Service History 57 - D3 Appliance

We serviced a

SAMSUNG WASHER

Model WF45R6300AV/US

Near Fountain, CO 80817

Joseph

Job Details: 12/12/2023

I was able to verify the issue I found the customer has a broken tub due to the concrete blocks on the unit breaking and puncturing tub. Unfortunately customer has decided to replace unit due to price of repair

We serviced a

GE WASHER

Model GUD27ESPM1DG

Near Colorado Springs, CO 80905

Roman

Job Details: 12/12/2023

"Tried to get the washer to fill but it would not, checked the valves and either hot or cold water valve was off. Turned it on and washer still would not fill. Turned the pressure switch knob and reset it and washer started filling and agitating. Washer running through all the cycles. Paid sc"

We serviced a

WHIRLPOOL WASHER

Model WFW94HEAW0

Near Colorado Springs, CO 80910

Joseph

Job Details: 12/12/2023

"I was able to confirm customers issue the lock wouldnt open and the customer had a error code for the lock. Replaced lock and tested unit job complete Service fee 129,95Labor 189.95Parts 207.17Tax 16.99Msrp 14.95Total 558.62"

We serviced a

WHIRLPOOL WASHER

Model MVWB765FW3

Near Colorado Springs, CO 80910

Joseph

Job Details: 12/12/2023

Retrieved part

We serviced a

SAMSUNG REFRIGERATOR

Model RF28R7201S

Near Colorado Springs, CO 80910

Joseph

Job Details: 12/12/2023

"I was able to verify issue the unit would not dispense Ice, I was able to clear the ice shoot and the unit began to dispense ice job complete"

We serviced a

WOLF RANGE GAS

Model DF486GI

Near Colorado Springs, CO 80907

Ralph

Job Details: 12/12/2023

installed part and unit checked okay

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Colorado Springs, CO 80909

Brandon

Job Details: 12/12/2023

"Errors f7e6, f8e0, f0e2, replaced valve and tested op all checks ok"

We serviced a

MAYTAG WASHER

Model MVW6500MW0

Near Silt, CO 81652

James R

Job Details: 12/12/2023

"Nut on main pulley cam loose. Replaced cam asy and belt WPW10006384 and W10721967 Put some extra loctite on shaft. Nut is really tight. Run thru diagnostics did just fine operation is normal. No error codes when done. Please fill out whirlpool tech satisfaction survey. Thank You.; used 1 WPW10006384 (Belt (Washer)), and 1 W10721967 (Cam) from stock"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRV986FDEM01

Near Silverthorne, CO 80498

Antonio

Job Details: 12/12/2023

Installed new power board and ice motir unitvtested good $207.45 CK Auth# EAL3M4

We serviced a

BOSCH VENT HOODS

Model HUI80553UC/01

Near Colorado Springs, CO 80904

Roman

Job Details: 12/12/2023

Called Bosch tech support and the part is not replaceable. tech support recommended getting a mallet to flatten it out. Pulled the support out and tried to flatten the best I could. Doesnt seem to be doing anything since its riveted in. Recommend to cx bring the hood back to where they got it. Case #410F3930889

We serviced a

JENN-AIR REFRIGERATOR

Model JBSFS42NMX00

Near Dillon, CO 80435

Antonio

Job Details: 12/12/2023

Installed new drawers and ui panel unit tested good

We serviced a

SAMSUNG WASHER

Model WA49B5205AW/US

Near Colorado Springs, CO 80905

Mathew

Job Details: 12/12/2023

"Replaced pan module, test op all okay. Found loose connections on water supply lines, tightened all okay."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ08

Near Pueblo West, CO 81007

David

Job Details: 12/12/2023

Checked dispenser Motor binding upReplaced motor Working good now

We serviced a

SUB ZERO WARMING DRAWER

Model ID-30R

Near Colorado Springs, CO 80903

Ralph

Job Details: 12/12/2023

"this isa warrantied unit, somehow, the control board was reset, subzero helped me reprogram the control and unit checked okay"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ05

Near Pueblo, CO 81005

James

Job Details: 12/12/2023

installed leds switch not needed. toghtened handle and tested ops. all ckok

We serviced a

KITCHENAID REFRIGERATOR

Model KBSD702MPS00

Near Monument, CO 80132

Glenn

Job Details: 12/12/2023

Remove Stuck / Broken Ice Bucket. Install New Bucket. All OPS Test:OK

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ0

Near Florissant, CO 80816

Mathew

Job Details: 12/12/2023

F7e1 motor error found. Replaced sump assy. Test op all okay.

We serviced a

GENERAL ELECTRIC REFRIGERATOR

Model CYE23TSDCSS

Near Colorado Springs, CO 80906

Ralph

Job Details: 12/12/2023

"unit displaying refrigerant leak, cust to replace...autho no. MAHMEK"

We serviced a

MAYTAG DISHWASHER

Model MDB9959SKZ0

Near Peyton, CO 80831

Aaron

Job Details: 12/12/2023

"F8E4 error code upon arrival, leak detection, inspected unit and found no leaks at time of inspection, customer states sink flooded the floor prior to issue, unit is working well now.Auth 129.95 hc ck 6864 #P4UVM3"

We serviced a

HISENSE REFRIGERATOR

Model HRF266N6CS

Near Colorado Springs, CO 80951

Kris

Job Details: 12/12/2023

installed ice maker ran test op all ok at this time.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FRSS2623AS6

Near Colorado Springs, CO 80922

Jessie

Job Details: 12/12/2023

Replaced bd. Test ops. All ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ08

Near Colorado Springs, CO 80917

Kris

Job Details: 12/12/2023

installed all parts sent ran test op all ok at this time. cx will monitor unit.

We serviced a

COVE DISHWASHER

Model DW2450

Near Colorado Springs, CO 80906

Ralph

Job Details: 12/12/2023

"installed parts did not see anty waer leaking after replacing parts, unit checked okay"

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Colorado Springs, CO 80908

Aaron

Job Details: 12/12/2023

"Removed and replaced motor sump assembly, tested and working well now, no leaks, installed litmus strip and advised customer of 5 star survey."

We serviced a

WOLF WARMING DRAWER

Model WWD30

Near Colorado Springs, CO 80918

Kris

Job Details: 12/12/2023

cx had 2 screws that fell from top if drawer. instaled ran test op all ok at this time.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX735SDHZ08

Near Colorado Springs, CO 80920

Glenn

Job Details: 12/12/2023

"Noise started back up about 6 hours after I completed repair. Now it is intermittent. I was able to duplicate noise. Adjusted Iceroom fan, also used cardboard in Frzr Evap Fan Cover to attempt silencing vibration noise. All OPS Appear Normal at this time."

We serviced a

MAYTAG DRYER

Model MED6630HW2

Near Colorado Springs, CO 80918

Glenn

Job Details: 12/12/2023

"Unit stopped heating. Long dry times. Reseat connections to Heating circuit & controls. All OPS Test:OK , Unit is now working properly. Vent system appears to be ok.. customer recently had vent cleaned."

We serviced a

COVE DISHWASHER

Model DW2450

Near Colorado Springs, CO 80919

Ralph

Job Details: 12/12/2023

replaced parts andunit checked okay

We serviced a

MAYTAG WASHER

Model MHW5630HC3

Near Florissant, CO 80816

Mathew

Job Details: 12/12/2023

"F6e1 f0e2 f5e2 f9e1 Found drain pump clogged, unplugged. Cleared drain and test op, all okay. If issue persists, unit will need control and drain pump."

We serviced a

BOSCH DISHWASHER

Model SHPM78Z54N/01

Near Colorado Springs, CO 80904

Ralph

Job Details: 12/12/2023

"piece of wood under the counter top was interferring with the door closing and would popdoor open intermittently, pulled unit out to stop it from interferring with the door and unit worked correctly"

We serviced a

BOSCH DRYER

Model WTG865H4UC

Near Monument, CO 80132

Kris

Job Details: 12/12/2023

ran test op. unit has multiple settings suggest reading cx hand book.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730PAHZ0

Near Colorado Springs, CO 80924

Aaron

Job Details: 12/12/2023

"Circulation motor is shorted out, unit only fills and drains, rest of unit is in good condition, Needs motor sump assembly. Approved onsite. Removed and replaced assembly, tested and working well now, no leaks, installed litmus strip. Motor sump assembly w11665769 $217.94Tax $17.87Supplies $14.50Hc $129.95Labor $259.95Total job $640.21Approved onsiteNo return on parts Auth total due $640. 21#4HN4W9"

We serviced a

BOSCH MICROWAVE

Model HMC80252UC-05

Near Colorado Springs, CO 80919

Ralph

Job Details: 12/12/2023

"unit has a broken glass in dor, will need a new door, cust to purcahse part and install hisself...aytho no. MHCT3P"

We serviced a

WHIRLPOOL DRYER

Model WED4815EW1

Near Colorado Springs, CO 80918

Glenn

Job Details: 12/12/2023

"not drying. it will, but it takes at minimum 3 tries where previously it was done in one . Vent system is completely restricted. Nothing coming out at Outside Vent. Paid SC Fee of $129.95. Autho# NV9VPV"

We serviced a

SUBZERO REFRIGERATOR

Model 550

Near Colorado Springs, CO 80908

Jessie

Job Details: 12/12/2023

Replaced refrig tstat. Test op. Unit cooking well all ok

We serviced a

WHIRLPOOL WASHER

Model WED8500DC0

Near Colorado Springs, CO 80908

Jessie

Job Details: 12/12/2023

Replaced valve assy. Verified issue resolved all okLeak strip under unit.

We serviced a

SAMSUNG DRYER

Model DVE45T3400P

Near Pueblo West, CO 81007

James

Job Details: 12/12/2023

"Installed ordered part tested ops all ckok. advised to have vents cleaned, how to properly mount vent and of the new element smell"

We serviced a

GE REFRIGERATOR

Model DFE28JSHBSS

Near Colorado Springs, CO 80908

Jessie

Job Details: 12/12/2023

Replaced bad fan assy .test op. All ok

We serviced a

GENERAL ELECTRIC WASHER

Model GTW335ASN2WW

Near Woodland Park, CO 80863

Mathew

Job Details: 12/12/2023

Replaced control and lid switch. Test op.

We serviced a

JENNAIR DOUBLE WALL OVEN

Model JJW2830WR00

Near Pueblo West, CO 81007

James

Job Details: 12/12/2023

installed ordered part tested ops all ckok. collected 215.95 $215.95 CC Auth# 4U99RT

We serviced a

SAMSUNG REFRIGERATOR

Model RF23M8570SR/AA

Near Colorado Springs, CO 80917

Joseph

Job Details: 12/12/2023

"I was able to verify the issue I found the customers wiring had got caught in the deli door, unfortunately this wiring has ripped and is not orderable job complete"

We serviced a

BLUESTAR RANGE GAS

Model RNB

Near Colorado Springs, CO 80924

Kris

Job Details: 12/12/2023

installed thermistat and safety valve. 703304

We serviced a

DACOR WALL OVEN

Model ECPD230B

Near Colorado Springs, CO 80906

Jessie

Job Details: 12/12/2023

Found bad relay bd upper.Relay bd#de81-08448aTax $Sc $149.95Msrp $14.50Labor $249.95Total $No return on partsUnit part nla. Customer wants to try and source. Will call wheb gets part

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Pueblo West, CO 81007

James

Job Details: 12/12/2023

"found loose panel causing a vibration. secured panel and tested all ops test good, noise has gone away. advised cust that panels can become slightly loosened during normal use and that it is normal and to be expected."

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRB543CMJZ00

Near Cascade-Chipita Park, CO 80809

Mathew

Job Details: 12/12/2023

"Found water fill line fell off of fitting. Cleared fitting of ice and test op, all okay."

We serviced a

MAYTAG WASHER

Model MVW6500MW1

Near Albuquerque, NM 87121

Larry

Job Details: 12/12/2023

Installed Capacitor and tested good - Unit is good to go

We serviced a

MAYTAG DRYER

Model MEDC465HW0

Near Rio Rancho, NM 87144

Larry

Job Details: 12/12/2023

Installed element and cutout and tested good - Unit is good to go

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHM0A

Near Rio Rancho, NM 87144

Larry

Job Details: 12/12/2023

Installed ice maker and tested good - Unit is good to go

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS331SDHM00

Near Santa Fe, NM 87507

Jason

Job Details: 12/12/2023

checked unit temps check ok ice bin is full. no signs of unit not cooling. unit opperating as designed at this time

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW2

Near Rio Rancho, NM 87144

Larry

Job Details: 12/12/2023

Installed suspension and tested good - Unit is good to go

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF560SEHZ03

Near Santa Fe, NM 87507

Jason

Job Details: 12/12/2023

could not verify cx complaint at this time unit is opperating as designed

We serviced a

MAYTAG DRYER

Model MGD4500MW1

Near Santa Fe, NM 87508

Jason

Job Details: 12/12/2023

installed parts unit checks ok

We serviced a

KITCHENAID RANGE

Model KDRP463LSS05

Near Corrales, NM 87048

Larry

Job Details: 12/12/2023

During repair I found there was a large presence of mice inside the unit - The main control is covered with mouse urine and feces and I also found chewed wires - The main control is NLA - Called techline and was disconnected after 37min

We serviced a

MAYTAG RANGE

Model MER8800FZ

Near Frisco, CO 80443

Antonio

Job Details: 12/12/2023

Found loose connection at wire block tightened unit tested good

We serviced a

MAYTAG REFRIGERATOR

Model MSS25N4MKZ04

Near Colorado Springs, CO 80920

Roman

Job Details: 12/12/2023

Checked freezer temps and it was getting a reading of about 1 to 12 degrees with doors being opened and closed. Checked the gasket and it is okay. Evaporator has good frost built up on it and fan is running. Called tech support and they had said that the fridge is not meant to be in 55 degree or colder place like the cx garage which is where it is. Freezer also has nothing in it and freezer is meant to have stuff in it to keep the temperatures from fluctuating a lot. Recommended to cx to fill ot with water jugs and and smaller waters in the door to see if things freeze and fridge stays at temps. Also recommend getting a temp gage. If cx calls back recommend coming back with a temperature thermostatTemp thermostat #WPW10384183 File #7738001432

We serviced a

BOSCH M/W OTR

Model HMV8053U

Near Colorado Springs, CO 80918

Kris

Job Details: 12/11/2023

installed door switches and fuse ran test op all ok at this time.

We serviced a

MAYTAG DRYER

Model MED6630HC0

Near Rio Rancho, NM 87124

Larry

Job Details: 12/11/2023

"CX complaint - Dryer not heating - Inspected unit and found the element failed and the rollers are squeeling - Installed new element and roller kit from TS and tested good - Unit is good to go - CX is PIF; used 1 WP3387747 (Element (Front Blower)), and 1 4392067 (Dryer Kit (4 Roller)) from stock"

We serviced a

AMANA WASHER

Model WTW4816FW3

Near Rio Rancho, NM 87144

Larry

Job Details: 12/11/2023

CX complaint - Squeeling noise - Inspected unit and found the splutch failed - Replqced with TS and tested good - Unit is good to go; used 1 W10721967 (Cam) from stock

We serviced a

WHIRLPOOL MICROWAVE

Model WMH78019HW06

Near Rio Rancho, NM 87144

Larry

Job Details: 12/11/2023

CX complaint - MW sparked inside - Inspected unit and found the Wave Guide Cover has excessive grease on it that burned a bit when in use - Removed cover to inspect wave guide and checks good - Unit is operating as designed - Advised cx to clean unit periodically.

We serviced a

KITCHENAID DISHWASHER

Model KDTM404KPS0

Near Corrales, NM 87048

Larry

Job Details: 12/11/2023

Installed hinges and tested good - Unit is good to go

We serviced a

ASKO DISHWASHER

Model n/a

Near Colorado Springs, CO 80919

Ralph

Job Details: 12/11/2023

"unit was stuck in cycle, cleared the setting then unpluggedtoreset the board, and unit started washing, unit checked okay...autho no.9F44KH"

We serviced a

WHIRLPOOL RANGE

Model WFE535S0LZ2

Near Colorado Springs, CO 80923

Aaron

Job Details: 12/11/2023

"Tested unit at 350f with +30 calibration, average temperature 352, working well now,advised customer of usage and survey."

We serviced a

SAMSUNG DISHWASHER

Model DW80R7060US/AA

Near Colorado Springs, CO 80908

Brandon

Job Details: 12/11/2023

"Replaced support string and tested op all checks ok hass passed, called techline and documented"

We serviced a

MAYTAG DISHWASHER

Model MDB4949SKZ1

Near Colorado Springs, CO 80911

Carlos

Job Details: 12/11/2023

Installed gasket and switch cx will observe .

We serviced a

SAMSUNG DISHWASHER

Model DW80B7070US/AA

Near Monument, CO 80132

Brandon

Job Details: 12/11/2023

"Error 5c1, drain getting voltage, found debris in drain pump, removed debris and tested op all checks ok hass passed"

We serviced a

BOSCH WASHER

Model WAW285H2UC/20

Near Aspen, CO 81611

Erik

Job Details: 12/11/2023

install doorjob complete

We serviced a

SAMSUNG REFRIGERATOR

Model RF28HMELBSR/AA

Near Pueblo, CO 81001

Joseph

Job Details: 12/11/2023

"I was able to confirm issue I found the unit has a frosting over icemaker, I replaced all parts in units service buliten job complete"

We serviced a

SAMSUNG REFRIGERATOR

Model RF28R7351SG/AA

Near Pueblo, CO 81005

Joseph

Job Details: 12/11/2023

"I was able to confirm issue, I found that the unit will need a new icemaker because the icemaker is not producing Ice.replaced icemaker and tested unit job complete"

We serviced a

WHIRLPOOL RANGE

Model WFG320M0MS0

Near Pueblo West, CO 81007

James

Job Details: 12/11/2023

"found bottom of oven cavity warped causing it to not stay in place. replaced with preordered part. tested ops, all ckok"

We serviced a

SAMSUNG WASHER

Model WF45A6400AV

Near Pueblo, CO 81005

James

Job Details: 12/11/2023

installed ordered part tested ops. ui now responds as designed

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SNHM06

Near Colorado Springs, CO 80921

Kris

Job Details: 12/11/2023

unit is in garage showed cx unit needs to be above 55 degrees per cx hand book page 7.

We serviced a

FRIGIDAIRE WALLOVEN

Model FGET2745KFA

Near Colorado Springs, CO 80923

Kris

Job Details: 12/11/2023

installed element ran test op all ok at this time

We serviced a

BLUESTAR RANGE

Model RNB486GSS

Near Colorado Springs, CO 80923

Kris

Job Details: 12/11/2023

installed ignitor ran test op all ok at this time.

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC0

Near Peyton, CO 80831

Aaron

Job Details: 12/11/2023

"F1E2 motor control error code upon arrival, outlet has good polarity, 123.8v to control, corrected connection at stator harness, checked slider, tested through diagnostics three times, working well and no further error codes. Discussed with techline. SR7737999012"

We serviced a

SAMSUNG DRYER

Model DVG52A550

Near Colorado Springs, CO 80938

Mathew

Job Details: 12/11/2023

"Found hc error on test. Cleared vent and test again, hc error still there. Test thermoster found broken wire leading to thermistor. Repaired and test op all okay."

We serviced a

GE OVEN

Model JBP24W0K4WW

Near Colorado Springs, CO 80907

Ralph

Job Details: 12/11/2023

installed partand unit checked okay

We serviced a

SAMSUNG REFRIGERATOR BOT

Model RF28R7351SRI

Near Colorado Springs, CO 80922

Mathew

Job Details: 12/11/2023

"C6 c47 c13 found multiple issues, ice room door operating non stop. Will need switches and motor, assy is not available. Unit may also need control $398.90 DA94-04603A. Svf $129.953405-001117 x2 $48.74 ea. $97.48 +$7.99DA31-00079D $150.68 + tax $12.36MPs $14.50 $412.96Labor $219.95 Cx holding off for now on repair. 129.95 paid today. $142.95 CC Auth# KLPA9L"

We serviced a

SAMSUNG REFRIGERATOR

Model RF29A9671SR/AA

Near Colorado Springs, CO 80920

Mathew

Job Details: 12/11/2023

"Fixed connection on reed switch, unit now working as expected."

We serviced a

GE DRYER

Model GTD75ECSL0WS

Near Colorado Springs, CO 80915

Roman

Job Details: 12/11/2023

"Ran the dryer and it squealing, took the dryer aprt and the and the front bearing is down to metal. Recommend replacing the front bearing assyFront bearing assy #WE03X23875 $149.42Tax $12.25Total parts $161.67MPs $14.50Labor $189.95Sc $129.95Total cost $496.07Paid sc $129.95 CC Auth# N39YAX"

We serviced a

GE RANGE

Model CES700P3M1D1

Near Colorado Springs, CO 80919

Roman

Job Details: 12/11/2023

"Ran the oven at 350 degrees and oven gets to about 230 degrees and baking shuts off, everything else stays on. Checked all the heating elements and cooling fan it its getting volts and running. Checked the fault codes and they are indicating a cooling fan fault, or the touchpad is wearing out. Checked the rpms on the fan and its running at around 1500 rpms which is normal. Ran the oven after unplugging it and it worked fine and got it up to 450 degrees without it shutting down. Called tech support and they did not recommend replacing parts yet till the errors come up again, because it could have just reset the control board/ panel. Cooling fan #WB26X32571 $179.94Control panel #WB27X31746 $458.82Tax $MPs $14.50Labor $249.95Sc $129.95Paid sc $149.44 CC Auth# C9E4AC"

We serviced a

THERMADOR FREEZER

Model T30IF905SP/21

Near Colorado Springs, CO 80920

Ralph

Job Details: 12/11/2023

installed part and unit checked okay

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Colorado Springs, CO 80915

Carlos

Job Details: 12/11/2023

Installed sump assembly

We serviced a

KITCHENAID DISHWASHER

Model KDTE254ESS1

Near Colorado Springs, CO 80903

Carlos

Job Details: 12/11/2023

Installed tracks and supports all ok

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ0

Near Colorado Springs, CO 80904

Carlos

Job Details: 12/11/2023

"Installed sump assembly, drain pump and control board. Advised cx to have an electrician check wall outlet for dishwasher"

We serviced a

GE RANGE

Model CTD90DP3N2D1

Near Colorado Springs, CO 80906

David

Job Details: 12/11/2023

Replaced control boards Tested and is working great

We serviced a

WHIRLPOOL DRYER

Model WED7120HW0

Near Colorado Springs, CO 80910

Carlos

Job Details: 12/11/2023

Ran test op. Door was crooked readjusted door. Recommend cx have vents clean and hose shorten.

We serviced a

GENERAL ELECTRIC DISHWASHER

Model GDF630PSM3SS

Near Peyton, CO 80831

Aaron

Job Details: 12/11/2023

"Unit is intermittently not powering on at the user interface, working well at time of inspection, upon further inspection found the main control board has signs of smoking/ burning, correct polarity to the unit and sending 13v DC to the UI control, informed customer of the burning. Estimate is for the control, and customer understands that other components could have been effected. Heating element and thermostat check out okay, unit working well at time of inspection. Control WD21X32165 $168.78Tax $13.84Supplies $14.50Hc $129.95Labor $189.95Total job $517.0230 day estimate No return on parts Auth $129.95 hc #H44U43"

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Grand Junction, CO 81507

James R

Job Details: 12/11/2023

When I arrived sensing light flashing. Would not start.Unplugged to reset unit. Put into service diagnostics. No error codes. Unit went thru no issues. If water level is set to low for load items in unit can get out of balance and load may not spin out properly. Adjust load and restart. Checked water level auto sensing and deep water are working. Showed customer. Unit is working as should. Do here rattling no adjust rear panel per TSP W11695259 adjust rear panel to eleviate rattling sound in panel. Please fill out whirlpool tech satisfaction survey. Thank You.

We serviced a

SAMSUNG RANGE

Model NE63A6511SS/AA

Near Colorado Springs, CO 80920

Mathew

Job Details: 12/11/2023

Replaced board and upper assy. Test op all okay.

We serviced a

KITCHENAID VENT HOODS

Model KVIB606DSS4

Near Grand Junction, CO 81507

James R

Job Details: 12/11/2023

Pin that goes in connector wasnt straight had to straighten so would connect properly. Right rear light replaced. Test operation it is normal. Working as should. Please fill out whirlpool tech satisfaction survey. Thank You. Customer pais labor $99.95 auth code. FEEL3F

We serviced a

GE REFRIGERATOR

Model GTS17GSNKRSS

Near Colorado Springs, CO 80910

Roman

Job Details: 12/11/2023

Removed the old damaged door and installed new doorZ made sure gasket ones up and door closes properly. Fridge working great.

We serviced a

SAMSUNG REFRIGERATOR

Model RF28R7351SR/AA

Near Colorado Springs, CO 80918

Mathew

Job Details: 12/11/2023

Replaced all parts. Completed icemaker service bulletin.

We serviced a

WHIRLPOOL WASHER

Model WFW9300VU02

Near Colorado Springs, CO 80918

Glenn

Job Details: 12/11/2023

"making a loud sound during the spin cycle/ loud clatterUnit Has Bad Bearing / Spider Gear. Requires New Rear Tub Assy, Seal & Basket. Customer Declined Estimate.Paid SC Fee $129.95 , Autho# U4RANK"

We serviced a

WHIRLPOOL RANGE

Model WFG505M0BW2

Near Grand Junction, CO 81501

James R

Job Details: 12/11/2023

Signed disclaimer.Put into diagnostics. No error codes present. Slid unit out and checked sensor probe connection and at control. Did a bake cycle. Set to 350 degrees. Let cycle several times. Did not come up with any errors. Unit is operating as it should. Please fill out whirlpool tech satisfaction survey. Thank You.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730HAMZ0

Near Colorado Springs, CO 80918

Glenn

Job Details: 12/11/2023

"Reseat connections, All OPS Test:OK"

We serviced a

MAYTAG WASHER

Model MVW7232HW1

Near Grand Junction, CO 81504

James R

Job Details: 12/11/2023

Customer signede waiver. Put into service diagnostics F0E5 error off balanced load. Cleared code. If load is unbalanced enough unit will not finish cycle. Customer needs to stop cycle adjust load then restart. Checked diagnostics cycle. Unit did not shift properly. Replaced slider and clutch checked again operating as should. Did a DLMS calibration cycle. Also a unbalanced load detection cycle. All normal.

We serviced a

WHIRLPOOL RANGE

Model WFG505M0BS3

Near Colorado Springs, CO 80909

David

Job Details: 12/11/2023

Ignitor burned-out Replaced Ignitor Working good

We serviced a

WHIRLPOOL DRYER

Model MEDB835DC4

Near Colorado Springs, CO 80921

Glenn

Job Details: 12/11/2023

"Pre-Paid for part 4392067 $75.90, tax $6.22,total $82.12.Paid Labor $199.95 , MPS $14.50 = $214.45 + Tip $21.45 = $235.90 , Autho# F34VE4"

We serviced a

WHIRLPOOL RANGE

Model WFE505W0JZ3

Near Peyton, CO 80831

Aaron

Job Details: 12/11/2023

"Tested unit at 350f, 30 minutes after preheat was completed exterior temperature on the left was 147f and 115 for the right, discussed with techline once more and reported findings, unit deemed working as designed and temperatures are withing limits. Advised customer of situation and survey. SR7737926275"

We serviced a

MAYTAG WASHER

Model MVW6230RHW2

Near Colorado Springs, CO 80924

Aaron

Job Details: 12/11/2023

"Removed and replaced lower harness and pump, tested unit though DLMS and diagnostic cycles, working well now. Advised customer of 5 star survey."