We serviced a
MAYTAG WASHER
Model MHW6630HW0
Near Santa Fe, New Mexico 87507
Jason
Job Details:
01/12/2023
checked unit found control is not supplyong voltage to motor and snutting down SC$140.02LABOR$160.55MISC$17.50CONTROL#W11322883$287.69TX$23.59TOTAL$629.35Auth code:LECH94$140.02
We serviced a
GENERAL ELECTRIC DISHWASHER - BUI
Model GDT550PYR3FS
Near Winter Park, Colorado 80482
Erik
Job Details:
01/12/2023
"connect to SmartHQ diagnosticALERT: failure to drain on at least 1 of the last 5 cycles - check F56 error code diagnostic actionsF56 failure to drain - physically check unit for drain kinks/sump check valve obstructions - none present - replace pumpclear f codes, install pump and test - good"
We serviced a
GENERAL ELECTRIC DRYER
Model GTD33GASK1WW
Near Fraser, Colorado 80442
Erik
Job Details:
01/12/2023
check vent - clearckeck gas connection -ok cable jumper disconnected at switch - re-connect and test - good
We serviced a
GENERAL ELECTRIC RANGE
Model JS645SL6SS
Near Granby, Colorado 80446
Erik
Job Details:
01/12/2023
remove door - replace inner glass
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS04
Near Rio Rancho, New Mexico 87144
Joseph
Job Details:
01/12/2023
installed parts listed. unit tested good. unit is good to go.
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Albuquerque, New Mexico 87109
Larry
Job Details:
01/12/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS04
Near Rio Rancho, New Mexico 87144
Joseph
Job Details:
01/12/2023
installed parts listed. unit tested good. unit is good to go.
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
01/12/2023
"Circulation motor vibrating on back bracket, corrected motor and grommet, tested unit and working well, no leaks.Advised of survey"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, New Mexico 87113
Larry
Job Details:
01/12/2023
CX complaint - Makes loud grinding - Inspected unit and found the shifter was misaligned -mAdjusted shifter and tested good - Unit is good to go
We serviced a
MAYTAG DRYER
Model MEDC215EW1
Near New Castle, Colorado 81647
James R
Job Details:
01/12/2023
replaced heat element and cutout. Heat element was bad. checked vent it was pinched not much air flow. corrected. and connected vent. airflow is better. cycling on and off for heat on all cycles. op's of unit is good. repair complete.Suggested to customer to have venting of home cleaned. Please fill out whirlpool customer satisfaction survey. Thank You.
We serviced a
SAMSUNG WASHER
Model WF45T6000AW/A5 53
Near Yoder, Colorado 80864
Glenn
Job Details:
01/12/2023
"Install New Valve, Ran HASS Diagnostics. >PASSNo Internet, so unshure if report sent."
We serviced a
SAMSUNG RANGE - GAS
Model NX58F5700WS/AA
Near Colorado Springs, Colorado 80926
Brandon
Job Details:
01/12/2023
Replaced ignitor and tested op all okCollected labor $169.95 check Auth# 3H44A9
We serviced a
WHIRLPOOL WASHER
Model MVWB765FW3
Near Peralta, New Mexico 87042
Larry
Job Details:
01/12/2023
Unit needs drain pump - CX doesn not want to bear the cost of repair - Collected $129.95 - Auth-4U9R9H
We serviced a
VIKING DISHWASHER
Model UE9
Near Woodland Park, Colorado 80863
Ralph
Job Details:
01/12/2023
"looks like unit had reg dish soap in the unit, added oil and it desolved the soap, cust to monitor"
We serviced a
GENERAL ELECTRIC DISHWASHER
Model PDT715SBNTS
Near Green Mountain Falls, Colorado 80819
Ralph
Job Details:
01/12/2023
"found a loose screw on the upper part of the tub that had loosined, tightened itg and unit chekced okay"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ00
Near Colorado Springs, Colorado 80920
Kris
Job Details:
01/12/2023
found bad led. installed all ok cx is aware of 5 star survey.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Peyton, Colorado 80831
Kris
Job Details:
01/12/2023
installed ice maker. ran test op all ok unit is working to spec. freezer temp@2.5 ref temp@41.9
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
01/12/2023
"No power coming from the board to drain pump or water inlet valve. Needs board. Board acu w11462458 $262.78Tax $21.55Hc $129.95Labor $169.95Total job $584.2330 day estimateNot home to advise of 5 star surveyCc on file not charged 129.95 as of yet, cx not home for approval"
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Colorado Springs, Colorado 80911
Jim
Job Details:
01/12/2023
"found the timer not advancing, replaced the timer unit test ok"
We serviced a
GENERAL ELECTRIC RANGE
Model JGS760EP3ES
Near Grand Lake, Colorado 80447
Erik
Job Details:
01/12/2023
installed orifice holder and convert to LP -test - good
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Pueblo, Colorado 81003
Jeremy
Job Details:
01/12/2023
"Installed new gearcase and feet. Tested unit. Everything up to munufacturer specs.; (created new UIS, deleted prior attachment to UisID 194146)"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Colorado Springs, Colorado 80917
Kris
Job Details:
01/12/2023
ran test op. unit is getting power. pulled door ui was unplugged from contriol. reseated connections ran test op all ok unit is working to spec. did not talk with cx about 5 star survey. unit was at a business.
We serviced a
SAMSUNG WASHER
Model WA55A7300AE/US
Near Colorado Springs, Colorado 80915
Jonny
Job Details:
01/11/2023
"Installed part, hass passed"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Socorro, New Mexico 87801
Larry
Job Details:
01/11/2023
CX complaint - Right door dragging and scrapping - Adjusted door and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MVW6230HW0
Near Socorro, New Mexico 87801
Larry
Job Details:
01/11/2023
CX complaint - Washer wont start - Inspected unit and found the console won't respont to input - Unit needs new console - Cx doesn't want to bear the cost of repair - COllected $129.95 - Auth-W3KJV4
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW2
Near Edgewood, New Mexico 87015
Jason
Job Details:
01/11/2023
installed parts listed unit checks ok
We serviced a
BEST DOWNDRAFT VENT
Model D49M48SB
Near Monument, Colorado 80132
Jeremy
Job Details:
01/11/2023
Heped JR with downdraft vent
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Colorado Springs, Colorado 80916
Jeremy
Job Details:
01/11/2023
suspension poped out. good now
We serviced a
SAMSUNG WASHER
Model WF50BG8300AVUS
Near Colorado Springs, Colorado 80921
Jeremy
Job Details:
01/11/2023
After being on phone with tech support CX must get unit off of the pedistal and put in serviceable position. Unit slighlty unleveled. CX will need to run unit and relay information. Quoted CX 2x179.95 labor and $129.95 Service fee to remove washer off of pedestal.
We serviced a
KITCHEN AID REFRIGERATOR
Model KRMF706ESS05
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
01/11/2023
"Freezer drawer plastic is warped, front panel to drawer is off and unable to reattach correctly, replaced drawer and tested, working well now. Advised of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW2
Near Colorado Springs, Colorado 80918
Aaron
Job Details:
01/11/2023
"Vibration caused cap to wiggle loose and disconnect from harness, secured and spoke with techline, ran a dlms recalibration on the unit, tested through diagnostics and working well now. Sr #7735222135Advised of 5 star survey"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDM00
Near Colorado Springs, Colorado 80918
Glenn
Job Details:
01/11/2023
"ref- ice maker is not working.Another company already came out a few times, replaced Icemaker, and element? Reseat connections to ice maker, All OPS Test:OK"
We serviced a
SAMSUNG OVEN
Model Nx58m660ws/aa
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
01/11/2023
"Oven igniter reaching 2.8-2.9 ramps, needs consistent 3.2-2.6 to open oven valve. Rest of unit is in good condition. Igniter dg94-00520a $244.50Tax $ 20.05Hc $129.95Labor $159.95Total job $554.4530 day estimateNo return on partsAuth hc 129.95 cc# j4c99j"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
01/11/2023
"Door spring pulling door upwards, adjusted door springs and tested, advised customer. Working well now. Advised of 5 star survey"
We serviced a
WHIRLPOOL M/W OTR
Model WMH32519HW06
Near Colorado Springs, Colorado 80905
Jerimiah
Job Details:
01/11/2023
"Cust had problems with programming light timer, instructions are no help, techline had no information. OTR light functions properly when manually turned on. SR#7735469514. Techline will send videos taken up to engineering. Closing call."
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Pueblo, Colorado 81001
James
Job Details:
01/11/2023
Discussed survey. Installed previous techs ordered parts. All ops test good
We serviced a
SAMSUNG ELECTRIC OVEN
Model NE63T8111SS/AA
Near Pueblo, Colorado 81005
James
Job Details:
01/11/2023
Found Cockroaches under unit and in unit Customer will need to get that sorted with proof of completion or find different servicer per TK. No hass ran
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRFC704FSS02
Near Manitou Springs, Colorado 80829
Ralph
Job Details:
01/11/2023
installed listed parts and cust to monitor the unit
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHZ04
Near Colorado Springs, Colorado 80918
Kris
Job Details:
01/11/2023
installed comp and evap. ran test op unit has full frost pattern all ok.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814WW2
Near Colorado Springs, Colorado 80922
Kris
Job Details:
01/11/2023
installed compressor ran test op unit has full frost pattern and working to spec.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT138FFDW01
Near Colorado Springs, Colorado 80921
Kris
Job Details:
01/11/2023
installed evap and compressor ran test op unit is working to spec.
We serviced a
KITCHENAID MICRO DRAWER
Model KMBD104GSS01
Near Ordway, Colorado 81063
James
Job Details:
01/11/2023
Discussed survey 'Installed ordered parts all ops test good
We serviced a
GE REFRIGERATOR
Model ZISB420DNBII
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
01/11/2023
"fou8nd units ice fill tube frozen, cleared obstruction and informed cust that if unit does not make ice will need a new water valve, cust paid in full autho no. 93UWX9"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80909
Ken
Job Details:
01/11/2023
Washer would not go past sensing. Recalibrate and tested. Discussed fcc survey with customer
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Colorado Springs, Colorado 80909
Ken
Job Details:
01/11/2023
Completing out order. Customer said issue is resolved in precall
We serviced a
GE WALL OVEN
Model CTS90DP3N1D1
Near Colorado Springs, Colorado 80904
Ken
Job Details:
01/11/2023
Installed ui and tested. Unit appears to be working properly advised customer to call us if she has anymore issues
We serviced a
WHIRLPOOL COOKTOP
Model WCG97US6HS00
Near Monument, Colorado 80132
Kris
Job Details:
01/11/2023
installed gas covers all ok. cx is aware of 5 star survey.
We serviced a
SUBZERO REFRIGERATOR
Model BI48SD-0
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
01/11/2023
"todd from subzero is diagnosing dirty electricty, suggested ordering a noise filter and plugging it in...cust paid total bill autho no. V493J3"
We serviced a
VIKING RANGE ELECTRIC
Model VDSC485
Near Colorado Springs, Colorado 80906
Jerimiah
Job Details:
01/11/2023
Installed replacement bake element. Was unable to locate data plate. Charged service call and labor $339.90 CC Auth# 4LC9AT
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model JNM3163RJ5SS
Near Colorado Springs, Colorado 80916
Ken
Job Details:
01/11/2023
Installed cb and tested found loose connection on switch. Remove crimped and replaced. Unit is operating properly
We serviced a
AMANA WASHER
Model NTW4516FW3
Near Colorado Springs, Colorado 80915
Ken
Job Details:
01/11/2023
Installed basket and tested. Advised customer that issue was likely due to over loaded or unbalanced loads and to lighten the loads of heavier items so the machine will last longer.
We serviced a
JENNAIR MICRO DRAWER
Model JMDFS24JL00
Near Colorado Springs, Colorado 80919
Jerimiah
Job Details:
01/11/2023
"Unit not consistently heating, found switches misaligned. Adjusted switches to proper setting. Unit check ok. Disclosed survey to cust fcc."
We serviced a
MAYTAG REFRIGERATOR
Model MFI2269FRZ02
Near Belen, New Mexico 87002
Larry
Job Details:
01/11/2023
Installed IM and tested good - Unit is good to go
We serviced a
FISHER & PAYKEL RANGE
Model RGV2-305NN
Near Colorado Springs, Colorado 80922
Jerimiah
Job Details:
01/11/2023
Installed replacement power relay board. Unit check ok. Charged labor as quoted $199.45 CC Auth# 4X3WCT
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM5
Near Pueblo, Colorado 81005
James
Job Details:
01/11/2023
Installed ordered parts all ops test good.
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC700HPS04
Near Belen, New Mexico 87002
Larry
Job Details:
01/11/2023
Installed reservoir
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Los Lunas, New Mexico 87031
Larry
Job Details:
01/11/2023
Installed gasket and tested good - Unit is good to go
We serviced a
WHIRLPOOL COOKTOP
Model WCG97US6HS00
Near Colorado Springs, Colorado 80924
Jim
Job Details:
01/11/2023
replaced the center burner valve unit test ok
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Los Lunas, New Mexico 87031
Larry
Job Details:
01/11/2023
CX complaint - Washer won't finish cycle - Inspected unit and found the washer aou of calibration - recalibrated and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model WED5050LW0
Near Colorado Springs, Colorado 80904
Jim
Job Details:
01/11/2023
"replaced the drum support wheels, the idler pulley and the drive belt unit test ok T A S"
We serviced a
SAMSUNG DRYER - ELECTRIC
Model DV45K6500E
Near Colorado Springs, Colorado 80911
Jim
Job Details:
01/11/2023
replaced the rear drum support wheels unit test ok
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDT695SSJ2SS
Near Colorado Springs, Colorado 80908
Glenn
Job Details:
01/11/2023
"Installed new Diverter Assy, In the process of re-installing manifold tube, Upper Spray Arm Clip fell off. Supposed to be welded to tub. Entire Tub would need to be replaced to fix unit. Tub Not Available, As confirmed w/ Marcone. Spoke w/ Scott in office, also informed customer."
We serviced a
SAMSUNG DRYER
Model DV40J3000EW/A2
Near Colorado Springs, Colorado 80919
Aaron
Job Details:
01/11/2023
"Motor binding sound, took apart the unit and found zipper tag/debris in the blower wheel, cleared and checked over motor, starting fine now, if problem persists a motor and blower would be needed. Motor and blower assem dc93-00101uTotal parts $380.22Tax $31.18Hc $129.95Labor $169.95Total job $711.30No return on parts30 day estimateAdvised of survey hc 129.95 check auth #p39al4"
We serviced a
MAYTAG WASHER
Model MVWB835DW4
Near Colorado Springs, Colorado 80916
Jim
Job Details:
01/11/2023
"placed unit in normal cycle to test with a towel, unit filled, agitated, spin out and drained unit test ok"
We serviced a
BOSCH DISHWASHER
Model SHVM78Z53N/01
Near Colorado Springs, Colorado 80907
Jim
Job Details:
01/11/2023
"ran unit in rinse , the unit filled , washed and drained unit test ok"
We serviced a
SAMSUNG REFRIGERATOR
Model RF263TEAESG/AA
Near Colorado Springs, Colorado 80923
Brandon
Job Details:
01/11/2023
"Replaced parts and reset ice maker it cycled, hass not compatible, asked cx to complete survey"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7201SR/AA
Near Colorado Springs, Colorado 80923
Brandon
Job Details:
01/11/2023
"Replaced parts and reset ice maker it cycled, hass passed and sent, asked cx to complete survey"
We serviced a
SAMSUNG REFRIGERATOR
Model RF24BB6200QLAA
Near Colorado Springs, Colorado 80916
Jonny
Job Details:
01/11/2023
"Installed new door, took before and after pics, hass passed"
We serviced a
THERMADOR WALLOVEN
Model ME302JP/05
Near Monument, Colorado 80132
Jessie
Job Details:
01/11/2023
- removed screws going to the cabinet. noticed cabinet coming with unit. customer wanted to continue with repair. when pushing unit in the whole bottom of cabinet gave in. needs cabinet work. was able to replace the main bd. handyman connection 719 884 2639.$249.95 autho#we9elj
We serviced a
MAYTAG DRYER
Model MED6230HW2
Near Albuquerque, New Mexico 87121
Joseph
Job Details:
01/11/2023
installed parts listed. unit tested good. unit is good to go.
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Tijeras, New Mexico 87059
Jason
Job Details:
01/11/2023
"checked unit found float plug was not seated, seated plug unit checks ok"
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS0
Near Albuquerque, New Mexico 87123
Jason
Job Details:
01/11/2023
installed heater unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model KDTE104KPS1
Near Albuquerque, New Mexico 87122
Jason
Job Details:
01/11/2023
installed parts unit checks ok
We serviced a
GENERAL ELECTRIC RANGE
Model J2B918SEL2SS
Near Colorado Springs, Colorado 80919
Aaron
Job Details:
01/11/2023
"Control board is sending constant power to the door lock when door switch is engaged. Tried to reset the control board, still not working, needs control board.Control board wb27k10124 $ Part is no longer available from the manufacturer. Auth hc 129.95 #n34c4y"
We serviced a
KITCHENAID RANGE
Model KSDG950ESS3
Near Glenwood Springs, Colorado 81601
James R
Job Details:
01/11/2023
replaced L.F. igniter. first time igniter was faulty sparking inside the electrode. reordered. replaced. test op's good. Please fill out whirlpool customer satisfaction survey. ThankYou.
We serviced a
JENN AIR RANGE
Model JES8850BAS
Near Aspen, Colorado 81611
James R
Job Details:
01/11/2023
display lights up. But no control. removed control panel. called tech line. checked several functions at ribbon of switch control nothing. would need control and UI asy. customer will replace unit. Needs to pay service call. $209.00 Please fill out whirlpool customer satisfaction survey. customer not available to sign.
We serviced a
WHIRLPOOL DRYER
Model WED5620HW2
Near Rio Rancho, New Mexico 87124
Joseph
Job Details:
01/11/2023
installed parts listed. unit tested good. unit is good to go.
We serviced a
FRIGIDAIRE RANGE - ELECTRIC
Model GCRE3060AFA
Near Colorado Springs, Colorado 80918
Jeremy
Job Details:
01/11/2023
Installed new parts. Test ran oven and verified all functions work correctly. All wires tightly fastened. Job complete. Charged $28.05 for cord Auth: JM3Y9Y
We serviced a
SAMSUNG WASHER
Model WA52A5500AC/US
Near Colorado Springs, Colorado 80922
Brandon
Job Details:
01/11/2023
Replaced parts and tested op all ok hass passed and sent asked cx to complete survey
We serviced a
SCOTSMAN ICE MACHINE
Model DCE33PA-1SSD
Near Monument, Colorado 80132
Jessie
Job Details:
01/11/2023
"- replaced bad pump, test op, all ok- leak strip under unit."
We serviced a
SAMSUNG DRYER
Model DV42H5000EW/A3
Near Fountain, Colorado 80817
Jonny
Job Details:
01/11/2023
"Called techline, they say it's a blockage issue didn't recommend parts. Unit too old not hass compatible Autho#Will, get autho# when I have service"
We serviced a
SAMSUNG OVEN
Model NE63A6511SS/AA
Near Colorado Springs, Colorado 80925
Jonny
Job Details:
01/11/2023
"Installed parts, didn't have service to run hass"
We serviced a
WHIRLPOOL OVEN
Model MGR8800FZ2
Near Glenwood Springs, Colorado 81601
James R
Job Details:
01/11/2023
replaced elec control and spark module per Tech Line. Test op's 350 degrees. Let unit cycle several times. lights every time. Operation normal. Checked broil operation as well. working good. Repair complete. Please fill out whirlpool customer satisfaction surv ey. Thank You.
We serviced a
MAYTAG WASHER
Model MVWC465HW4
Near Albuquerque, New Mexico 87112
Jason
Job Details:
01/11/2023
installed control unit checks ok
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KWH0
Near Albuquerque, New Mexico 87112
Jason
Job Details:
01/11/2023
"checked unit found float had been activated, can not locate a leek unit checks ok at this time"
We serviced a
SAMSUNG REFRIGERATOR
Model RF260BEAESR/AA
Near Colorado Springs, Colorado 80909
Jonny
Job Details:
01/11/2023
"Called techline, the recomend case water filter assyCase filter da82-02866a 267.84Tax 21.9614.50 129.95 sfautho#33car3"
We serviced a
SAMSUNG DRYER
Model DV218AEW/XAA
Near Colorado Springs, Colorado 80907
Jonny
Job Details:
01/11/2023
"Installed part, too old for hass, collecting LaborAutho#"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Glenwood Springs, Colorado 81601
James R
Job Details:
01/11/2023
When I arrived unit is running sounds really quiet. Looked at evaporators in Frz and F.F. areas. no frost build up. F.F. evaporator fan running sounds normal. Frz fan running sounds normal. Called tech line did a series of tests. icemaker had no error codes. cycled icemaker. did not kick out any ice. very little in tray. did a fill test filled ok. Tech line recommends sealing cover over icemaker and area where heater and wiring come thru as well. Also the cover with heater sealed. test cycled test for icemaker and fan checked ok. test 56 no error codes. test 45 icemaker fill checked ok. Also did test 4 let go thru all checked ok. please do a satisfaction survey. Thank You.
We serviced a
SAMSUNG WASHER
Model WF45T6000AW/A5
Near Colorado Springs, Colorado 80920
Brandon
Job Details:
01/11/2023
"Cx showed me video of noise but I could not replicate it,checked rotor and stator and weights and suspension all ok tested unit operating with no issues hass passed and sent asked cx to complete survey"
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6200QLAA
Near Colorado Springs, Colorado 80924
Brandon
Job Details:
01/11/2023
"Trips breaker randomly, did not trip for me tech line did troubleshooting with me NDF, recommended cx use outlet and breaker without gfi"
We serviced a
WHIRLPOOL REFRIGERATOR
Model EV250NXTQ 00
Near Colorado Springs, Colorado 80911
Jessie
Job Details:
01/11/2023
"- plugged unit in. compressor took off, pulled evap cover and watch frost pattern form. full frost through evap, pic in quick pics. evap fan good. stuck meter in unit and watched it reach below 5 degrees f. defrost timer is working correctly and heater is good. if problem happens i recommend a new control#WP4-83053-002$129.95 autho#nx9944"
We serviced a
SAMSUNG REFRIGERATOR
Model RF220NCTASR/AA
Near Fountain, Colorado 80817
Jessie
Job Details:
01/11/2023
- unit icemaker is making ice very well. all fans are working well. temps are about 37 and 3. all ok as of now. customer wanted to make sure unit was working well
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9380SR/AA 08
Near Colorado Springs, Colorado 80920
Brandon
Job Details:
01/10/2023
Replaced parts reset ice maker it cycled hass passed and sent asked cx to complete survey
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW08
Near Albuquerque, New Mexico 87121
Joseph
Job Details:
01/10/2023
Installed parts listed. Unit is good to go.
We serviced a
WHIRLPOOL DRYER
Model MED7230HW2
Near Cañon City, Colorado 81212
James
Job Details:
01/10/2023
Discussed survey with cust. Installed preordered part all ops test good.
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Cañon City, Colorado 81212
James
Job Details:
01/10/2023
Discuss survey with customer. Installed preordered parts testing operations all check OK
We serviced a
BOSCH DISHWASHER
Model SHE55M06UC/50
Near Divide, Colorado 80814
Ken
Job Details:
01/10/2023
Dishwasher is not heating and repeats the cycle when it ends. Called bsh tech part is nla cb pn 676963 is what is needed.
We serviced a
WHIRLPOOL DRYER
Model WED5620HW0
Near Pueblo West, Colorado 81007
James
Job Details:
01/10/2023
Installed ordered part all ops test good. Collected 129.95 $129.95 CC Auth# K9MK9M
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS1
Near Colorado Springs, Colorado 80924
Glenn
Job Details:
01/10/2023
Customer indicates Range has already been fixed!? They also indicated that they have tried to cancel this appt. 3X?!
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Albuquerque, New Mexico 87107
Larry
Job Details:
01/10/2023
Installed paerts listed and tested good - Unit is good to go