Service History 58 - D3 Appliance

We serviced a

DACOR DISHWASHER

Model DDW24M999US/DA

Near Colorado Springs, CO 80907

Mathew

Job Details: 04/30/2024

Replaced faulty wire harness. Test op all okay.

We serviced a

FRIGIDAIRE REFRIGERATOR

Model FPRH19D7LF1

Near Colorado Springs, CO 80906

Ralph

Job Details: 04/30/2024

UNITS DRAIN HOLE WAS CLOGGED AND CLEARED...CUST PAID TOTAL BILL AUTHO NO. A3JET4

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325FDAM01

Near Rio Rancho, NM 87124

Joe

Job Details: 04/30/2024

Cx complaint. Ice landing all over the floor. Installed ice bin and ice dispenser ordered last visit. Tested unit. Unit good to go

We serviced a

MAYTAG DRYER

Model MED6230HW1

Near Albuquerque, NM 87109

Larry

Job Details: 04/30/2024

CX complaint - Dryer starts the stops all the time - Inspected unit and found the motor failed - CX does not want to bear the cost of repair and will replace - SC paid- Auth-34XJ9R

We serviced a

WHIRLPOOL WASHER

Model WFW5605MW0

Near Manitou Springs, CO 80829

Carlos

Job Details: 04/30/2024

"Ran test, ran hard reset unit runs ok, cx had recently experience a surge with last storm, advised cx to get a surge protector. Cx asked if using heavy duty with small loads is advisable, said no, to use normal cycle or quick wash for small loads. Recommend cx use affresh tablet for cleaning washer of excess suds. As well as leaving the door open after washes to avoid any possible mold build up that might occur."

We serviced a

ASKO DRYER

Model N/A

Near Colorado Springs, CO 80904

Roman

Job Details: 04/30/2024

"Cx wanted me to run dryer and make sure its working, dryer tunes on and heats. Has a burning smell. Took off the vent hose and found lint built up. Removed it and ran dryer. Dryer didnt burn as much but recommend getting the walls cleaned. Labor 50 +89.95 + 149.95 289.90$289.90 CC Auth# is J3LT43 combined with washer ticket"

We serviced a

KITCHENAID DISHWASHER

Model KDTE234GWH0

Near Colorado Springs, CO 80919

Carlos

Job Details: 04/30/2024

"Installed wash motor, diverter and spray arm ran test used clear door, spray arm spins normally, left leak strip all ok"

We serviced a

PROFILE WASHER

Model PFQ97HSPV0DS

Near Pueblo, CO 81005

James

Job Details: 04/30/2024

Installed previous techs ordered part. Tested ops ran hp diagnostic all temps pass no error observed. Left litmus

We serviced a

KITCHENAID WALL OVEN

Model KODE500ESS20

Near Colorado Springs, CO 80924

Jerimiah

Job Details: 04/30/2024

Trim piece to be installed was in pieces. Was able to repair and install. Unit check ok.

We serviced a

FRIGIDAIRE GAS RANGE

Model FCRG3052ASA

Near Fountain, CO 80817

Jerimiah

Job Details: 04/30/2024

"Found back right burner not igniting, found burner head clogged, repaired, unit check ok."

We serviced a

MAYTAG WASHER

Model MVW6230HC0

Near Albuquerque, NM 87120

Larry

Job Details: 04/30/2024

CX complaint - Wsher making loud screaching noise - Inspected unit and found the belt and pulley worn - Replaced with TS and tested good - Unit is good to go - CX is PIF - Auth-CC3V94

We serviced a

MAYTAG DRYER

Model MED5630HW1

Near Peyton, CO 80831

Aaron

Job Details: 04/30/2024

"Heating element is shorted out due to normal use, removed and replaced element, tested unit, working and heating well now. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT970SAKZ2

Near Peyton, CO 80831

Aaron

Job Details: 04/30/2024

"Circulation motor is not effectively working, removed and replaced motor sump assembly, tested unit, working well now. Advised customer of 5 star survey."

We serviced a

MAYTAG WASHER

Model MVWP576KW0

Near Peyton, CO 80831

Aaron

Job Details: 04/30/2024

"Removed and replaced inlet valve assembly, tested unit and working well now, verified by customer. Advised customer of 5 star survey."

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Colorado Springs, CO 80927

Aaron

Job Details: 04/30/2024

"Lid latch assembly is shorted out, removed and replaced latch, tested unit through diagnostics, working well now. Advised customer of 5 star survey."

We serviced a

MAYTAG DRYER

Model MED7230HW3

Near Colorado Springs, CO 80908

Aaron

Job Details: 04/30/2024

"Removed and replaced motor and blower, tested unit, working and heating well now. Total due was previously paid."

We serviced a

WHIRLPOOL DISHWASHER

Model WDF330PAHS3

Near Colorado Springs, CO 80908

Aaron

Job Details: 04/30/2024

"Replaced roller assemblies and stops, tested unit, working well now, no leaks, installed litmus strip and advised customer of survey."

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ2

Near Pueblo, CO 81006

Domingo

Job Details: 04/30/2024

Replace part ran diagnostic cycle and pass dish washer working correctly at this time.

We serviced a

KITCHENAID DISHWASHER

Model KDTM604KBS1

Near Breckenridge, CO 80424

Antonio

Job Details: 04/30/2024

Found right door spring off due to catching on insulation reinstalled and made sure insulation not going to catch again unitvtested good

We serviced a

SCOTSMAN ICE MACHINE

Model DCE33PA-1SSD

Near Colorado Springs, CO 80904

Ralph

Job Details: 04/30/2024

REPLACED LITED PARTS AND UNIT CHECKED OKAY

We serviced a

GE RANGE

Model RBS330DR2WW

Near Glenwood Springs, CO 81601

Erik

Job Details: 04/30/2024

upon completion of diagnostics found unit to be fine.problem is do to hyper sensitivity of arc fault breaker. call GE TAG: CX needs to contact an electrition to have standard 30 amp breaker.job complete

We serviced a

SAMSUNG RANGE

Model NE63T8111SS/AA

Near Colorado Springs, CO 80916

Mathew

Job Details: 04/30/2024

Found burner switch installed upside down. Fixed switch and test op all okay.

We serviced a

SAMSUNG REFRIGERATOR

Model RF27T5501SG/AA

Near Peyton, CO 80831

Brandon

Job Details: 04/30/2024

"Error 39c, 41c, ice maker is broken needs replaced all other checks ok, PCB is 1199G, Svf paid $129.95 Auth# MCKHXV, Da97-15217d $189, Labor $189.95, Svf $129.95, Mps $14.50, Tax $15.50"

We serviced a

BOSCH DISHWASHER

Model SHV89PW73N/91

Near Aspen, CO 81611

Erik

Job Details: 04/30/2024

F18 error.prime softener tank to clear F18 water tap error.install water inlet and aquastop . all good job complete.

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Albuquerque, NM 87114

Joe

Job Details: 04/30/2024

Cx complaint. Dryer won't always start. Replaced control and ui ordered last visit. Tested multiple times. Unit good to go

We serviced a

MAYTAG WASHER

Model MVW7232HC2

Near Belen, NM 87002

Larry

Job Details: 04/30/2024

Installed and calibrated control and passed diagnistocs cycle - Unit is operating as designed

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS315SDHZ17

Near Santa Fe, NM 87507

Jason

Job Details: 04/30/2024

sr7738997964. installed parts found molex connector wasnt seated. seated connector unit checks ok

We serviced a

WHIRLPOOL RANGE

Model WFG550S0LZ5

Near Santa Fe, NM 87506

Jason

Job Details: 04/30/2024

Installed control unit opperation checks ok

We serviced a

SUB ZERO REFRIGERATOR

Model 661/0

Near Colorado Springs, CO 80904

Ralph

Job Details: 04/30/2024

INSTALLED LISTED PARTS AND UNIT CHECKED OKAY

We serviced a

MAYTAG WASHER TOP LOAD

Model MVWX655DWO

Near Colorado Springs, CO 80907

Roman

Job Details: 04/30/2024

"Noticed the agitator is very loose, checked the threads on the transmission and agitator disc and they are worn out. Recommend replacing the transmission and agitator disc. Tightened the nut on the disc and should hold for now as a temporary fixPaid sc"

We serviced a

MAYTAG DRYER

Model MEDB835DW

Near Breckenridge, CO 80424

Antonio

Job Details: 04/30/2024

"Found belt not installed properly, so i installed belt properly unit tested good"

We serviced a

WOLF COOKTOP

Model CG304T/S

Near Colorado Springs, CO 80906

Jerimiah

Job Details: 04/30/2024

"Front right and rear left burners inconsistently igniting, cleaned igniter heads and adjusted igniter wire to insulate spark further up igniter. Unit check ok"

We serviced a

WHIRLPOOL WASHER

Model WFW9640XW00

Near Colorado Springs, CO 80915

Roman

Job Details: 04/30/2024

"Noticed washer has no hot water hooked up to it, ran the washer on a cold cycle and washer started filling. Ran it again and washer did not fill with water but no error code comes up. Checked the voltage to the valve and its getting 120V. Checked the drain pump and it is okay and filter is clean. Washer draining properly. Recommend replacing the inlet valve. Installed new valve and connected the hot water. Tested the u it and checked for leaks. Washer is working great. Inlet valve #WPW10247306 $191.52Tax $15.70Parts total $207.22MPs $14.50Labor $189.05Sc $129.95Total cost $541.62; used 1 WPW10247306 (Inlet valve) from stock"

We serviced a

ZLINE SINGLE WALL OVEN

Model AWS-30

Near Colorado Springs, CO 80919

Jerimiah

Job Details: 04/30/2024

"Cust having erratic temp issues, unit being too hot one cycle and too cold the next. Zline sent out a relay board and power board to remedy situation but did not send temp sensor, parts installed. Unit also having issues with time clock adding minutes. Unit needs replacement console and it problems persist with bad cooking temps, also will need thermal sensor. Cust will try unit unit out and tell zline what is needed based on tech support recommendations. Closing call"

We serviced a

BOSCH RANGE

Model HDI7282U/03

Near Colorado Springs, CO 80919

Jerimiah

Job Details: 04/30/2024

"Warming drawer not heating, getting error 33, thermal sensor short, found harness connecting sensor to board broken, needs replacement harness connector. Harness no longer available. Charging service call. $172.44 CC Auth# 39C3HC00619630 drawer sensor00657860 power board."

We serviced a

WOLF WALLOVEN

Model DO30PM/S/PH

Near Colorado Springs, CO 80908

Jerimiah

Job Details: 04/30/2024

"Installed replacement console, unit check ok. Cust will keep track of unit functionality."

We serviced a

AMANA WASHER

Model NTW4519JW2

Near Glenwood Springs, CO 81601

James R

Job Details: 04/30/2024

"Customer signed disclaimer.Put into service diagnostics no error codes. Run thru auto test. Found a water leak at cold water hose tightened as best as could. But still leaks cannot shut cold water valve off at wall. cu7stomer will need to have repaired. Tilted unit back checked cover, pulleys and belt it is loose has been slipping will replace it. W11239857. Can see where cover has been rubbing on the floor. adjusted feet down so it doesnt and leveled unit. Also performed S.P. W11695259 to take care of vibration noise. It is important not to overload unit will cause out of balance loads and wont operate properly. Unit operating as should.; used 1 W11239857 (Belt (Washer)) from stock"

We serviced a

GE REFRIGERATOR

Model ZFSB25DTG

Near Colorado Springs, CO 80920

Eric

Job Details: 04/30/2024

"Fridge side not cooling. After inspection found RC evp fan shorted out. Upon check with parts department, evp motor no longer available, informed customer of options. No part available Tax$0Supplies$0Hc$149.95Labor$0Total$149.95Auth paid HC $149.95 TLTC33"

We serviced a

GE DRYER

Model GTD33EASK0WW

Near Gypsum, CO 81637

Erik

Job Details: 04/29/2024

install timer and test: set at 25 min/ GOODJOB COMPLETE

We serviced a

MAYTAG WASHER

Model MHW7100DCO

Near Pueblo, CO 81007

Domingo

Job Details: 04/29/2024

Reposition washer and dryer

We serviced a

MAYTAG WASHER

Model MVWB835DC5

Near Albuquerque, NM 87105

Larry

Job Details: 04/29/2024

CX complaint - Washer is making a really loud noise like grinding - Inspected unit and could not duplicate the issue - Ran diagnoatic cycle successfully - Unit is operating as drsigned

We serviced a

WHIRLPOOL RANGE

Model WEE515S0LS

Near Edwards, CO 81632

Antonio

Job Details: 04/29/2024

Unplugged ground wire heated unit to 500 degrees and then reinstall ground wire unitvtested good

We serviced a

WHIRLPOOL WALLOVEN

Model KOCE500EESS09

Near Albuquerque, NM 87120

Larry

Job Details: 04/29/2024

CX complaint - MW no working - Inspected unit and found F6E3 error - Unit needs MW appliance manager - CX does not want to bear the cost of repair - Collected SC (Auth-939FWV)Control-W11325786-$224.40Labor-$219.95MSP-$17.5Tax-$39.26

We serviced a

SAMSUNG DRYER

Model DVE50R5400V/A3

Near Fountain, CO 80817

Mathew

Job Details: 04/29/2024

Found obstruction in blower wheel housing. Vacuumed out obstruction and test op all okay. Cleared venting to wall.

We serviced a

MAYTAG WASHER

Model MAH5500BWW

Near Colorado Springs, CO 80919

Glenn

Job Details: 04/29/2024

"Bad Latch Assy, Called Techline to verify which part to order, as unsure of series model. Suggested part for Series 10. SR# 7738988385 , Latch Assy - WP22003593 $330.76 , Tax $27.12 , MPS $14.50 , Labor $179.95. Declined Estimate for now. Paid SC Fee of $89.95 + Tip $30.00 = $119.95 , Autho# L439AC"

We serviced a

WHIRLPOOL WASHER

Model WTW5010LW0

Near Albuquerque, NM 87120

Larry

Job Details: 04/29/2024

CX complaint - not washing properly - Inspected unit and found the clotch failed with the basket engaged - Replaced clutch with TS and tested good - Unit is operating as designed; used 1 W10721967 (Cam) from stock

We serviced a

HOTPOINT DRYER

Model HTX24EASK0WS

Near Colorado Springs, CO 80917

David

Job Details: 04/29/2024

"Checked dryer, found bearing dry, lubed and tested. Running good"

We serviced a

WHIRLPOOL DRYER

Model WED5605MC0

Near Edwards, CO 81632

Antonio

Job Details: 04/29/2024

Installed motor acu and blower wheel unit tested good

We serviced a

MAYTAG WASHER

Model MVW6500MW0

Near Albuquerque, NM 87120

Larry

Job Details: 04/29/2024

Installed parts listed and tested good - Unit is good to go

We serviced a

MAYTAG DRYER

Model MEDC465HW

Near Pueblo, CO 81004

Domingo

Job Details: 04/29/2024

Check the temp in the dryer on time dry and it got to 200? and it came down to 120? and then back up and I check it on sensor dry it got to 125? and thats it check the vent hose it was block I unblocked it and now its working good

We serviced a

AMANA RANGE

Model AER6303MFW5

Near Albuquerque, NM 87120

Larry

Job Details: 04/29/2024

CX complaint - Clock and lights are not working but the burners are - Inspected unit and found 240vac between L2 and Ground and nothing between L1 and Ground or between L1 and L2 - Advised CX to contact a liscensed electrician

We serviced a

WHIRLPOOL DRYER

Model WED5100HW2

Near Colorado Springs, CO 80925

Carlos

Job Details: 04/29/2024

"Installed heating element ran test all ok, recommend cx have vents cleaned and replace hose with semi-rigid hose per owners manual."

We serviced a

KITCHENAID REFRIGERATOR

Model KRFC300ESS11

Near Colorado Springs, CO 80921

Glenn

Job Details: 04/29/2024

"Actual arrival time 11:45am, Unit making clicking noise 2-3 times a day, for about 10 minutes. Reseat connections to main PCB, Checked compressor lines and started unit about 3 times to rule out noise during compressor start. Unable to duplicate noise at this time. Suggest customer video tape to record noise during issue if it ocurrs again. All OPS Test:OK"

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF507HPS03

Near Colorado Springs, CO 80911

Carlos

Job Details: 04/29/2024

"On arrival Cx explained they are concerned with temperature in freezer. I was unable to get accurate reading since unit was going through its defrost cycle, Got as low ass 10 degrees. Checked Pressures low side was -1 and high side was 145 checked for leaks with detector none found. Explained to cx to put a glass of water in their refrigerator with a thermometer and check temperature, if issue is present to call back. Installed Ice maker ran harvest cycle runs ok, cx will observe. Cx paid Labor for Ice maker Install $189.95 CC Auth# M933EV"

We serviced a

KITCHENAID DISHWASHER

Model KDTE234GPS1

Near Colorado Springs, CO 80924

Glenn

Job Details: 04/29/2024

"Verifiy no water leaks at door, supply valve, etc, Reseat connections to PCB, Ran Diag Test 2X, Did see some suds, and suggested running clean washer product, in case issue caused by suds overdose. Also suggest run hot water at sink prior to start of cycle. All OPS Test:OK"

We serviced a

MAYTAG DRYER

Model MED6230HW3

Near Colorado Springs, CO 80906

Carlos

Job Details: 04/29/2024

"Installed control board and Ui and moisture sensor, ran test heated to 165 degrees all ok, Cleaned moisture sensor electrodes all ok"

We serviced a

WHIRPOOL REFRIGERATOR

Model ET18NMXFW03

Near Edwards, CO 81632

Antonio

Job Details: 04/29/2024

Unit needs tstat and heater cx holding on repair but still thawed out Autho# ffe933$149.95$189.95$339.90

We serviced a

SAMSUNG REFRIGERATOR

Model RF23HCEDBSR/AA

Near Colorado Springs, CO 80915

Brandon

Job Details: 04/29/2024

"No errors, called tech support did ice maker inspection, leaking from Ice route, need new ice route per Samsung"

We serviced a

WHIRLPOOL WASHER

Model WFW5605MW1

Near Pueblo, CO 81004

Domingo

Job Details: 04/29/2024

Replaced board ran a whole cycle on quick to see if it got stuck in the 1 min spin and it got to end everything test it good

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS571CIHZ04

Near Colorado Springs, CO 80926

Carlos

Job Details: 04/29/2024

"Ran test found broken wires at bottom of door, Needs a new door cx will no repair."

We serviced a

UNKNOWN REFRIGERATOR

Model PSS26LGRAWW

Near Pueblo, CO 81001

James

Job Details: 04/29/2024

Installed ordered parts replaced cust supplied filter. tested ops all ckok. Took b&a photos

We serviced a

KITCHENAID REFRIGERATOR

Model KRBR109ESS00

Near Colorado Springs, CO 80919

Roman

Job Details: 04/29/2024

Removed the front grate and showed cx how to clean the condenser coils. Double checked the fridge and its working great. Paid sc check

We serviced a

WHIRLPOOL DISHWASHER

Model WDF331PAHS1

Near Colorado Springs, CO 80927

Aaron

Job Details: 04/29/2024

"Upper rack track stop tabs are broken, replaced stripper and tested unit, working well now, no leaks, installed litmus strip and advised customer of survey."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS05

Near Falcon, CO 80831

Aaron

Job Details: 04/29/2024

"Deli drawer cover missing, installed cover, rest of unit is working well. Advised customer of 5 star survey."

We serviced a

MAYTAG DRYER

Model MEDB765FW0

Near Colorado Springs, CO 80918

Glenn

Job Details: 04/29/2024

"Install New T-stats, All OPS Test:Ok"

We serviced a

SAMSUNG REFRIGERATOR

Model RF28T5001SR/AA

Near Colorado Springs, CO 80919

Brandon

Job Details: 04/29/2024

"Error 21c, bearings out in freezer fan,da97-21002a $265.58, Labor $199.95, Svf $129.95, Mps $14.50, Tax $21.78"

We serviced a

WHIRLPOOL RANGE

Model WEG745H0FS0

Near Colorado Springs, CO 80924

Brandon

Job Details: 04/29/2024

Replaced blower fan and tested op all checks ok

We serviced a

AMANA DRYER

Model NED4655EW1

Near Pueblo, CO 81001

James

Job Details: 04/29/2024

Found stator open causing no heat. Replaced with kit. All ops test good.

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRX986SIHZ00

Near Colorado Springs, CO 80917

Glenn

Job Details: 04/29/2024

"Customer indicated that the unit only harvested 1 batch of ice since last visit. Install New UI Control. Fill Tube heater Test > Pass, Harvest Test > Pass , Fill Test > Pass. Allow 72 hours for ice production. If problem continues, order main control."

We serviced a

WHIRLPOOL DISHWASHER

Model WDT540HAMZ0

Near Rio Rancho, NM 87124

Joe

Job Details: 04/29/2024

Cx complaint. Not cleaning dishes. Inspected unit. Sump motor not working. Replaced sump motor. Tested unit. Unit good to go

We serviced a

GE REFRIGERATOR

Model ZIC30GNHAII

Near Beaver Creek, CO 81620

Erik

Job Details: 04/29/2024

upper FF door hinge NOT fully secure - uninstall door panel and correct door mount hardware/ reinstall door panelTEST IM asm: GOOD per unit spec IM will only harvest if set at or below ZERO degreesCX not available for signature

We serviced a

GE REFRIGERATOR

Model GNE29GMKJES

Near Eagle, CO 81631

Erik

Job Details: 04/29/2024

install sensor pack/test: connect to smartHQ serviceCLEAR F CODES - FF evap running @ 30* FJOB COMPLETE

We serviced a

GE RANGE

Model JBS60RKCSS

Near Eagle, CO 81631

Erik

Job Details: 04/29/2024

outlet miswire - electician needed * see quick picsJOB COMPLETECX not available for signature

We serviced a

GE DRYER

Model GTD33EASK0WW

Near Gypsum, CO 81637

Erik

Job Details: 04/29/2024

install timer and test: set at 25 min/ GOODJOB COMPLETE

We serviced a

GENERAL ELECTRIC M/W OTR

Model PVM9195SF3SS

Near Colorado Springs, CO 80921

David

Job Details: 04/29/2024

Checked microwave and went through operations and testing. Found the PCB is bad. Due to cost cx is going to get a new one.

We serviced a

GE DRYER

Model GFD65GSPN1SN

Near Gypsum, CO 81637

Erik

Job Details: 04/29/2024

install door and hinge asm * see quick picsJOB COMPLETE

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ03

Near Palisade, CO 81526

James R

Job Details: 04/29/2024

"Signed disclaimer. evacuate system,replace dryer and compressor.install lock rings and schrader valve.place system into a vacume.verify system free from leaks, recharger system, vertify operation.all good job complete. Hi side prerssure 65 psi and lo side -6 good and compressor amperage. .89 good. please fill out whirlpool tech satisfaction surveythank you"

We serviced a

BOSCH DISHWASHER

Model SHXM88Z75N/20

Near Monument, CO 80132

Ralph

Job Details: 04/29/2024

"instlled parts and unit checked okay, cust ot monitor"

We serviced a

WOLF WALL OVEN

Model MDD30PM/S/PH

Near Colorado Springs, CO 80921

Ralph

Job Details: 04/29/2024

replaced part and cust approved the repair

We serviced a

SAMSUNG ELECTRON DISHWASHER

Model DW80K5050UG/AA

Near Colorado Springs, CO 80917

Brandon

Job Details: 04/29/2024

"Replaced drain hose, drain pump and water case assy, tested with smart install all checks ok, and installed leak strip"

We serviced a

SAMSUNG RANGE

Model NE63T8111SS/AA

Near Colorado Springs, CO 80916

Mathew

Job Details: 04/29/2024

Replaced shattered cooktop. Test op all okay.

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ1

Near Colorado Springs, CO 80908

Aaron

Job Details: 04/29/2024

"Short in junction box, control and UI console are shorted out, corrected wiring and replaced components, tested unit, working well now. Advised customer of 5 star survey."

We serviced a

SUBZERO REFRIGERATOR

Model 690/F

Near Colorado Springs, CO 80921

Roman

Job Details: 04/29/2024

"Installed new inlet valve, checked it for leaks and made sure it is working properly. Installed new door gasket and dispenser assembly. Tested it and its its working great. Door gasket and door closing properly. Cleaned the condenser coils. Fridge working great."

We serviced a

WHIRLPOOL DRYER

Model WED4815EW1

Near Rio Rancho, NM 87124

Joe

Job Details: 04/29/2024

"Cx complaint. Dryer won't start. Replaced timer, relay and fuses ordered last visit. Tested unit. Unit good to go"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF767SDHZ04

Near Albuquerque, NM 87122

Joe

Job Details: 04/29/2024

Cx complaint. Refrigerator freezing in vegetable drawers. Inspected unit. Installed damper. Tested unit. Unit good to go

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS00

Near Grand Junction, CO 81504

James R

Job Details: 04/29/2024

replace heater for ice maker fill tube.all good job complete.please fill out whirlpool twch satisfaction survey. thank ypou

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS04

Near Pueblo, CO 81006

James

Job Details: 04/29/2024

"Found unit not going into defrost caused by faulty sensor. Needs evap fant/w defrost sensor W11249952 150.74+tax & main board WPW10675033 270.83+tax, sc 149.95, labor 259.95, mps 14.50. Total 730.59. Cust states they have a warranty through All-State. Cust pd 149.95 for sc and will get with All-State to get approval for repair. $149.95 CC Auth# JH33PM"

We serviced a

AGA RANGE

Model GG-E

Near Colorado Springs, CO 80907

Ralph

Job Details: 04/27/2024

REPLACDED REGULATOR AND UNIT CHECKED OKAY

We serviced a

SUBZERO REFRIGERATOR

Model 590

Near Colorado Springs, CO 80907

Ralph

Job Details: 04/27/2024

"INSTALLED PART AND CHARGED THE UNIT, CUST TO MONITOR"

We serviced a

SAMSUNG RANGE - GAS

Model NY63T8751S

Near Colorado Springs, CO 80917

Brandon

Job Details: 04/26/2024

"Replaced both thermostats and main PCB, tested op to 400? after letting unit preheat for 30 minutes, unit keeping set temp, showed customer how to adjust temperature in settings, all checks ok"

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Colorado Springs, CO 80909

Roman

Job Details: 04/26/2024

"Filled the tub and ran the washer, did not see any leaks under the washer and only noticed that water is back flowing in the drain tube without a full tub. Tube and are also looked like water has had overflow in the past. Motor has transmission fluid on it indicating the gear-case is losing oil. Showed cx what sly cord to use and see if she can see it back flowing during a heavy soil cycle. Tightened the agitator screw and motor screw."

We serviced a

WHIRLPOOL FREEZER

Model WZF34X20DW02

Near Colorado Springs, CO 80908

Aaron

Job Details: 04/26/2024

"Removed and replaced control assembly, unit began cooling, monitored unit, and advised customer of survey."

We serviced a

WHIRLPOOL DRYER

Model MED5500FC0

Near Monument, CO 80132

Glenn

Job Details: 04/26/2024

"Found Bad Element -, Obtained one from SSB. WP8544771 $155.07 , Tax $12.72 , MPS $14.50 , Install New Element, All OPS Test:OK ,719 377-0378 , Paid in Full $182.29 + Tip $27.34 = $209.63 , Autho# 9Y4A34"

We serviced a

JENNAIR WALL OVEN

Model JMW2430DS01

Near Monument, CO 80132

Glenn

Job Details: 04/26/2024

"Install New Console, All OPS Test:OKPaid Labor Balance of $229.95 ,719 377 0378 , Autho# PYEW3T"

We serviced a

BEKO MICROWAVE

Model MWDR24100SS

Near Colorado Springs, CO 80908

Jerimiah

Job Details: 04/26/2024

"Unit not heating, found interlock switch bodies out of alignment, adjusted. Unit check ok."

We serviced a

THERMADOR RANGE

Model PRD486WDHU/03

Near Breckenridge, CO 80424

Erik

Job Details: 04/26/2024

install CPM and UI display: callibrate touch pad following the BSH instructions included in parts/ test: ALL burners - GOODgriddle - GOODBOTH ovens - GOOD bake 350*JOB COMPLETECX not available for signature

We serviced a

BOSCH DISHWASHER

Model SHPM78Z54N/22

Near Silverthorne, CO 80498

Erik

Job Details: 04/26/2024

kick plate baffle fell off door - use stick tape to secure while glue setsJOB COMPLETE

We serviced a

BOSCH DISHWASHER

Model SHPM78Z55N/22

Near Colorado Springs, CO 80906

Roman

Job Details: 04/26/2024

"Installed new cover and tested the unit, dw is working great. Cx has said its been working great since last visit."

We serviced a

GE WASHER

Model GFW850SPN1RS

Near Colorado Springs, CO 80921

Glenn

Job Details: 04/26/2024

"Basket / Bearing Check > OK, Suspension OK, Clean Filter Trap, Ran Balance test using 4 large towels > All OPS Test:OK , Informed customer that washer feet are glued to the floor and unit will not budge, suggest soak all 4 feet with warm soapy water to see if they can break free from floor, w/o breaking tile flooring under unit. Paid for both tickets on this ticket (522089 Dryer $89.95 + 129.95 = $219.90 Via Check #244. Autho# XAMCJM"

We serviced a

DACOR RANGE

Model HDPR36S/NG

Near Colorado Springs, CO 80921

Brandon

Job Details: 04/26/2024

"Hinges are bent, door opens past 90?, replaced hinges, all checks ok"