We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ4
Near Grand Junction, CO 81501
James R
Job Details: 10/25/2024
Replaced bake burner and igniter. Test operation let heat up to 350 degrees then let cool abit and then restart lit right up is operating as should. Please fill out tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MVW6230RHW0
Near Bend, OR 97701
Levi
Job Details: 10/25/2024
"Replaced shifter and splutch kit, tested good"
We serviced a
SAMSUNG REFRIGERATOR
Model RF217ACBP
Near Colorado Springs, CO 80917
Brandon
Job Details: 10/25/2024
Cancelled
We serviced a
MAYTAG WASHER
Model MVWB835DW3
Near Albuquerque, NM 87114
Larry
Job Details: 10/25/2024
CX Stated he has an extended warranty - Advised him to have a new dispatch made
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC0
Near Peralta, NM 87042
Larry
Job Details: 10/25/2024
CX complaint - F6E3 on display - Inspected unit and found the controls failed - CX doesn't want to bear the caost of repair and will replace - CX paid SC-A99JV4 - Estimate in QP
We serviced a
WHIRLPOOL DRYER
Model WGD8127LC3
Near Dillon, CO 80435
Antonio
Job Details: 10/25/2024
Installed fuse coil and ignitor ran a cycle for proper operation and unit tested good
We serviced a
WHIRLPOOL DRYER
Model WED4616FW0
Near Colorado Springs, CO 80919
Glenn
Job Details: 10/25/2024
"Vacuum lint and rubber shavings from old roller. Install New LS Rear Support Shaft, and 2 New Rear Suppot Rollers. All OPS Test:OK, Vent appears good w/ no restrictions. Paid Labor Balance of $199.95, Autho# 3VVTL4"
We serviced a
JENNAIR REFRIGERATOR
Model JFFCF72DKL06
Near Colorado Springs, CO 80921
Glenn
Job Details: 10/25/2024
"Install New LS Lower Door Hinge & Closer, & Mullion, RS Door Gasket, Adjust Gasket. All OPS Test:OK"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS0
Near Colorado Springs, CO 80921
Glenn
Job Details: 10/25/2024
"Water found in overflow tray. Customer indicated they ran a clean cycle using cleaning pod, which filled the unit with suds. Emptied overflow tray & and ran Diag Test Cycle multiple times. No Leaks found. Install Leak strip detector for safety. Paid SC Fee $129.95 + Tip $19.49 = $149.44 , Autho# 4JTMU9"
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ4
Near Bend, OR 97702
Levi
Job Details: 10/25/2024
Replaced listed parts tested good
We serviced a
KITCHENAID RANGE
Model KSEG700ESS7
Near Grand Junction, CO 81501
Sean
Job Details: 10/25/2024
customer signed disclamerchecked unit unit had error code ran diagnostics error F2 E1 .disconented powerremoved control and installed new control panerestored power. ran diagnostics unit tested good.please fill out the tech servey
We serviced a
GE WASHER
Model GFW550SSN5WW
Near Dillon, CO 80435
Erik
Job Details: 10/25/2024
connect to smart HQ service: ERROR CODE F26 OBO -spin test: PASSApply firmware update/ reverse door swing on washerJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Bend, OR 97702
Levi
Job Details: 10/25/2024
Replace control board tested all checks okay. Finished up with running a recalibration cycle
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Grand Junction, CO 81503
Sean
Job Details: 10/25/2024
customer signed disclamerdrain running continuesly. ran diagnostic found presure sistom fault.F3 E1long fill F8 E1main control F1E1deturmind unit need new control.( W11603810 ) CNTRL-ELEC290.02 for control.customer does not want to repair unit looking to replace.customer paid $149.95 with card.authcode RA33MVtransaction # 1672756pleas fill out a tech servey
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ10
Near Grand Junction, CO 81507
James R
Job Details: 10/25/2024
"Replaced glass shelves,meat pans and pan fronts. Customer will let know if there are any issues. Please fill out tech satisfaction survey. Thank You."
We serviced a
KITCHENAID DOUBLE WALL OVEN
Model KOCE500ESS22
Near Rio Rancho, NM 87144
Joe
Job Details: 10/25/2024
"Cx complaint, mw getting too hot/ not cooking correctly. Replaced inverter and magnetron ordered last visit. Tested unit by heating cup of water for 30 seconds. Unit good to go"
We serviced a
SAMSUNG DRYER
Model DVE50BG8300EA3
Near Colorado Springs, CO 80921
Brandon
Job Details: 10/25/2024
"No errors, unit is working to spec, told cx not use eco mode as it can take longer to dry, tested op all checks ok hass oqc passed"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ2
Near Medford, OR 97504
Austin
Job Details: 10/25/2024
The unit was pulled out. The new insulation was placed. The unit was put back in place and tested. The unit worked. The customer signed all appropriate paperwork.
We serviced a
THERMADOR RANGE
Model PDR364GDZS
Near Colorado Springs, CO 80906
Jerimiah
Job Details: 10/25/2024
"Installed replacement bake element. Repaired wiring, unit check ok. Charged labor as quoted $259.95 CC Auth# 93AYE3."
We serviced a
SAMSUNG WASHER
Model WF50BG8300AEUS
Near Colorado Springs, CO 80921
Brandon
Job Details: 10/25/2024
"Found unit wobbling and unlevel, level unit and tested op all checks ok hass oqc passed"
We serviced a
SAMSUNG RANGE
Model NE58K9560WS/AA
Near Monument, CO 80132
Brandon
Job Details: 10/25/2024
"Oven not heating, getting voltage to board but neither broil or bake getting power, relays are clicking but not power, need main PCB, Svf paid $129.95 Auth# 99CRAH"
We serviced a
SAMSUNG REFRIGERATOR
Model RF26HFENDSR
Near Bend, OR 97702
Levi
Job Details: 10/24/2024
Found EVAP cover needs replaced. Also found drain was clogged
We serviced a
WHIRLPOOL COOKTOP
Model ABC123
Near Albuquerque, NM 87120
Larry
Job Details: 10/24/2024
CX complaint - Cooktop not lighting - Inspected unit and found there is no power coming into the unit - Advised cx to contact a qualified electrician. Collected SC auth-9FW9M3
We serviced a
WHIRLPOOL RANGE
Model WGE745C0FS01
Near Peyton, CO 80831
Jerimiah
Job Details: 10/24/2024
"Installed replacement main harness, hardwired thermal sensors, did temp check to 350, unit climbed past 380 avg. calibrated both ovens to -30 SR#7740116535, Techline requested thermal sensor resistance readings. Lower sensors set at 350 registered 1680 and upper was 1710. Techline deeming this unrepairable. Called AIG, they will contact Cust for solutions."
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW2
Near Peyton, CO 80831
Aaron
Job Details: 10/24/2024
"Built up fabric softener in unit, took agitator off and cleared debris, recommend cleaning cycles with product, levwled unit, tested unit through diagnostics, working well. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ02
Near Bend, OR 97701
Levi
Job Details: 10/24/2024
"Replaced damper, tested good"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HWO
Near Colorado Springs, CO 80921
Glenn
Job Details: 10/24/2024
"Installed New Cam Kit, Shifter, Motor & Belt, Test using a load of towels, All OPS Test:OK at this time."
We serviced a
LYNX GRILL
Model L600-NG00
Near Colorado Springs, CO 80915
Ralph
Job Details: 10/24/2024
INSTALLED LISTED PARTS AND UNIT CHECKED OKAY
We serviced a
THERMADOR RANGE
Model PRG486WLG/04
Near Grand Lake, CO 80447
Erik
Job Details: 10/24/2024
install PC board/ test: BAKE (both ovens) - PASStest timers: PASSset clock - GOOD/ no errorsJOB COMPLETECX not available for signature
We serviced a
BOSCH RANGE
Model HII8057U/03
Near Fraser, CO 80442
Erik
Job Details: 10/24/2024
install new slide kit/ test: PASSJOB COMPLETE
We serviced a
KITCHENAID ICE MACHINE
Model KUID308ESS2
Near Glenwood Springs, CO 81601
James R
Job Details: 10/24/2024
Put into service diagnostics. No water comes in. Also does not cool has a sealed system leak. Would need to replace following parts. service call $149.95 $255.00 labor $995.95 compressor W11735041 $480.40 Drier W10843121 $82.20 W10218037 $475.43 Total to repair. $2438.53Customer paid service call $149.95 auth code.34WC44
We serviced a
KITCHENAID DISHWASHER
Model KUDC10IXWH4
Near Glenwood Springs, CO 81601
James R
Job Details: 10/24/2024
No pwr removed control panel Found thermal fuse blown and control panel doesnt have some buttons dont work. Gave customer etimate. $705.56 will replace unit. Customer paid service call $149.95 auth code 4999HUPlease fill out tech satisfaction survey. Thank You.
We serviced a
FRIGIDAIRE DISHWASHER
Model FDSH450LAF4A
Near Colorado Springs, CO 80921
Charles
Job Details: 10/24/2024
"No pressure from wash motor, spray arms not moving. Need part number A10281701Service fee $129.95Labor$229.95Supplies $14.50Part 277.01Tax $22.71Total $674.13Declined repair at this time, paid service fee $129.95 autho CVFYH4"
We serviced a
FRIGIDAIRE DISHWASHER
Model FDSH450LAF4A
Near Colorado Springs, CO 80921
Charles
Job Details: 10/24/2024
"No pressure from wash motor, spray arms not moving. Need part number A10281701Service fee $129.95Labor$229.95Supplies $14.50Part 277.01Tax $22.71Total $674.13Declined repair at this time, paid service fee $129.95 autho CVFYH4"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AF4
Near Pueblo, CO 81005
James
Job Details: 10/24/2024
Found divider loose causingdoor to not close properly. Adjusted and secured divider
We serviced a
PROFILE WASHER
Model GFW850SSN5WW
Near Colorado Springs, CO 80904
David
Job Details: 10/24/2024
"Checked washer and ran diagnostics, all dispenser valves operating. Plug for tank, not making good contact, took apart and reconnected. Operating good now."
We serviced a
MONOGRAM REFRIGERATOR
Model ZISS480DNHSS
Near Aspen, CO 81611
Sean
Job Details: 10/24/2024
customer signed disclamerdisconected power to unit and removed ice machine and the evap fan motor. installed new fan motor. reinstalled ice machine. removed the door gasket from the cold compartment and installed new gasket. used a heat gun to mold gasket into shape. checked seal in door good.unhooked the control panel and installed new control into unit. reconnected the wiring to unit restored power to unit and tested.unit tested good fan is no longer reving up the cooler door is now sealing good. please fill out a tech servey.
We serviced a
U-LINE REFRIGERATOR
Model U-C01175B-00
Near Colorado Springs, CO 80904
Ralph
Job Details: 10/24/2024
"valve ws not correct part, cust tired of messing with this unit and is going to replace"
We serviced a
WOLF RANGE
Model DF304
Near Monument, CO 80132
Jerimiah
Job Details: 10/24/2024
"Cust was asking whats involved in taking apart door to be cleaned from gunk at bottom of door frame, this model has a screw under nameplate that would need removing before door can be separated. Cust is holding off on door cleaning charging service call. Chk#6005 $149.95 CK Auth# N93W9H"
We serviced a
KITCHENAID RANGE
Model KDRP467KSS04
Near Bend, OR 97701
Levi
Job Details: 10/24/2024
Replaced board that was rebuilt. Tested. All checks okay
We serviced a
GE RANGE
Model NOTAVALIBLE
Near Glenwood Springs, CO 81601
Sean
Job Details: 10/24/2024
checked unit foumd that the power switch to the oven light is burnt up and needs replaced.5304527841 rocker switch.customer declined repair.paid $199.95 cardauth code 4NUMVT transaction id 1544738
We serviced a
WHIRLPOOL DRYER
Model GEW9250PW1
Near Colorado Springs, CO 80911
Carlos
Job Details: 10/24/2024
Installed heater all ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Bend, OR 97701
Levi
Job Details: 10/24/2024
"Complaint is that not working but doesn't remember exactly, it's been a year that she hasn't used the machine. All functions tested good"
We serviced a
KITCHENAID ICE MACHINE
Model KUIX335HPS00
Near Colorado Springs, CO 80903
Ralph
Job Details: 10/24/2024
"unti has a faulty recirc pump, cust needc to discuss the repair...part W11542867 $187.38, tax $15.37, mps 14.50, labor $249.95, = 467.20 total remaining, cust paying service fee today of 149.95"
We serviced a
MIELE FREEZER
Model F1911 VI/39
Near Colorado Springs, CO 80906
Ralph
Job Details: 10/24/2024
"fan was not used, but the compressor kit and the control board were used will figure out the difference...autho no. 9TM4M9"
We serviced a
WHIRLPOOL WASHER
Model WFW6620HW3
Near Rifle, CO 81650
James R
Job Details: 10/24/2024
Printed labels took pics ready to send.
We serviced a
SAMSUNG REFRIGERATOR
Model RF265BEAESR/AA
Near Pueblo West, CO 81007
Brandon
Job Details: 10/24/2024
"Error 40c, 39c, replaced parts and cycled ice maker all checks ok hass oqc passed"
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FG/AA
Near Pueblo, CO 81005
Brandon
Job Details: 10/24/2024
Replaced door and tested op all checks ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5100SRAA
Near Pueblo West, CO 81007
Brandon
Job Details: 10/24/2024
"Repaired leak and replaced parts, vacuum unit for 10 minutes charge unit to spec 86 g hass oqc passed"
We serviced a
GE WASHER
Model WPXH214A0WW
Near Winter Park, CO 80482
Erik
Job Details: 10/24/2024
CALL CANCELLED - PARTS NLA
We serviced a
GE RANGE
Model JB645EK2ES
Near Colorado Springs, CO 80905
David
Job Details: 10/24/2024
"Replaced surface switch, tested and is operating correctly."
We serviced a
WHIRLPOOL WASHER
Model MHW6630HC3
Near Carbondale, CO 81623
James R
Job Details: 10/24/2024
Signed disclaimer.Tore apart and checked elec wiring and components took pics all look good. Test run unit is is sworking as should. Turned water off.Customer paid $149.95 auth code. 93P9P3Please fill out tech satisfaction survey. Thank You.
We serviced a
JENN-AIR WALL OVEN
Model JMW2430DS01
Near Colorado Springs, CO 80921
Jerimiah
Job Details: 10/24/2024
"Installed replacement console, unit check ok. Charged labor as quoted $209.95 CC Auth# FA443V"
We serviced a
MAYTAG REFRIGERATOR
Model PBB1951GRQ
Near Peyton, CO 80831
Aaron
Job Details: 10/24/2024
"Product temperatures at time of inspection -8.9f FC, 41.2f RC , damper control and belt are not responding , found FC control set to coldest setting, good push from evaporator fan motor, set FC control to recommended so less FC air is in RC section, customer to monitor, belt and damper is no longer available. Damper control 67001041 NLABelt Damper 67001040 NLAAuth $129.95 #HA3MR9"
We serviced a
MAYTAG DRYER
Model MEDB800VQ0
Near Albuquerque, NM 87105
Larry
Job Details: 10/24/2024
CX complaint - Dyer not starting - Instected unit and found the control failed and is NLA - Called 3rd party to confirm (SR7740144018) Unit is non-repairable
We serviced a
WHIRLPOOL WASHER
Model WTW8000DW5
Near Albuquerque, NM 87111
Jason
Job Details: 10/24/2024
installed lid unit checks ok; used 1 W11101059 (lid) from stock
We serviced a
MAYTAG DRYER
Model MEDB835DW4
Near Grants Pass, OR 97527
Austin
Job Details: 10/24/2024
"All the internal parts were replaced. The customer had brought the unit from the washer and dryer area into the living room. During that transfer the legs of the unit scratched a portion of the floors. When we went to put the unit back into the laundry room, I used the nylon plastic board to slide it across the ground. The unit was plugged in and tested. The unit passed all test. The customers dryer air vent is plugged up and they were advised that it should be cleaned out because the unit will not operate appropriately without it."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP560HAMZ0
Near Santa Fe, NM 87508
Joe
Job Details: 10/24/2024
"Cx complaint. Top rack stop is broke. Inspected unit, stop is broke. Replaced stop and tested. Rack stays in place now. Unit good to go"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS311SDHT10
Near Santa Fe, NM 87508
Joe
Job Details: 10/24/2024
"Cx complaint. Refrigerator not making ice. Inspected unit, found water dispenser working fine but not making ice. Ice maker not working in test mode. Replaced ice maker and water valve. Tested ice maker in test mode. Ice maker harvesting and filling fine. Unit good to go"
We serviced a
WHIRLPOOL WASHER
Model WTW4655JW2
Near Albuquerque, NM 87113
Jason
Job Details: 10/24/2024
Checked unit counld not verify cx complain no error codes present ran diagnostic cycle unit opperation checks ok
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Santa Fe, NM 87507
Joe
Job Details: 10/24/2024
"Cx complaint. Dishwasher not drying dishes. Inspected unit. No errors, went though diagnostic cycle fine. Per tech support, unit working as designedSr7740184067"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, NM 87105
Larry
Job Details: 10/24/2024
"Installed control, ran test cycle and tested good - Unit is operating as designed"
We serviced a
WHIRLPOOL FREEZER
Model WZF34X20DW06
Near Albuquerque, NM 87112
Jason
Job Details: 10/24/2024
checked unit temps and breakdowns no indication of a light under unit anywhere unit opperation checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ04
Near Santa Fe, NM 87507
Joe
Job Details: 10/24/2024
"Cx complaint. Refrigerator making noise when door was opened. Inspected unit, unable to duplicate issue. Cx will call back if noise returns.Advised cx about survey"
We serviced a
MAYTAG WASHER
Model MVW6500MBK0
Near Albuquerque, NM 87105
Larry
Job Details: 10/24/2024
"CX complaint - Washer making grinding sound - Inspected unit and found the shifter failed causing damage to the cam - Replaced with pre-id parts, ran test cycle and tested good - Unit is good to go"
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Albuquerque, NM 87113
Jason
Job Details: 10/24/2024
Checked unit found lid lock was out of place re attached lid lock unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ22
Near Santa Fe, NM 87507
Joe
Job Details: 10/24/2024
"Cx complaint. Dishwasher not drying dishes. Replaced heater, control and vent ordered last visit. Tested unit. No errors and went though test cycle fine. Unit good to goAdvised cx about survey"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ02
Near Colorado Springs, CO 80922
Charles
Job Details: 10/24/2024
Replaced main control board
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Yoder, CO 80864
Aaron
Job Details: 10/24/2024
"F8E1F7E6 error codes upon arrival, inspected unit, pulley and belt are worn and loud during spin, removed and replaced components, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW2
Near Monument, CO 80132
Glenn
Job Details: 10/24/2024
"Install New Main Control, Ran Quick Cycle Test> Pass, Customer witll continue to monitor."
We serviced a
KITCHENAID COOKTOP
Model KCGS550ESS05
Near Winter Park, CO 80482
Antonio
Job Details: 10/24/2024
Installed new ignitor tested by turning on for proper operation and unit tested good
We serviced a
KITCHENAID M/W OTR
Model KMMF530PBS00
Near Grand Lake, CO 80447
Antonio
Job Details: 10/24/2024
Installed new grill unit looks great
We serviced a
KITCHENAID RANGE
Model KFGC506JSS05
Near Grand Lake, CO 80447
Antonio
Job Details: 10/24/2024
Installed ignitor and module ran unit tov350 degrees for proper operation and unit tested good
We serviced a
MAYTAG WASHER
Model MVW6230HC3
Near Aspen, CO 81611
Sean
Job Details: 10/24/2024
customer signed discloser.customer showed me clothes that where not rinsed completely. checked unit= unit had no error codes saved. started unit noteced that the unit was about 1' low on front side. leveled unit.started new cycle and unit filled and opperated as designed. callebrated controles tested goodcstomer contacted ( Mountain high appliance ) to make payment $239.95.please fill out a tech servey
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF705HPS04
Near Monument, CO 80132
Glenn
Job Details: 10/24/2024
"Items still staying cold. Temps 6F FRZR / 36F FF , Unable to find anything out of the ordinary. Inspected Frzr Evap , Heater, Fan, Drain. Checked connections. Techline: SR# 7740184491 , Suggest that if Sealed system was leaking, Temps would be higher than normal & unit wouldnt be cooling properly. Coolant is also safe for release into air, should it ever leak out. Transferred to Safety > Logged info. All OPS Test: OK at this time."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Colorado Springs, CO 80918
Glenn
Job Details: 10/24/2024
"install new lower spray arm, All OPS Test:OK"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ
Near Colorado Springs, CO 80916
Carlos
Job Details: 10/24/2024
Installed compressor and charged
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Pueblo West, CO 81007
James
Job Details: 10/24/2024
Found mice in unit advised cust whirlpool will not pay for repair
We serviced a
WHIRLPOOL RANGE
Model WFES5030RZ0
Near Peyton, CO 80831
Aaron
Job Details: 10/24/2024
"Warming drawer panel bent, removed and replaced panel, no scratches or dents, verified by customer, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM08
Near Fountain, CO 80817
Carlos
Job Details: 10/24/2024
"Installed fan, thermistor and temp control"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS2
Near Colorado Springs, CO 80908
Aaron
Job Details: 10/24/2024
"Handle loose, tightened and tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
KITCHENAID RANGE
Model KSGG700ESS6
Near Colorado Springs, CO 80908
Aaron
Job Details: 10/24/2024
"Front left burner orifice clogged, cleared and tested unit, advised customer of usage with double orifice burners, transition is good, has a true vent above that can flicker flame with air movement. Advised customer of 5 star survey.. SR7740179693"
We serviced a
WHIRLPOOL RANGE
Model WEE745H0LZ4
Near Colorado Springs, CO 80920
Jerimiah
Job Details: 10/24/2024
Installed replacement controller did temp check on unit. Heats up properly as expected. Unit check ok.
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS2
Near Bend, OR 97702
Levi
Job Details: 10/24/2024
Replaced main control board tested all checks okay all functions testing good
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Rogue River, OR 97537
Austin
Job Details: 10/24/2024
The unit had no error codes and was ran through three diagnostic cycles with no issues. The units drain line was a little far down and it was readjusted to allow it to drain better as well as the unit was confirmed to be leveled. The customer said the last times shes been running the unit. It has been working perfectly fine. I let the customer know to advise us if the unit started having issues again..
We serviced a
SEARS RANGE
Model 79094002601
Near Rifle, CO 81650
James R
Job Details: 10/23/2024
Signed disclaimer. Top burner issue. Found a couple of front burners wiring attached to the wrong burners swapped and then L.F. burner switch is bad replaced customer had part. Tested operation are all ok. Please fill out tech satisfaction survey. Thank You. Customer paid. $289.90 Auth code. 349EE3
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Los Lunas, NM 87031
Larry
Job Details: 10/23/2024
"Installed parts listed, ran test cycle and tested good - Unit is good to go"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW08
Near Terrebonne, OR 97760
Austin
Job Details: 10/23/2024
Unit not cooling. Found wire to defrost heater out of connected. Reconnected correctly. Manually defrosted/steamed freezer compartment evaporated from ice build up. Tested all components. All ops sat per factory spec
We serviced a
MAYTAG WASHER
Model MVWB855DC4
Near Peyton, CO 80831
Aaron
Job Details: 10/23/2024
"Removed and replaced UI control assembly, tested unit through diagnostics, working well now, customer verified. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Colorado Springs, CO 80911
Carlos
Job Details: 10/23/2024
Installed harness ran test all ok
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Colorado Springs, CO 80917
Glenn
Job Details: 10/23/2024
"Install New Control > No Change, Install Cam Kit & Shifter > Same, Install New Harness > Unit Now functional. Calibrated Unit, Diag Test>Pass, All OPS Test:OK"
We serviced a
SAMSUNG WASHER
Model WF45R6100AC/US
Near Redmond, OR 97756
Levi
Job Details: 10/23/2024
Found inlet valve was clogged. Could not replicate a noise the customer complained about. She pointed to a location near the valves and I informed her that it was probably due to the valve not getting adequate water volume through it.
We serviced a
MAYTAG RANGE
Model MER8800FZ5
Near Socorro, NM 87801
Larry
Job Details: 10/23/2024
CX complaint - Oven too hot - Inspected unit and found F1E0 and F2E1 - Unit needs UI and control - CX doesn't want to bear the cost of repair - Collected SC - Estimeat in QP
We serviced a
MAYTAG DRYER
Model Med7230hw1
Near Colorado Springs, CO 80924
Aaron
Job Details: 10/23/2024
"F2E1 error code upon arrival, upon inspection, found the heating element shorted out, thermostats check out okay, approved onsite, cleared unit of lint and replaced element, tested unit, working and heating well now. Element wp3387747 $103.58Tax $8.49Supplies $14.50Hc $129.95Labor $199.95Total job $456.47No return on parts Auth total due $456.47 #T9N9L9"
We serviced a
BOSCH REFRIGERATOR
Model B36BT935NS/31
Near Edwards, CO 81632
Erik
Job Details: 10/23/2024
install door panel * see quick picsJOB COMPLETECX not available for signature
We serviced a
BOSCH DISHWASHER
Model SHP878ZP5N/22
Near Avon, CO 81620
Erik
Job Details: 10/23/2024
unit not powering up - check breaker/ outlet * see quick picsno power to outlet maker dishwasher on breaker (switch to disposal outlet test: PASSJOB COMPLETECX not available for signature / CX aware that electrician is needed to address outlet * newly remodeled kitchen
We serviced a
BOSCH COOKTOP
Model NGM8048UC/01
Near Divide, CO 80814
Ralph
Job Details: 10/23/2024
"installed listed part and unit checked okay, did not need to remove unit from its position to do this repair."
We serviced a
THERMADOR MICRO DRAWER
Model MD24WS/04
Near Colorado Springs, CO 80921
Charles
Job Details: 10/23/2024
"Will not heat all the time, adjusted right side interlock switch assembly and tested"
We serviced a
DACOR RANGE
Model ERD48SBK/H
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 10/23/2024
Large bake element burned out needs replacing. Part is NLA Cust will look for replacement component. Charging service call. $172.44 CC Auth# CXK44K labor will be $229.95DE81-04482A bake element NLA
We serviced a
WHIRLPOOL GAS RANGE
Model FDUJIIIFDD
Near Edwards, CO 81632
Antonio
Job Details: 10/23/2024
Looked at unit unut needs burners cleaned cx did not want to proceed with clean/repair