"Temp, frost pattern, fans, all check ok. Left temp sensor in freezer, will return in a week to get and check temp patterns. Collected service call fee"

Parts installed check ok

Ran calibration unit back to normal hot water getting supply

Installed door. Still need other side door. Part neededDA91-05481G - door right; ordrng 1 DA91-05481G (Door)

Need to order new partsDA97-18859A- icemakerDA97-17285B- tray; ordrng 1 DA97-18859A (Icemaker) and 1 DA97-17285B (Tray)

"Cust said he is getting ice build up in fridge causing fan to make noise, called techline for troubleshooting. They had me put unit in extended Defrost mode. Also we need to replace evap cover and then reposition the Defrost sensor. Service charge 119.95Evap cover da97-13757a 195.02Labor 129.95; ordrng 1 da97-13757a (Evap cover)"

"Installed new parts, called TL, they walked me through steam cycle and all checks ok. Main PCB has bad programming. Need to replace via Samsung TLDE92-03960E; ordrng 1 DE92-03960E (Control)"

"Found agitator rubbing against basket during operation. Reseated and secured. Tested all ops, all ckok"

"Found unit needing cold control 5304513033 67.04+tax, defrost timer 5304518034 52.88+tax, sc 119.95, labor 174.95, mps 12.50. Total: 436.83, 261.88 collected today remainder due on completion ; ordrng 1 5304513033 (Cold control) and 1 5304518034 (Defrost timer)"

still need spray arm; ordrng 1 DD82-01309A (spray arm)

installed part and unit checked okay

found leak in the fridge evap area; ordrng 1 DA96-01140B (fridge evap) and 1 da81-06006b (filter drier)

Check unit. Found a piece of plastic broke from lower spray arm. It is not effecting the spray arm as the clips to hold it are still intact. Let cust know she should be able to continue using as is. Let her know if spray arm is falling off then it will need replaced. Would not charge Labor to install spray arm if customer needs.Service charge 119.95Spray arm W11101428. 82.70

installed control and led modules unit checkd ok

Needs compressor start switchPart# W11547180 start switch ; ordrng 2 W11547180 (Start switch)s

unit has bad heat pump; ordrng 1 12008381 (heat pump)

installed parts and unit checked okay

"installed listed parts, unit checked okay"

"checked unit found simmer was high on most burners, adjusted simmer height unit opperation checks ok at this time"

"checked unit found gearcase is noisy, gearcase, belt and cam needed; ordrng 1 W11423758 (gearcase) and 1 W10721967 (splutch) and 1 W11239857 (belt)"

"Checked unit found that unit is locking up plus cx has been having issues with clock not keeping proper time, there is a service pointer for issue. can not get unit to connect to wifi. panel needed; ordrng 1 W11297728 (console)"

checked unit found control and ui both not opperating properly both are needed; ordrng 1 W11105847 (console (wht)) and 1 W11305293 (control)

"checked unit i had adjusted front of unit a little too high last time out. re leveled unit door opening and closing is normal opperation for this unit, cx does not want doors to slam open when opened I adjusted level as much as possible but cx sais still unexceptible"

"checked unit found ice bin flap is binding causing crushed ice to come out when cubed is selected, also ice paddle is sticking ice door assy ans bin both needed; ordrng 1 WPW10558423 (ice bin) and 1 W11423782 (ice door)"

installed part and unitn chekced okay

Check unit. Found unit making slight ticking noise. Disassembled unit. All parts are in place and are in good shape. Determined noise is just from the moving parts of unit and cannot be fixed. Let cust know noise is completely normal and will not affect the use of the unit.

Installed parts and all checks ok

Install previous ordered drain motor and test operation.

Repairs to door frame to quiet noise when opening door. Remote start and cavity lamp turns on and won't turn off. Tech had homeowner unistall app. Now we can't get unit to communicate for reinstall. ; O-emld tckt

"installed listed parts and unit checked okay, did a funds reversal of 23.22, due to wrong part number given to me by great plains"

reinstalled screws an unit feels snug

Washer has bad bearings. Parts needed-W10253866 - rear tubWP8181673 - gasketRepair est - $1215.17. Collected for SC $119.95Customer not going to repair at this time

Tech was assigned as a helper;

will need listed part; ordrng 1 00499780 (transformer( travis autho'd))

Found unit with noisy compressor and unit pulling .3 amps when running indicating potential leak needs compressor MSV172AL2J/SM3 and dye drier da81-06006b pls allow 3 hrs; ordrng 1 MSV172AL2J/SM3 (Compressor) and 1 Da81-06006b (Dye drier)

Food loose connection on the incoming power to the terminal fixed check ok

Found e9 error codeMotor heater#12008381$157.64Tax12.9312.50Sc119.95Labor195.95Total498.97Cx will think about it

Check unit. Found ice maker not cycling. Will need to replace ice maker to repair. Service charge 119.95Labor 89.95Ice maker da97-07365g 210.08; ordrng 1 da97-07365g (Ice maker)

"Found fill valve extremely loud, otherwise working. Part needed for repairDA97-21938A - filter valve asm; ordrng 1 DA97-21938A (Filter valve asm)"

Remove and replace dual valve. Test and check. Ice maker is now filling properly. Let cust know to allow 24h for ice production to start.

Install previous ordered drive system parts and test lo and hi speed spin cycle. Homeowner satisfaction.

Cust said unit is not washing. Stops mid cycle. Check unit. Found 8c error for mems sensor. All connections good. Will need to replace main pba; ordrng 1 Dc92-02648a (Assembly kit main pba)

Install previous ordered lid and verify proper function.

Cust said unit wouldn't stay balanced and would keep filling with water. Checked unit for possible causes of off balance. Unit is running smooth. Went over proper loading with cust and cycle selection. Also calibrated unit. Only errors in system were F0e5 for over loading and F0e3 for off balance. Cust will try recommendations and call back if off balance issues are still there

Motor#W10591569$240.76Tax19.7412.50Sc119.95Labor149.95Total542.90; ordrng 1 W10591569 (Motor)

Installed new element and tested. All checks ok. Customer signed wavier and leak detector installed

Parts installed check okay

"unti has a faulty contorl will need ot be repalced, cust not repairing"

Remove and replace heater. Test and check. All checks ok.

Loose wire at drain pump. Secured and Filled unit with 6 heavy bath towels for testing. Ran rinse and spin test all ops test good

Tested all ops all operations ckok. No issues found with unit. Collected 119.95

Bad ice maker ice makers going to be replaced by prior company that came out under warranty

Installed door unit checks ok

Power cord to ACU was not connected correctly connected power cord to ACU and now is working

Need to return adjuster kit that was ordered and order new parts. Parts neededWPW10546503 - rack adjuster (2) $50.20Customer already paid for SC- 119.95 Part that needs to be returned $75 +tax. Need to collect additional $33 before ordering new part and labor $129.95 after service is complete. ; ordrng 2 WPW10546503 (Rack adjuster)s

Replace lid switch and timer for 2nd time. No-fix in Permanent Press cycle. Tech contacted HomeSmart to let them know unit is non-repairable. ( multiple attempts )

Found loose connection to drain pump fixed check ok

"Cust said she has not had issue with water randomly dispensing anymore but ice maker is still not working. Cust said this was original reason for call and said that unit needs to be replaced. Called techline to talk about issues with fridge. After troubleshooting with techline. Determined water fill line is frozen and not allowing ice maker to fill. Will need to replace. File#7732961735. Cust said all previous calls were covered but said office told her to setup a new call with whirlpool. Whirlpool did not send auth to cover service. This call was supposed to be a call back, did not charge her a service charge. As I was just out here a week ago so it should be considered a call back. Whirlpool had given us a concession to cover parts. I told cust I would not charge her labor for her troubles. Cust called whirlpool to see if she could get auth for parts even though she already did on previous ticket. I waited for an hour and did not get an answer so cust will call with auth but if they were covered on prev ticket not sure why it was closed.Fill tube W10815476 Heater W11226501; ordrng 1 W11226501 (Heater) and 1 W10815476 (Fill tube)"

Repairs to wiring harness and test operation.

installed unit

DA97-14474A - ice tray; ordrng 1 DA97-14474A (Tray)

Charging for part and tax ordering parts and res...; ordrng 1 12008381 (Motor)

preordering part; ordrng 1 12025340 (harness)

Asurion asked for serial number. HR70921744. There is an uploaded picture of model/serial tag.

Oven model serial HBL57M52UC/02 ser: 990700096. This will be the unit that received the fuse.

Replace evaporator cover and ui panel and is working at this time if customer calls back she needs to call whirlpool because motherboard in back is no longer available

Installed ordered part tested ops all ckok no leaks observed. Advised house keeping to use less soap to help with oversuding)

installed listed parts and unit chekced okay

installed control Spoke with techline unit operation checks ok at this time. was not able to fill with water to fully check cx had unit on back porch when part installed SR7732973076

checked unit found unit is cycling on high limit t-stat. thermal fix kit needed; ordrng 1 279769 (thermal cutoff)

"checked unit found that noise is normal opperation and sounds like refrigerant flowing through capilary tube. adjusted doors so they are evan, unit checks ok"

Door panel was rejected by cust due to scratch. Will need to order door panel again all other parts will be installed next visit need 2 hrs ; saved tckt

"Found rollers squealing, replaced with pre-ordered repair kit. All ops test good"

installed lid lock unit opperation checks ok

Found broken wire at drain pump fixed and tested. All ops test good

installed console unit opperation checks ok

Replaced sump and is working

"Found drain pump intermittently not draining as designed. Needs drain pump DC96-01703G stacked unit, need 2nd man; ordrng 1 DC96-01703G (Drain pump assem (needs autho))"

Replaced sump and is working

Cleared all water and installed new pump. Tested and all checks ok

Tech install homeowner purchased control. Now fan speed sensor is open. Instruct homeowner to purchase fan complete.; snapped 3 QuickPics

checked unit found temps to be 120F-300F unit still not properly cycling thermal fix kit needed; ordrng 1 W10900067 (thermal fix kit)

installed upper and lower cooling fans unit opperation checks ok

Cust dispenser is not opening during the cycle. I ran test mode multiple times and dispenser is opening everytime i test. No errors stored in system. Dispenser does not ohm properly. Let cust know since it's working at this time will be hard to say exactly cause. Giving quote for dispenser and control. Let cust know dispenser is most likely cause. Let cust know to test unit further to ensure nothing is blocking dispenser. Cust will call if they decide to repair. Service charge 119.95Dispenser W11032769 125.22Control WPW10352582. 289.86Labor 89.95

Says unit is not getting hot enough. No one here to communicate issues with oven with. I checked oven functions and monitored Temps. Actual temp was about 10deg lower then set temp after watching for about 30min. Calibrated oven. Watched unit heat. Unit is now holding set temp.

Tested I got a noisy clutch assy need to reorder the part; ordrng 1 Dc97-16984a (Clutch assy)

Unit have shorted UI not responding ordering parts and res...; ordrng 1 DG96-00850D (Touch pad) and 1 DG92-01232C (Pcb) and 1 DG61-02054A (Holder)

Unit is working in good order possible Cx change the setting from deli to meat on the drawer side. All check ok called GE get second opinion .

Ticket said lights not working. Checked unit all lights are working. Office said they will contact tenant to get reason for call as all functions seem to be working properly on unit.

"Customer was switching out new filter and new took off the cap from the new filter. The cap got stuck in, i was able to remove and insert new filter. All checks ok.Collected $119.95 svf"

"Unit when baking makes pantry room hot and bottom drawer below oven hot, verified temps. Unit check ok. Cust will contact home builder for solutions for issue at hand."

Unit getting F6E6 lost comm error. Also problems with oven baking left side faster than right side in upper oven. Gasket looks good but will try replacement. Please order below.W11448962 Copernicus W11216658 signal harnessW11449303 consoleW10739089 gasket; ordrng 1 W11449303 (Console) and 1 W11448962 (Copernicus) and 1 W10739089 (Upper gasket) and 1 W11216658 (Signal harness)

Replaced door latch and is working

"unit has a bad board, thats no longer available, cust going to see if he can locate the board"

"unit requires new parts, display is missinf led lights and retainer broke in the freezer area; ordrng 1 7009861 (control) and 1 7009399 (retainers)"

installed part and unit checked okay

Installed new parts and all checks ok. Need to send back order rail asm. ; ordrng 1 WPW10546503 (Rail asm)

Replaced soap dispenser and is working

Replaced heating element and is working

Installed new light bracket and all test ok.