We serviced a
MAYTAG WASHER
Model MVW5035MW1
Near Trinidad, Colorado 81082
James
Job Details: 12/01/2023
"found actuator not moving enough causing noise while agitating. installed preordered cam, actuator and belt. cap not needed. no water hookups on site so could only test without water. all ops test good"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Los Lunas, New Mexico 87031
Larry
Job Details: 12/01/2023
Installed sump and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model JFC2290VPY5
Near Albuquerque, New Mexico 87122
Jason
Job Details: 12/01/2023
Installed ice maker unit checks ok Auth code:44HX9P$206.10
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Albuquerque, New Mexico 87110
Jason
Job Details: 12/01/2023
installed parts unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Rio Rancho, New Mexico 87144
Larry
Job Details: 12/01/2023
Installed ignitor and testd good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Rio Rancho, New Mexico 87144
Larry
Job Details: 12/01/2023
CX complaint - Not draining - Inspected unit and found the drain pump failed - Installed pre-id part and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ01
Near Rio Rancho, New Mexico 87144
Larry
Job Details: 12/01/2023
CX cancelled call - They dont want to pay
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Rio Rancho, New Mexico 87144
Larry
Job Details: 12/01/2023
Installed door and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Rio Rancho, New Mexico 87124
Larry
Job Details: 12/01/2023
CX conmplaint - Not washing dishes - Inspected unit and found the wash motor windings open and the control not sending power to motor - Replaced both and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Albuquerque, New Mexico 87110
Jason
Job Details: 12/01/2023
installed compressor unit checks ok
We serviced a
JENN-AIR MICROWAVE
Model JMV8208CS3
Near Albuquerque, New Mexico 87108
Jason
Job Details: 12/01/2023
installed innerlock kit unit checks okCK AUTHO# U49C4K $206.10
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Rio Rancho, New Mexico 87124
Larry
Job Details: 12/01/2023
CX cancelled call - They dont want to pay
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Albuquerque, New Mexico 87121
Larry
Job Details: 12/01/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Trinidad, Colorado 81082
James
Job Details: 12/01/2023
found loose wire at moisture sensor causing unit to stop abruptly. secured and tested element and other functions. all ckok. did find slight restriction on vent system. advised cust to have licensed vent cleaning service out to address
We serviced a
BOSCH DISHWASHER
Model SHPM65Z55N/20
Near Walsenburg, Colorado 81089
James
Job Details: 12/01/2023
found ui clips to facia disconnected causing buttons to sink into cntl. secured ui to fasteners and tested all ops test good.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS576FIDB02
Near Colorado Springs, Colorado 80927
Aaron
Job Details: 12/01/2023
"Ice maker is unable to find home position, motor clicking with attempts to proceed, cleaned condenser and advised customer of wires stretching at bottom of freezer door. Needs ice maker assembly . Approved onsite. Removed and replaced ice maker assembly, tested through harvest and fill cycles in diagnostics, working well now.Ice maker assembly w10873791 $133.66Tax $10.96Supplies $14.50Hc $149.95Labor $179.95Total job $489.02Approved onsiteNo return on parts Auth total job $489.02 #KYA9Y3"
We serviced a
THERMADOR RANGE
Model PRD486WDGU/05
Near Silverthorne, Colorado 80498
Erik
Job Details: 12/01/2023
install inner door JOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC5
Near Colorado Springs, Colorado 80924
Aaron
Job Details: 12/01/2023
"Removed and replaced lower harness, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ3
Near Peyton, Colorado 80831
Aaron
Job Details: 12/01/2023
"Tested steam clean feature, working and heating well, time needed at end of cleaning needed to safely wipe debris in the unit, tested oven at 350f for 30 minutes, heating well and temperatures are good, external body of unit is at 122f left and 101f right, discussed with techline, paper test for door gasket, working well. Advised customer of 5 star survey. SR7737926275"
We serviced a
JENN-AIR WALLOVEN
Model JMW3430DS03
Near Grand Junction, Colorado 81505
James R
Job Details: 12/01/2023
Customer signed waivers. Replaced console went thru setup procedure. Test operation it is working as should. Customer paid $169.95 auth code 394JFN
We serviced a
JENN-AIR RANGE
Model JGRP748HL05
Near Colorado Springs, Colorado 80921
Jerimiah
Job Details: 12/01/2023
"Griddle cover is starting to chip, called techline to verify, this is considered cosmetic and will it be covered. Took pics. Apparently Cust had Cust service authorize griddle top replacement, techline says no. Small oven is -25? off, large oven having ignition issues. Techline tried to step thru to diagnostic mode, could not locate which breaker unit is on, but is on shared gfci breaker. Unable to get into diag to check unit further. Cust will have to contact builder for assistance. Unit needs further help."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT970SAKZ2
Near Larkspur, Colorado 80118
Glenn
Job Details: 12/01/2023
"Install New Sump Assy, All OPS Test: OK. No Leaks, Install Leak detector for safety."
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ2
Near Peyton, Colorado 80831
Aaron
Job Details: 12/01/2023
"Spray arm melted, removed and replaced, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF220NCTASR/AA
Near Pueblo, Colorado 81005
Brandon
Job Details: 12/01/2023
"Cx said noise is intermittent every other day, checked all components all checks ok could not verify noise, recommend cx record audio and video of noise"
We serviced a
SAMSUNG DOUBLE WALL OVEN
Model OUHPOFSHG
Near Colorado Springs, Colorado 80921
Kris
Job Details: 12/01/2023
installed tco ran test op all ok at this time.
We serviced a
SAMSUNG REFRIGERATOR
Model RF22A4421SR
Near Colorado Springs, Colorado 80911
Mathew
Job Details: 12/01/2023
Found water line was loose. Tightened and test op with 2 gallons of water. No leaks.
We serviced a
SUB ZERO WINE COOLER
Model n/a
Near Colorado Springs, Colorado 80906
Ralph
Job Details: 12/01/2023
"previuos homeowner spilled some teriyaki sauce, cust cleaned up so only charging the sc"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSG/AA
Near Pueblo, Colorado 81004
Brandon
Job Details: 12/01/2023
"Need to replace wire harness in deli drawer rail slide, Svf paid $129.95 Auth# 93UJ49,Da96-00640a $257.64, Labor $189.95, Svf $129.95, Mps $14 50, Tax $21.13"
We serviced a
GENERAL ELECTRIC DISHWASHER
Model ZDT925SPN3SS
Near Colorado Springs, Colorado 80904
Roman
Job Details: 12/01/2023
"Pulled the dw out and installed new drain pump and filter, ran it to check for leaks and make sure dw is working properly. Installed new filter. Dw is working great. Showed cx how to pull the filter out and clean it."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Monument, Colorado 80132
Glenn
Job Details: 12/01/2023
"Install New Sump & Motor Assy, All OPS Test:OK , No Leaks, Installed Leak Detector for safety."
We serviced a
BOSCH REFRIGERATOR
Model B36FD50SNB/02
Near Pueblo, Colorado 81004
Kris
Job Details: 12/01/2023
installed all parts sent 10014425 10005716 10014425
We serviced a
WHIRLPOOL WASHER
Model WTW8800YW0
Near Colorado Springs, Colorado 80921
Glenn
Job Details: 12/01/2023
"making strange noises, Bad Shaft and Basket parts. TUB ASM, HTR - SHAFT & B - W10381077 $416.16 , Basket Assy - W10549509 $670.415 , Also needs new suspension. Parts cost more than new washer, Declined Estimate, Paid SC Fee of $129.95 Via Check #3279 , Autho# H9V93L"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSR/AA
Near Colorado Springs, Colorado 80924
Mathew
Job Details: 12/01/2023
Completed icemaker service bulletin. Test op all okay.
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Pueblo, Colorado 81006
Brandon
Job Details: 12/01/2023
Replaced main board and control panel and tested op all ok
We serviced a
BOSCH DISHWASHER
Model SHPM78Z54N/01
Near Colorado Springs, Colorado 80904
Ralph
Job Details: 12/01/2023
installed parts and unit checked okay
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBW01
Near Colorado Springs, Colorado 80904
Ralph
Job Details: 12/01/2023
REPLACED JAZ BOARD
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Colorado Springs, Colorado 80904
Carlos
Job Details: 12/01/2023
Installed washer doors are leveled pics in quick pics.
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Grand Junction, Colorado 81504
James R
Job Details: 12/01/2023
Put into diagnostics no error codes. Found some coins between agitator and basket removed. Did a service test. In spin empty there is very little vibration. Is fine. Put a load of towels in unit and adjust water level fill. Showed customer. Believe issue is that not enough water on loads causing out of balance so loads cant circulate. It is normal for unit to move side to side and shake some until picks up speed to spin. If gets out of balance need to balance load. Large items are more likely to create out of balanced loads. Drain tube will also sake due to the basket movement. Put foam around tubing and Adjusted rear pane per TSP W11695259Can cause a thumping noise. Unit is operating as should. Signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Colorado Springs, Colorado 80918
Glenn
Job Details: 12/01/2023
"Bad Sump & Motor Assy, Install New Sump & Motor Assy, All OPS Test:OK, No Leaks, Installed Leak detector for safety."
We serviced a
WHIRLPOOL DISHWASHER
Model WDPA70SAMZ
Near Colorado Springs, Colorado 80907
Carlos
Job Details: 12/01/2023
Water supply line to water valve is leaking collecting water in floats switch tray triggering F8E4 code. Cx needs to contact installers to replace line.
We serviced a
JENN-AIR WALLOVEN
Model JMW3430IM02
Near Colorado Springs, Colorado 80907
Carlos
Job Details: 12/01/2023
Installed console ran test op all ok
We serviced a
JENN-AIR MICROWAVE DRAWER
Model JMW8530DAS
Near Peyton, Colorado 80831
Aaron
Job Details: 12/01/2023
"Built in breaker tripped while using self clean feature, removed unit and reset breaker, tested unit and working well now. Advised customer of self clean. Auth $149.95 79.95 oven dolly = $229.90#J4T9CJ and #4TA3M4"
We serviced a
SAMSUNG REFRIGERATOR BOT
Model RF4267HABPI
Near Monument, Colorado 80132
Mathew
Job Details: 12/01/2023
"Found unit in sabbath mode, turned off sabbath mode and fridge is working as expected. Paid svf 129.95. $129.95 CC Auth# 9V394F"
We serviced a
WHIRLPOOL RANGE
Model WFG775H0HZ5
Near Colorado Springs, Colorado 80923
Jerimiah
Job Details: 12/01/2023
They igniter was not consistently igniting fuel. Adjusted shutter for proper air. Fuel mixture. Installed replacement parts. Unit check OK. Disclosed survey to cust fcc 5star.
We serviced a
SAMSUNG DRYER
Model DVE50A8600V/A3
Near Pueblo, Colorado 81001
Brandon
Job Details: 12/01/2023
Replaced PCB and tested op all checks ok
We serviced a
KITCHENAID RANGE
Model KSIB900ESS1
Near Colorado Springs, Colorado 80906
Roman
Job Details: 12/01/2023
"Turned the oven on and it will not get warm, pulled the oven out and a connector on the bake element shorted out. Element is good. Cut back some of the wire and spliced in a new connector. Tested the oven and its getting to temp. Range working great. Sc $129.95Labor $169.95Total cost $299.90Pad S+L"
We serviced a
GE DRYER
Model GTX52EASP0WB
Near Colorado Springs, Colorado 80909
David
Job Details: 12/01/2023
Checked dryer Timer badPicked up timer and installed Tested and timer is advancing
We serviced a
SPEEDQUEEN DRYER
Model ADEE9RYS177TW01
Near Colorado Springs, Colorado 80920
David
Job Details: 12/01/2023
Thermal fuse open Replaced thermal fuse and limit switch Vent is short and clearTested and heating good
We serviced a
WHIRLPOOL DRYER
Model WED7500GC0
Near Colorado Springs, Colorado 80909
David
Job Details: 12/01/2023
Checked dryer Heater burned-out Replaced heater and thermal cut-off kit Tested and is working good
We serviced a
KITCHENAID DISHWASHER
Model KDFE104DSS5
Near Colorado Springs, Colorado 80906
Roman
Job Details: 12/01/2023
"Ran the dishwasher and its fills and sprays, drains out okay. Removed the control board and panel and looked for visible damage. Both look okay. Ran a diagnostic mode on it and it did not come up with any error codes and ran through it okay. If issue persist recommend replacing the main cpuCpu #W11305293 $271.00Tax $22.22Part total $293.22MPs $14.50Labor $189.95Sc $89.95Total cost $487.62Paid sc $89.95 $389.95 CC Auth# UJ44R3"
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5100SRAA
Near Pueblo, Colorado 81001
Brandon
Job Details: 12/01/2023
"No cool all room found a leak at steel to steel connection, repaired, vacuumed for 10 minutes vacuum held for 10 minutes, charged unit, compressor is removing heat, cx will monitor"
We serviced a
GE REFRIGERATOR BO
Model GNE27JYMWFS
Near Colorado Springs, Colorado 80916
Roman
Job Details: 12/01/2023
"Checked that all fans are running and compressor all okay. Took the freezer section apart and there is no frost on the evaporator, has frost on the upper right side indicating a system leak. Recommend replacing the evaporator. Evaporator #WR85X40009 $138.64Tax $11.37Parts total $150.01MPs 14.50Labor $795.95Sc $129.95Total cost $1090.41"
We serviced a
FRIGIDAIRE RANGE
Model FCRE305LAFJ
Near Colorado Springs, Colorado 80915
Jerimiah
Job Details: 12/01/2023
"Installed replacement controller, Cust will keep track of unit."
We serviced a
GE RANGE
Model PS960SL5SS
Near Silverthorne, Colorado 80498
Erik
Job Details: 12/01/2023
CX was worried after total unit burn-off period where both cavitys were set at 400* and all top burners were active. high heat is to be expected during inital burn-off - TESTED: NO EXESIVE HEAT PRESENTJOB COMPLETE
We serviced a
SAMSUNG WASHER
Model WF45M5500AW/A5
Near Colorado Springs, Colorado 80923
Mathew
Job Details: 12/01/2023
"Replaced diaphragm, test op all okay. Collected labor $179.99. $179.95 CC Auth# LL4LUU"
We serviced a
SPEEDQUEEN DRYER
Model ADE6HRYS178TW01
Near Colorado Springs, Colorado 80906
David
Job Details: 12/01/2023
Checked dryer Reattached wire at thermal fuse Good heat and drying
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Colorado Springs, Colorado 80927
Mathew
Job Details: 12/01/2023
"Replaced ACU. Test op, all okay."
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Winter Park, Colorado 80446
Erik
Job Details: 11/30/2023
install motor kitJOB COMPLETE
We serviced a
GE DRYER
Model GTD42EASJ2WW
Near Granby, Colorado 80446
Erik
Job Details: 11/30/2023
installed parts on site/ test: GOODJOB COMPLETE
We serviced a
MONOGRAM DISHWASHER
Model ZDT985SPN8SS
Near Grand Lake, Colorado 80447
Erik
Job Details: 11/30/2023
install/test: connect to smartHQ service:NO ERROR CODES NO ALERTSJOB COMPLETE
We serviced a
WHIRLPOOL DRYER
Model WED8127LW1
Near Albuquerque, New Mexico 87121
Jason
Job Details: 11/30/2023
checked unit found loose wire connection to control re seated plug unit checks ok
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Albuquerque, New Mexico 87121
Jason
Job Details: 11/30/2023
installed part and re leveled machine. unit opperation checks ok
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC0
Near Albuquerque, New Mexico 87120
Jason
Job Details: 11/30/2023
checked unit opperation. unit checks ok suspect items are getting bunched up
We serviced a
WHIRLPOOL WASHER
Model WFW5605MW0
Near Florissant, Colorado 80816
Mathew
Job Details: 11/30/2023
"Replaced case and dampers, test op all okay."
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW
Near Florissant, Colorado 80816
Mathew
Job Details: 11/30/2023
"Replaced both boards, test op all okay."
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS2
Near Florissant, Colorado 80816
Mathew
Job Details: 11/30/2023
"Replaced control, unit now responding. Adjusted flames on cooktop to Cx satisfaction. Called tech line to doc. Checked out okay. Sr# 7737916331."
We serviced a
WHIRLPOOL DRYER
Model GEW9250PL1
Near Colorado Springs, Colorado 80906
Roman
Job Details: 11/30/2023
Deep cleaned the dryer and installed all new support wheels idler pulley and belt. Installed new heating element and tested the dryer. Dryer heating up and working great. Paid check #3290$209.95 CK Auth# LVCJ99
We serviced a
ASKO DISHWASHER
Model dbl675ixxls.U
Near Peyton, Colorado 80831
Kris
Job Details: 11/30/2023
installed light ran test op all ok unit is working to spec at this time.
We serviced a
WHIRLPOOL REFRIGERATOR BOT
Model WRF560SEHZ00
Near Colorado Springs, Colorado 80915
Carlos
Job Details: 11/30/2023
"Installed mullion, all ok door closes ok. Cx paid labor $189.95 CC Auth# P999PJ"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKB1
Near Colorado Springs, Colorado 80909
Carlos
Job Details: 11/30/2023
"Installed spray arm and manifold, all ok cx will observe"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo, Colorado 81003
David
Job Details: 11/30/2023
"Splines in agitator stripped out Replaced agitator Ran diagnostics had a F7E6 code, cleared, ran automatic test. All ran good. Checked error codes again and none."
We serviced a
WOLF DOUBLE WALL OVEN
Model DO305OPMSP
Near Florissant, Colorado 80816
Ralph
Job Details: 11/30/2023
installed parts and unit checked okay
We serviced a
GENERAL ELECTRIC WASHER-DRYER COM
Model PFQ97HSPV0DS
Near Pueblo, Colorado 81007
David
Job Details: 11/30/2023
Checked washer Water dumping onto the clothes from fill tube when the door is opened at end of the cycle.Called tech line number 11643344Possibly opening door too fast causing suction on p trap of fill tube.Tech line suggested opening door slower
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Cañon City, Colorado 81212
James
Job Details: 11/30/2023
"installed ordered parts ran system calibration, tested ops all ckok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Cañon City, Colorado 81212
James
Job Details: 11/30/2023
installed ordered parts all ops test good.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP730HAMZ0
Near Albuquerque, New Mexico 87120
Larry
Job Details: 11/30/2023
Installed sump and tested good - Unit is good to go
We serviced a
KITCHENAID MICROWAVE
Model KMHS120ESS
Near Divide, Colorado 80814
Ralph
Job Details: 11/30/2023
installed listed parts and unit checked okay
We serviced a
KITCHENAID COOKTOP
Model KCGS556ESS02
Near Albuquerque, New Mexico 87120
Larry
Job Details: 11/30/2023
Installed ingnitors and module and tested good - Unit is good to go
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC703HPS04
Near Albuquerque, New Mexico 87120
Larry
Job Details: 11/30/2023
Installed parts listed and tested goode - Unit is good to go
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Albuquerque, New Mexico 87120
Larry
Job Details: 11/30/2023
CX complaint - F8E4 - Inspected unit and found the tub gasket leaking - REplaced with pre-id parts and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model MGD5500FW0
Near Albuquerque, New Mexico 87114
Jason
Job Details: 11/30/2023
checked unit found unit needs a repair kitSC$151.85MISC$17.50LABOR$216.95REPAIR KIT#4392067$75.90TX$6.45TOTAL$468.65CX DOES NOT WANT TO REPAIRAuth code:9VUH49$151.85
We serviced a
DACOR DOWNDRAFT VENT
Model RV36W
Near Elbert, Colorado 80106
Kris
Job Details: 11/30/2023
installed board and motor ran test op all ok at this time.
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW2
Near Tabernash, Colorado 80478
Antonio
Job Details: 11/30/2023
Found cx ran unbalanced load unit tested fine did mention if wanted could replace shocks but not needed at this time $149.95 CC Auth# J4FX39
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPA
Near Tabernash, Colorado 80478
Antonio
Job Details: 11/30/2023
Installed new fan unit tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ05
Near Granby, Colorado 80446
Antonio
Job Details: 11/30/2023
Installed new thermistor until tested good
We serviced a
WHIRLPOOL DRYER
Model WED8620HC2
Near Granby, Colorado 80446
Antonio
Job Details: 11/30/2023
"Installed new motor, wheel, and housing unit tested good"
We serviced a
JENNAIR REFRIGERATOR
Model JBSS48E22L00
Near Colorado Springs, Colorado 80906
Roman
Job Details: 11/30/2023
"Fridge has a fishy smell coming from the lower drawers in ff section, filter was not installed but I installed it. Fridge is completely empty and has been cleaned. Has 3 baking soda packs inside. Called tech support to see if they had any other ideas. Going to wait and see if the filter takes care of the odors."
We serviced a
AMANA DRYER
Model NED4655EW1
Near Pueblo, Colorado 81005
David
Job Details: 11/30/2023
Installed maintenance kit and front clips Tested and running good
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS03
Near Grand Lake, Colorado 80447
Antonio
Job Details: 11/30/2023
Found heat exchanger vibrating level unit unit tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, Colorado 80922
Aaron
Job Details: 11/30/2023
"Water connection not fully engaged, corrected tested, working well now. RC at 35.8f at time of inspection, advised customer of usage and coil pack. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL RANGE
Model MER8800FZ1
Near Monument, Colorado 80132
Glenn
Job Details: 11/30/2023
"Install New Bake Element, All OPS Test:OK, Paid remaining Balance for Labor 209.95 + MPS $14.50 = $224.45 + Tip $22.45 = $246.90"
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Albuquerque, New Mexico 87107
Larry
Job Details: 11/30/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL RANGE
Model KGSK901SSS00
Near Carbondale, Colorado 81623
James R
Job Details: 11/30/2023
Customer indicates that oven will start but then doesnt heat up properly. Also hears it spark several times and not light then smells gas. Gas shuts off. Set oven to 400 degrees put digital thermometer in center of oven and let cycle several times To see if it lights good and maintains temperature. At times can hear it spark several times before it lights. Then it tried to light again sparked several times but did not light tried again and lit. Oven temp did drop some but did go back up to temp. Gave estimate to customer to repair. $538.21 plus labor $149.95 total $688.16 He will not repair at this tome. Paid service call $149.95 auth code. 4EN93E Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Colorado Springs, Colorado 80919
Brandon
Job Details: 11/30/2023
"Replaced ice maker, cleared ice, reset cycled ok, all checks ok"
We serviced a
SUBZERO REFRIGERATOR
Model 249RPLH
Near Larkspur, Colorado 80118
Jessie
Job Details: 11/30/2023
Replaced bad control. Test op. Evap plate is freezing up. All ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA 03
Near Colorado Springs, Colorado 80919
Brandon
Job Details: 11/30/2023
"Replaced evap cover, no errors, fans ok, temps good, all checks ok"
We serviced a
KITCHENAID WALLOVEN
Model KOCE507EBS22
Near Monument, Colorado 80132
Glenn
Job Details: 11/30/2023
Install New Support for Ceiling Element. All OPS Test:OK
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Monument, Colorado 80132
Glenn
Job Details: 11/30/2023
"Temps Good, Verified No broken door harness wires, Reseat connections to Ice Maker. IM Sensor Test > Pass, IM Cycle Test>Pass , IM Fill Test > Pass, All OPS Test:OK at this time."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Monument, Colorado 80132
Glenn
Job Details: 11/30/2023
"Install New Chute, Coupler & Container. All OPS Test:OK"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Colorado Springs, Colorado 80920
Glenn
Job Details: 11/30/2023
Install New Control & Evap Thermistor.All OPS Test:OK