We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM00
Near Santa Fe, NM 87507
Jason
Job Details:
12/12/2023
checked unit temps check ok ice bin is full. no signs of unit not cooling. unit opperating as designed at this time
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW2
Near Rio Rancho, NM 87144
Larry
Job Details:
12/12/2023
Installed suspension and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ03
Near Santa Fe, NM 87507
Jason
Job Details:
12/12/2023
could not verify cx complaint at this time unit is opperating as designed
We serviced a
MAYTAG DRYER
Model MGD4500MW1
Near Santa Fe, NM 87508
Jason
Job Details:
12/12/2023
installed parts unit checks ok
We serviced a
KITCHENAID RANGE
Model KDRP463LSS05
Near Corrales, NM 87048
Larry
Job Details:
12/12/2023
During repair I found there was a large presence of mice inside the unit - The main control is covered with mouse urine and feces and I also found chewed wires - The main control is NLA - Called techline and was disconnected after 37min
We serviced a
MAYTAG RANGE
Model MER8800FZ
Near Frisco, CO 80443
Antonio
Job Details:
12/12/2023
Found loose connection at wire block tightened unit tested good
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Colorado Springs, CO 80920
Roman
Job Details:
12/12/2023
Checked freezer temps and it was getting a reading of about 1 to 12 degrees with doors being opened and closed. Checked the gasket and it is okay. Evaporator has good frost built up on it and fan is running. Called tech support and they had said that the fridge is not meant to be in 55 degree or colder place like the cx garage which is where it is. Freezer also has nothing in it and freezer is meant to have stuff in it to keep the temperatures from fluctuating a lot. Recommended to cx to fill ot with water jugs and and smaller waters in the door to see if things freeze and fridge stays at temps. Also recommend getting a temp gage. If cx calls back recommend coming back with a temperature thermostatTemp thermostat #WPW10384183 File #7738001432
We serviced a
BOSCH M/W OTR
Model HMV8053U
Near Colorado Springs, CO 80918
Kris
Job Details:
12/11/2023
installed door switches and fuse ran test op all ok at this time.
We serviced a
MAYTAG DRYER
Model MED6630HC0
Near Rio Rancho, NM 87124
Larry
Job Details:
12/11/2023
"CX complaint - Dryer not heating - Inspected unit and found the element failed and the rollers are squeeling - Installed new element and roller kit from TS and tested good - Unit is good to go - CX is PIF; used 1 WP3387747 (Element (Front Blower)), and 1 4392067 (Dryer Kit (4 Roller)) from stock"
We serviced a
AMANA WASHER
Model WTW4816FW3
Near Rio Rancho, NM 87144
Larry
Job Details:
12/11/2023
CX complaint - Squeeling noise - Inspected unit and found the splutch failed - Replqced with TS and tested good - Unit is good to go; used 1 W10721967 (Cam) from stock
We serviced a
WHIRLPOOL MICROWAVE
Model WMH78019HW06
Near Rio Rancho, NM 87144
Larry
Job Details:
12/11/2023
CX complaint - MW sparked inside - Inspected unit and found the Wave Guide Cover has excessive grease on it that burned a bit when in use - Removed cover to inspect wave guide and checks good - Unit is operating as designed - Advised cx to clean unit periodically.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Corrales, NM 87048
Larry
Job Details:
12/11/2023
Installed hinges and tested good - Unit is good to go
We serviced a
ASKO DISHWASHER
Model n/a
Near Colorado Springs, CO 80919
Ralph
Job Details:
12/11/2023
"unit was stuck in cycle, cleared the setting then unpluggedtoreset the board, and unit started washing, unit checked okay...autho no.9F44KH"
We serviced a
WHIRLPOOL RANGE
Model WFE535S0LZ2
Near Colorado Springs, CO 80923
Aaron
Job Details:
12/11/2023
"Tested unit at 350f with +30 calibration, average temperature 352, working well now,advised customer of usage and survey."
We serviced a
SAMSUNG DISHWASHER
Model DW80R7060US/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
12/11/2023
"Replaced support string and tested op all checks ok hass passed, called techline and documented"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Colorado Springs, CO 80911
Carlos
Job Details:
12/11/2023
Installed gasket and switch cx will observe .
We serviced a
SAMSUNG DISHWASHER
Model DW80B7070US/AA
Near Monument, CO 80132
Brandon
Job Details:
12/11/2023
"Error 5c1, drain getting voltage, found debris in drain pump, removed debris and tested op all checks ok hass passed"
We serviced a
BOSCH WASHER
Model WAW285H2UC/20
Near Aspen, CO 81611
Erik
Job Details:
12/11/2023
install doorjob complete
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMELBSR/AA
Near Pueblo, CO 81001
Joseph
Job Details:
12/11/2023
"I was able to confirm issue I found the unit has a frosting over icemaker, I replaced all parts in units service buliten job complete"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA
Near Pueblo, CO 81005
Joseph
Job Details:
12/11/2023
"I was able to confirm issue, I found that the unit will need a new icemaker because the icemaker is not producing Ice.replaced icemaker and tested unit job complete"
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Pueblo West, CO 81007
James
Job Details:
12/11/2023
"found bottom of oven cavity warped causing it to not stay in place. replaced with preordered part. tested ops, all ckok"
We serviced a
SAMSUNG WASHER
Model WF45A6400AV
Near Pueblo, CO 81005
James
Job Details:
12/11/2023
installed ordered part tested ops. ui now responds as designed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SNHM06
Near Colorado Springs, CO 80921
Kris
Job Details:
12/11/2023
unit is in garage showed cx unit needs to be above 55 degrees per cx hand book page 7.
We serviced a
FRIGIDAIRE WALLOVEN
Model FGET2745KFA
Near Colorado Springs, CO 80923
Kris
Job Details:
12/11/2023
installed element ran test op all ok at this time
We serviced a
BLUESTAR RANGE
Model RNB486GSS
Near Colorado Springs, CO 80923
Kris
Job Details:
12/11/2023
installed ignitor ran test op all ok at this time.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Peyton, CO 80831
Aaron
Job Details:
12/11/2023
"F1E2 motor control error code upon arrival, outlet has good polarity, 123.8v to control, corrected connection at stator harness, checked slider, tested through diagnostics three times, working well and no further error codes. Discussed with techline. SR7737999012"
We serviced a
SAMSUNG DRYER
Model DVG52A550
Near Colorado Springs, CO 80938
Mathew
Job Details:
12/11/2023
"Found hc error on test. Cleared vent and test again, hc error still there. Test thermoster found broken wire leading to thermistor. Repaired and test op all okay."
We serviced a
GE OVEN
Model JBP24W0K4WW
Near Colorado Springs, CO 80907
Ralph
Job Details:
12/11/2023
installed partand unit checked okay
We serviced a
SAMSUNG REFRIGERATOR BOT
Model RF28R7351SRI
Near Colorado Springs, CO 80922
Mathew
Job Details:
12/11/2023
"C6 c47 c13 found multiple issues, ice room door operating non stop. Will need switches and motor, assy is not available. Unit may also need control $398.90 DA94-04603A. Svf $129.953405-001117 x2 $48.74 ea. $97.48 +$7.99DA31-00079D $150.68 + tax $12.36MPs $14.50 $412.96Labor $219.95 Cx holding off for now on repair. 129.95 paid today. $142.95 CC Auth# KLPA9L"
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9671SR/AA
Near Colorado Springs, CO 80920
Mathew
Job Details:
12/11/2023
"Fixed connection on reed switch, unit now working as expected."
We serviced a
GE DRYER
Model GTD75ECSL0WS
Near Colorado Springs, CO 80915
Roman
Job Details:
12/11/2023
"Ran the dryer and it squealing, took the dryer aprt and the and the front bearing is down to metal. Recommend replacing the front bearing assyFront bearing assy #WE03X23875 $149.42Tax $12.25Total parts $161.67MPs $14.50Labor $189.95Sc $129.95Total cost $496.07Paid sc $129.95 CC Auth# N39YAX"
We serviced a
GE RANGE
Model CES700P3M1D1
Near Colorado Springs, CO 80919
Roman
Job Details:
12/11/2023
"Ran the oven at 350 degrees and oven gets to about 230 degrees and baking shuts off, everything else stays on. Checked all the heating elements and cooling fan it its getting volts and running. Checked the fault codes and they are indicating a cooling fan fault, or the touchpad is wearing out. Checked the rpms on the fan and its running at around 1500 rpms which is normal. Ran the oven after unplugging it and it worked fine and got it up to 450 degrees without it shutting down. Called tech support and they did not recommend replacing parts yet till the errors come up again, because it could have just reset the control board/ panel. Cooling fan #WB26X32571 $179.94Control panel #WB27X31746 $458.82Tax $MPs $14.50Labor $249.95Sc $129.95Paid sc $149.44 CC Auth# C9E4AC"
We serviced a
THERMADOR FREEZER
Model T30IF905SP/21
Near Colorado Springs, CO 80920
Ralph
Job Details:
12/11/2023
installed part and unit checked okay
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Colorado Springs, CO 80915
Carlos
Job Details:
12/11/2023
Installed sump assembly
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS1
Near Colorado Springs, CO 80903
Carlos
Job Details:
12/11/2023
Installed tracks and supports all ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Colorado Springs, CO 80904
Carlos
Job Details:
12/11/2023
"Installed sump assembly, drain pump and control board. Advised cx to have an electrician check wall outlet for dishwasher"
We serviced a
GE RANGE
Model CTD90DP3N2D1
Near Colorado Springs, CO 80906
David
Job Details:
12/11/2023
Replaced control boards Tested and is working great
We serviced a
WHIRLPOOL DRYER
Model WED7120HW0
Near Colorado Springs, CO 80910
Carlos
Job Details:
12/11/2023
Ran test op. Door was crooked readjusted door. Recommend cx have vents clean and hose shorten.
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDF630PSM3SS
Near Peyton, CO 80831
Aaron
Job Details:
12/11/2023
"Unit is intermittently not powering on at the user interface, working well at time of inspection, upon further inspection found the main control board has signs of smoking/ burning, correct polarity to the unit and sending 13v DC to the UI control, informed customer of the burning. Estimate is for the control, and customer understands that other components could have been effected. Heating element and thermostat check out okay, unit working well at time of inspection. Control WD21X32165 $168.78Tax $13.84Supplies $14.50Hc $129.95Labor $189.95Total job $517.0230 day estimate No return on parts Auth $129.95 hc #H44U43"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Grand Junction, CO 81507
James R
Job Details:
12/11/2023
When I arrived sensing light flashing. Would not start.Unplugged to reset unit. Put into service diagnostics. No error codes. Unit went thru no issues. If water level is set to low for load items in unit can get out of balance and load may not spin out properly. Adjust load and restart. Checked water level auto sensing and deep water are working. Showed customer. Unit is working as should. Do here rattling no adjust rear panel per TSP W11695259 adjust rear panel to eleviate rattling sound in panel. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SAMSUNG RANGE
Model NE63A6511SS/AA
Near Colorado Springs, CO 80920
Mathew
Job Details:
12/11/2023
Replaced board and upper assy. Test op all okay.
We serviced a
KITCHENAID VENT HOODS
Model KVIB606DSS4
Near Grand Junction, CO 81507
James R
Job Details:
12/11/2023
Pin that goes in connector wasnt straight had to straighten so would connect properly. Right rear light replaced. Test operation it is normal. Working as should. Please fill out whirlpool tech satisfaction survey. Thank You. Customer pais labor $99.95 auth code. FEEL3F
We serviced a
GE REFRIGERATOR
Model GTS17GSNKRSS
Near Colorado Springs, CO 80910
Roman
Job Details:
12/11/2023
Removed the old damaged door and installed new doorZ made sure gasket ones up and door closes properly. Fridge working great.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SR/AA
Near Colorado Springs, CO 80918
Mathew
Job Details:
12/11/2023
Replaced all parts. Completed icemaker service bulletin.
We serviced a
WHIRLPOOL WASHER
Model WFW9300VU02
Near Colorado Springs, CO 80918
Glenn
Job Details:
12/11/2023
"making a loud sound during the spin cycle/ loud clatterUnit Has Bad Bearing / Spider Gear. Requires New Rear Tub Assy, Seal & Basket. Customer Declined Estimate.Paid SC Fee $129.95 , Autho# U4RANK"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BW2
Near Grand Junction, CO 81501
James R
Job Details:
12/11/2023
Signed disclaimer.Put into diagnostics. No error codes present. Slid unit out and checked sensor probe connection and at control. Did a bake cycle. Set to 350 degrees. Let cycle several times. Did not come up with any errors. Unit is operating as it should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Colorado Springs, CO 80918
Glenn
Job Details:
12/11/2023
"Reseat connections, All OPS Test:OK"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Grand Junction, CO 81504
James R
Job Details:
12/11/2023
Customer signede waiver. Put into service diagnostics F0E5 error off balanced load. Cleared code. If load is unbalanced enough unit will not finish cycle. Customer needs to stop cycle adjust load then restart. Checked diagnostics cycle. Unit did not shift properly. Replaced slider and clutch checked again operating as should. Did a DLMS calibration cycle. Also a unbalanced load detection cycle. All normal.
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS3
Near Colorado Springs, CO 80909
David
Job Details:
12/11/2023
Ignitor burned-out Replaced Ignitor Working good
We serviced a
WHIRLPOOL DRYER
Model MEDB835DC4
Near Colorado Springs, CO 80921
Glenn
Job Details:
12/11/2023
"Pre-Paid for part 4392067 $75.90, tax $6.22,total $82.12.Paid Labor $199.95 , MPS $14.50 = $214.45 + Tip $21.45 = $235.90 , Autho# F34VE4"
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ3
Near Peyton, CO 80831
Aaron
Job Details:
12/11/2023
"Tested unit at 350f, 30 minutes after preheat was completed exterior temperature on the left was 147f and 115 for the right, discussed with techline once more and reported findings, unit deemed working as designed and temperatures are withing limits. Advised customer of situation and survey. SR7737926275"
We serviced a
MAYTAG WASHER
Model MVW6230RHW2
Near Colorado Springs, CO 80924
Aaron
Job Details:
12/11/2023
"Removed and replaced lower harness and pump, tested unit though DLMS and diagnostic cycles, working well now. Advised customer of 5 star survey."
We serviced a
JENN-AIR DISHWASHER
Model JDPSS244LL2
Near Colorado Springs, CO 80921
Glenn
Job Details:
12/11/2023
"New Home, Door Unlocked. Need a good contact for who to call regarding the service on this property. VM for current contact appears to be old, and message indicates they are on Vacation until August? No Sump & Motor Assy? Called Tabitha to have her follow up on the above. F7E1 ERROR - Single Speed Wash Motor Failure. Tabitha was able to reach super, said part was in Master Closet. Install New Sump & Motor assy, All OPS Test:OK, No Leaks, Installed Leak Detector for safety. No One onsite to sign."
We serviced a
SUBZERO REFRIGERATOR
Model 650/F
Near Colorado Springs, CO 80904
Ralph
Job Details:
12/11/2023
installedlisted parts and unit checked okay
We serviced a
WOLF RANGE
Model DF364G
Near Monument, CO 80132
Kris
Job Details:
12/11/2023
installed board ran test op all ok at this time.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, CO 80921
Glenn
Job Details:
12/11/2023
"Install New Support Shafts & Repair Kit, All OPS Test:OKUnit is now running quietly as it should."
We serviced a
MAYTAG WASHER
Model MHW5100DW0
Near Colorado Springs, CO 80919
Glenn
Job Details:
12/11/2023
"Unit did not complete cycle, Errors:F9E1 > LONG DRAINF3E1 > WATER LEVEL SYSTEM ERROR , Bad Drain Pump Assy & Pressure Switch (Possible Bad Main PCB as well) , Pressure Switch - WPW10448876 $83.80 , Drain Pump - WPW10605427 $90.72 , ACU - W11029844 $294.91 , Tax $38.49 , MPS $14.50 , Labor $199.95 , Declined Estimate, Paid SC Fee of $129.95 Cell Used for payment: 937-765-6945 , Autho# 33M4C3"
We serviced a
SAMSUNG GAS RANGE
Model NX58H5600SS/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
12/11/2023
"Bad bake hsi, tested and troubleshooted with techline. Cx calling office to make payment. Dg94-00520a $271.58, Labor $189.95, Svf $129.95, Mps $14.50, Tax $22.27"
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Colorado Springs, CO 80908
Brandon
Job Details:
12/11/2023
"Error dc1, door is not locking, can hear clicking from main board, replaced PCB kit and tested op all checks ok hass passed"
We serviced a
SAMSUNG GAS RANGE
Model NX60T8711SS/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
12/11/2023
"Delivery damage, straightened as best as possible, drawer is staying closed now, hass failed, hass support said to override"
We serviced a
SUB ZERO REFRIGERATOR
Model 700TR2
Near Colorado Springs, CO 80905
Ralph
Job Details:
12/11/2023
"remedied the leak, and cleaned cond....autho no. YNVA3F"
We serviced a
MAYTAG WASHER
Model MVW7230HW
Near Colorado Springs, CO 80918
Mathew
Job Details:
12/11/2023
"Replaced motor, spider and clutch. Test op, unit working as expected."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ00
Near Colorado Springs, CO 80924
Jessie
Job Details:
12/11/2023
Replaced listed parts. Charged unit 134a. All ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Grand Junction, CO 81504
James R
Job Details:
12/11/2023
Put into service diagnostics. No error codes. Tilted back Found cover over pulley hanging loose. Reinstalled correctly. Test thru several cycles all checked ok. Lid locks abit later so customer can add cloths if needed at first. Then locks before spin cycle begins as it should. No issues unit is operating as should. Customer signed waiver. Please fill out whirlpool tech satisfaction survey.
We serviced a
SAMSUNG REFRIGERATOR
Model RF22R7351SR/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
12/11/2023
Replaced parts and cycled ice maker all checks ok hass passed
We serviced a
SUBZERO REFRIGERATOR
Model 650/0
Near Colorado Springs, CO 80906
Ralph
Job Details:
12/11/2023
installed listed parts and unit cdhecked okay
We serviced a
SAMSUNG WASHER
Model WF45R6100AWUS
Near Pueblo, CO 81003
James
Job Details:
12/11/2023
installed ordered parts leveled unit and tested ops all ckok.
We serviced a
HOTPOINT DRYER
Model NVLR333EV0WW
Near Pueblo, CO 81005
James
Job Details:
12/11/2023
installed ordered parts all ops test good
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Albuquerque, NM 87116
Jason
Job Details:
12/11/2023
installed compressor unit checks ok
We serviced a
WHIRLPOOL WASHER
Model LSQ9549LW0
Near Pueblo, CO 81005
James
Job Details:
12/11/2023
found loose hose at fill valve. secured and tested all ops test good. no leaks found
We serviced a
BOSCH REFRIGERATOR
Model B36CD50SNS/03
Near Carbondale, CO 81623
Erik
Job Details:
12/11/2023
install: collect $75 deductableJOB COMPLETEautho# P4LW94
We serviced a
MAYTAG DRYER
Model MGD4500MW1
Near Albuquerque, NM 87123
Jason
Job Details:
12/08/2023
checked unit found loose timer connection re seated plug unit checks ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS02
Near Colorado Springs, CO 80927
Aaron
Job Details:
12/08/2023
"Evaporator fan is not pulling cold air effectively, removed and replaced housing, tested and working well, needs time to cool back down. Advised customer of survey."
We serviced a
AMANA DRYER
Model NED4655EW1
Near Pueblo, CO 81001
David
Job Details:
12/08/2023
Installed maintenance kit Running and sounding like it should
We serviced a
MAYTAG DRYER ELECTRIC
Model MEDB835DW4
Near Colorado Springs, CO 80915
Carlos
Job Details:
12/08/2023
Cx has F4E3 Code indicating air flow restriction. Cx needs to have vents cleaned. Cx paid SC $129.95 CC Auth# 9T4T4J
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ
Near Colorado Springs, CO 80925
Roman
Job Details:
12/08/2023
Removed the old door and installed new door. Made sure water and touchpad are working. Fridge working great.
We serviced a
WOLF RANGE
Model DF366
Near Colorado Springs, CO 80904
Roman
Job Details:
12/08/2023
"Called tech support and they said the black trim between the stainless and stove top does not come with the range, cx had a picture of the trim at the store they bought it from had it. Recommended to cx to call the store and see if they had added the trim or the range should have came with it."
We serviced a
GE REFRIGERATOR
Model GFE28GYNJFS
Near Pueblo, CO 81001
David
Job Details:
12/08/2023
Replaced pcb assembly and cap touch panel (UI)Tested and is working great
We serviced a
SPEEDQUEEN WASHER
Model ATE50FGP171TW01
Near Colorado Springs, CO 80904
Roman
Job Details:
12/08/2023
Ran the washer on a spin cycle and it spins and drains. Checked the drain pump filter and it is clear. The control board is the issue and probably a relay on it not advancing. Recommended to cx try running different cycles and see if it will advance. Otherwise recommend replacing the control board. Control board #803254P $1131.59Paid sc check #5622 $129.00 CK Auth# 9WULHT
We serviced a
BOSCH DISHWASHER
Model SHPM78Z55N/22
Near Colorado Springs, CO 80919
Ralph
Job Details:
12/08/2023
instlled part and cust approved rewpair
We serviced a
SCOTSMAN ICE MACHINE
Model DCE33PA
Near Colorado Springs, CO 80906
Ralph
Job Details:
12/08/2023
reinstalled ice mkr and unit checked okay
We serviced a
BOSCH REFRIGERATOR
Model B36CT80SNS/08
Near Avon, CO 81620
Erik
Job Details:
12/08/2023
installedJOB COMPLETE
We serviced a
WHIRLPOOL WALL OVEN
Model WOC75EC0HS03
Near Colorado Springs, CO 80905
Carlos
Job Details:
12/08/2023
Installed control board. Ran test op all ok. Cx paid $209.95 CC Auth# U39C43
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Manitou Springs, CO 80829
Carlos
Job Details:
12/08/2023
Installed timer and switch. Ran test op all ok
We serviced a
THERMADOR REFRIGERATOR BOT
Model T36BB810SS/02
Near Colorado Springs, CO 80921
Kris
Job Details:
12/08/2023
installed fan ran test op all ok at this time.
We serviced a
ELECTROLUX DRYER
Model ELFE7637AT0
Near Colorado Springs, CO 80904
Roman
Job Details:
12/08/2023
"Ran the dryer and it is making a slight vibrating noise. Pulled the unit out and checked support wheels, pulley, and tightened all screws. Only thing I noticed was detergent built up on the blower wheel, cleaned the wheel off and put dryer back together. Tested it and it did not make the noise. Let cx know to watch it and make sure to not use too much detergent so it wont get stuck inside the blower wheel."
We serviced a
SAMSUNG REFRIGERATOR
Model RF260BEAEBC/AA 02
Near Colorado Springs, CO 80919
Roman
Job Details:
12/08/2023
Held the reset filter buttons and filter light turned off. Showed cx how to turn it off in the future. Paid sc
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ08
Near Colorado Springs, CO 80920
Glenn
Job Details:
12/08/2023
"Install New Evap Motor, Shroud, Blade, Grille, Foam & Frzr Door. All OPS Test:OK, Fan running nice & quiet at this time."
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB660012AA
Near Colorado Springs, CO 80927
Brandon
Job Details:
12/08/2023
"Replaced ice bit ice maker and cycled all checks ok, hass passed"
We serviced a
SAMSUNG DRYER
Model DV42H5200EF/A3
Near Colorado Springs, CO 80919
Roman
Job Details:
12/08/2023
"Ran the dryer and it squeaking really loud. Took the dryer apart and the idler pulley is sticking. Pulley is not damaged, Tried cleaning the axle, recommend replacing the idler pulley. Idler pulley #DC93-00634A $97.56Tax $8.00Parts total $105.56MPs $14.50Labor $139.95Sc $129.95Total cost $389.96Paid sc $219.90 CC Auth# 4EAM99"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSR/AA 06
Near Colorado Springs, CO 80920
Mathew
Job Details:
12/08/2023
Installed parts and completed service bulletin. Test op all okay. Unit working as expected. Not hass compatible
We serviced a
BEKO WALL OVEN
Model WOS30200SS
Near Colorado Springs, CO 80921
Kris
Job Details:
12/08/2023
installed door glass. all ok at this time.
We serviced a
WHIRLPOOL DRYER
Model MED6230HC3
Near Colorado Springs, CO 80908
Aaron
Job Details:
12/08/2023
"Removed and replaced blower and motor, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM06
Near Colorado Springs, CO 80922
Aaron
Job Details:
12/08/2023
"Dents on both lower doors, removed and replaced doors, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
SUBZERO REFRIGERATOR
Model IC-30FI-LH
Near Colorado Springs, CO 80908
Kris
Job Details:
12/08/2023
cx is paying sc. ran test op unit has bad ice maker will not cycle. unit may have bad valve will not know until im is installed. 7002740 318.50
We serviced a
BOSCH RANGE
Model HIS8655U/04
Near Avon, CO 81620
Erik
Job Details:
12/08/2023
install/test: FAILbreaker tripsUNIT UNREPAIABLE - REPLACED ENTIRE COOKTOP COMPONENT LISTcall BSH TAG - CASE#4103920299CX call 1800-944-2904
We serviced a
BOSCH DISHWASHER
Model SHP65T55UC/07
Near Colorado Springs, CO 80906
Ralph
Job Details:
12/08/2023
installed drain pump cust happy...autho no. YC9CX9
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Edwards, CO 81632
Erik
Job Details:
12/08/2023
miswired *see quick pics
We serviced a
WHIRLPOOL DRYER
Model WED5100HW2
Near Colorado Springs, CO 80917
Aaron
Job Details:
12/08/2023
"Moisture sensors are not properly responding to control board,removed and replaced sensors, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
THERMADOR RANGE
Model PRD486WDGU/06
Near Edwards, CO 81632
Erik
Job Details:
12/08/2023
miswired *see quick pics