We serviced a
LG DRYER ELECTRIC
Model DLE3470M
Near Colorado Springs, Colorado 80920
Jerimiah
Job Details:
01/24/2025
"Unit getting NP error code halfway thru. Per techline control board needs replacing. NP error code is due to something wrong with neutral line of power. Cust holding off. Labor would be $199.95 upon return service if chosen, Cust will look for new appliance. Charging service call $146.95 CC Auth# J9LX44, total with sc part labor tax MPs is $656. EBR85130511 main board $278.60"
We serviced a
WHIRLPOOL WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80915
Mathew
Job Details:
01/24/2025
"Repaired wire into drain pump. Ran a factory cycle, reset machine. Test op all okay."
We serviced a
GE MICROWAVE
Model JVM3160DF8WW
Near Colorado Springs, Colorado 80917
David
Job Details:
01/24/2025
"Checked microwave, control board going out,Cx is opting to buy a new mw."
We serviced a
WOLF RANGE
Model DF48650G/S/P/LP
Near Sisters, Oregon 97759
Austin
Job Details:
01/24/2025
Installed recall kit. Tested unit all ops sat per factory spec.
We serviced a
SUB ZERO REFRIGERATOR
Model CL4850UFDID/S/P
Near Sunriver, Oregon 97707
Levi
Job Details:
01/24/2025
Replaced right hand door switch tested good
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5501SR/AA
Near Colorado Springs, Colorado 80918
Brandon
Job Details:
01/24/2025
"Error 39c, replaced ice maker cycled all checks ok"
We serviced a
SAMSUNG WASHER
Model WA51A5505AV/US
Near Peyton, Colorado 80831
Mathew
Job Details:
01/24/2025
Found 9c8 error on machine. Bad control. Replace control test op on OQC all okay.
We serviced a
SAMSUNG DRYER
Model DVE55CG7100VA3
Near Colorado Springs, Colorado 80920
Mathew
Job Details:
01/24/2025
"Found no continuity at high limit thermostat. Replaced element assy, test op on OQC and quick dry. All okay."
We serviced a
SAMSUNG DISHWASHER
Model DW80B7070UG/AA
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
01/24/2025
"Call tech support for inspection, they told me to raise the front feet high as they would go, ticket being closed and sent to engineering Samsung will contact customer for next steps"
We serviced a
SAMSUNG DRYER
Model DVE52A5500W/A3
Near Monument, Colorado 80132
Mathew
Job Details:
01/24/2025
"Found bad pcb. Ran OQC after install, test op all okay. Educate Cx on using refresh cycle vs steam sanitize. Dryer is working as expected."
We serviced a
SAMSUNG MICROWAVE
Model ME21DG6300SRAA
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
01/24/2025
"Checked unit, found the door wasnt opening properly from the hinge. Went ahead and replaced the door. Also the unit was hanging on the left side. Tighten the screw. Unit is operating as designed."
We serviced a
SAMSUNG REFRIGERATOR
Model RS28A500ASR/AA
Near Colorado Springs, Colorado 80951
Mathew
Job Details:
01/24/2025
"Found magnet out of place on door, not making contact with reed switch. Adjust reed switch, power cycle. Test op all okay."
We serviced a
SAMSUNG RANGE
Model NX58H9500WS/AA
Near Colorado Springs, Colorado 80919
Jerimiah
Job Details:
01/24/2025
Installed replacement igniter. Unit check ok. Charged labor as quoted chk#6804 $199.95 CK Auth# 3XCL44
We serviced a
GE GAS RANGE
Model JGB735SP1SS
Near Colorado Springs, Colorado 80908
Jerimiah
Job Details:
01/24/2025
"Bake igniter bad, needs replacing, Cust holding off, will call if chosen to continue with repairs. Labor would be $219.95 if chosen to do so. Charging service call. $139.95 CC Auth# TJU4RCWB13X25500 bake igniter $135.52"
We serviced a
MAYTAG WASHER
Model MVWB855DC0
Near Albuquerque, New Mexico 87108
Jason
Job Details:
01/24/2025
Checked unit found washplate had come looseand stripped both it and gearcase shaftSC$139.95MPS$17.50LABOR$249.95GEARCASE#W11393685$306.10SLIDER#W10734521$82.02WASHPLATE#W10902814$142.56SPANNER#W10909670$60.68TX$84.89TOTAL$1083.65 Auth code: 9W39NW$151.85
We serviced a
THERMADOR RANGE
Model prd486wigu
Near Colorado Springs, Colorado 80908
Jerimiah
Job Details:
01/24/2025
"Installed LP rework kit, unit check ok. Charged labor $199.95 CC Auth# 4TWNY4"
We serviced a
WHIRLPOOL OVEN
Model WOS51EC0AS04
Near Colorado Springs, Colorado 80922
Jerimiah
Job Details:
01/24/2025
"Unit dead, found TCO open, replaced, unit check ok charged service call, part tax MPs Labor 189.95 chk#2210 $412.94 CK Auth# THU994WPW10545255 TCO $63.35; used 1 WPW10545255 (Thermal fuse) from stock"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Sunriver, Oregon 97707
Levi
Job Details:
01/24/2025
Error code f8e4 indicated water in the overflow tray. Confirm there was water in it so I cleaned it out. Looks like the water is due to excess drippage from the drying vent. Went into programming mode and changed the dry cycle to reduce drippage as per Maytag service bulletin. All other checks okay
We serviced a
SAMSUNG DRYER
Model DV457GVGR/AA
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
01/24/2025
"Replaced all four rollers and idler pulley. Test op on cycle, all okay. Collect labor 189.95 $189.95 CC Auth# HU4P9U"
We serviced a
WHIRLPOOL DRYER
Model WED5620HW1
Near Grand Junction, Colorado 81504
James R
Job Details:
01/24/2025
"Signed disclaimer. Tore apart found heat element bad and in need of a repair kit. Replaced both. Cleaned unit Reassembled run unit test operation is operating as should. Customer paid $574.70 auth code. C939CJPlease fill out tech satisfaction survey. Thank You.; used 1 WP3387747 (Element (Front Blower)), and 1 4392067 (Dryer Kit (4 Roller)) from stock"
We serviced a
SAMSUNG RANGE
Model NX58R9421SS/AA
Near Pueblo, Colorado 81007
James
Job Details:
01/24/2025
Installed ordered parts tested ops all ckok collected 219.95 $219.95 CC Auth# WRLJE4
We serviced a
ELECTROLUX DISHWASHER
Model FFCD2418US3A
Near Colorado Springs, Colorado 80909
David
Job Details:
01/24/2025
"Checked dishwasher, found bottom door sweep seal was out of place, reinstalled sweep, tested and is operating as designed."
We serviced a
DACOR REFRIGERATOR
Model DRF36C000SR/DA
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
01/24/2025
Replaced freezer door. No damage to the new door. Door is opening and closing properly. Unit is operating as designed.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Colorado Springs, Colorado 80925
David
Job Details:
01/24/2025
Installed agitator and screw. Cx going to keep an eye on it.
We serviced a
GE WASHER
Model GTW335ASN2WW
Near Pueblo, Colorado 81001
James
Job Details:
01/24/2025
Spanner nut was siezed on unit. Attempted removal for 40+ minutes. Nut would not come off. Called asu and they deemed unit unrepairable. Will contact customer within 24-48 hrs for next steps.
We serviced a
GE DRYER
Model GFD85GSPN1RS
Near Colorado Springs, Colorado 80924
Dvante
Job Details:
01/24/2025
Replaced the idler arm and rollers. Tested unit and no noises inside unit. Unit is working as designed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHV01
Near Central Point, Oregon 97502
Jeff
Job Details:
01/24/2025
Installed holder
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS1
Near Eagle Point, Oregon 97524
Jeff
Job Details:
01/24/2025
Installed parts ran diagnostic everything passed heater came on no error codes.
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6200QLAA
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
01/24/2025
"Replaced compressor, drier, vacuumed and charged unit to spec 78 g r600"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS26L3AF
Near Pueblo West, Colorado 81007
Domingo
Job Details:
01/24/2025
Replace defrost thermostat and board test it and its cooling
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Fountain, Colorado 80817
David
Job Details:
01/24/2025
"Installed ordered parts, ran calibration cycles, and diagnostic cycle. All ran good."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SG/AA
Near Colorado Springs, Colorado 80923
Mathew
Job Details:
01/24/2025
Replaced all parts. Test op all okay.
We serviced a
MAYTAG RANGE
Model MER7700LZ2
Near Pueblo, Colorado 81008
Domingo
Job Details:
01/24/2025
Check oven and it had loose wire connection by the power cord I tight those then check the temp by setting it at 350? and inside it was getting only 300? recalibrated to +30 re check it and set it at 350? and its 343? within range oven is working
We serviced a
MAYTAG DRYER
Model MED6630HC0
Near Pueblo West, Colorado 81007
James
Job Details:
01/24/2025
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL DRYER
Model WED9620HC2
Near Grants Pass, Oregon 97526
Jeff
Job Details:
01/23/2025
Found vent plugged repaired ran a diagnostic all passed
We serviced a
WHIRLPOOL WASHER
Model WFW9620HC3
Near Grants Pass, Oregon 97526
Jeff
Job Details:
01/23/2025
Went thru machine ran full diagnostic and found the boot makes some noise when starting spin cycle but then goes away. Will probably quite down a little after some more usage no errors did a factory reset. Working as should
We serviced a
KITCHENAID WALL OVEN
Model KOED530PPS00
Near Grants Pass, Oregon 97526
Jeff
Job Details:
01/23/2025
Installed new latch and ui tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ12
Near Grants Pass, Oregon 97527
Jeff
Job Details:
01/23/2025
Found switch stuck repaired
We serviced a
KITCHENAID COOKTOP
Model KCGD500GSS05
Near Grants Pass, Oregon 97526
Jeff
Job Details:
01/23/2025
Found lose connection repaired working as should
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Bend, Oregon 97701
Levi
Job Details:
01/23/2025
Found that door ceiling right hand side came loose and was preventing fridge from closing properly.
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
01/23/2025
Replaced the control board. Tested diagnostic mode. No error codes and leaks. Water is filling at the correct water level. Unit is operating as designed.
We serviced a
MAYTAG REFRIGERATOR
Model MRFF4236RZ00
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
01/23/2025
Installed module and switches all ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ18
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
01/23/2025
"Installed sleeve, no leak from fill tube"
We serviced a
MAYTAG REFRIGERATOR
Model MRFF4236RZ01
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
01/23/2025
Installed ice maker runs ok
We serviced a
MAYTAG WASHER
Model MVW6230RHW3
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
01/23/2025
"Replaced the agitator, gearcase, and cam. Tested diagnostic mode. No leaks and error codes. Unit is spinning and agitating with no squeaking noises. Unit is operating as designed."
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ09
Near Colorado Springs, Colorado 80915
Jerimiah
Job Details:
01/23/2025
Installed replacement OTR bulb. Unit check ok.
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
01/23/2025
7740618976 Called tech line deemed unit as design
We serviced a
WHIRLPOOL MICROWAVE
Model WOC54EC0HS03
Near Monument, Colorado 80132
Jerimiah
Job Details:
01/23/2025
"Mw waveguide and cover caught fire, called safety SR#7740723724, took pics, contacted Techline, gave info and pics, was instructed to given Cust info. Was given Techline SR#7740802077. Unit does seem repairable with at minimum an upper waveguide cover, max getting cover and new magnetron. Closing call."
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Tabernash, Colorado 80478
Antonio
Job Details:
01/23/2025
Installed new ignitor turn oven on realize that unit needs propane conversion.kit
We serviced a
KITCHENAID RANGE
Model KFDC506JSS01
Near Granby, Colorado 80446
Antonio
Job Details:
01/23/2025
"Found burners needed to be adjusted, so i trunned down flamec to allow proper gas flow to ignite. Unit tested good"
We serviced a
WHIRLPOOL DRYER
Model WED9620HC2
Near Aspen, Colorado 81611
James R
Job Details:
01/23/2025
Signed disclaimer. Tore apart and installed a repair kit. Also could see where drum was scraping the wall.Realigned front panel. Run a load in unit that is wet. Is not making the noise now. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS555SIHZ03
Near Pueblo, Colorado 81005
James
Job Details:
01/23/2025
Installed ordered parts tested ops all ckok left litmus
We serviced a
KITCHENAID DISHWASHER
Model KDTE404DSS1
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
01/23/2025
Replaced the vent assembly and control board. Tested diagnostic mode. No error codes or leaks. Unit passed diagnostics. Unit is operating as designed.
We serviced a
KITCHENAID RANGE
Model KSEG950ESS3
Near Colorado Springs, Colorado 80919
Jerimiah
Job Details:
01/23/2025
Installed replacement thermal sensor and controller. Unit check ok Cust will keep track of unit functionality.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS3
Near Fountain, Colorado 80817
Carlos
Job Details:
01/23/2025
"Unit was unleavened and tray was full of water, releveled unit runs ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ2
Near Albuquerque, New Mexico 87120
Larry
Job Details:
01/23/2025
CX complaint - Not washing properly - Inspected unit and found no error codes stored and the unit runs a diagnostic cycle successfully - Called techline to document (SR7740805040) - Unit is operating as designed
We serviced a
MAYTAG WASHER
Model MVW7232HC2
Near Peralta, New Mexico 87042
Larry
Job Details:
01/23/2025
CX complaint - F8E1 error - Inspected unit and found the valve failed - Replaced with pre-id part and tested good - Unit is good to go
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Albuquerque, New Mexico 87120
Larry
Job Details:
01/23/2025
CX complaint - Not draining - Inspected unit and found the drain pump failed - Installed pump from pre-id parts and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Albuquerque, New Mexico 87107
Larry
Job Details:
01/23/2025
CX complaint - DW not washing - Inspected unit and found the wash motor failed - Replaced with pre-id part and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ02
Near Bend, Oregon 97701
Levi
Job Details:
01/23/2025
"Replaced icemaker, tested, all checks okay"
We serviced a
WHIRLPOOL WALL OVEN
Model RB265PXK1
Near Grants Pass, Oregon 97526
Jeff
Job Details:
01/23/2025
Installed element tested machine working as should
We serviced a
WHIRLPOOL DISHWASHER
Model DU1015XTXB1
Near Albuquerque, New Mexico 87123
Jason
Job Details:
01/23/2025
Went to check unit out found counter has started sagging and is sitting on unit not allowing me to pull unit out. issue will have to be addressed before unit can be repaired. pics uploaded
We serviced a
MAYTAG WASHER
Model MVWB766FW1
Near Albuquerque, New Mexico 87111
Jason
Job Details:
01/23/2025
Installed parts listed ran calibration cycle and rapid wash unit opperation checks ok
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Tijeras, New Mexico 87059
Jason
Job Details:
01/23/2025
Installed part ran test cycle unit checks ok
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Albuquerque, New Mexico 87110
Jason
Job Details:
01/23/2025
Checked unit found control throwing drain error code before unit ever fills. control board likely badSC$139.95MPS$17.50LABOR$179.95CONTROL#W11410062$300.84TX$54.25TOTAL$692.4CX HAS TO THINK OVER REPAIRAuth code: 94FNUA$151.85
We serviced a
JENN-AIR WALL OVEN
Model JJW3430DS01
Near Basalt, Colorado 81621
James R
Job Details:
01/23/2025
Signed disclaimer. Removed console and checked all connections ok put back together and unit still has a F2E1 error code console is faulty. Gave customer estimate to repair. $1765.10 Will at this point just pay the service call. $189.95 auth code. 4KX9WHPlease fill out tech satisfaction survey. Thank You.
We serviced a
SAMSUNG REFRIGERATOR
Model RF31CG7200SRAA
Near Colorado Springs, Colorado 80903
Brandon
Job Details:
01/23/2025
"Replaced compressor, drier and vacuumed and charged to spec 86g r600 hass oqc passed"
We serviced a
SAMSUNG WASHER
Model WA54CG7150ADA4
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
01/23/2025
"Found obstruction in drain pump. Drain pump impeller is broken. Replaced drain pump, test op on OQC. All okay."
We serviced a
SAMSUNG RANGE
Model NX60T8711SS/AA
Near Pueblo West, Colorado 81007
Brandon
Job Details:
01/23/2025
Replaced ignitor and tested on all checks ok
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Pueblo, Colorado 81003
Mathew
Job Details:
01/23/2025
"Found seized motor, belt has snapped. Replaced fan motor assy and belt. Reassemble test op on OQC. All okay."
We serviced a
SAMSUNG DOUBLE WALL OVEN
Model NV51K7770DG/AA
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
01/23/2025
Replaced tcos and tested on all checks ok
We serviced a
KITCHENAID DOWNDRAFT VENT
Model KIRD861XSS0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
01/23/2025
"Needs a motor and capacitor part is discontinued (436015, 4360175) Cx paid SC, $139.95 CC Auth# RXJTKF"
We serviced a
JENN-AIR VENT HOOD
Model JXD7036YS0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
01/23/2025
Adjusted contact points on motor runs ok. If issue returns order W10833182. Cx paid SC $159.95 CC Auth# FRW393
We serviced a
WHIRLPOOL DRYER
Model WED86HEBW0
Near La Pine, Oregon 97739
Levi
Job Details:
01/23/2025
"Replaced element, tested, all checks okay. Paid in full on previous visit"
We serviced a
SAMSUNG WASHER
Model WA50R5200AV/A4
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
01/23/2025
"Need to collect for service fee $139.95, clogged drain pump"
We serviced a
JENN-AIR RANGE
Model JDRP548HL01
Near Tabernash, Colorado 80478
Antonio
Job Details:
01/23/2025
"Installed new acu's, cooling fans, and door hinges ran both ovens to 350? and units tested good"
We serviced a
JENN-AIR WALL OVEN
Model JMW2430LL03
Near Colorado Springs, Colorado 80904
Jerimiah
Job Details:
01/23/2025
"Unit still having original issues. Has had SMPS, APPL MGR, CONSOLE previously replaced. Called techline. Setting unit up for review. SR#7740654276"
We serviced a
PROFILE REFRIGERATOR
Model PCF23MGWCBB
Near Peyton, Colorado 80831
David
Job Details:
01/23/2025
Installed ordered parts. Ice dispenses but no water. tube in the door is frozen.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28T5001SR/AA
Near Pueblo, Colorado 81005
Mathew
Job Details:
01/23/2025
Replace evap fan. Test op all okay. Fan is now quiet. $189.95 CC Auth# WN9HKU
We serviced a
BOSCH DISHWASHER
Model SHE41CM2N/27
Near Pueblo, Colorado 81001
Domingo
Job Details:
01/23/2025
Upon arrival notice dishwasher legs were all of way up and dishwasher was leaning forward I raised the legs and ran a full cycle but it would leak after 30 min of running and no leaks were found
We serviced a
BOSCH DISHWASHER
Model SHP78CM6N/25
Near Pueblo, Colorado 81004
Domingo
Job Details:
01/23/2025
I try to raise legs it wont latch took all racks out still wont latch call tech line they said is a bad tub not repairable confirmation number 4104994329
We serviced a
BOSCH DISHWASHER
Model SHP78CM5N/25
Near Pueblo, Colorado 81005
Domingo
Job Details:
01/23/2025
Replace drain hose test it and it drain job completed put leak strip see picture
We serviced a
GE REFRIGERATOR
Model GNE25JMKGFES
Near Pueblo West, Colorado 81007
Mathew
Job Details:
01/23/2025
Replaced filter case assy. Test op all okay.
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Pueblo, Colorado 81001
James
Job Details:
01/23/2025
Installed ordered parts tested ops all ckok
We serviced a
SAMSUNG REFRIGERATOR
Model RF23M8070SR/AA
Near Pueblo, Colorado 81001
James
Job Details:
01/23/2025
Installed ordered parts tested ops all ckok
We serviced a
SAMSUNG WASHER
Model WA52A5500A
Near Pueblo, Colorado 81005
Domingo
Job Details:
01/23/2025
Check machine and is not making any noise ran a diagnostic mode and no noise out it in spin cycle and couldnt fine any noise test it the motor and test it good also test it drain pump and is clean no obstruction cant find nothing wrong with it told customer to record the noise for next time as it right now cant find nothing mechanically wrong with it
We serviced a
WHIRLPOOL DISHWASHER
Model WDPA70SAMZ3
Near Redmond, Oregon 97756
Austin
Job Details:
01/22/2025
Installed parts ordered. Tested unit all ops sat per factory spec. No leaks after installing sump assembly. Installed leak strip under unit.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Medford, Oregon 97501
Jeff
Job Details:
01/22/2025
Found water in tray triggering float cleaned out replaced parts tested machine for 25 minutes couldn't find any leaks at this time.
We serviced a
MAYTAG WASHER
Model MVWP575GW1
Near Ashland, Oregon 97520
Jeff
Job Details:
01/22/2025
Installed springs tested working as should
We serviced a
WHIRLPOOL DISHWASHER
Model WDPA70SAMZ3
Near Talent, Oregon 97540
Jeff
Job Details:
01/22/2025
Installed parts and switch tested ok can't
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ06
Near Prineville, Oregon 97754
Austin
Job Details:
01/22/2025
Installed parts ordered. Tested unit all ops sat per factory spec
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKV3
Near Medford, Oregon 97501
Jeff
Job Details:
01/22/2025
Removed debris from sump installed new pump tested working ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Ashland, Oregon 97520
Jeff
Job Details:
01/22/2025
Installed brackets still having issue on left side contacted tech line and was told that is normal on these machines file 7740793976
We serviced a
WHIRLPOOL RANGE
Model WFE535S0LZ3
Near Jacksonville, Oregon 97530
Jeff
Job Details:
01/22/2025
Installed fan tested machine working as should
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Colorado Springs, Colorado 80908
David
Job Details:
01/22/2025
"Checked washer, ran diagnostics very loud grinding noise at the end of the spin. Gears stripped in gear case. Replaced gear case, cam, actuator, and belt. Ran calibration and diagnostic cycles, running as expected."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Colorado Springs, Colorado 80923
David
Job Details:
01/22/2025
Replaced lid lock switch and strike. Tested and the lid is locking up.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Peyton, Colorado 80831
Charles
Job Details:
01/22/2025
Installed left door with water and electrical
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Colorado Springs, Colorado 80920
Dvante
Job Details:
01/22/2025
"Checked unit, found the dispenser isnt opening. Checked the dispenser and wasnt getting enough ohms. Replaced dispenser. Tested diagnostic mode, no error codes and leaks. The dispenser is opening. Unit is operating as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW10
Near Colorado Springs, Colorado 80907
Carlos
Job Details:
01/22/2025
Installed gasket all ok
We serviced a
WHIRLPOOL WASHER
Model WTW6150PW0
Near Monument, Colorado 80132
Dvante
Job Details:
01/22/2025
"Checked unit, found the lid isnt locking due to the strike broken. Went ahead and replaced the strike. Unit is locking. Tested diagnostic mode, no error codes and leaks. Unit is operating as designed."