaron
Job Details:
11/13/2024
"Customer complains of unit shaking violently during spin, inspected unit, found damper not properly engaged to tub, corrected and tested unit through quick cycle, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Colorado Springs, CO 80922
Aaron
Job Details:
11/13/2024
"Customer complains of unit shaking violently during spin, inspected unit, found damper not properly engaged to tub, corrected and tested unit through quick cycle, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS10
Near Peyton, CO 80831
Jerimiah
Job Details:
11/13/2024
Installed replacement components unit check ok.
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Cañon City, CO 81212
James
Job Details:
11/13/2024
Installed preordered parts
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHW06
Near Colorado Springs, CO 80911
David
Job Details:
11/13/2024
Replaced icemaker and thermistor. Explained that this type of icemaker checks to see if there is ice in the bin and that could be every half hour if the bin is full. New icemaker seems to be quieter.
We serviced a
WHIRLPOOL WALL OVEN
Model WOES5030LZ01
Near Colorado Springs, CO 80908
Aaron
Job Details:
11/13/2024
"Removed and replaced UI console, programmed unit, tested operation, working and heating well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Colorado Springs, CO 80904
Carlos
Job Details:
11/13/2024
Installed tub ran test allok
We serviced a
WHIRLPOOL RANGE
Model WFE775H0HZ4
Near Eagle Point, OR 97524
Jeff
Job Details:
11/13/2024
Installed parts customer approved looks
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Monument, CO 80132
Dvante
Job Details:
11/13/2024
"Check unit. Saw the unit wasnt cleaning properly. Checked under, saw the pin come on the actuator. Did the diagnostic test. All tested ok and working as designed"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Bend, OR 97702
Levi
Job Details:
11/13/2024
"Found icemaker seaming to be broken in the middle of the harvest mode. Replaced icemaker and valves, tested good"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW08
Near Medford, OR 97504
Jeff
Job Details:
11/13/2024
Installed door tested machine working as should
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ5
Near Bend, OR 97701
Levi
Job Details:
11/13/2024
"Replaced listed parts, tested good. It would lite but the igniter would keep clicking. Now it's good"
We serviced a
SAMSUNG WASHER
Model WF45B6300AC
Near La Pine, OR 97739
Levi
Job Details:
11/12/2024
"Replaced door seal, tested, all checks okay and no leaks detected"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ0
Near Bend, OR 97703
Levi
Job Details:
11/12/2024
"Replaced spray arms, tested, all checks okay. No leaks detected"
We serviced a
GE RANGE
Model JSS86SP5SS
Near Basalt, CO 81621
Sean
Job Details:
11/12/2024
customer signed disclaerchecked unit MN/SN goodchecked unit = power tested good at wallchecked burrners = warming burner did not heat up. removed burners and control panel checked wires found wire to the warning zone was not connected to the burner. reattached wire.back left burner tested good cycles on and off.front left burner tested good on small and large burner. cycles on and off.front right burner tested good small and large burner cycled on and off.back right burner tested good cycled on and off warming zone burner tested unit warmer heats uptested good all burners are working as designed.please fill out a tech servey.
We serviced a
WHIRLPOOL DRYER
Model WED8540FW0
Near Colorado Springs, CO 80906
Carlos
Job Details:
11/12/2024
Installed repair kit cx paid in full all ok $437.82 CC Auth# VLP399
We serviced a
BOSCH DISHWASHER
Model SHPM88Z75N/20
Near Colorado Springs, CO 80920
Charles
Job Details:
11/12/2024
"E03&E07 errors, replace power module and vent fan"
We serviced a
BOSCH DISHWASHER
Model SHXM88Z75N/18
Near Colorado Springs, CO 80907
Ralph
Job Details:
11/12/2024
INSTALLED PARTS UNIT TESTED OKAY
We serviced a
WHIRLPOOL MICROWAVE
Model RMC305PVS01
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
11/12/2024
"Unit door still clicking, found plastic frame sagging causing door to click loudly, no help can be done to unit, unit not heating due to improper state of door switch, repaired. Unit check ok."
We serviced a
FRIGIDAIRE ICE MACHINE
Model GEMU090
Near Peyton, CO 80831
Charles
Job Details:
11/12/2024
"Clean light on, show customer cleaning instructions printed on inside of door that requires descaling solution service fee $139.95 paid check #241 autho T443AF"
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5501SR/AA
Near Peyton, CO 80831
Brandon
Job Details:
11/12/2024
"Family hub not working, getting 12vdc to f-hub, wire harnesses all ok checked for continuity, need to replace f-hub, Svf paid $129.95 Auth# XXFX34, DA82-02711L $543.96, Labor $189.95, Svf 129.95, Mps $14.50, Tax $44.60"
We serviced a
SAMSUNG REFRIGERATOR
Model RF261BEAESR/AA
Near Colorado Springs, CO 80922
Brandon
Job Details:
11/12/2024
"Replaced ice pipe assy and cycled ice maker all checks ok, Labor and mps paid $204.45 Auth# A949K3"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF330PAHS3
Near Colorado Springs, CO 80927
Brandon
Job Details:
11/12/2024
"Found filter clogged and no rinse aid in dispenser, cleaned filter and recommend using rinse aid, no error codes"
We serviced a
SAMSUNG DRYER
Model n/a
Near Colorado Springs, CO 80927
Brandon
Job Details:
11/12/2024
"Not getting 240v, checked breaker not tripped, found burn marks on dryer cord outlet, recommend electrician to fix outlet"
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5561SR/AA
Near Fountain, CO 80817
Mathew
Job Details:
11/12/2024
Found door damaged. Cx requests quote on panel/door replacementQuote good 30 days. $139.95 CC Auth# J3A49HSvf 139.95MPs 14.50Part DA91-05228A (DA82-02804A)? $ 512.42Tax 42.02Plus size shipping $65.00Labor 199.95$973.84
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5001SR/AA
Near Peyton, CO 80831
Brandon
Job Details:
11/12/2024
"Replaced parts, vacuumed, charged unit to spec 72g, hass oqc passed"
We serviced a
GE WASHER
Model GTW335ASN2WW
Near Glenwood Springs, CO 81601
Sean
Job Details:
11/12/2024
customer signed disclamerchecked MN/SN/POP goodchecked water line and drain =goodlooked at water pump =goodfound the tub has a crack on botom right side needs new tub assembly. the tub is listed as not a service part online.called tech suport to get part number.tech suport is checking for parts.tech suport said part is not a service part .unit is none servicable.they are looking at replacing the unit..case number ( 14806900 )
We serviced a
GE DRYER
Model GFD85ESSN0WW
Near Blue River, CO 80424
Erik
Job Details:
11/12/2024
wheel dstroyed * see quick picsreplace wheel asm WE03X10016JOB COMPLETE; used 1 WE03X10016 (wheel asm) from stock
We serviced a
GE WASHER
Model GTW485ASW0WB
Near Glenwood Springs, CO 81601
Sean
Job Details:
11/12/2024
customer signed disclamerchecked unit MN/SN checkedchecked unit found that the drain pump was not fully seated. plugged pump in tested unit drained good.please fill out a tech servey
We serviced a
MONOGRAM DISHWASHER
Model ZDT925SINCII
Near Dillon, CO 80435
Erik
Job Details:
11/12/2024
call GE TAG:case# 14799098 rear left corner spot weld broke freeJOB COMPLETECX relations will reach out in 48 hours
We serviced a
SAMSUNG WASHER
Model WA50R5400AV/US
Near Colorado Springs, CO 80911
Mathew
Job Details:
11/12/2024
"Found barrel wobbling under load, displays ub code. Readjusted clothing, got unit to spin out. Recommend damper replacements if issue persists. $139.95 CC Auth# 943A4WSvf 139.95MPs 14.50DC97-16350U 127.32 ea(x4) $509.28Tax $41.76Labor 199.95Repair total $905.44"
We serviced a
THERMADOR DOUBLE WALL OVEN
Model SEC302BP/02
Near Colorado Springs, CO 80921
Charles
Job Details:
11/12/2024
"Upper oven bottom panel damaged by foil, oven liner not replaceable, screw missing from bottom of door panel. Upper oven broiler not working Service fee 159.95 paid autho KKHX3M"
We serviced a
FULGOR MILANO RANGE
Model F6pdf366s1
Near Palmer Lake, CO 80133
Jerimiah
Job Details:
11/12/2024
Unit intermittently double beeping with no reference of error codes. Cust mentioned unit has done some single beeps but nothing coinciding with unit starting issue. Mode distribution doesnt have much information so conjecture is that the power board (hawk3) needs replacing. Cust is holding off because fix is not 100 guaranteed. Received list of emails per Fulgor via Mode that has way too much information to be deciphered. Was not helpful. Closing call.
We serviced a
JENN-AIR REFRIGERATOR
Model JB36NXFXLE01
Near Aspen, CO 81611
James R
Job Details:
11/12/2024
Signed disclaimer. Replaced all lights. Operating as should. Pleasse fill out tech satisfaction survey. Thank You.
We serviced a
JENN-AIR WALL OVEN
Model JJW3430IM00
Near Bend, OR 97702
Levi
Job Details:
11/12/2024
"Replaced console,tested good"
We serviced a
JENN-AIR REFRIGERATOR
Model JF36NXFXDE01
Near Bend, OR 97703
Levi
Job Details:
11/12/2024
"Replaced all lights, tested good"
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSJ0WW
Near Woodland Park, CO 80863
David
Job Details:
11/12/2024
"Replaced water valve, tested, and is operating correctly."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5501SG/AA
Near Colorado Springs, CO 80921
Dvante
Job Details:
11/12/2024
Replaced the ice maker. Ice maker reset. The water went into the ice maker. No error codes. No leaks under unit. Unit working as designed
We serviced a
GE DRYER
Model GFD65GSPN0SN
Near Basalt, CO 81621
Sean
Job Details:
11/12/2024
"customer signed disclamerchecked unit MN/SN goodstarted a field service mode and ran error codes unit had error 1, 2, 9, 10.=1 = outlet thermister. 2= inlet thermister 9= dry load detection trip 10= empty drum detection trip.unit needs and outlet thermisters and thermostats( GFD65GSPN0SN) outlet thermister( 9WE04X30582 ) saftey thermostat( WE04X10190 ) outlet thermostat( WE04X10189 ) radient sensor( WE04X29727 ) hi limit( WE04X10189 ) radient sensor.parts will come up to $139.77 + shippinghowever I found the gas valve was turned off that can acount for all the errors. turned on gas tested unit unit heats to 170 F and and cycles.if problem happens again we will get parts.please fill out a tech serveycustomer paid check # 4795auth code 3PHLUN"
We serviced a
MIELE COFFEE MACHINE
Model CVA7840
Near Breckenridge, CO 80424
Erik
Job Details:
11/12/2024
call miele techn line must manually clean after auto clean cycles for several weeks - check error codes m43small clean tablet required - CX is awareJOB COMPLETE
We serviced a
KITCHENAID REFRIGERATOR
Model kssp48qht00
Near Colorado Springs, CO 80906
Ralph
Job Details:
11/12/2024
installed lisyted parts and charged the unit unit checked okay
We serviced a
MAYTAG WASHER
Model MVWC555BW0
Near Albuquerque, NM 87105
Larry
Job Details:
11/12/2024
CX complaint - Washer not spinning - Inspected unit and found the gearcase failed - Unit will need gearcase - CX does not want to bear the cost of repair - Estimate in QP - Collected SC auth-3UHT9K
We serviced a
MONOGRAM REFRIGERATOR
Model ZISS420DXASS
Near Colorado Springs, CO 80921
Charles
Job Details:
11/12/2024
"Freezer 41, fridge 45, no frost on evaporator, all fans working, condenser completely covered. Needs compressor part WR87X10111Service fee $159.95Labor $795.95Refrigerant $255.85MPS $14.50Part $1130.71Tax $92.72Total $2449.78Declined repair at this time, $159.95 service fee pre-paid autho 4X4XUU"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS04
Near Colorado Springs, CO 80919
Ralph
Job Details:
11/12/2024
"JUST NEEDED TO RESET THE CONTROL BOARDS, CUST TO MONITOR...AUTHO NO. HTCMLK"
We serviced a
WHIRLPOOL WASHER
Model WFW6620HW0
Near Rifle, CO 81650
James R
Job Details:
11/12/2024
Printed labels took pics ready to send.
We serviced a
PROFILE WASHER
Model WPRE6150K2WW
Near Monument, CO 80132
Charles
Job Details:
11/12/2024
"Leaks water from tub seal, bearing gone, needs shift mode assembly part WH38X10017Service fee $159.95Labor $249.45MPS $14.50Part $323.89Tax $26.56Total 774.85Declined repair, will buy new, paid 159.95 autho 494EA3"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSG/AA
Near Colorado Springs, CO 80925
Mathew
Job Details:
11/12/2024
"Found ice blocking auger motor. Defrost, dry and seal room. Adjust fill line, install control. Install clips, icemaker and drain tube. Replace cracked bin. Test op with force run, all okay."
We serviced a
SUBZERO REFRIGERATOR
Model BI-42UFDID/S/PH
Near Colorado Springs, CO 80908
Charles
Job Details:
11/12/2024
Replaced main control board and programmed
We serviced a
WOLF RANGE
Model DF48450CG/S/P
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
11/12/2024
"Back left simmer wouldnt ignite, found orifice plugged, repaired, unit check ok."
We serviced a
WHIRLPOOL WASHER
Model CET9000GQ2
Near Colorado Springs, CO 80903
Carlos
Job Details:
11/12/2024
"Installed control board old control board has burns in motor coms pics uploaded . Unit has insufficient power coming from outlet, need to reset breaker or contact electrician."
We serviced a
AMANA RANGE
Model AEP222VAW2
Near Albuquerque, NM 87114
Joe
Job Details:
11/12/2024
"Cx complaint, oven not working. Installed terminal block , screws and nuts. Tested burners and oven. All working good. Unit good to go"
We serviced a
MAYTAG DRYER
Model MEDX655DW1
Near Albuquerque, NM 87107
Larry
Job Details:
11/12/2024
"Installed timer, ran cycle and tested good - Unit is good to go - Advised CX to have the vents cleaned proffesionally"
We serviced a
ASKO WASHER/DRYER COM
Model T754CW
Near Colorado Springs, CO 80922
Charles
Job Details:
11/12/2024
"No light/ no display, voltage into control. Need part 416515Service fee $159.95Labor $219.95MPS $14.50Part $725.00Tax $59.45Total $1178.85Declined estimate at this time. Paid 159.95 check#7471 autho LNUW34"
We serviced a
MAYTAG DISHWASHER
Model WDT730HAMZ1
Near Albuquerque, NM 87120
Larry
Job Details:
11/12/2024
"CX complaint - Not draining - inspected unit and found harness loose to the drain pump - Secured harness, ran test cycle and tested good - Unit is operating as designed"
We serviced a
AMANA REFRIGERATOR
Model ART308FFDB11
Near Santa Fe, NM 87508
Jason
Job Details:
11/12/2024
Installed fan motor and sealed all gaps unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ02
Near Rio Rancho, NM 87124
Joe
Job Details:
11/12/2024
"Cx complaint, Dishwasher not heating. Installed control and heater ordered last visit. Tested unit in diagnostic mode. Unit getting hot. Unit good to goAdvised cx about survey"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Santa Fe, NM 87507
Jason
Job Details:
11/12/2024
Installed control ran quick cycle unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Rio Rancho, NM 87124
Joe
Job Details:
11/12/2024
"Cx complaint, fresh food section getting too cold. Replaced control ordered last visit. Tested to make sure lights, compressor, fans and dispenser were working. Unit good to go"
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Colorado Springs, CO 80908
Aaron
Job Details:
11/12/2024
"F7E9 locked rotor F0E5 unbalanced load error codes upon arrival, inspected rotor, hand towel binding rotor, corrected and tested, working well now, unit is level, minimal inner and outer tub movement, discussed situation with techline, suspension is not recommended. Advised customer of situation and survey. SR7740310756"
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS1
Near Colorado Springs, CO 80903
Carlos
Job Details:
11/12/2024
"Installed sump assembly, drain pump and valve all ok, left leak strip"
We serviced a
KITCHENAID WALL OVEN
Model KOSE500EBS03
Near Colorado Springs, CO 80906
Carlos
Job Details:
11/12/2024
"Installed control board, sensor and element ran test heats ok maintains temp."
We serviced a
MAYTAG REFRIGERATOR
Model MFI2570FEZ13
Near Pueblo West, CO 81007
James
Job Details:
11/12/2024
Installed ordered/pre-ordered parts tested ops all ckok
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Colorado Springs, CO 80922
Aaron
Job Details:
11/12/2024
"F0E9 off balance error code upon arrival, actuator arm is not properly engaging, corrected and tested unit through diagnostic cycle, working well now. Customer also concerned about drain and spin cycle adding water to cycle, discussed situation with techline, verified normal operation . Advised customer of situation and survey. SR7740307179"
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Colorado Springs, CO 80903
Carlos
Job Details:
11/12/2024
Installed control board all ok.
We serviced a
KITCHENAID COMPACTOR
Model KTTS505ESS2
Near Divide, CO 80814
David
Job Details:
11/12/2024
"Replaced bin, rollers, and pedal. Working much better."
We serviced a
WHIRLPOOL FREEZER
Model WZF34X20DW05
Near Lake George, CO 80827
David
Job Details:
11/12/2024
"Replaced compressor, evacuated and charged system. Unit is cooling down."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM08
Near Colorado Springs, CO 80920
Dvante
Job Details:
11/12/2024
"Replaced the diffuser, thermistor, fan motor, blade and control box. Tested unit. No loud and intermittent noises coming from the unit. Unit working as designed"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS2
Near Colorado Springs, CO 80908
Aaron
Job Details:
11/12/2024
"Right door suspension spring disengaged and came apart, removed and replaced hinges, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Colorado Springs, CO 80907
Carlos
Job Details:
11/12/2024
"Installed spray arm, original was not placed properly after unit was installed (per cx), all ok"
We serviced a
JENN-AIR MICROWAVE
Model JMW2430IL03
Near Colorado Springs, CO 80927
Aaron
Job Details:
11/12/2024
"Inspected unit, found loose connection on common wire in junction box, other lines are secure, common wire requires electrician to correct, discussed situation with techline SR7740305090 and safety team. Advised customer of situation and survey."
We serviced a
KITCHENAID RANGE HOOD
Model KVWB600DSS4
Near Colorado Springs, CO 80916
Jerimiah
Job Details:
11/12/2024
"Installed replacement components, found control power board burned out, shorted against cavity due to sub par mounting pushpins. unit check ok. UI was not needed for this repair."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Bend, OR 97702
Levi
Job Details:
11/12/2024
"Replaced listed parts, tested, all checks okay. Ensures all wires and harness is tight as possible so if unit goes off balance again, it should not effect wires"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Grants Pass, OR 97527
Jeff
Job Details:
11/12/2024
Installed top display tested machine working as should
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Selma, OR 97538
Jeff
Job Details:
11/12/2024
Installed parts tested machine working as should
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Redmond, OR 97756
Austin
Job Details:
11/12/2024
Installed parts ordered. Tested unit all ops sat per factory spec.
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW2
Near Grants Pass, OR 97527
Jeff
Job Details:
11/12/2024
Replaced valve tested machine working as should
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Pueblo, CO 81005
James
Job Details:
11/11/2024
"Found suspension counting out of bracket. Suspension checks ok, secured suspension and balanced unit. ran through all diagnostic test all ckok no errors found."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Peyton, CO 80831
Aaron
Job Details:
11/11/2024
"F6E3 ACU Error code upon arrival, inspected unit and found rotor bolt came off, replaced and secured, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MED5630HW2
Near Albuquerque, NM 87123
Jason
Job Details:
11/11/2024
Installed parts ran timed dry unit checks ok
We serviced a
THERMADOR MICRO DRAWER
Model MD24WS/04
Near Avon, CO 81620
Erik
Job Details:
11/11/2024
*NEW CONSTRUCTION*right contact switch NOT closing * see quick picsreinstall after adjusting the switch asmJOB COMPLETECX not available for signature
We serviced a
THERMADOR BI REFRIGERATOR
Model T36IB100SP/01
Near Vail, CO 81657
Erik
Job Details:
11/11/2024
replacing front panel * see quick picsCall BSH TAG: no service mode yet from factory - CX must reset leaving unit 'on' but then hard reset at breaker box 1 minturn off theater and dynamic light modes/ unit GOOD unit BSH develops service mode CX must utilize Wifi connection to app