We serviced a
GE REFRIGERATOR/TOP
Model PYE22KYNIFS
Near Colorado Springs, Colorado 80906
Roman
Job Details:
11/10/2023
"Checked the ice bin and dispenser and the fridge is still freezing the lines. Added some styrofoam foam and raised the temps in the fridge. Did not use the new gasket, old one is sealing great after using vasaline on it."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9070SG/AA
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
11/10/2023
Replaced icemaker parts. Test op all okay.
We serviced a
BOSCH DISHWASHER
Model SHPM78Z55N/22
Near Colorado Springs, Colorado 80906
Roman
Job Details:
11/10/2023
Ran dw through the diagnostic mode and its went through all the cycles without error codes. Noticed that the water was taking a long time to drain out. Checked the drain line and it was a mess so removed the drain line and attached it onto the disposal. Tested the dw and it drained out way faster and working great. Checked under neath it for leaks and checked the drain pump drain pump looks fine and had nothing stuck in it. Dw working great.
We serviced a
ASKO DISHWASHER
Model D5656XXLHS
Near Colorado Springs, Colorado 80906
Roman
Job Details:
11/10/2023
"Pulled the dw out and the float is touching the switch to the leak sensor. Dw leaking from the divider. Recommend replacing the divider, inlet valve and float. Valve #434374. $115.00Divider #700497 $159.00Float #700354 $72.50Tax $28.41Total parts $ 374.91MPs $14.50Labor $449.95Sc $149.95Total cost $989.31 Paid sc $149.95 CC Auth# F9JC33"
We serviced a
GE REFRIGERATOR/TOP
Model FUF21QRRAWW
Near Colorado Springs, Colorado 80906
Roman
Job Details:
11/10/2023
Installed new door gasket and door is opening easier.
We serviced a
MAYTAG WASHER
Model MVWC565FW
Near Colorado Springs, Colorado 80907
Roman
Job Details:
11/10/2023
Cx wondering why theres not that much water. Explained to her that you have to fill the tub with more clothes to have it fill up more and explained which cycles to use for the amount of clothing.
We serviced a
WOLF WALLOVEN
Model DO30F/S
Near Colorado Springs, Colorado 80906
Roman
Job Details:
11/09/2023
"Removed the wall oven and the terminal block is melted and needs all new caps. Checked elements and thermostats and the upper oven thermostat tripped. Reset it and put the oven back. Installed the power cord with new connectors and tested the top and bottom oven, both working great. Labor $249.95X2 MPs $14.50Sc $149.95Total cost $664.35Paid cc $664.35 CC Auth# 94CV3N"
We serviced a
GE REFRIGERATOR
Model GYE22HSKJSS
Near Colorado Springs, Colorado 80906
Roman
Job Details:
11/09/2023
"Tried testing the ice maker but couldnt get it to move the fingers, recommend replacing the ice maker. Ice maker #WR49X31524 $174.74Tax $14.33Total part $189.07Labor $169.05MPs $14.50Sc $129.95Total cost $503.47 not sure if they wanted to to the repairpaid sc $129.95 CC Auth# 3934PY"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LFSC2324VF5
Near Colorado Springs, Colorado 80903
Roman
Job Details:
11/09/2023
Ran the fridge In diagnostics and when the compressor kicks on it rattles quit a bit right when it starts up but then sounds normal after it gets going. Fridge and freezer both cooling checked all fans and they are all running. Capacitor and compressor are good. Made sure everything was tight and secure. I dont see anything wrong with it
We serviced a
WHIRLPOOL RANGE
Model WGG745S0FS10
Near Cripple Creek, Colorado 80813
Ralph
Job Details:
11/09/2023
"USING A SMALL SCREWDRIVER, WENT INTO THE SHQFT OF BOTH THE REAR VALVES AND MADE THE FLAME LARGER FOR THE CUST, UNIT CHECKED OKAY"
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS2
Near Florissant, Colorado 80816
Ralph
Job Details:
11/09/2023
REPLACED LISTED PARTS AND UNIT CHECKED OKAY
We serviced a
WOLF RANGE
Model DF304
Near Woodland Park, Colorado 80863
Ralph
Job Details:
11/09/2023
INSTAQLLED PARTS AND UNIT CHECKED OKAY
We serviced a
GE REFRIGERATOR
Model GIE19JSNBRSS
Near Winter Park, Colorado 80482
Erik
Job Details:
11/09/2023
installjob complete
We serviced a
GE WASHER-DRYER COM
Model GUD27EESN0WW
Near Winter Park, Colorado 80482
Erik
Job Details:
11/09/2023
shipping rod still instlled/ loose connection at MCB dryer L2 short/ over voltjob complete
We serviced a
GENERAL ELECTRIC RANGE HOOD
Model JVX5305SJSS
Near Winter Park, Colorado 80482
Erik
Job Details:
11/09/2023
installed on a secondary switch/ outletidentify line supply to lighting/ fan motor (seperate)consolodate lines/ test: Goodjob complete
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS09
Near Rio Rancho, New Mexico 87144
Larry
Job Details:
11/09/2023
Unit is tripping the breaker when plugging it in - Checked and found the mag failed damaging the wave guide - Called tech line (SR7737758563) - Unit is non-repairable
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS0
Near Albuquerque, New Mexico 87120
Larry
Job Details:
11/09/2023
CX complaint - Lights flashing - Inspected unit and found the float switch had debris under it - Cleared debris and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model WED5605MC0
Near Elbert, Colorado 80106
Aaron
Job Details:
11/09/2023
"Revolvers have worn, removed and replaced rollers and idler, lubricated and tested, working and heating well. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Elbert, Colorado 80106
Aaron
Job Details:
11/09/2023
"Water inlet flume clip not fully secure, drain hose in standpipe, corrected both issues and tested unit, working well. Advised customer of usage with new 'he' unit's and of survey."
We serviced a
GE WASHER
Model PTW700BST0WS
Near Colorado Springs, Colorado 80906
David
Job Details:
11/09/2023
"Checked washer Ck stated that machine is walking forward Ran diagnostics all ran good Error codes showing43 inverter faults 92 inverter heartbeat failure 26 out of balance, redistribution 31 out of balance, fallback in final spinCalled tech line His suggestion is to use deep fill and deep rinse so the clothes don't knot up as bad Case number 11469742"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Albuquerque, New Mexico 87121
Larry
Job Details:
11/09/2023
CX complaint - DW wont run - Inspected unit and found the sump and control failed - Replaced both and tested good - Unit is good to go
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Edgewood, New Mexico 87015
Jason
Job Details:
11/09/2023
installed burner unit checks ok
We serviced a
SAMSUNG RANGE GAS
Model NX60A6311SS/AA
Near Colorado Springs, Colorado 80925
Jerimiah
Job Details:
11/09/2023
"Buttons randomly not working, cycled power on unit and buttons are working again. Previously replaced keypad and controller are under 90 day warranty til 12-12-23. Techline says display could possibly cause communication disruption between components. Cust will look for new appliance. Charging service call. Labor will be $189.95 upon return service if decided. $136.45 CC Auth# 44A3VKDG94-04041C Control boardDG96-00850D KeypadNotes:DG92-01232C Display"
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ2
Near Fraser, Colorado 80442
Antonio
Job Details:
11/09/2023
Installed new ui panel unit tested good
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ0
Near Cañon City, Colorado 81212
James
Job Details:
11/09/2023
installed ordered parts. tested ops. all ckok temps cycling at 375 and 325
We serviced a
WHIRLPOOL ICEMAKER
Model WUI95X15HZ01
Near Albuquerque, New Mexico 87111
Jason
Job Details:
11/09/2023
cx is experiancing an issue where unit shuts all lights off then comes back on. i suspect control is havung an issue. unit is making ice at this time. cx may call wp for a parts concession
We serviced a
KITCHENAID VENT HOODS
Model UXB1170KYS0
Near Granby, Colorado 80446
Antonio
Job Details:
11/09/2023
Found plastic grill rubbing due to wires pressing against it moved wires unit tested good
We serviced a
WHIRLPOOL DRYER
Model WED4616FW0
Near Albuquerque, New Mexico 87108
Jason
Job Details:
11/09/2023
installed parts unit checks ok
We serviced a
DACOR DOWNDRAFT VENT
Model RV36W
Near Elbert, Colorado 80106
Kris
Job Details:
11/09/2023
319.95 for labor msp14.50 cx ordering motor will need 2 hours clean contacts under ui main board de81-07744a 317.78motor de81-06588a 346.99
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Peyton, Colorado 80831
Aaron
Job Details:
11/09/2023
"Crack in Inner corner of unit, removed and replaced lid assembly, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Carbondale, Colorado 81623
James R
Job Details:
11/09/2023
Checked exaust temp. Cycling too fast. Replaced cutoff. Checked temp lo 132 hi 155 good. Put in a load of sheets and run on auto delicates cycle. Sensing light has come on and now wet. Temp is coming up as should as cloths dry. Need to be sure to dry like cloths. Sheets are thin and will dry quicker than thicker cottons. On auto cycle if the thicker items dont touch the sensing bar the unit will shut off before cloths are dry. Checked the vent restriction it is borderline high .60 which will affect the drying. .58 is max. Also too large of loads if they touch the front vent for too long will affect drying as well. Need to be able to tumble and have a clear screen at times. customer signed waiver. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL RESIDENTIAL REFR
Model WRF767SDHZ03
Near Peyton, Colorado 80831
Kris
Job Details:
11/09/2023
installed compressor and all parts sent charged with 56g of r600 ran tets op all ok unit is working to spec at this time. cx will monitor unit for 24 hours.
We serviced a
SPEEDQUEEN DRYER - ELECTRIC
Model ADE4BRGS175TW01
Near Colorado Springs, Colorado 80921
Mathew
Job Details:
11/09/2023
Replaced outlet cover. Test op all okay.
We serviced a
SAMSUNG WASHER
Model WF219ANW/XAA 01
Near Colorado Springs, Colorado 80921
Mathew
Job Details:
11/09/2023
Found bad tub seal. Unit needs new tub assy or rear tub assy. Could not find part available. Svf 129.95. Cx not repairing.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SR/AA
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
11/09/2023
"Found reed switch unplugged. Plugged switch in and test op, unit working as expected."
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Carbondale, Colorado 81623
James R
Job Details:
11/09/2023
Is in building 900 unit 316 Checked temp is cycling to quickly. Replaced cutoff. 280148 Checked temp timed dry lo 130 hi 156 good. Vent removed. Checked operation of unit in auto cycle with towels in it. Sensing light came on and then wet. So unit is sensing the dampness of the items. Make sure Eco boost is off. Items must touch sensing bars in order to dry properly. Also dry like cloths. A mixed load of thinner and heaver items will not dry the same. If heavier items dont touch the bar it will shut down before items are dry. Checked vent restriction it is hi .60 max should be .58 Will affect the drying. Customer dsigned waiver. Please fill out whirlpool tech satisfaction survey. Thank You. ; used 1 280148 (CUTOFF-TML) from stock
We serviced a
FRIGIDAIRE MICROWAVE OVEN
Model GMOS1964AFA
Near Cañon City, Colorado 81212
James
Job Details:
11/09/2023
"installed ordered parts, adjusted hinge and tested. all ops test good. good temp rise observed."
We serviced a
SAMSUNG WASHER
Model WA45T3400AP/A4
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
11/09/2023
"Pillow Case stuck inside of drive belt. Removed and test op, all okay. Collected svf $129.95$129.95 CC Auth# JR4M93"
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6200QLAA
Near Colorado Springs, Colorado 80924
Mathew
Job Details:
11/09/2023
Replaced left door. Test op all okay.
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Colorado Springs, Colorado 80918
Glenn
Job Details:
11/09/2023
"Install New Gearcase, Basket, Hub Kit, Splutch kit, Actuator, Belt & Suspension. All OPS Test:OK, No Leaks."
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950UG/AA
Near Colorado Springs, Colorado 80918
Glenn
Job Details:
11/09/2023
"Installed New Water valve. Informed customer that shutoff valve under sink not turning off all the way, suggest have plumber replace shutoff valve. Test Unit, No Leaks. All OPS Test:OK, Installed Leak Detector for safety."
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Colorado Springs, Colorado 80951
Carlos
Job Details:
11/09/2023
"Ran test op. Found broken wire, repaired wire runs ok."
We serviced a
SAMSUNG WASHER
Model WF45M5500AW/A5
Near Colorado Springs, Colorado 80923
Mathew
Job Details:
11/09/2023
Needs Washer diaphragm DC97-19755a. Quote good for 30 days. Cx not moving forward at the moment. Paid svf 129.95 $129.95 CC Auth# V39K43DC97-19755a 256.78 plus tax 21.06. Parts total 277.84Svf 129.95MPs 14.50Due today $422.29 ($292.34 remaining after svf)Due on install Labor $179.95
We serviced a
SAMSUNG GAS RANGE
Model NX60A6311SS/AA
Near Colorado Springs, Colorado 80925
Jerimiah
Job Details:
11/09/2023
Installed replacement controller w/ display. Unit check ok.
We serviced a
MAYTAG WASHER
Model MVWC465HW3
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
11/09/2023
"Cx explained that washer leaks on front right corner and back left corner. Inspected drain houses, outer tub, motor drive, pressure hose and water hoses all dry, could not determine exact location of leak although there is evidence of water on the floor. Replaced tub ring and water valve Cx will observe."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
11/09/2023
Installed sump assembly and control board runs all ok
We serviced a
SAMSUNG DRYER - ELECTRIC
Model DVE50R5200
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
11/09/2023
"Model and serial didn't match, told cx they have to update it with aig warranty"
We serviced a
WHIRLPOOL MICROWAVE OVEN
Model KMBP100ESS20
Near Colorado Springs, Colorado 80908
Jerimiah
Job Details:
11/09/2023
Installed replacement inverter board. Unit check ok.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
11/09/2023
Installed bin. Put food products to add weight all ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA 19
Near Fountain, Colorado 80817
Brandon
Job Details:
11/09/2023
Replaced parts and tested op all ok hass passed
We serviced a
SAMSUNG REFRIGERATOR
Model RS23CB760012
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
11/09/2023
"Complaint is freezer is too cold, unit has ice maker which is designed to drop temp in freezer to -17 when ice maker is turned on, called tech support to confirm, checked all sensors all test ok"
We serviced a
SAMSUNG DISHWASHER - BUI
Model DW80M2020U
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
11/09/2023
"Found signs of leaking at drain pump, removed drain pump cleaned seal reinstalled drain pump tested op all ok checked for leaks all ok"
We serviced a
SAMSUNG DRYER
Model DVE45A6400W/A3
Near Monument, Colorado 80132
Brandon
Job Details:
11/09/2023
"Thermostat 3 is bad again, unit overheating, all other sensors test ok, recommend getting vent cleaning done"
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA
Near Colorado Springs, Colorado 80921
Brandon
Job Details:
11/09/2023
"Found vane deflector not connected, connected the deflector and tested op all ok hass passed"
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Colorado Springs, Colorado 80920
Glenn
Job Details:
11/09/2023
"Install New Gearcase, Splutch Kit, Shifter, Cap & Belt. All OPS Test:OK, No Leaks."
We serviced a
SAMSUNG REFRIGERATOR
Model RF31CG7400SRAA
Near Monument, Colorado 80132
Glenn
Job Details:
11/09/2023
"Install New Center Drawer Panel. All OPS Test:OK , Customer Satisfied with end results."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Monument, Colorado 80132
Glenn
Job Details:
11/09/2023
"Power was cycled on unit, all ops test:OK."
We serviced a
GENERAL ELECTRIC WASHER
Model PFW950SPT1DS
Near Colorado Springs, Colorado 80918
David
Job Details:
11/09/2023
Replaced motor and drive belt Ran cycle and is running nicely
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Colorado Springs, Colorado 80951
Roman
Job Details:
11/09/2023
Ran the washer in diagnostic mode and it did not show error codes. Ran it through all the cycles and it worked fine. Washer does shake when in spin mode. Noticed the feet in the front were raised more the the feet in the back. Leveled the washer and tested it.Threw in some towels and ran a rinse and spin mode on them washer seems fine. Recommend to cx trying different cycles with the amount of clothes and towels that are in it.
We serviced a
WHIRLPOOL DRYER
Model MED3500FW0
Near Colorado Springs, Colorado 80919
Carlos
Job Details:
11/09/2023
"Installed idler pulley, ran test op all ok. Cx paid"
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
11/09/2023
"Line loose at terminal block, shorted and melted wire and terminal, replaced terminal block and wires, customer unavailable to advise of survey or obtain signature."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SR/AA
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
11/08/2023
"Replaced compressor and dyer, repaired leak, held vacuum for 15 minutes, charged unit, compressor is removing heat and temps dropping, cx will monitor"
We serviced a
SAMSUNG MICROWAVE
Model ME21R7051SG/AA
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
11/08/2023
Replaced door assy and tested op no errors all ok
We serviced a
WHIRLPOOL DRYER
Model WGD5605MC0
Near Eagle, Colorado 81631
Antonio
Job Details:
11/08/2023
Installed flame sensor tstat and high limit unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Avon, Colorado 81620
Antonio
Job Details:
11/08/2023
Installed new acu actuator and capacitor unit tested
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Vail, Colorado 81657
Antonio
Job Details:
11/08/2023
Installed ui panel and cosole unit tested good Lb$189.95Tp$17.50$207.45 CC Auth# VAJ3XV
We serviced a
AMANA DISHWASHER
Model ADB1400AMW0
Near Aspen, Colorado 81611
James R
Job Details:
11/08/2023
Replaced both sprayer arms. Test run ok. Operation is normal. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Carbondale, Colorado 81623
James R
Job Details:
11/08/2023
Unit is setting outside. Will not work properly in temp 50 degrees or colder. Frig will sense the ambient temp and not run long enough to frz items in Freezer.Checked freezer temp 26.7 degrees.Customer needs to move unit inside to warmer temperature. At least 60 degrees. If customer is having further issues once in the right environment need to schedule a service.
We serviced a
JENN-AIR DISHWASHER
Model JDPSG244LS2
Near Carbondale, Colorado 81623
James R
Job Details:
11/08/2023
Replaced sump motor asy. Reinstall unit. Test run in diagnostics operating as it should. No error codes. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
ILVE RANGE GAS
Model UPDW90FDMP/I
Near Colorado Springs, Colorado 80903
Jessie
Job Details:
11/08/2023
Customer was not holding ignition system until thermal coupler was warm. Instructed. Called techline and was informed there are no adjustments to simmer. But they provide simmer plates. Customer going to order
We serviced a
WOLF COOKTOP
Model SRT486G
Near Monument, Colorado 80132
Jerimiah
Job Details:
11/08/2023
Installed replacement grille assy. Unit check ok.
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS20
Near Colorado Springs, Colorado 80924
Jerimiah
Job Details:
11/08/2023
Installed replacement door and door switch assy. Unit check ok.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Albuquerque, New Mexico 87111
Jason
Job Details:
11/08/2023
installed parts unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQA59CNKZ
Near Albuquerque, New Mexico 87112
Jason
Job Details:
11/08/2023
installed door unit checks ok
We serviced a
MAYTAG DRYER
Model MED7230HC
Near Socorro, New Mexico 87801
Larry
Job Details:
11/08/2023
CX complaint - f2 e2 error code - Inspected unit and found controls failed - Replaced with pre-id parts and tested good - Unjit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Los Lunas, New Mexico 87031
Larry
Job Details:
11/08/2023
CX complaint - Washer knocking aroung - Inspected unit and found the unit out of calibration - Calibrated unit and tested good - Unit is good to go
We serviced a
KITCHENAID RANGE
Model KGRS505XSS02
Near Albuquerque, New Mexico 87110
Jason
Job Details:
11/08/2023
installed part unit checks ok
We serviced a
FRIGIDAIRE WASHER
Model FFFW5100PWO
Near Colorado Springs, Colorado 80918
Jessie
Job Details:
11/08/2023
Drain pump# 137311900 239.58Pressure switch# 1347620 142.28Total parts 381.86Sc129.95 Tax 13.31Msrp 14.50Labor 209.90Total 767.57I was able to verify the issue Customer declined estimate
We serviced a
JENN-AIR DISHWASHER
Model JDB9800CWP2
Near Los Lunas, New Mexico 87031
Larry
Job Details:
11/08/2023
Installed control and tested good - Unit is good to go
We serviced a
WHIRLPOOL RANGE
Model WEG730H0DS0
Near Bosque Farms, New Mexico 87068
Larry
Job Details:
11/08/2023
Installed fan and tested good - Unit is good to go
We serviced a
BOSCH RANGE
Model HII8057U/05
Near Gypsum, Colorado 81637
Erik
Job Details:
11/08/2023
L1 to nverter 2 not attached to terminal block (power supply)*see quick picsreinstall/test: GOODJOB COMPLETE
We serviced a
BOSCH WASHER
Model WAT28400UC/26
Near Avon, Colorado 81620
Erik
Job Details:
11/08/2023
washer test: 30 min cycleRESULT: wash complete after 30 min. - nothing in the unit to test loaded so spin cycle continues attempting to sense a load - NORMAL FUNCTIONno error codes present at the time of testing
We serviced a
WHIRLPOOL DRYER
Model MEDE201YW0
Near Colorado Springs, Colorado 80918
Glenn
Job Details:
11/08/2023
"Unit makes loud screeching noise.Found lint buildup inside unit. suggest replace Support Rollers, Shafts, Idler Pulley & Belt. , Support Roller - WPW10314173 $56.70 each x4 = $226.80 , Idler Pulley Assy - W10837240 $68.06 , Belt - WPW10112954 $110.66,Shaft (Rear - LHT) - WPW10359272 $84.28 ea. X2 =$168.56 , Shaft (Front - RHT) - WPW10359271 $84.76 X2 =$169.52 , Tax $60.98 , MPS $14.50 , Labor $219.95 , Declined Estimate, Paid SC Fee of $149.95 + Tip $7.50 = $157.45 , Autho#4JU4HL"
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ1
Near Colorado Springs, Colorado 80923
Kris
Job Details:
11/08/2023
installed valve ran test op all burners and oven preheat to 200 all ok at this time.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Rocky Ford, Colorado 81067
James
Job Details:
11/08/2023
"found outlet insufficient for power delivery to unit. got 90vac between L1-L2 0vac L1-N &120vac L2-N. advised cust to have licensed electrician out to address. checked thermal fuse, heating element, thermostat & timer all ckok"
We serviced a
SHARP MICROWAVE
Model R-930CS-P
Near Colorado Springs, Colorado 80906
Jerimiah
Job Details:
11/08/2023
"Unit not convect baking or microwaving, found interlock switches dead, replaced all switches, unit check ok. $474.24 CC Auth# E9W3M3 charged service call parts labor tax MPsW279238082 interlock switches $40.00 x3; used 3 W279238082 (Interlock switch) from stock"
We serviced a
SAMSUNG RANGE
Model NX58H5600SS/AA
Near Monument, Colorado 80132
Brandon
Job Details:
11/08/2023
Replaced ignitor and tested op to 250 all ok
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Rocky Ford, Colorado 81067
James
Job Details:
11/08/2023
Installed ordered parts tested operations I'll check okay
We serviced a
WHIRLPOOL WASHER
Model WTW4655JW2
Near Pueblo, Colorado 81004
David
Job Details:
11/08/2023
Replaced water valve Tested and cold is coming on full strength every time
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Pueblo, Colorado 81001
David
Job Details:
11/08/2023
Checked dryer Heater and thermostats burned-out Replaced Tested and heating good Suggest having dryer vent cleaned
We serviced a
SCOTSMAN ICEMAKER
Model DCE33A-1SSD
Near Colorado Springs, Colorado 80908
Kris
Job Details:
11/08/2023
drain tube was not seated causing water to stay in bottom of bin melting ice cubes.
We serviced a
LIEBHERR REFRIGERATOR BOT
Model CS 2081
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
11/08/2023
believe ice mkr was turned off cust to monitor andcall with any issues...autho no. 99u39h
We serviced a
JENNAIR MICROWAVE
Model JMC2430DS01
Near Colorado Springs, Colorado 80919
Jerimiah
Job Details:
11/08/2023
"Installed replacement console,unit check ok charged sc and labor as quoted $339.90 CC Auth# F34AUT"
We serviced a
SAMSUNG RANGE - GAS
Model NX58M6850SG/AA
Near Colorado Springs, Colorado 80920
Jerimiah
Job Details:
11/08/2023
"Cust still has weak hinges, called techline to verify correct parts for hinges were given and no extra strength hinges available. Charging service call.$129.95 CC Auth# 4K99RY"
We serviced a
SAMSUNG WASHER
Model WA52J8700AP/A2
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
11/08/2023
Cx did not have proof of purchase but says Samsung gave them another year due to the unit being recalled
We serviced a
SAMSUNG WASHER
Model WA55A7700AV
Near Colorado Springs, Colorado 80919
Mathew
Job Details:
11/08/2023
Replaced tub assembly. Test op all okay.
We serviced a
JENNAIR DISHWASHER
Model JD8700AWS1
Near Manitou Springs, Colorado 80829
Carlos
Job Details:
11/08/2023
Ran test op all ok everything is operational Cx paid $149.95 CK Auth# 933KA9
We serviced a
AMANA WASHER
Model NFW5800HW1
Near Pueblo, Colorado 81001
David
Job Details:
11/08/2023
"Door would not unlock due to washer not draining Got water out, cleaned pump trapTested and is working good"
We serviced a
DACOR GAS COOKTOP
Model DTG36M955FS/DA
Near Colorado Springs, Colorado 80923
Jerimiah
Job Details:
11/08/2023
"Found burner heads turned upside down on most of them, repaired, cleaned one burner head, and also reinstalled ignition wire properly. Unit check ok."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ2
Near Pueblo, Colorado 81005
James
Job Details:
11/08/2023
installed ordered parts all ops test good. left litmus