We serviced a
MAYTAG DRYER
Model MED6230HW2
Near Bend, Oregon 97701
Levi
Job Details:
12/19/2024
"Replaced HMI, tested. All checks okay"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Colorado Springs, Colorado 80907
David
Job Details:
12/19/2024
"Installed ordered parts, ran calibration cycle and diagnostic cycle, ran as expected."
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ2
Near Colorado Springs, Colorado 80905
Carlos
Job Details:
12/19/2024
"Spoke with Nick at Whirlpool Commercial Tech support on 12/19/24 10:50a.m. Comercial tech support does not provide SR#. Cx complaint of clothes not wringing out clothes is due to error code F3E1, user error cx tenants using too much soap causing unit to think there is too much water in unit and stoping before load is use. Cx needs to make sure tenants are using strictly HE liquid soap to the amount equal to one load. Installed water valve runs ok. Cx paid LB $179.95 CC Auth# EEY4EH"
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ2
Near Colorado Springs, Colorado 80905
Carlos
Job Details:
12/19/2024
"Spoke with Nick at Whirlpool Commercial Tech support on 12/19/24 10:50a.m. Comercial tech support does not provide SR#. Cx complaint of clothes not wringing out clothes is due to error code F3E1, user error cx tenants using too much soap causing unit to think there is too much water in unit and stoping before load is use. Cx needs to make sure tenants are using strictly HE liquid soap to the amount equal to one load. Installed water valve runs ok. Cx paid LB $179.95 CC Auth# EEY4EH"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS11
Near Bend, Oregon 97702
Levi
Job Details:
12/18/2024
"Replaced door seals, tested good"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ2
Near Bend, Oregon 97702
Levi
Job Details:
12/18/2024
Replace pump assembly and water inlet. Tested all checks okay
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Eagle Point, Oregon 97524
Jeff
Job Details:
12/18/2024
Arrived no one home no answer Rick called and customer canceled
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS00
Near Prineville, Oregon 97754
Austin
Job Details:
12/18/2024
Installed new board to unit. Tested all ops sat per factory. Unit harvest and fills with water. No error codes for fridge or ice maker.
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Prineville, Oregon 97754
Austin
Job Details:
12/18/2024
Installed parts ordered. Tested unit all ops sat per factory spec.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Medford, Oregon 97501
Jeff
Job Details:
12/18/2024
Installed parts and Found hose connection to fill valve loose retightened tested and monitored no more leaks working as should
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS04
Near Bend, Oregon 97702
Levi
Job Details:
12/18/2024
"Replace dual water valve and bucket, cleaned up all the ice buildup then tested. I'll test check okay"
We serviced a
MAYTAG REFRIGERATOR
Model MSS25C4MGZ06
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
12/18/2024
"Removed and replaced components, tested operation, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80918
Dvante
Job Details:
12/18/2024
"Replaced suspension rods, tested the diagnostic mode. No loud thumping and knocking noise. Unit is working as designed"
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS2
Near Fountain, Colorado 80817
Carlos
Job Details:
12/18/2024
"Cx has water built up in tray, causing leak sensor to go off. Dishwasher was unleveled leaning forward, raised feet, cx will observe. Home floor is too high and counter is too low to remove unit to inspect other areas, making it inaccessible."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT104TFDW03
Near La Junta, Colorado 81050
James
Job Details:
12/18/2024
Replaced preordered parts for temp concerns tested ops all ckok
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Colorado Springs, Colorado 80921
Dvante
Job Details:
12/18/2024
"Checked unit, customer explained the temperature drops when timer is on. Not baking properly. Tested the temperature and saw the temp staying steady. The main board is going to cycle both elements when losing temperature. Temp will rise and go down keeping the set temperature steady. No issues with unit"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ03
Near El Jebel, Colorado 81623
James R
Job Details:
12/18/2024
Signed disclaimers.Unit was unplugged when I arrived. Put unit into service diagnostics. test 5 defrost 1.5 amps good. so defrost cycle is good. Checked frz compartment thermistor not reading. Removed control checked wire connections found the one for thermistors no snapped in place connected good then took a reading 3.93k ohms at 62.7 degrees. Frz thermistor 5.39k ohms at 53.6 degrees so both thermistor are working. Checked evap thermistor 4.53k ohms so is working. Checked compressor amps .79 good. Condenser fan is running. Evap fan and dampner are also working. Starting to cool down in Frz and F.F. areas. All light switches are working. Operating as should. for future reference leave unis running if possible.
We serviced a
MAYTAG DRYER
Model MED7230HW1
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
12/18/2024
"SR- 7740558839 unit needed software update, completed cx will observe"
We serviced a
KITCHENAID DISHWASHER
Model KDTE404DSS0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
12/18/2024
Installed adjuster and spray arm all ok
We serviced a
MAYTAG WASHER
Model MVW5435PW0
Near Los Lunas, New Mexico 87031
Larry
Job Details:
12/18/2024
CX complaint - Damaged colthes - Inspected unit and found the agitator came loose - Secured agitator with loc-tite - Ran test cycle and tested good - Unit id good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ02
Near Albuquerque, New Mexico 87123
Jason
Job Details:
12/18/2024
Installed compressor and evap. charged unit up pressures and frost pattern check good. unit opperation checks ok
We serviced a
MAYTAG RANGE
Model MGR6600PZ1
Near Peralta, New Mexico 87042
Larry
Job Details:
12/18/2024
Installed door glass - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Socorro, New Mexico 87801
Larry
Job Details:
12/18/2024
"Installed parts listed, calibrated and ran test cycle - Unit is operating as designed"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM1
Near Rio Rancho, New Mexico 87124
Joe
Job Details:
12/18/2024
"Cx complaint, Dishwasher doesn't wash dishes. Inspected unit, found wash motor bad. Replaced sump assembly and tested on quick wash. Unit washing fine nowAdvised cx about survey"
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Los Lunas, New Mexico 87031
Larry
Job Details:
12/18/2024
"Installed parts listed, ran test cycle and tested good - Unit is good to go"
We serviced a
KITCHENAID DISHWASHER
Model KUDI01TJBL1
Near Redmond, Oregon 97756
Austin
Job Details:
12/18/2024
Unit has a cracked tub in the bottom front corner. Unit is unrepairable.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT148FZDB
Near Colorado Springs, Colorado 80910
Scott
Job Details:
12/18/2024
installed listed parts recharged checked op ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB08
Near Los Lunas, New Mexico 87031
Larry
Job Details:
12/18/2024
Installed ice maker and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model WED8127LW1
Near Rio Rancho, New Mexico 87144
Joe
Job Details:
12/18/2024
"Cx complaint, light works intermittently. Replaced door switch ordered last visit. Tested light multiple times. Light working as designedAdvised cx about survey"
We serviced a
WOLF RANGE
Model DF60650CG/S/P
Near Colorado Springs, Colorado 80906
Jerimiah
Job Details:
12/18/2024
Installed rework kit. Unit check ok.
We serviced a
JENNAIR WALL OVEN
Model JJW2430DS02
Near Rio Rancho, New Mexico 87144
Joe
Job Details:
12/18/2024
"Cx complaint, getting key stuck error. Inspected unit, unable to clear error. Advised cx they need new console. Cx declined estimateAdvised cx about survey. Cx paid diagnostic fee by credit card Authorization number CNCX43"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
12/18/2024
"F7E4, F5E4 error codes upon arrival, slider tabs have worn, tub is unable to engage, removed and replaced slider and clutch, ran unit through DLMS and diagnostic cycles, working well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG RANGE
Model NX60A6511SS/AA
Near Colorado Springs, Colorado 80907
Mathew
Job Details:
12/18/2024
"Found broken bake igniter. Replace broken bake igniter. Test op in bake, all okay."
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Colorado Springs, Colorado 80925
Mathew
Job Details:
12/18/2024
Found faulty control board. Replace control board. Test op on OQC. lol okay.
We serviced a
SAMSUNG MICROWAVE
Model MS19M8000AS/AA
Near Monument, Colorado 80132
Dvante
Job Details:
12/18/2024
"Checked unit, saw the door not opening properly. Replaced the body latch. Door is opening properly. Unit is working as designed"
We serviced a
SAMSUNG COOKTOP
Model NA30N6555TS/AA
Near Monument, Colorado 80132
Dvante
Job Details:
12/18/2024
"Checked unit, saw the middle burner turning on improperly. Replaced the burner, igniter and cap. Burner is turning on properly. Unit is working as designed."
We serviced a
SAMSUNG RANGE
Model NX60A6511SG/AA
Near Peyton, Colorado 80831
Brandon
Job Details:
12/18/2024
Replaced board all checks ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB86004MAA
Near Colorado Springs, Colorado 80909
Mathew
Job Details:
12/18/2024
Replace leaking filter case and dispenser. Test op all okay.
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Rifle, Colorado 81650
James R
Job Details:
12/18/2024
Printed labels took pics ready to send.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHV00
Near Colorado Springs, Colorado 80923
Charles
Job Details:
12/18/2024
"Installed control board.Service fee $139.95Labor $229.95MPS $14.50Part $312.89Tax $25.66Total $722.95Paid in full auth 3X3WL9, EF4H4P, L93RMJ"
We serviced a
JENN-AIR RANGE
Model JGRP436WP02
Near Albuquerque, New Mexico 87122
Jason
Job Details:
12/18/2024
Installed control checked heat cycling and temps unit opperation checks ok at this timeAuth code: 9UF4XW$227.80
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS03
Near Central Point, Oregon 97502
Jeff
Job Details:
12/18/2024
Customer meet me at door and said she canceled service days ago. Doesn't want repaired. Do to out of warranty
We serviced a
MAYTAG WASHER
Model MVWB835DW3
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
12/18/2024
"Removed and replaced UI console, programmed and tested unit through diagnostics, working well now, no leaks, installed litmus strip. Total due was previously paid."
We serviced a
WOLF RANGE
Model n/a
Near Colorado Springs, Colorado 80908
Charles
Job Details:
12/18/2024
Going into diagnostics when not in use. Touchscreen part number 806828Service fee $159.95Labor $269.95MPS $14.50Part $597.50Tax $49.00Total $1090.90Declined estimate at this time. 30 day estimate. Paid service fee $159.95 autho 994MVM
We serviced a
ELECTROLUX REFRIGERATOR
Model EW23BC85KSSW
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
12/18/2024
"unit had a frozen water line, called tech support unit is building up ice on the back wall of the unit , tech said there is no fix for that, thawed the line and put stuff to keep away form the wall cust has been advised"
We serviced a
FIVESTAR RANGE - GAS
Model n/a
Near Florissant, Colorado 80816
Ralph
Job Details:
12/18/2024
INSTALLED PART AND UNITY CHEC KED OKAY
We serviced a
SHARP MICRO DRAWER
Model KB6524PSYD
Near Monument, Colorado 80132
Jerimiah
Job Details:
12/18/2024
Installed replacement magnetron. Unit unit check OK $252.94 CC Auth# CFRHXW
We serviced a
JENN-AIR DISHWASHER
Model JDB9000CWP2
Near Albuquerque, New Mexico 87111
Jason
Job Details:
12/18/2024
un-plugged unit and plugged it back in unit opperation checks okAuth code: C44C3U$151.85
We serviced a
MIELE RANGE
Model KMR1136-1G
Near Eagle, Colorado 81631
Erik
Job Details:
12/18/2024
install spark node/ test: ignition and flame present/ shuts off immediately: FAILcall Miele TAG: flame monitor 10126991 ($698.11)CX will call Miele for consession requestopen unit and check continuity on spake harness - GOODJOB COMPLETE
We serviced a
JENNAIR WALL OVEN
Model JJW9430DDS
Near Colorado Springs, Colorado 80924
Charles
Job Details:
12/18/2024
"Door hinges failed, original JennAir, parts no longer available. Paid service fee $159.95 autho C4993H"
We serviced a
JENN-AIR WALL OVEN
Model JMW2430LL03
Near Colorado Springs, Colorado 80904
Jerimiah
Job Details:
12/18/2024
"Installed replacement components. Unit check ok, if problem persists of console blinking out, needs smps board replaced. Cust will keep track of unit functionality."
We serviced a
ASKO DISHWASHER
Model DBI664
Near Woodland Park, Colorado 80863
Ralph
Job Details:
12/18/2024
"called tech support we did a reset and unit is now working, cust to monitor..autho no. 93R3X4"
We serviced a
DCS RANGE
Model CS-364GLSS-L
Near Florissant, Colorado 80816
Ralph
Job Details:
12/18/2024
UNIT IS WORKING AS INTENDED.
We serviced a
JENNAIR REFRIGERATOR
Model JFX2897DRP02
Near Colorado Springs, Colorado 80920
David
Job Details:
12/18/2024
"Installed compressor and valve, evacuated, and charged system. It is cooling down. There is a noise in the freezer from the evap motor area. The tabs that hold things together are broken off. Cx may call again for this."
We serviced a
MONOGRAM MICROWAVE OVEN
Model ZSB9232N2SS
Near Snowmass, Colorado 81654
Sean
Job Details:
12/18/2024
checked un it MN/SN POPcustomer signed disclamer.tested unit cound not reproduce problem.reset unit disconnected power.opened unit and checked for loose wire.found the ribon wires where not seated fulley.checked all fuses and thermal switches. found all tested good. found no error codes on unit.reassembled unit and tested. unit started and ran without reproducing problem.dign = unit had unsecured ribbon wire.
We serviced a
PROFILE WASHER
Model PTW605BSR1WS
Near Avon, Colorado 81620
Erik
Job Details:
12/18/2024
RENTAL PROP - ACCESS WITH DOOR CODEconnect to smartHQ service: F26 (inactive) out of balance final spin - TOO MUCH OR TOO LITTLE LOAD IN BASKETperform spin test: 800 rpm - OK* see quick picsuser error loading issue call GE customer relations for instruction on loading/ use and careCX not available for signature
We serviced a
PROFILE WASHER
Model PTW605BSR1WS
Near Avon, Colorado 81620
Erik
Job Details:
12/18/2024
RENTAL PROP - ACCESS WITH DOOR CODEconnect to smartHQ service: F26 (inactive) out of balance final spin - TOO MUCH OR TOO LITTLE LOAD IN BASKETperform spin test: 800 rpm - OK* see quick picsuser error loading issue call GE customer relations for instruction on loading/ use and careCX not available for signature
We serviced a
GE DRYER
Model GFD14ESSNWW
Near Aspen, Colorado 81611
Sean
Job Details:
12/18/2024
"checked unit MN/SN POPcustomer signed disclamer.opened unit checked basket good.closed and sarted. basket is rubbing the right hand side panel. unplugged unit and removedtop panel, controle panel, and front cover to gain acsess to the R side panel.found where side panel was pushed in at.pushed panel back into square.reassembled unit restored power and tested unit no longer rubbing .tested unit good.thank you and please go online to D-3 A/OK appliance and fill out a tech servey."
We serviced a
BOSCH WALL OVEN
Model HMC80252UC/05
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
12/18/2024
"after pricing the repair it would have been over 1000.00, so cust does not want to repair"
We serviced a
GE DISHWASHER
Model GDT695SSJ0SS
Near Vail, Colorado 81657
Erik
Job Details:
12/18/2024
disconnect comm cable to UI and plug back in - UI woke up and is functioningconnect to smartHQ service: apply software update multiple errors with MCB (parametric update should fix)* see quick picsCX to test - MCB WD21X24901(suspected corrosion)$199.95 PAID autho#FR3TN3JOB COMPLETE
We serviced a
VIKING RANGE
Model VESO530SS
Near Colorado Springs, Colorado 80906
Jerimiah
Job Details:
12/18/2024
Installed replacement parts and rework. Unit check ok charged labor as quoted chk#3392 $249.00 CK Auth# WHM99T
We serviced a
GE WASHER
Model GFW550SSN5WW
Near Colorado Springs, Colorado 80918
David
Job Details:
12/18/2024
"Ran diagnostics, Diagnostics codes 38, 26, 92, 39, 8, 32. Ran through the diagnostics that they correspond to, all good, cleared codes. Ran a couple of cycles, then checked for error codes again, none at this time."
We serviced a
MAYTAG RANGE
Model MER7700LZ2
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
12/18/2024
"SR-7740560164 User wear and tear. Called Assurant techline glass top has flakes coming off. purely cosmetic. Handle on door was loose, tighten handle all ok."
We serviced a
WHIRLPOOL WASHER
Model WTW4850HW1
Near La Pine, Oregon 97739
Levi
Job Details:
12/18/2024
Replaced control board tested good
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA
Near Peyton, Colorado 80831
Brandon
Job Details:
12/18/2024
Replaced ice maker and cycled all checks ok
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Los Lunas, New Mexico 87031
Larry
Job Details:
12/18/2024
When installing the latch I found the machine infested with mice - Called Assurant to document (24001040299DF) - Assurant said we will be paid for today but not in the future becaust they cancelled further warranty - Tech has part
We serviced a
WHIRLPOOL DRYER
Model WED5050LW0
Near Colorado Springs, Colorado 80921
Charles
Job Details:
12/18/2024
"Open element, need part 279838, pick up part from shop and return, installed element and tested"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ
Near Colorado Springs, Colorado 80907
Carlos
Job Details:
12/18/2024
"Installed Sump assembly and control board runs all ok. Called Techline 7740564095, cx states dishwasher does not dry properly. Looked at wax motor reservoir no rinse aid present, instructed cx to use rinse aid to dry dishes."
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KWH1
Near Carbondale, Colorado 81623
James R
Job Details:
12/18/2024
Signed disclaimer. Removed outer door panel and replaced ACU and outer door asy. Reassembled unit test run service diagnostics test no codes present let go thru cycle. Went thru fine no issues and no error codes when done. Operating as should. Please fill out tech satisfaction survey. Thank You. Put a leak board under unit and took pic.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Redmond, Oregon 97756
Austin
Job Details:
12/18/2024
Installed parts tested unit all ops sat per factory spec.
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ0
Near Rifle, Colorado 81650
James R
Job Details:
12/18/2024
Customer signed disclaimer. Removed outer panel and replaced ACU then tested in service diagnostics test. No error codes when done. Operating as should. Put a leak board under unit and took pic. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Grants Pass, Oregon 97526
Jeff
Job Details:
12/17/2024
Found another cut wire. repaired wire and tested machine working as should
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Prineville, Oregon 97754
Austin
Job Details:
12/17/2024
Installed part tested unit. All ops sat per factory spec. Installed leak strip under drain pump.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Bend, Oregon 97701
Levi
Job Details:
12/17/2024
Reset power and unit is now working fine.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Bend, Oregon 97701
Levi
Job Details:
12/17/2024
Reset power and unit is now working fine.
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ2
Near Grants Pass, Oregon 97526
Jeff
Job Details:
12/17/2024
Installed all parts tested machine and ran diagnostic no error codes and no leaks working as should
We serviced a
WHIRLPOOL RANGE
Model WFE535S0LZ3
Near Pueblo, Colorado 81005
James
Job Details:
12/17/2024
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHW04
Near Pueblo West, Colorado 81007
James
Job Details:
12/17/2024
Cust complaint of smell in unit and ui issues. Found loose wire at ui causing intermittent ui failure. Secured wire and tested all ops test good. Went through entire system found no evidence of refrigerant leak. All ops test good. Advised cust toput baking soda and whirlpool air filter in unit to absorb unwanted smells
We serviced a
WHIRLPOOL DISHWASHER
Model WDPS5118PM0
Near Colorado Springs, Colorado 80903
David
Job Details:
12/17/2024
Checked dishwasher. reset control. Tested and is operating as expected
We serviced a
WHIRLPOOL DISHWASHER
Model WDPS5118PM0
Near Colorado Springs, Colorado 80903
David
Job Details:
12/17/2024
"Checked dishwasher, has an E1 error code, no water. The dishwasher does not have water hooked up."
We serviced a
WHIRLPOOL DISHWASHER
Model WDPS5118PM0
Near Colorado Springs, Colorado 80903
David
Job Details:
12/17/2024
"Checked dishwasher, over filling, drain pump not running, plug off pump, reattached. Tested and is running good."
We serviced a
KITCHENAID RANGE
Model KSEG700ESS6
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
12/17/2024
"Wire terminal not fully engaged within connector, corrected and tested unit, working and heating well. Programmed setting for customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDPA70SAMZ3
Near Colorado Springs, Colorado 80920
Dvante
Job Details:
12/17/2024
"Replaced control board and door. Tested diagnostic mode. No error codes, no leaks. Unit is heating. Unit is working as designed."
We serviced a
MAYTAG DRYER
Model MED6500MBK0
Near Colorado Springs, Colorado 80918
Charles
Job Details:
12/17/2024
"No noise with empty dryer, remove drum, lubricant rollers and pulley."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT540HAMZ0
Near Colorado Springs, Colorado 80919
Dvante
Job Details:
12/17/2024
"Replaced the pump & motor assy. Tested diagnostic mode, no error codes, no leaks. Unit is working as designed."
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Peyton, Colorado 80831
Aaron
Job Details:
12/17/2024
"Customer complains of long dry times, check vent error appearing during use, inspected unit, temperatures are good, with temperature reaching 230f, unit has good push, check vent code appeared, disconnected vent hose and code did not show up, thermistor is good. Discussed situation with techline, recommend having vent professionally cleared, unit registers air restriction, advised customer of usage and mixed cycles. Advised customer of 5 star survey. SR7740557158"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Grants Pass, Oregon 97527
Jeff
Job Details:
12/17/2024
Installed parts and found wire broking under machine repaired tested working as should
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
12/17/2024
Installed capacitor ran test all ok
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Grants Pass, Oregon 97527
Jeff
Job Details:
12/17/2024
Installed parts and Found broking wire under machine repaired tested working as should
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PBS00
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
12/17/2024
"Scratches on microwave cavity door, removed and replaced door, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
12/17/2024
"Circulation motor is shorted out, no water movement, removed and replaced motor sump assembly, tested unit, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Colorado Springs, Colorado 80917
Dvante
Job Details:
12/17/2024
"Checked unit, saw the wires not hooked up to the main board properly. Probably came from the factory not wired. Put the wire back on. Unit is powering on. Unit is working as designed"
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
12/17/2024
"Inspected unit, heating element flume tab is rattling against the back wall, corrected and monitored, working and heating well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF954CIHZ03
Near Colorado Springs, Colorado 80915
Ralph
Job Details:
12/17/2024
installed listed parts and unit checked okay
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDM05
Near Belen, New Mexico 87002
Larry
Job Details:
12/17/2024
CX complaint - Ice Maker not working - Inspected unit and found a pin loose on the IM harness - Secured pin in harness and IM tested good - Unit is operating as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM12
Near Albuquerque, New Mexico 87105
Larry
Job Details:
12/17/2024
CX complaint - Not making ice or dispensing water - Inspected unit and found the isolation valve harness disconnected - Connected valve and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Rio Rancho, New Mexico 87144
Joe
Job Details:
12/17/2024
"Cx complaint, leaking from bottom. Inspected unit, ran on rinse and spin and normal. Filled and let agitate. No leaks found and everything was dry. Unable to duplicate issue. Unit good to goAdvised cx about survey"
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Albuquerque, New Mexico 87105
Larry
Job Details:
12/17/2024
Installed suspension and tested good - Unit is good to go
We serviced a
JENN-AIR WALL OVEN
Model JMW2430IL03
Near Colorado Springs, Colorado 80921
Jerimiah
Job Details:
12/17/2024
Replaced ground wire behind bulkhead. Unit check ok
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model DFSS9VKBASS
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
12/17/2024
"the fingers of the icemkr were stuck in ice so the unit would not cycle, pulled ice mkr and thawed ice and put back in and the unit cycled and filled, told cust to montor the unit and call back if needed...autho no. EV3RA3"