Service History 37 - D3 Appliance

We serviced a

WHIRLPOOL RANGE

Model WOS51EC0HS20

Near Albuquerque, NM 87120

Larry

Job Details: 04/04/2025

CX complaint - 'Power Loss' on display - Inspected unit and found F6E6 and F6E4 comms errors - Unit needs UI and control - CX does not want to bear the cost of repair - Collected SC-auth-43E4M9 - Estimate in QP

We serviced a

WOLF RANGE

Model DF60650DG/S/P

Near Colorado Springs, CO 80921

Jerimiah

Job Details: 04/04/2025

"Gave probe to cust, Cust will test unit tonight to see if it works, complaint is still when using probe system shuts down 2.2.0 is current sw but was unable to find sw ver in oven screens. Techline suggested if problem is with just one oven vs both ovens, solution might be to replace that respective relay board. Must verify if one oven or both. Cust will keep track of functionality."

We serviced a

COVE DISHWASHER

Model DW2450WS

Near Colorado Springs, CO 80906

Ralph

Job Details: 04/04/2025

REPLACED LISTED PART AND SAW NO SIGNS OF LEAKING CUST TO MONITOR

We serviced a

THOR REFRIGERATOR

Model TRF3601FD

Near Colorado Springs, CO 80908

Ryan

Job Details: 04/04/2025

Adjusted door closer/mullion and door now closing properly.Operating noise is normal. RKAuth T94LWL

We serviced a

MAYTAG WASHER

Model MVWB835DW4

Near Rio Rancho, NM 87124

Antonio

Job Details: 04/04/2025

"cx complanit - no operation - replaced gearcase,panel-cntl,slider-assembly and clutch-assembly - unit is working properly - survey mentioned"

We serviced a

MAYTAG WASHER

Model MVW7232HW1

Near Albuquerque, NM 87105

Larry

Job Details: 04/04/2025

Installed parts listed tested good - unit is good to go - Survey mentioned

We serviced a

KITCHENAID DISHWASHER

Model KDTE404DSS0

Near Albuquerque, NM 87111

Jason

Job Details: 04/04/2025

Installed rails ran quick cycle unit opperation checks ok. spoke to cx about review.

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW2

Near Albuquerque, NM 87105

Larry

Job Details: 04/04/2025

CX complaint - Water leaking - Inspected unit and found that when the washer drains the stand pipe backs up and floods - Advised cx to call a plumber - Washer is operating as designed

We serviced a

MAYTAG WASHER

Model MVWB835DW4

Near Rio Rancho, NM 87144

Antonio

Job Details: 04/04/2025

"cx complanit - not agitating - replaced slider assembly,clutch assembly and gearcase unit is working properly - survey mention"

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW1

Near Phoenix, OR 97535

Jeff

Job Details: 04/04/2025

Installed valve tested working as should

We serviced a

MAYTAG WASHER

Model MVW7230HW1

Near Madras, OR 97741

Richard

Job Details: 04/04/2025

Installed parts listed cycle tested unit on Quick wash all tested fine at this timeof repair

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FBS05

Near Medford, OR 97504

Jeff

Job Details: 04/04/2025

"Installed auger motor, bin and plate. Tested auger is working"

We serviced a

WHIRLPOOL DRYER

Model WED5100HC3

Near Albuquerque, NM 87112

Jason

Job Details: 04/04/2025

Checked unit found element open. installed element and cutoff. ran timed dry cycle unit opperation checks ok. spoke to cx about review

We serviced a

MAYTAG DRYER

Model MED7230HW3

Near Rio Rancho, NM 87124

Antonio

Job Details: 04/04/2025

"panel- cntrl was cracked out of box,had to reorderpart,installed panei cntrl - unit is worling properly - survey mention"

We serviced a

MAYTAG DRYER

Model MED6500MBK0

Near Albuquerque, NM 87114

Antonio

Job Details: 04/04/2025

"cx complanit - drum not turning - replaced repair kit,fuse andmotor drive assembly - unit is working properly - survey mentioned"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM9

Near Colorado Springs, CO 80925

Carlos

Job Details: 04/04/2025

Installed sump assembly ran test all ok left leak strip

We serviced a

AMANA DISHWASHER

Model ADB2500AWS

Near Colorado Springs, CO 80919

Dvante

Job Details: 04/04/2025

Replaced accumulator. The screen was intact. No tears and damages. No leaks under the unit. Unit is operating as designed.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ18

Near Grand Junction, CO 81504

Josh

Job Details: 04/04/2025

"Customer signed disclaimer. Verified MN SN.Customer states that unit is not producing enough ice. Tech found unit approximately 1/3 full of well formed cubes, as well as the ice-maker mold full. Tech forced harvest and observed productive fill. Technician contacted manufacturer, performed tests, and confirmed unit is operating properly to the design specifications. Manufacturer states that this model takes 48-72 hours to fill ice reservoir, and all components are functioning properly."

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS3

Near Grand Junction, CO 81507

Sean

Job Details: 04/04/2025

Checked unit MN SN POP Opened package and checked content good Customer signed disclaimer.Opened the unit and removed the inside panel on the door. Removed the console assembly and wire harness. Installed the new console assembly and wire harness. Removed the door vent and installed the new one into the door. Reassembled the unit. Tested all buttons are working and ran unit on drain cycle.Tested unit good.Please fill out a tech surveyThank you.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ11

Near Grand Junction, CO 81504

Josh

Job Details: 04/04/2025

"Customer signed disclaimer, verified MN SN. Tech verified correct retrofit assembly kit was received and is intact. Installed replacement components/kit. Forced harvest/fill cycle, unit is functioning properly within manufacturer specifications."

We serviced a

MAYTAG WASHER

Model MVW4505MW1

Near Grand Junction, CO 81504

Josh

Job Details: 04/04/2025

Tech installed replacement capacitor and confirmed operation of unit.

We serviced a

WHIRLPOOL DRYER

Model WED560LHW2

Near Colorado Springs, CO 80915

Carlos

Job Details: 04/04/2025

Installed wheel all ok

We serviced a

WHIRLPOOL VENT HOOD

Model UXT4130ADS

Near Colorado Springs, CO 80903

Carlos

Job Details: 04/04/2025

"Installed power cord kit, runs all ok"

We serviced a

WHIRLPOOL DRYER

Model WED560LHW2

Near Colorado Springs, CO 80903

Carlos

Job Details: 04/04/2025

"The idler pulley was replaced on the dryer, and following the installation, the operational noise previously reported is no longer present. The unit now runs smoothly and quietly, confirming that the issue has been successfully resolved."

We serviced a

WHIRLPOOL DRYER

Model WED6720RR0

Near Peyton, CO 80831

Aaron

Job Details: 04/04/2025

"Inspected unit, found steam spray nozzle not properly secure, corrected and tested operation, working well now, door gasket secure, recommend using multiple items to collect water when using the steam feature. Advised customer of situation and survey."

We serviced a

MAYTAG DRYER

Model MED6230HW3

Near Colorado Springs, CO 80920

Dvante

Job Details: 04/04/2025

Replaced air duct. No damages or sharpness to the air duct. Sheet not catching on to it. Unit is operating as designed.

We serviced a

WHIRLPOOL RANGE

Model WFC315S0JS3

Near Colorado Springs, CO 80908

Aaron

Job Details: 04/04/2025

"Bake element resistance is low, removed and replaced, tested unit at 350f, averaging 362f, calibrated accordingly. Advised customer of situation and survey."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706EBS05

Near Bend, OR 97702

Levi

Job Details: 04/04/2025

Customer called us back because she was shipped out door seals prior to previous visit and they still have the door seals. The right hand refrigerator door seal is slightly torn but it cannot be replaced because the seals are formed in place and would need a new door. Unit is now out of warranty and would be very expensive for the customer.

We serviced a

KITCHENAID RANGE

Model KSGG700ESS7

Near Colorado Springs, CO 80927

Aaron

Job Details: 04/04/2025

"Inspected unit, contacted techline once more, sent pictures of flame spreader as requested, closed gas valve air door as requested, documented history of repairs, sending off to research, whirlpool will cobtact the customer with conclusion. Advised customer of situation and survey. SR7741117494"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Monument, CO 80132

Dvante

Job Details: 04/04/2025

Replaced reservoir. Tested dispenser and water isnt leaking in the back of the unit. Unit is operating as designed.

We serviced a

WHIRLPOOL DRYER

Model WED500CMW0

Near Colorado Springs, CO 80924

Aaron

Job Details: 04/04/2025

"Top, right side cabinet, and back panels are damaged from dents, removed and replaced components, no scratches or dents, verified by customer, unit is working and heating well now. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT531HAPM0

Near Colorado Springs, CO 80915

Carlos

Job Details: 04/04/2025

Found debris in drain removed runs all ok

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW1

Near Sisters, OR 97759

Richard

Job Details: 04/04/2025

Tested unit unable to duplicate issue unit working as designed at this time if customer has isxue later they will call back for service

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS12

Near Medford, OR 97504

Jeff

Job Details: 04/04/2025

Right now everything is functioning as normal tested all good temps lights work customer to monitor. Think it just glitched.

We serviced a

WHIRLPOOL DRYER

Model WED5010LW1

Near Grants Pass, OR 97527

Thomas

Job Details: 04/04/2025

Replaced harness and power cord. Ran tested okay with customer present. Advised customer of survey

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRFC2036RW00

Near Grants Pass, OR 97527

Thomas

Job Details: 04/04/2025

Used sealant per Whirlpool TS recommendation. Customer will monitor. Advised customer of survey

We serviced a

MAYTAG WASHER

Model MHW8630HC4

Near Jacksonville, OR 97530

Thomas

Job Details: 04/04/2025

Replaced all parts listed. Ran tested okay no leaks. Customer will test later. Advised customer of survey

We serviced a

MAYTAG WASHER

Model MHW8630HC4

Near Bend, OR 97701

Levi

Job Details: 04/04/2025

Found soap injection was a bit clogged due to detergent being too concentrated. Cleaned injector and tested detergent pump with just water and pump worked good. Recommended less concentrated soap or diluting the detergent to about 2 to 1 and try that. Did not detect any smells

We serviced a

LG REFRIGERATOR

Model LRFXS3106S/00

Near Colorado Springs, CO 80924

Dvante

Job Details: 04/02/2025

Replaced the evaporator cover with fan motors along with the main pcb. Checked for cool air and its going inside the ice room area. Unit is operating as designed.

We serviced a

LG MICROWAVE

Model MVEL2033D.BBDELGA

Near Colorado Springs, CO 80908

Ryan

Job Details: 04/02/2025

Installed new board and touchpad. Unit now working properly. RK

We serviced a

MIELE WASHER

Model WWD660

Near Aspen, CO 81611

Sean

Job Details: 04/02/2025

Checked unit MN SN POP Customer signed disclaimer.Customer said that the color detergent was not dispensing.Put unit into test mode and ran an auto test. Watched the unit dispense detergent. Drained the unit and rinsed out the tub. Ran the unit on calibration cycle. Went into programming mode and set the color detergentDispenser amount from 46 to 50 .Ran a test cycle and watched the water get bubbles in it.Ran a spin and drain cycle and then set unit to run a calibration cycle. Unit has no errors tested the unit good.Please fill out a technician survey.Thank you.

We serviced a

WHIRLPOOL WASHER

Model CET9000GQ2

Near Colorado Springs, CO 80903

Carlos

Job Details: 04/02/2025

Installed Detergent drawer all ok

We serviced a

SAMSUNG MICROWAVE

Model ME21DG6300SRAA

Near Colorado Springs, CO 80920

Jerimiah

Job Details: 04/02/2025

Installed replacement mag and controller. Oriented blower to recirculate mode due to missing external venting. Unit check ok

We serviced a

SAMSUNG REFRIGERATOR

Model RF23M8570SR/AA

Near Fountain, CO 80817

Mathew

Job Details: 04/02/2025

"Installed new auger, water pitcher and seal, pcb and bin. Test operation all okay. Unit working as expected."

We serviced a

SAMSUNG DRYER

Model DVE52A5500V/A3

Near Colorado Springs, CO 80905

Brandon

Job Details: 04/02/2025

Replaced heater assy and tested operation hass oqc passed recommended vent cleaning

We serviced a

SAMSUNG WASHER

Model WF45T6000AV/A5

Near Colorado Springs, CO 80938

Brandon

Job Details: 04/02/2025

"Loose bolts on damper, tightened and tested operation hass oqc oassed"

We serviced a

SAMSUNG REFRIGERATOR

Model RF27CG5900SRAA

Near Colorado Springs, CO 80903

Mathew

Job Details: 04/02/2025

Instal seal kit. Install new filter case. Test operation all okay.

We serviced a

SAMSUNG REFRIGERATOR

Model RF30BB660012AA

Near Pueblo, CO 81008

Domingo

Job Details: 04/02/2025

Replaced filter assembly and test it and got water to water dispenser

We serviced a

VIKING RANGE

Model VGIC305-4BSS

Near Colorado Springs, CO 80909

Jerimiah

Job Details: 04/02/2025

Installed 2nd igniter. Unit check ok charged labor as quoted $296.95 CC Auth# 3C444F

We serviced a

BOSCH RANGE

Model HDI8054U/06

Near Vail, CO 81657

Erik

Job Details: 04/02/2025

CX cancel call - issue resolved itself

We serviced a

WOLF RANGE

Model DF48450CG/S/P

Near Monument, CO 80132

Ryan

Job Details: 04/02/2025

Installed broiler rework kit. Tested operation OK. RK

We serviced a

WOLF RANGE

Model DF36450G/S/P

Near Monument, CO 80132

Ryan

Job Details: 04/02/2025

Installed rework kit but griddle burner still not working due to faulty ignition board. will need to replace board.Part $293Tax $24.02Material $14.50Labor $209.95Total $541.47Customer will contact if she wants unit repaired.RK

We serviced a

SUB ZERO REFRIGERATOR

Model CL4250UFDID/S/T

Near Monument, CO 80132

Ryan

Job Details: 04/02/2025

Replaced damaged freezer drawer panel. RK

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDEM01

Near Albuquerque, NM 87109

Jason

Job Details: 04/02/2025

Installed led modules all modules check ok. spoke to cx about review

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ4

Near Los Lunas, NM 87031

Larry

Job Details: 04/02/2025

CX complaint - No water coming in - Inspected unit and found the valve and wash motor failed - Replaced qith Pre-ID parts and tested good - Unit si good to go - Survey mentioned

We serviced a

MAYTAG REFRIGERATOR

Model MBF1958DEM00

Near Aspen, CO 81611

Josh

Job Details: 04/02/2025

"Customer signed disclaimer. Verified MN, SN, POP. Confirmed correct part received in good condition. Tech installed replacement evaporator fan, confirmed proper operation/direction, and reassembled unit. Unit is functioning properly within manufacturer specifications.Thank you for allowing us to service your refrigerator today! Please take a moment to let us know how weve done by completing our technician satisfaction survey. Please call us with any questions or all your appliance needs!"

We serviced a

WHIRLPOOL M/W OTR

Model WML75011HZ10

Near Albuquerque, NM 87114

Antonio

Job Details: 04/02/2025

"cx complanit - door not latching - replaced board, still not latching,called technical support for assistance had to to loosen the two screws that keeps the latch switch in place,once the screws were loosen the door latched.unit is working properly - survey mentioned"

We serviced a

WHIRLPOOL WALL OVEN

Model WOS51EC0HS02

Near Los Lunas, NM 87031

Larry

Job Details: 04/02/2025

Installed UI and tested good - Unit is good to go - Survey mentioned

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ11

Near Albuquerque, NM 87123

Jason

Job Details: 04/02/2025

INstalled tube and sealed with a dab of food grad silicone. re-testred ice maker fill unit opperation checks ok. spoke to cx bout review

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX986SIHZ01

Near Albuquerque, NM 87111

Jason

Job Details: 04/02/2025

Installed led modules unit opperation checks ok. spoke to cx about review

We serviced a

AMANA WASHER

Model NTW4519JW2

Near Rio Rancho, NM 87124

Antonio

Job Details: 04/02/2025

"cx complanit - squealing noise - ran unit on rinse/spin and drainl/spin cannot duplicate sound that cx heard - called technical support to have it document,unit is working properly (SR#7741270523) - survey mentioned"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT311FZDM02

Near Belen, NM 87002

Larry

Job Details: 04/02/2025

Installed ice maker and tested good - Unit is good to go - Survey mentioned

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Albuquerque, NM 87105

Larry

Job Details: 04/02/2025

CX complaint - F3E1 wsher not turning off - Inspected unit and found the pressure system failed - Replaced control with pre-id part and tested good - Unit is good to go - Survey mentioned

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Rio Rancho, NM 87144

Antonio

Job Details: 04/02/2025

"cx complanit - unit is not working - replaced pump motor,unit is working properly - survey mentioned"

We serviced a

MAYTAG DRYER

Model MED6200KW1

Near Albuquerque, NM 87111

Jason

Job Details: 04/02/2025

Installed parts ran diagnostic test cycle to check sensor function. sensor function and heating both check ok. unit opperation checks ok. spoke to cx about review

We serviced a

MAYTAG WASHER

Model MAH5500BWQ

Near Colorado Springs, CO 80919

Ryan

Job Details: 04/02/2025

Unit working properly at this time.Previous cycle may have gone off balance.Inst. customer on operation. RKAuth 3LJUM4

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Colorado Springs, CO 80925

Carlos

Job Details: 04/02/2025

"Broken wire at capacitor, repaired. Recommend cx do not overload unit, F7E3 code present ran calibration to rectify issue."

We serviced a

MAYTAG WASHER

Model MVWX655DW2

Near Colorado Springs, CO 80927

Aaron

Job Details: 04/02/2025

"Control is constantly sending power to the drain pump, removed and replaced control, recalibrated and tested unit, working well now. Advised customer of 5 star survey."

We serviced a

MAYTAG WASHER

Model MVW6200KW

Near Colorado Springs, CO 80911

Mathew

Job Details: 04/02/2025

"Replace bezel, control, actuator. Test operation. All okay."

We serviced a

MAYTAG WASHER

Model MVWB865GC0

Near Colorado Springs, CO 80907

Carlos

Job Details: 04/02/2025

Installed glass door runs all ok

We serviced a

WHIRLPOOL DISHWASHER

Model KDTF324PPA00

Near Edwards, CO 81632

Antonio

Job Details: 04/02/2025

Installed new door seal ran a cycle for proper operation and unit tested good Also advised cx of whlp survey

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF536RBS01

Near Eagle, CO 81631

Antonio

Job Details: 04/02/2025

Installed new compressor and couplers turn unit on fridge at 35?and freezer at 0? unit testing good also advised cx of whlp survey

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF536RPS00

Near Glenwood Springs, CO 81601

Sean

Job Details: 04/02/2025

Checked unit MN SN POP Customer signed disclaimer.Looked at the unit found the unit satisfied. Adjusted the temp lower in order to start the unit. Customer then emptied the ice maker.Unit still not making sounds. Left unit open for 5 minutes Until the compressor came on. It is running extra quietly.I can not get the unit to make the sound. Put unit into service mode and ran tests on all components.When I changed the compressor speed it started to vibrate. Pulled the unit out and removed back panel. Checked machine compartment. Found when I'd push on the condenser it would vibrate the bottom of the freezer box. Adjusted the condenser and put some foam between it and the box. Tested vibration is gone Tested the unit good .No more sound. Please fill out a tech servey.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB329DMBW05

Near Colorado Springs, CO 80909

Carlos

Job Details: 04/02/2025

Dropped leveling feet all ok

We serviced a

WHIRLPOOL DRYER

Model WED4950HW0

Near Divide, CO 80814

David

Job Details: 04/02/2025

"Belt broken, installed repair kit. Running good."

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Woodland Park, CO 80863

David

Job Details: 04/02/2025

"Replaced control, ran diagnostics, and a cycle, all good."

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS11

Near Colorado Springs, CO 80908

Aaron

Job Details: 04/02/2025

"Removed and replaced right RC door, no scratches or dents, verified by customer. Advised customer of 5 star survey."

We serviced a

MAYTAG WASHER

Model MVW4505MW2

Near Pueblo, CO 81001

James

Job Details: 04/02/2025

Found loose pressure hose at cntl causing unit I to not register water level. Secured and tested all ops test good

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF577KBS02

Near Colorado Springs, CO 80917

Aaron

Job Details: 04/02/2025

"Removed and replaced reservoir, purged line and no leaks, working well now. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ1

Near Colorado Springs, CO 80909

Carlos

Job Details: 04/02/2025

"Installed Drain pump, left leak strip"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRMF3636RB00

Near Sunriver, OR 97707

Levi

Job Details: 04/02/2025

Found filter went bad.checked all filter connectors and everything checks okay.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHW08

Near Terrebonne, OR 97760

Richard

Job Details: 04/02/2025

Installed new inlet valve cycle tested unit all tested fine at this time no leaks at time of repair

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Bend, OR 97701

Richard

Job Details: 04/02/2025

Tested unit found blown thermal fuse and broken heating element installed parts preshipped to customer cycle tested unit all tested fine at time of repair

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRFC2036RZ00

Near Bend, OR 97701

Levi

Job Details: 04/02/2025

Replace compressor tested good.

We serviced a

WHIRLPOOL RANGE

Model WFE535S0LS3

Near Terrebonne, OR 97760

Richard

Job Details: 04/02/2025

Installed new burner switch and left front burner cycle tested unit all tested fine at time of repair

We serviced a

MAYTAG WASHER

Model MVWP575GW0

Near Colorado Springs, CO 80920

Aaron

Job Details: 04/02/2025

"F7E1 sensor, F7E7 RPM error codes upon arrival, inspected unit, actuator is not changing gears, drive pulley and belt are worn, approved repair onsite, removed and replaced components, tested unit, working well. Drive pulley $77.65Belt $63.63Actuator $131.80Total parts $273.08Tax $22.39Supplies $14.50Hc $139.95Labor $179.95Total job $629.8730 day estimate No return on parts Auth total job $629.87 #KV9WX4"

We serviced a

MAYTAG DRYER

Model MED6500MBK

Near Colorado Springs, CO 80908

Aaron

Job Details: 04/02/2025

"Heating element is shorted out, removed and replaced, placed unit is best position for best airflow, tested unit, working and heating well now. Advised customer of 5 star survey."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706EBS

Near Pueblo, CO 81005

Domingo

Job Details: 04/02/2025

Freezer light wires were broken I repair wires and lights came back on

We serviced a

BOSCH DISHWASHER

Model SHP78CM4N/22

Near Colorado Springs, CO 80920

Ryan

Job Details: 04/02/2025

Cleaned out clogged filter.Ran diagnostic test cycle and everything now checks ok . RK

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ04

Near Colorado Springs, CO 80922

Aaron

Job Details: 04/02/2025

"Thermistor error code for ice maker, removed and replaced, tested unit through harvest and fill cycles, working well now, needs time to cool. Advised customer of 5 star survey."

We serviced a

GE WASHER

Model GFW650SPN4SN

Near Peyton, CO 80831

Charles

Job Details: 04/02/2025

"Ran diagnostics, fill, drain, pressure switch test. Disassembled and inspected interior, no leaks. Ran rinse & spin with load."

We serviced a

SAMSUNG WASHER

Model WA52A5500AC

Near Colorado Springs, CO 80924

Dvante

Job Details: 04/02/2025

"Replaced the main pcb. Tested unit, passed HASS. No error codes. Unit is operating as designed"

We serviced a

WHIRLPOOL WASHER

Model WTW6157PW

Near Colorado Springs, CO 80911

Carlos

Job Details: 04/02/2025

Installed motor and clutch runs all ok Cx

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ0

Near La Pine, OR 97739

Levi

Job Details: 04/02/2025

Replaced sump and motor assembly. Tested. All checks okay and no leaks down at time of service

We serviced a

GE WASHER

Model GFW850SPN0RS

Near Peyton, CO 80831

Charles

Job Details: 04/02/2025

Installed drain pump and main control board. Tested in diagnostics.

We serviced a

KITCHENAID DISHWASHER

Model KDFE104HPS1

Near Colorado Springs, CO 80920

Aaron

Job Details: 04/02/2025

"Lower rack wheel pins missing, wheel falling off, diverter is not allowing water to lower spray arm, called and received approval, removed and replaced components, tested unit, working well now, no leaks, installed litmus strip and advised customer of survey."

We serviced a

BOSCH DISHWASHER

Model SHV78CM3N/26

Near Beaver Creek, CO 81620

Erik

Job Details: 04/02/2025

MOD/ SN DO NOT MATCH* see quick picsdoor panel bent* see quick picsJOB COMPLETE

We serviced a

THERMADOR WALL OVEN

Model ME301YP/03

Near Edwards, CO 81632

Erik

Job Details: 04/02/2025

ACCESS FRONT DOOR - CX NOT ON SITEinstall relay board and cooling fan asm/ test: PASSJOB COMPLETELEFT INSTARUCTION FOR CX TO CONNECT TO WIFI FOR SIFTWARE UPDATES* see quick picsCXNOT AVAILABLE FOR SIGNATURE

We serviced a

THERMADOR REFRIGERATOR

Model T36FT820NS/05

Near Aspen, CO 81611

Sean

Job Details: 04/02/2025

Checked unit MN SN POP Customer signed disclaimer.Raised the legs and pulled the unit out onto my pad. I got behind the unit and listened to it. Tested any sound level with my decibel meter. During start up behind the unit it was at -83 DBRemoved the back cover and examined the compressor and copper found nothing out of place. Applied foam sound reduction tape around the back panel and to the copper and parts of the compressor. Reassembled the unit.Tested the DB level behind the unit upon start up.Unit peaked at -72 DBs. I managed to reduce the overall sound from unit by 11 dbs.Tested the unit good. Please fill out a tech servey

We serviced a

BOSCH RANGE

Model HGIP056UC/09

Near Florissant, CO 80816

Ralph

Job Details: 04/02/2025

"upon arrival found the center burner not igniting correctly, fount the unit was igniting off the inside of the burner base, removed the base and resituated the ignter and now it is working correctly cust to monitor."