Service History 480

We serviced a

SAMSUNG WASHER

Model WF45N5300AW/US

Near Pueblo, Colorado 81004

James

Job Details: 11/01/2023

found loose wire at door lock mech causing door locks to interminently not open. secured and tested. Ops ckok

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF507HPS02

Near Pueblo, Colorado 81008

David

Job Details: 11/01/2023

Replaced control Ran diagnostics All good

We serviced a

WHIRLPOOL DISHWASHER

Model WDPA70SAMZ1

Near Glenwood Springs, Colorado 81601

James R

Job Details: 11/01/2023

Replaced UI control. Unit now starts. Test cycle thru service diagnostics. Ok no issues working as should. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT112CZJZ00

Near Colorado Springs, Colorado 80923

Aaron

Job Details: 11/01/2023

"Defrost drain clogged, excessive moisture causing frost, no cooling in RC. Cleared ice, working well now . Advised customer of 5 star survey."

We serviced a

WHIRLPOOL DISHWASHER

Model ADB1400AMB0

Near Colorado Springs, Colorado 80915

Carlos

Job Details: 11/01/2023

Installed Sump and motor. ran test op all ok Left leak strip

We serviced a

WHIRLPOOL WALLOVEN

Model WOC75EC0Hs04

Near Colorado Springs, Colorado 80905

Ralph

Job Details: 11/01/2023

"was not the board but a blown tco and wiring, fixed the wiring and repalced the tco, prt cost 63.15...total cost of this repair was 402.73, cust previously paid 384.31, so today cust paid 18.42, unit checked okay"

We serviced a

SUBZERO REFRIGERATOR

Model 590

Near Colorado Springs, Colorado 80907

Ralph

Job Details: 11/01/2023

"installed parts and unit checked okay, cust to monitor"

We serviced a

THERMADOR OVEN

Model PGR364GDZS/01

Near Avon, Colorado 81620

Erik

Job Details: 11/01/2023

test unit: Thermador ALL GAS PROTemp sensor only works on standard bake correctlyBriol ignition failure temp sensor shortBroiler ignition kit 00493265 (DISCONTINUED) NLAneutral break not occuring unless breaker is manually tripped and reconnected (BREAKER RESET)parts required to fix the issue are no longer available and discontinued from the manufacturer SERVICE COMPLETE charge$189.95autho# W4PUU9

We serviced a

WHIRLPOOL WASHER

Model MVWC416FW1

Near Pueblo, Colorado 81001

David

Job Details: 11/01/2023

"Checked washer Motor pully melted, belt broken, spluch pully not smooth They have decided to go with a new machine"

We serviced a

WHIRLPOOL WALLOVEN

Model WOC75EC0HS20

Near Colorado Springs, Colorado 80908

Aaron

Job Details: 11/01/2023

"UI control is resetting periodically, removed and replaced UI control, programmed and tested, working well now. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL M/W OTR

Model WMH32519HZ07

Near Colorado Springs, Colorado 80908

Aaron

Job Details: 11/01/2023

"Removed and replaced transformer, tested unit and heating well now. Advised customer of 5 star survey."

We serviced a

SAMSUNG DISWASHER

Model DW80R2031US/AA

Near Colorado Springs, Colorado 80920

Mathew

Job Details: 11/01/2023

"Found OC error code. Validated serial with tech line, found seal out of place, reattached and test op, unit working as expected. Drain hose was kinked under cabinet causing slow drain, too much water in cabinet. Called hass support about hass compatiblity, they told me it was not."

We serviced a

KITCHENAID WALLOVEN

Model KOCE500ESS08

Near Fountain, Colorado 80817

Carlos

Job Details: 11/01/2023

Installed control board and temp sensor. Ran test op runs ok. Cx paid 209.95 CC Auth. #44XTAN

We serviced a

WOLF OVEN

Model DO3050TE/S/T

Near Colorado Springs, Colorado 80921

Jessie

Job Details: 11/01/2023

Replaced inner door. All ok

We serviced a

MAYTAG DRYER

Model MED4500MW0

Near Colorado Springs, Colorado 80906

Carlos

Job Details: 11/01/2023

Installed leveling feet. All ok

We serviced a

WHIRLPOOL STOVE

Model WFE320M0JS3

Near Colorado Springs, Colorado 80910

Carlos

Job Details: 11/01/2023

Ran test op. No power from wall outlet. Reset circuit breaker. Runs all ok

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ1

Near Colorado Springs, Colorado 80905

Carlos

Job Details: 11/01/2023

Ran test op. Found water supply line was loose. Retighten ran a quick cycle. No leaks found

We serviced a

WHIRLPOOL WASHER

Model MVW7230HW0

Near Pueblo, Colorado 81006

David

Job Details: 11/01/2023

Replaced water valve dispenser and faucet switch Tested and running working good

We serviced a

WHIRLPOOL RANGE

Model WFE505W0HW5

Near Colorado Springs, Colorado 80923

Jerimiah

Job Details: 11/01/2023

Cust using proper water and correct amount. Unit is functioning as designed but still not cleaning as much as expected. Cust will contact whirlpool. Unit check ok.

We serviced a

BOSCH DISHWASHER

Model SHEM63W55N/20

Near Vail, Colorado 81657

Erik

Job Details: 11/01/2023

pulled unit out to styes and remount *see quick picsJOB COMPLETE

We serviced a

MIELE WASHER

Model WXD160

Near Colorado Springs, Colorado 80903

Roman

Job Details: 11/01/2023

"Ran the washer and could not get it to leak, ran a diagnostic cycle and it did not show error codes or leak. Recommend keeping the glass clean for a tight seal. Call us right back if it starts leaking. Paid sc cc $149.95 CC Auth# 9Y99XV"

We serviced a

GENERAL ELECTRIC DISHWASHER - BUI

Model CDT805P2N3S1

Near Pueblo, Colorado 81005

David

Job Details: 11/01/2023

"Checked dishwasher Ran through a cycle The sounds I am hearing seem to be normal The diverter that was put in is working better than the old one, the water pressure to the spray arms is better than before."

We serviced a

AMANA DRYER

Model NED4655EW1

Near Pueblo West, Colorado 81007

David

Job Details: 11/01/2023

Checked dryer Reattached wire to heaterTested and is working good

We serviced a

WOLF RANGE GAS

Model R366

Near Monument, Colorado 80132

Jerimiah

Job Details: 11/01/2023

"Back right burner continually clicking now. Cleaned igniter burner cap head and base, still clicking called techline, says possibly weak igniter. Cust is holding off as not sure if weak igniter is culprit, Cust will live with issue. Labor would be $189.95 upon return service if Cust decides later.814883 igniter $100.40"

We serviced a

SAMSUNG DRYER - ELECTRIC

Model DVE45B6300C/A3

Near Colorado Springs, Colorado 80925

Jeremy

Job Details: 11/01/2023

CX smelled burning during dryer operation. I contacted samsung tech support. Issue is L1 on terminal block was no properly installed and was left loose. This loose connection eventually caused arcing/heat that burnt L1 connection on terminal block (see picture). Samsung denied repair due to improper installation. CX is advised to communicate issue with installation company.

We serviced a

SAMSUNG MICROWAVE

Model ME16A4021AS/AA

Near Colorado Springs, Colorado 80925

Jeremy

Job Details: 11/01/2023

No power to microwave. Main Fuse blown. Replaced fuse and microwave is working. Asked CX to complete the survey.

We serviced a

SAMSUNG REFRIGERATOR

Model RF28T5001SR/AA

Near Colorado Springs, Colorado 80925

Jeremy

Job Details: 11/01/2023

Refridgerator section not cooling. Evap fan not working. Need to replace P-FRE COVER EVAP MODULE. Service Charge $129.95 Labor $209.95 M&P $14.50 Tax $21.78 Total $641.76. CX denied repair. Service Charge $129.95 Auth: X94MLY

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ04

Near Colorado Springs, Colorado 80919

Glenn

Job Details: 11/01/2023

"Install New Evap Motor, UI Control & Main Control. All OPS Test:OK."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ04

Near Colorado Springs, Colorado 80924

Kris

Job Details: 11/01/2023

fc temp@27.0 rc temp@40.0 installed compressor and all parts sent ran test op unit is working to spec at this time.

We serviced a

BOSCH REFRIGERATOR

Model B36CL80SNS/10

Near Colorado Springs, Colorado 80924

Kris

Job Details: 11/01/2023

adjsuted drawer ran test op all ok unit is working to spec at this time.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SEYW00

Near Glenwood Springs, Colorado 81601

James R

Job Details: 11/01/2023

Dropped off icemaker. customer will install..

We serviced a

KITCHENAID DISHWASHER

Model KDTE234GWH0

Near Colorado Springs, Colorado 80919

Carlos

Job Details: 11/01/2023

"Installed water valve. Ran test op, found no leaks, left leak strip."

We serviced a

SUBZERO REFRIGERATOR

Model UC-15IP

Near Colorado Springs, Colorado 80906

Jessie

Job Details: 11/01/2023

Replaced pump and ran clean cycle. All ok

We serviced a

SAMSUNG DRYER

Model DVE45T3400P/A3

Near Colorado Springs, Colorado 80920

Mathew

Job Details: 11/01/2023

Replaced element assy. Test op all okay.

We serviced a

SAMSUNG REFRIGERATOR

Model RF28JBEDBSG/AA 07

Near Colorado Springs, Colorado 80922

Jeremy

Job Details: 11/01/2023

Lots of ice build up. Used all supplied parts. Not HASS compatiable. Ice maker working to the best of my knowledge. Asked cx to complete the survey.

We serviced a

SAMSUNG WASHER

Model WF45R6100AC/US 03

Near Colorado Springs, Colorado 80923

Jeremy

Job Details: 11/01/2023

Diaphragm is ripped and needs to be replacement. Service Charge $129.95 Labor $219.95 M&P $14.50 Part $151.46 Tax $12.42 Total $528.28 CX is going to dicuss cost with spouse. Sertvice Charge $129.95 Auth:3PR3RU

We serviced a

SAMSUNG WASHER

Model WF45T6000AW/A5

Near Colorado Springs, Colorado 80927

Mathew

Job Details: 11/01/2023

"Replace door gasket. Test op, unit working as expected."

We serviced a

SAMSUNG DRYER

Model DVE55A7700V/A3

Near Colorado Springs, Colorado 80917

Jeremy

Job Details: 11/01/2023

Dryer moisture sensor issue. CX complaint is when she would start a normal cycle it would go from starting time and then time would go down and stop pretty quick leaving laundry wet. We put a wet blanket in dryer and witnessed what CX is experiencing. I then contacted tech support and performed sensor test and passed. Tech support said unit is working correctly and customer education was needed. Ran HASS.

We serviced a

BOSCH DISHWASHER

Model SHPM78Z55N/20

Near Monument, Colorado 80132

Kris

Job Details: 11/01/2023

the diswaher was attached and mounted correclty. cx needs installer or cabinet tech to fix issue.

We serviced a

WHIRLPOOL RANGE

Model WFE505W0JS0

Near Colorado Springs, Colorado 80921

Glenn

Job Details: 11/01/2023

Install New Infinite Switch for RF Burner. All OPS Test:OK

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS1

Near Colorado Springs, Colorado 80920

Glenn

Job Details: 11/01/2023

"Install New Sump & Motor Assy. All OPS Test:OK, No Leaks, Installed Leak detector for safety."

We serviced a

FRIGIDAIRE RANGE GAS

Model GCRG3060AFC

Near Colorado Springs, Colorado 80928

Roman

Job Details: 11/01/2023

"Installed new spark module and tested all the burners, all igniting right away. Range working great. Paid $249.95 cc $249.95 CC Auth# X944LH"

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Pueblo West, Colorado 81007

David

Job Details: 11/01/2023

Checked dryer Ck said that there is a rattle when it is first started and the control would freeze and they have to unplug machine and plug it back in to get it to run.Took apart and made sure all screws are tight Replaced control panel If problem with control freezing then it may need the main control board. Tested and is running good at this time.

We serviced a

GE REFRIGERATOR/TOP

Model GZS221YNXHFS

Near Colorado Springs, Colorado 80919

Kris

Job Details: 11/01/2023

adjusted feet. unit is working to spec at this time.

We serviced a

SAMSUNG REFRIGERATOR

Model RF265BEAESR/AA

Near Colorado Springs, Colorado 80915

Mathew

Job Details: 11/01/2023

Replaced all icemaker parts. Test op all okay.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHB08

Near Colorado Springs, Colorado 80918

Glenn

Job Details: 11/01/2023

Rattling noise. Found Condensor fan rubbing on foam cover on coolant line. adjust foam and coolant line. Unit now running normal & quiet.

We serviced a

WHIRLPOOL DISHWASHER

Model WDF540PADM3

Near Cripple Creek, Colorado 80813

Mathew

Job Details: 10/31/2023

"Found bad connection at terminal block. Remastered connection and test op, all okay."

We serviced a

MAYTAG WASHER

Model MVW5430MW0

Near Woodland Park, Colorado 80863

Mathew

Job Details: 10/31/2023

"Replaced valve, test op unit working as expected."

We serviced a

KITCHENAID REFRIGERATOR

Model KBBR306ESS01

Near Santa Fe, New Mexico 87508

Jason

Job Details: 10/31/2023

installed all of the led modules unit checks ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ08

Near Santa Fe, New Mexico 87506

Jason

Job Details: 10/31/2023

installed parts unit opperation checks ok

We serviced a

MAYTAG WASHER

Model MVW5430MW0

Near Santa Fe, New Mexico 87507

Jason

Job Details: 10/31/2023

Installed both controls unit checks ok

We serviced a

WHIRLPOOL COOKTOP

Model WCG55US6HS05

Near Santa Fe, New Mexico 87507

Jason

Job Details: 10/31/2023

Installed parts listed and adjusted simmer heights of burners unit checks ok

We serviced a

WOLF WALL OVEN ELECTR

Model SO30-2F/S

Near Colorado Springs, Colorado 80919

Jerimiah

Job Details: 10/31/2023

"Oven door hold spice cabinet doors in closed position, adjusted oven away from doors, unit check ok"

We serviced a

GENERAL ELECTRIC M/W OTR

Model JVM3160DF8BB

Near Dillon, Colorado 80435

Erik

Job Details: 10/31/2023

install door asm/ test: GOODJOB COMPLETE

We serviced a

GE MICROWAVE

Model JVM6175YK5FS

Near Colorado Springs, Colorado 80919

Ralph

Job Details: 10/31/2023

"unit has a blownb magnatron and tco, will need tobe repalced.....part cost 168.78, cust not repairing but replacing...autho no. F4C444"

We serviced a

JENN-AIR COOKTOP

Model JIC4536XS00

Near Breckenridge, Colorado 80424

Antonio

Job Details: 10/31/2023

Installed new cook top unit looks good unit tested good too

We serviced a

MAYTAG REFRIGERATOR

Model MFI2570FEZ13

Near Colorado Springs, Colorado 80923

Aaron

Job Details: 10/31/2023

"Scratches/dents on FC door and LH RC door, removed and replaced door, no scratches or dents, verified by customer. Advised customer of 5 star survey."

We serviced a

SUBZERO REFRIGERATOR

Model 650HAG

Near Colorado Springs, Colorado 80904

Ralph

Job Details: 10/31/2023

"replaced cond fan motor and door gaskets, unit chekced okay...autho no. AET4V9"

We serviced a

WHIRLPOOL DRYER

Model WED7120HC2

Near Colorado Springs, Colorado 80922

Aaron

Job Details: 10/31/2023

"Excessive moisture is built up in vent hose and wall vent, no bracket on vent hose causing water to leak onto floor, wall duct needs to be professionally cleared, unit's temperatures are good, blower had good push. Advised customer of situation and survey."

We serviced a

WHIRLPOOL RESIDENTIAL REFR

Model WRF954CIHZ00

Near Colorado Springs, Colorado 80924

Aaron

Job Details: 10/31/2023

"Ice maker unable to find home position, filled with ice, tray upside down causing water to freeze in bucket, replaced ice maker, Needs time to cool, customer to monitor. Advised customer of 5 star survey."

We serviced a

BOSCH RANGE

Model HGI8054UC/08

Near Pueblo, Colorado 81003

James

Job Details: 10/31/2023

installed ordered part. tested ops all ckok collected 169.95 $169.95 CC Auth# M33M9M

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ1

Near Woodland Park, Colorado 80863

Mathew

Job Details: 10/31/2023

"Found slow leak due to cap on water vane being loose. Titghtened from inside case and test op, unit working as expected. Left leak strips."

We serviced a

SUBZERO REFRIGERATOR

Model BI-36S/S/TH

Near Colorado Springs, Colorado 80904

Ralph

Job Details: 10/31/2023

pulled and reinstalled drawer

We serviced a

MAYTAG WASHER

Model MVWB835DW4

Near Pueblo, Colorado 81008

James

Job Details: 10/31/2023

installed ordered parts. tested ops all ckok. left litmus

We serviced a

WHIRLPOOL WASHER

Model MVW7230HW1

Near Pueblo West, Colorado 81007

James

Job Details: 10/31/2023

installed slider from previous order tested ops all ckok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT311FZDW02

Near Colorado Springs, Colorado 80919

Carlos

Job Details: 10/31/2023

"installed control board, thermistor and ice maker. Cx will monitor refrigerator"

We serviced a

JENN-AIR WALLOVEN

Model JMW3430DP02

Near Breckenridge, Colorado 80424

Antonio

Job Details: 10/31/2023

Installed new ui panel unit tested good

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC704FPS05

Near Albuquerque, New Mexico 87104

Larry

Job Details: 10/31/2023

Installed parts listed and tested good - Unit is good to go

We serviced a

WHIRLPOOL DRYER

Model WED5100HW3

Near Albuquerque, New Mexico 87104

Larry

Job Details: 10/31/2023

Installed parts listed and tested good - Unit is good to go

We serviced a

MAYTAG WASHER

Model MVWB765FW2

Near Albuquerque, New Mexico 87107

Larry

Job Details: 10/31/2023

"Cx complaint - Washer making loud grinding noise - Inspected unit and found the clutch failed - Replaced with TS and tested good - Unit is good to go - CX is PIF; used 1 W10754448 (Clutch), and 1 W10734521 (Slider) from stock"

We serviced a

JENNAIR RANGE

Model JGRP636HM

Near Breckenridge, Colorado 80424

Antonio

Job Details: 10/31/2023

Installed new lp conversion kit unit could not be tested due to gas being off

We serviced a

MAYTAG WASHER

Model MVWB766FW1

Near Dillon, Colorado 80435

Antonio

Job Details: 10/31/2023

Installed new lid unit tested good

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ08

Near Pueblo West, Colorado 81007

James

Job Details: 10/31/2023

installed preordered parts. tested ops all ckok

We serviced a

GE REFRIGERATOR

Model GSE25GYPFS

Near Pueblo West, Colorado 81007

James

Job Details: 10/31/2023

Installed order parts tested operations all check okay

We serviced a

MAYTAG WASHER

Model MVWX655DW1

Near Pueblo, Colorado 81004

James

Job Details: 10/31/2023

"installed ordered part, tested ops, all ckok"

We serviced a

SAMSUNG REFRIGERATOR

Model RF23M8070SR/AA

Near Pueblo West, Colorado 81007

Brandon

Job Details: 10/31/2023

"Errors 39, 61, 15. Bad auger fan, replaced parts and tested op all ok hass passed"

We serviced a

SAMSUNG REFRIGERATOR

Model RF27T5501SR/AA

Near Pueblo, Colorado 81003

Brandon

Job Details: 10/31/2023

"Error 41c communication error, unrelated to noise issue, Freezer fan making noise hitting ice, cleared all ice, found drain tube clogged with hair, cleared drain tested op all ok hass passed"

We serviced a

SAMSUNG DRYER

Model DVE45B6300C/A3

Near Colorado Springs, Colorado 80916

James S

Job Details: 10/31/2023

"Replaced heater and thermistor. Ran HAAS, unit passed.Tested for proper operation"

We serviced a

SAMSUNG DRYER

Model DVE45T3200W/A3

Near Colorado Springs, Colorado 80919

James S

Job Details: 10/31/2023

Check power for unit. Breakers needed to be rest.Parts not needed.

We serviced a

WOLF MICRO DRAWER

Model MD24TE/S

Near Colorado Springs, Colorado 80906

Ralph

Job Details: 10/31/2023

installed part and unti checked okay

We serviced a

WHIRLPOOL WASHER

Model MVW7230HW0

Near Pueblo, Colorado 81008

David

Job Details: 10/31/2023

"Ck has a extended warranty, but did not go thru Lows. Told them they need to contact Lows and have it dispatched thru Lows to have parts and labor covered with the extended warranty. Service diagnostics fee needs paid, she does not have the money till she gets paid. Amanda will be calling her.Returning parts back to shop till extended warranty comes thru."

We serviced a

BOSCH DISHWASHER

Model SHP878ZD5N/18

Near Colorado Springs, Colorado 80921

Kris

Job Details: 10/31/2023

installed fan and container ran test op all ok. unit is working to spec at this time.

We serviced a

MAYTAG WASHER

Model MHW6630MBK0

Near Peyton, Colorado 80831

Aaron

Job Details: 10/31/2023

"Drain pump shorted out, removed and replaced assembly, tested and working well now. Advised customer of 5 star survey."

We serviced a

WHIRPOOL WASHER

Model CAM2742TQ2

Near Rifle, Colorado 81650

James R

Job Details: 10/31/2023

Test ran unit seems to be working let go thru a cycle all functions ok. Tightened customer paid $149.95 auth code. 99XTA3

We serviced a

WHIRLPOOL RANGE

Model WEC310S0LS2

Near Pueblo, Colorado 81001

David

Job Details: 10/31/2023

Checked range Only one leg of the 240 has power Unable to test due to insufficient power Clock and light inside are working Range is direct wiredNeed electrician to install range outlet

We serviced a

WHIRLPOOL DISHWASHER

Model MDB8959SBS2

Near Peyton, Colorado 80831

Aaron

Job Details: 10/31/2023

"Customer is unable to start a cycle, control light blinks, have proper voltage to control and UI with no response signs of heat on incoming power to control, unable to test the unit further. Needs control, UI control and latch assembly. UI control wpw10475780 $253.60Control w10595568 $275.22Latch assembly w10619006 $69.23Total parts $598.05Tax $49.04Supplies $14.50Hc $129.95Labor $189.95Total job $981.4930 day estimateNo return on partsAuth 129.95 #X33V9P"

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Albuquerque, New Mexico 87121

Larry

Job Details: 10/31/2023

complaint - Long cycle timer - Inspected unit and found ut out of calibration - Calibrated unit and tested good - Unit is good to go

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Colorado Springs, Colorado 80905

Carlos

Job Details: 10/31/2023

"Needs a motor and Transmission, cx will not repair"

We serviced a

JENNAIR REFRIGERATOR

Model JS48SSDUDE00

Near Colorado Springs, Colorado 80906

Carlos

Job Details: 10/31/2023

Ran test op. Refrigerator is cooling at correct temperatures. All ok Cx paid SC $149.95 Auth# WHAF4U

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Colorado Springs, Colorado 80910

Carlos

Job Details: 10/31/2023

"10/23/23 8:47: CR there 23 MON, 8:04 to 8:38, Ran test op. Found Cam teeth are broken and needs a new cam. Replace cam with new one. Cx paid full amount $406.44 CC Auth# W9PMMC; ordrng 1 W10721967 (Cam)"

We serviced a

ZLINE RANGE

Model RA30

Near Colorado Springs, Colorado 80919

Jerimiah

Job Details: 10/31/2023

"Unit taking forever to preheat, verified bake element and inner broil working properly. Cust using high bake properly, checked broil and both elements heat.Replaced thermostat and still no difference. Called techline and with all the repairs, they will have their Cust experience people reach out to cust for resolution. Closing call."

We serviced a

GE RANGE

Model JGBP34GEP3AD

Near Colorado Springs, Colorado 80906

Jerimiah

Job Details: 10/31/2023

"Bake igniter not glowing, needs replacing. Cust holding off. Labor will be $189.95 upon return service $129.95 CC Auth# 34PV9FBake igniter WB2X9154 $171.38"

We serviced a

SAMSUNG DISHWASHER

Model DW80RSB61US

Near Colorado Springs, Colorado 80920

Kris

Job Details: 10/31/2023

ran test op no signs of burning smell unit needs control and heating element.heater dd47-00008a 256.12control board dd82-01337b 283.30

We serviced a

SAMSUNG OTR MICROWAVE

Model ME21M706BAS/AA

Near Pueblo West, Colorado 81007

Jeremy

Job Details: 10/31/2023

Microwave not heating. Bad magnetron/ capacitor. Installed both new parts. Microwave tested good. I asked CX to complete the survey.

We serviced a

FRIGIDAIRE RANGE

Model FCRE305LAFJ

Near Colorado Springs, Colorado 80915

Jerimiah

Job Details: 10/31/2023

"Installed replacement parts. Unit check ok, Cust will keep track of unit functionality."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF757SDHZ02

Near Colorado Springs, Colorado 80920

Kris

Job Details: 10/31/2023

installed compressor charged to 5.25 oz of 134a ran tst op all ok at this time. cx will monitor unit for 24 hours

We serviced a

ASKO DISHWASHER

Model ASK|DFI675XXL|737050

Near Colorado Springs, Colorado 80906

Roman

Job Details: 10/31/2023

Showed up and talked to cx and she had said this was from a year ago. Dw has been working fine since.

We serviced a

BOSCH WALL OVEN

Model HBL5450UC/08

Near Colorado Springs, Colorado 80919

Roman

Job Details: 10/31/2023

Ran the oven to 200 degrees and oven got to that temp and kept getting hotter. Ran diagnostics no error codes came up. Cx said error E115 came up indicating the oven is too hot. Tapped on the relays on the control board and ran the oven again. Temps stayed at where they were set. Recommend replacing the main control boardControl board #12022212 $479.63Tax $39.33Part total $518.96MPs $14.50Labor $289.95Sc $149.95Total cost $973.36

We serviced a

MAYTAG DRYER

Model MDE7658BYW

Near Colorado Springs, Colorado 80921

Glenn

Job Details: 10/31/2023

"Unit not starting, just hums when attempt to start. Bad Motor , Motor - WP33002795 $299.42 , Tax $24.55 , MPS $14.50 , Labor $219.95 , Customer Declined Estimate. Paid SC fee of $129.99 Via Chk #1693 ,(Customer wrote check for 129.99) Autho# RCPV9Y"

We serviced a

BOSCH DISHWASHER

Model SHP65TL5UC/07

Near Colorado Springs, Colorado 80904

Roman

Job Details: 10/31/2023

Ran the dw and it it sounded like there was a gap in between the door and tub. Door also crooked. Right side had 2 screws and both coming out and keeping the door from closing properly causing it to leak in the upper right side. Removed the screws and installed one properly and door shuts properly. Have a feeling that was whats causing it to run past its cycle as-well. Recommend to cx keeping filters clean. Sc $149.95Labor $50.00Total cost $199.95 paid gc

Our Service

Our Company