We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
06/18/2026
"INSTALLED PART, AND UNIT CHECKDED OKAY"
We serviced a
SUBZERO FREEZER
Model 201FD
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
06/18/2026
REPLACED LISTED PART AND UNIT CHECKED OKAY
We serviced a
SUB ZERO BEVERAGE CENTER
Model 245
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
06/18/2026
REPLACED LISTED PART AND UNIT CHECKED OKAY
We serviced a
JENNAIR REFRIGERATOR
Model JFI2089AES0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
06/18/2026
Unthawed Ice built up runs all ok cx paid SC $169.95 CC Auth# 99WXF9
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3336SZ00
Near Albuquerque, New Mexico 87120
Larry
Job Details:
06/18/2026
CX complaint - Left door squeaks when opening it - Inspected unit and found the hinge unlubricated - Applied silicone and tested good - Unit is good to go - Survey mentioned
We serviced a
ELECTROLUX DRYER
Model ELFE7637AT1
Near White City, Oregon 97503
Kyle
Job Details:
06/17/2026
"Replaced all 4 rollers, shafts and spacers. Tested unit. Unit is operating as intended. No noise present during cycle."
We serviced a
THERMADOR REFRIGERATOR
Model T24UR925RS/01
Near Dayton, Oregon 97114
Jesse
Job Details:
06/17/2026
(JG) 8:11 am June 17th called eta 10amVerified dented kick plate and door. Replaced. Tested. Had client inspect work
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Sheridan, Oregon 97378
Austin
Job Details:
06/17/2026
6/17/26 BA: removed and replace air damper control in freezer compartment. Tech let the unit run for approximately 15 minutes to check frost patterns and air flow.
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Williams, Oregon 97544
Chris
Job Details:
06/17/2026
"Found rotor bolt loose. After tightening it I did a factory reset, 2 calibration tests and factory diagnostic test. No error codes. Washer is working normally."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZO5
Near Palisade, Colorado 81526
James R
Job Details:
06/17/2026
Signed disclaimer. Replaced evap fan motor and R.H. F.F. door switch. Is working as designed. Customer paid labor $239.95 auth code. 34MPER Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ4
Near Vail, Colorado 81657
Antonio
Job Details:
06/17/2026
"Found unit not draining due to knockout, not being knocked out on disposal, so I removed it unit is testing good."
We serviced a
SUB ZERO REFRIGERATOR
Model 695/F3
Near Bend, Oregon 97707
Levi
Job Details:
06/17/2026
"Unit was flashing ec40 error and that is saying that freezer compressor runtime is too high. Temps in freezer and FF sections are good, condenser is clean. All 3 fans are running. After resetting power, unit went into defrost and that was running fine. I could not determine main cause of error at this time though I'm leaning towards a failing compressor on the freezer side.If unit doesn't improve over the next few days then I recommend a new freezer compressor and filter drier."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323ASD
Near Cripple Creek, Colorado 80813
Charles
Job Details:
06/17/2026
"Freezing items in fridge, damper working, temp 38, advised on location and blocking of thermostat, not to block gap at back of shelves. Adjusted doors to level."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
06/17/2026
"Cx needs to ensure loads are balanced, cx was running heavy load on Delicate wash, has lower spin rpm"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3136SZ00
Near Florissant, Colorado 80816
David
Job Details:
06/17/2026
"Replaced icemaker, ran several cycles, icemaker running and filling as designed."
We serviced a
WHIRLPOOL DISHWASHER
Model WDF310PAAB1
Near Divide, Colorado 80814
David
Job Details:
06/17/2026
"Installed latch components and control, ran diagnostics cycle and a short cycle. Running normal."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Cedaredge, Colorado 81413
James R
Job Details:
06/17/2026
Signed disclaimer. Put into service test and error codes has a F7E4 error basket re-engagement failure. Removed the mtr stator found the slider faulty. Metal ring had slipped down so wouldnt re-engage. Replace slider and stator. re- installed rotor. Put into service test did a DLMS calibration and then put thru a auto service test went thru no issues. Unit is working as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
KITCHENAID DISHWASHER
Model KDPS324SPS01
Near Grand Junction, Colorado 81506
Clint
Job Details:
06/17/2026
"Customer signed disclaimer and recieved parts ordered. Installed new fuse and wiring unit lit up and filled,drained perfectly PLEASE TAKE TECH SURVEY THANKS.CLINT"
We serviced a
SAMSUNG RANGE
Model NX60A6751SS/AA
Near Pueblo, Colorado 81001
Mathew
Job Details:
06/17/2026
Install parts. Test op. All okay.
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EHL04
Near Bend, Oregon 97707
Levi
Job Details:
06/17/2026
"Replaced ice maker, tested, all checks okay. Through diagnostics, I could only get the water valve to spit for about a quarter of a second. But the ice maker seems to be functioning."
We serviced a
GE REFRIGERATOR
Model GFE28GYNJFS
Near Merlin, Oregon 97532
Chris
Job Details:
06/17/2026
"Replaced the evaporator and filter drier. Pressure tested for leaks. Pressure held, I recharged the system and waited for the Pressures to normalize. I found the beginning of a frost pattern."
We serviced a
KITCHENAID WALL OVEN
Model KOCE500ESS11
Near Florissant, Colorado 80816
Charles
Job Details:
06/17/2026
"Melted wire nuts in junction box, aluminum to copper wires, did not use correct wire nuts or no-loc at connection. Reconnected temporary to test oven and microwave all functions working or appear to be working at this time. Customer is still not confident unit is working properly"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FPRU19F8WF3
Near Terrebonne, Oregon 97760
Richard
Job Details:
06/17/2026
Installed new evaporator fan and leveling leg cycle tested unit all checks. Good at this time job complete.
We serviced a
WHIRLPOOL ICE MACHINE
Model WUI75X15HZ01
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
06/17/2026
"REPLACED CUST DRAIN PUMP THAT HE PURCHASED, UNIT CHECKED OKAY"
We serviced a
FRIGIDAIRE STACK UNIT
Model FLCG7522AW4
Near Madras, Oregon 97741
Richard
Job Details:
06/17/2026
Tested unit found no error codes speaking with tech-support water levels are designed by the manufacture engineers I cannot be changed file number for repair 1007552261.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87108
Jason
Job Details:
06/17/2026
Installed control. ran calibration cycle and quick wash. unit operation checks ok. spoke to cx about review
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB86004MAA
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
06/17/2026
"replaced compressor and drier, held vaccum and charged unit tested operation all checks ok hass passed"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFHT1425VV05
Near Powell Butte, Oregon 97753
Richard
Job Details:
06/17/2026
Installed new light module cycle tested unit all tested good at this time. Job complete.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Powell Butte, Oregon 97753
Richard
Job Details:
06/17/2026
"Cycle tested unit thru diagnostics found ice maker working fine at this point,customer wants to se if unit will continue to work if not he will call back ,customer paid service fee by CC of $149.95 (auth# M9YMMP, TRAN# 4209947 ) if customer calls back ship part to RS"
We serviced a
BOSCH DISHWASHER
Model SHS5AVF6UC/22
Near Salem, Oregon 97305
Jesse
Job Details:
06/17/2026
"Client states dw leak is intermittent but has destroyed base board below sink. Findings: at this time I cannot replicate leak. Concerns : active ant infestation on unit.Extreme galvanic corrosion on left side unit by fill components including door tension springs. Water fill components have oily residue build up within. Hinges are also affected by corrosion. Unit was improperly installed, screws were driven through side flaps into cabinets. Counter top is stone , client does have a bracket between unit and counter but there are no mounting brackets or screws securing unit to counter bracket , unit wobbles also causing miss alignment of door."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
06/17/2026
Arrived and cx complaint of noisy. Gound failed idler pulley. Replaced ifkrr belt and rollers. Unit is functioning now as designed. Informed cx of review.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
06/17/2026
Arrived and cx complaint of found part in washer. I could not identify part. Not part of washer that I could identify. Tested washer unit is functioning as designed.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302EBS09
Near Bend, Oregon 97707
Levi
Job Details:
06/17/2026
"Replaced both refrigerator door seals, all checks okay. It only shows one of those ordered by us but both of them that shipped from marcone."
We serviced a
WOLF COOKTOP
Model CT36I/S
Near Woodland Park, Colorado 80863
Charles
Job Details:
06/17/2026
"E9 on left two induction elements, generator board no longer available. Service fee $189.95 paid autho 9N9PHK"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS05
Near Woodland Park, Colorado 80863
Charles
Job Details:
06/17/2026
"Unable to verify complaint of noise, said it sounds like gurgling noise every 15 minutes, possibly refrigerant equalizing in seal system"
We serviced a
WHIRLPOOL RANGE
Model WFES3030RS0
Near Carlton, Oregon 97111
Austin
Job Details:
06/17/2026
6/16/26 BA: removed and replaced oven door hinges with new. Tested oven functions and found no further issues. Service complete
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPA02
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
06/17/2026
"After reset machine is full of ice, replaced cond fan motor and air is moving. Unit is making ice. RK"
We serviced a
LG WASHER FRONT LO
Model DLEX3370V
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
06/17/2026
"Found unit dented on side, popped out side and straightened, leveled unit and tested operation all checks ok svf paid $149.95 CC Auth# ARL3F3"
We serviced a
WHIRLPOOL DRYER
Model WED5100HC3
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
06/17/2026
Installed repair kit runs all ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC236SPS02
Near Albuquerque, New Mexico 87111
Jason
Job Details:
06/17/2026
checked unit found ice maker feeler arm checks ok unit operation checks ok. unit is operating as designed at this time. spoke to cx about reviews
We serviced a
MAYTAG REFRIGERATOR
Model MRFF4236RZ02
Near Albuquerque, New Mexico 87123
Jason
Job Details:
06/17/2026
checked unit temps are within spec at this time rc @38 degrees 7 degrees in freezer section. unit also does not have a lot of massin either section to hold cold. unit operation checks ok at this time spoke to cx about review
We serviced a
LG DRYER
Model DLEX8600BE
Near Monument, Colorado 80132
Brandon
Job Details:
06/17/2026
"Found lint built up in blower fan causing issues, removed all lint and tested operation recommend vent cleaning svf paid $159.95 CC Auth# P9H4PY"
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Colorado Springs, Colorado 80917
Earl
Job Details:
06/17/2026
Customers complaint unit does not start I found the fuse was bad so i replaced it unit is operating properly at this time
We serviced a
MAYTAG WASHER
Model MHW6630HW3
Near Colorado Springs, Colorado 80919
Earl
Job Details:
06/17/2026
"Customers complaint units not spinning the moisture out of the clothes stopping early. I arrived and ran the unit into a rinse and spin it came out really well so that I tried diagnostics, the only code that I could find was door lock, which is pretty much on all front loaders. I then ran it with a bunch of towels and it ran all the way through I explained to the customer, how to load the unit unit is operating properly at this time."
We serviced a
KENMORE REFRIGERATOR
Model 106.55539400
Near Colorado Springs, Colorado 80922
Earl
Job Details:
06/17/2026
Customers complaint unit not dispensing ice.I arrived and found geaumotomo was bad.The auger motor was no longer available.I informed the customer.He paid the service charge in full authorization codeKW9XL9
We serviced a
WHIRLPOOL DRYER
Model WED5620HW2
Near Colorado Springs, Colorado 80938
Earl
Job Details:
06/17/2026
Customers complaint unit was not heating.I arrived and found that thermostats in heating element I replaced all and tested unit is operating properly at this time
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80922
Torrey
Job Details:
06/17/2026
Draining all the time even when turned off. Replaced mainboard. Now it won't drain. Drain pump is seized up and grinding rough. Went back to office to get a drain pump. Installed drain pump and ran test cycle and calibration. All good.
We serviced a
MAYTAG DRYER
Model MED6200KW1
Near Monument, Colorado 80132
Torrey
Job Details:
06/17/2026
Customer canceled. Tech notified at the door.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Socorro, New Mexico 87801
Larry
Job Details:
06/17/2026
CX complaint - Washer taked too long - Inspected unit and found F8E1 - Checked and found the valve failed - Replaced valve and tested good - Unit is good to go - Survey mentioned; used 1 W11513255 (Valve) from stock
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC236SPS02
Near Colorado Springs, Colorado 80919
Torrey
Job Details:
06/17/2026
Freezer icemaker tray is cracked into pieces and thermistor is dangling. Needs icemaker.IcemakerW11788019
We serviced a
WHIRLPOOL ELECTRIC RANGE
Model WFE500M4HS
Near Colorado Springs, Colorado 80927
Earl
Job Details:
06/17/2026
"Customers complaint unit is popping the breaker I arrived and checked the voltage. I checked the way that was wired in and tried the unit, the unit will come on, it goes to switch from bake to broil and back and it causes the breaker to pop the unit is operating to specification. I believe it is the ground arc breaker that is the issue I've seen this many times in the past The\nCode is changed to the arc fault breakers.And for some reason, it is causing this issue."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3136SZ00
Near Colorado Springs, Colorado 80919
Torrey
Job Details:
06/17/2026
Tech found no water in the icemaker. Temperature in freezer is 2 degrees. Ice tube is not frozen. Verified water is on. Cycled icemaker and it harvests. Sound of water valve but no ice. Disconnected line after filter and no water. Cx recently replaced the filter. Need filter head and water valve.W11757829WaterFilterSeatW11765019Water Inlet valve
We serviced a
MONOGRAM RANGE
Model ZGP304NT1SS
Near Vail, Colorado 81657
Erik
Job Details:
06/17/2026
ACCESS NEW CONSTRUCTIONinstall bullnoseJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
GE REFRIGERATOR
Model PSHS9PGZBCSS
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
06/17/2026
REPLACED ICE MKR AND UNIT CHECKED...AUTHO NO. 3UWV93
We serviced a
WHIRLPOOL DRYER
Model WED8127LC1
Near Colorado Springs, Colorado 80924
Ryan
Job Details:
06/17/2026
Replaced shorted heating element. Tested operation. Unit is now heating and working properly. RK
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Los Lunas, New Mexico 87031
Larry
Job Details:
06/17/2026
CX complaint - Gas smell - Inspected unit and found the gas smell is normal odor from oven ignition ans cycling - I did not find any gas leaks - Unit is operating as designed - Called Safety to document (SR23885193)
We serviced a
WHIRLPOOL DISHWASHER
Model WDT531HAPM0
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
06/17/2026
Excess suds recommend cx use affresh cleaner to remove soap
We serviced a
MAYTAG WASHER
Model MHW6630HW3
Near Eagle, Colorado 81631
Antonio
Job Details:
06/17/2026
"Installed new acu, rotor and stator then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey"
We serviced a
WHIRLPOOL DRYER
Model WED72HEDW1
Near Colorado Springs, Colorado 80918
Torrey
Job Details:
06/17/2026
Belt has come off again. Pulley wheel and some rollers aren't spinning very well even after cleaning them last visit. Replaced the maintenance kit parts. Went to reattached the belt and the motor pulley was broken off. Need to get the motor pulley.WP8066184Motor Pulley
We serviced a
SUBZERO REFRIGERATOR
Model 590
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
06/17/2026
REPLACED LISTED PART AND UNIT CHECKED OKAY
We serviced a
WHIRLPOOL DRYER
Model WED4815EW
Near Fountain, Colorado 80817
Carlos
Job Details:
06/17/2026
Unit failed airflow test hosehold vent needs to be cleaned and inspected
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ00
Near Los Lunas, New Mexico 87031
Larry
Job Details:
06/17/2026
CX complaint - Not making ice - Inspected unit and foudn E2 error - Replaced IM and tested good - Unit is ggood to go - Survey mentioned; used 1 W11658802 (Ice Maker) from stock
We serviced a
WHIRLPOOL DRYER
Model WED8900BW0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
06/17/2026
"Debris found in tension pulley, sanded down runs all ok cx paid SC and Prev. Maintenance fees $269.90 CC Auth# JPMUJA"
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Pueblo West, Colorado 81007
Mathew
Job Details:
06/17/2026
Replace condenser. Blow out lines. Pull into deep vacuum. Charge to spec. Monitor temps and pressures. All okay.
We serviced a
SAMSUNG WASHER
Model WA50R5400A
Near Colorado Springs, Colorado 80906
Brandon
Job Details:
06/17/2026
"Called cx to make sure unit was working properly and collect labor, unit working, cx called office to pay labor"
We serviced a
MAYTAG REFRIGERATOR
Model MRFF4236RZ02
Near Albuquerque, New Mexico 87123
Jason
Job Details:
06/17/2026
checked unit temps are within spec at this time rc @38 degrees 7 degrees in freezer section. unit also does not have a lot of massin either section to hold cold. unit operation checks ok at this time spoke to cx about review
We serviced a
MAYTAG DISHWASHER
Model MDTS7024SZ0
Near Gold Hill, Oregon 97525
Kyle
Job Details:
06/16/2026
"Found unit extremely slow to drain, checked filters, all filters clear, checked garbage disposal for blockage, found build up of grease in extended drain line into garbage disposal, cleared grease blockage and tested unit, unit is operating as intended."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Shady Cove, Oregon 97539
Kyle
Job Details:
06/16/2026
"Customer states unit is making screeching noise at end of cycle, ran large load of towels through whole normal cycle. Unit is operating as intended. Advised customer that if issue persist, need to take a video or audio recording of noise to show technician. Can not duplicate customer concern."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Eagle Point, Oregon 97524
Kyle
Job Details:
06/16/2026
"Ran unit in drain and spin, unit is not moving excessively. Raised foot slightly on right front. Unit is operating as intended. Informed customer on how to use unit as this unit is new style and design that what the customer is accustomed to."
We serviced a
SAMSUNG RANGE
Model NX60A6311SS/AA
Near Rogue River, Oregon 97537
Chris
Job Details:
06/16/2026
Replaced the igniter and temperature sensor. Tested.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS09
Near Redmond, Oregon 97756
Richard
Job Details:
06/16/2026
Installed new icemaker and inlet valve cycle tested unit all tested good at this time
We serviced a
WHIRLPOOL WALL OVEN
Model WOS51EC0HS01
Near Glenwood Springs, Colorado 81601
James R
Job Details:
06/16/2026
Signed disclaimer. Removed unit and replaced cooling fan. Re-installed unit and then set temp to 350 degrees to test operation. Cooling fan came on and no error code came up. So unit is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS09
Near Basalt, Colorado 81621
James R
Job Details:
06/16/2026
Signed disclaimer. Evac system. Then removed compressor and drier. Installed drier and compressor. Pressure test system 240 psi took pic. Pressure held no leaks. Evac system. Held. Re-charged system. Lo side -8 Hi side 55 psi took pic. Unit is cooling. Operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Frisco, Colorado 80443
Erik
Job Details:
06/16/2026
help ag
We serviced a
WHIRLPOOL WASHER
Model WFW6605MW1
Near Keystone, Colorado 80435
Erik
Job Details:
06/16/2026
help ag
We serviced a
MIELE DRYER
Model TWI180WP
Near Keystone, Colorado 80435
Erik
Job Details:
06/16/2026
CONNECT TO MDU - APPLY VARIANTS PROGRAM AND CHECK ERROR CODESF66 AIR LEAK DETECTED - ALT 9KFILTER AND HANDLE ARE MISSINGFILTER 12551630HANDLE 9657041TEST UNIT AND LOWER RESTRICTION SENSOR VALUE: PASSJOB COMPLETEBILL SENT TO CX VIA IWALLET $274.95CX NOT AVAILABLE FOR PAYMENT/ SIGNATUE
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FPFU19F8WFF
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
06/16/2026
Removed door and adjusted hinge so that door no longer rubbing on bottom panel causing it to come loose. RK
We serviced a
GE REFRIGERATOR
Model GWE22JYMCFFS
Near Silverthorne, Colorado 80498
Erik
Job Details:
06/16/2026
ACCESS NEW CONSTRUCTIONMANUAL DEFROST REQUIRED - CLEAN ICE FROM BASIN OF FZ COMPARTMENT/ REMOVE ICE BLOCKAGE FROM IM ASM AND MANUALLY DEFROST UNIT/ TEST: IM ASM: PASSJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AFL
Near Pueblo, Colorado 81001
David
Job Details:
06/16/2026
"Installed ordered part, fan running good, normal sounds."
We serviced a
SAMSUNG WASHER
Model WF45T6000AW/A5
Near Pueblo, Colorado 81006
David
Job Details:
06/16/2026
"Checked washer, washer solid to floor, ran cycle, normal sounds and vibrations. Advised cx of possible out of balance situations."
We serviced a
FRIGIDAIRE RANGE
Model FCRI3062ASB
Near Pueblo, Colorado 81004
David
Job Details:
06/16/2026
"Checked range, they only have one pan that is induction ready. Showed them how to test pans for compatibility. Stove top works properly."
We serviced a
MAYTAG WASHER
Model MVW6230HW0
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
06/16/2026
Installed Drain Hose and harness
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Belen, New Mexico 87002
Larry
Job Details:
06/16/2026
Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
MAYTAG RANGE
Model MER5551BAB
Near Pueblo West, Colorado 81007
James
Job Details:
06/16/2026
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Pueblo West, Colorado 81007
James
Job Details:
06/16/2026
Found unit with f2e1 error indicating stuck key. Replaced main board tested ops all ckok
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Colorado Springs, Colorado 80922
Torrey
Job Details:
06/16/2026
"Tech removed and replaced front panel, felt and thermostat kit. Tested good for heat and the cx said it is much quieter."
We serviced a
SPEED QUEEN WASHER
Model AWNE9RSN116TW01
Near Colorado Springs, Colorado 80924
Torrey
Job Details:
06/16/2026
Washing machine is at a diagonal from all the spin movement. It can move to the door! Tech support says to get the feet pads that stick really well. It doesnt qualify for warranty service. Part 155P3
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, Colorado 80921
Torrey
Job Details:
06/16/2026
Removed and replaced the console ui. Ran a normal cycle with wet clothes. Stopped at 11 minutes. Unplugged and ran again but only the relay clicks but the motor does not. Initial heard a buzzing start which made the tech suspect that it could be a motor issue. Need to order motor and blower wheel.W1492434 motor 697772 blower wheel
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Medford, Oregon 97504
Kyle
Job Details:
06/16/2026
"Found unit with power to unit but not starting, replaced capacitor and tested. Unit is operating ad intended."
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Redmond, Oregon 97756
Richard
Job Details:
06/16/2026
Installed new capacitor and shift actuator cycle tested unit all tested fine at this time
We serviced a
SAMSUNG REFRIGERATOR
Model RF90F29EECRAA
Near Pueblo, Colorado 81005
Brandon
Job Details:
06/16/2026
"replaced condenser and held vaccum, charged unit and tested operation all checks ok hass passed"
We serviced a
SAMSUNG WASHER
Model WA50R5400A
Near Colorado Springs, Colorado 80906
Brandon
Job Details:
06/16/2026
replaced all dampers and tested operation all checks ok hass passed
We serviced a
SAMSUNG REFRIGERATOR
Model RF23B7671SR/AA
Near Colorado Springs, Colorado 80905
Brandon
Job Details:
06/16/2026
"Nugget ice maker tray is cracked, replaced ice. aker and reset, all checks ok hass passed"
We serviced a
KITCHENAID RANGE
Model KFGC500JSS05
Near Depoe Bay, Oregon 97341
Nathan
Job Details:
06/16/2026
Right rear burner would not lock into lock position at manifold Any little bump would start burner Replaced right side manifold and issue is solved Tested Advised of survey Disclaimers on file
We serviced a
ELECTROLUX DRYER
Model ELFE7637AT1
Near Lincoln City, Oregon 97367
Nathan
Job Details:
06/16/2026
Both getting rollers has a chunk out of them causing a noise during operationTestedAdvised of survey
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
06/16/2026
Installed control ran tests and calibration runs all ok
We serviced a
GE DRYER
Model GTD48EASW0WB
Near Lincoln City, Oregon 97367
Nathan
Job Details:
06/16/2026
Plastic peice on rear hub had cracked causing a thumping noise Replaced Tested Advised of survey
We serviced a
KITCHENAID WALL OVEN
Model KODE500ESS20
Near New Castle, Colorado 81647
James R
Job Details:
06/16/2026
Signed disclaimer. Removed unit and replaced broil element and wire harness. Re-assembled and installed unit then test operation of broil it is working. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model GX5SHDXVQ02
Near Santa Fe, New Mexico 87506
Jason
Job Details:
06/16/2026
Installed drain tube and cleared ice unit operation checks ok. spoke to cx about review Auth code: NWKRUM$486.51
We serviced a
WHIRLPOOL ICE MACHINE
Model KUIX535HPS02
Near Santa Fe, New Mexico 87501
Jason
Job Details:
06/16/2026
Checked unit found that unit just needs cleaning at this point ran unit to check operation all other functions check ok. cx to run clean cycle. if issue persists they will call back. spoke to cx about review