We serviced a
SAMSUNG RANGE
Model NSE6DG8100SR
Near Fountain, Colorado 80817
Mathew
Job Details:
05/08/2026
Replace parts. Test op. All okay.
We serviced a
WHIRLPOOL RANGE
Model WFE770HFZ
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
05/08/2026
Replace element. Test op. All okay.
We serviced a
GE WASHER
Model GFW550SSNWW
Near Sandy, Oregon 97055
Austin
Job Details:
05/08/2026
"5/8/26 BA: removed and replaced main mother board assembly and door latch. Programmed unit to proper settings and started a quick wash. Unit is now operating without shutting off after a few seconds. Customer approved, service is complete."
We serviced a
SAMSUNG WASHER
Model WF45T6000AW/A5
Near Monument, Colorado 80132
Brandon
Job Details:
05/08/2026
"Found no signs of water leaking from the unit, ran tests and no leaks checked all possible locations for leaks and connections, drain is next to unit i suspect possible plumbing issue informed cx to monitor, leak strip down hass passed"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PWO
Near Grand Junction, Colorado 81501
Clint
Job Details:
05/08/2026
Customer signed disclaimer and recieved parts ordered. Installed control and actuator programmed board unit ran perfectly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3536SZ01
Near Palisade, Colorado 81526
Clint
Job Details:
05/08/2026
Customer signed disclaimer and recieved part sent to them. Installed new water valve and unit didn't leak and filled ice tray. Water dispenser worked perfectly. PLEASE TAKE TECH SURVEY THANKS CLINT.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ4
Near Pueblo West, Colorado 81007
James
Job Details:
05/08/2026
"Found unit with small amount of water in drip tray replaced preordered parts. Also found unit not level, leveled unit, reinstalled tested ops all ckok left litmus. Mentioned survey"
We serviced a
BOSCH DISHWASHER
Model SHE3ADF5N/01
Near Leadville, Colorado 80461
Erik
Job Details:
05/08/2026
LOWES INSTALLER NEVER INSTALLED HIGH LOOP AT DRAINNSTALL HIGH LOOP DRAIN AND SECURE/ TEST: PASSJOB COMPLETE
We serviced a
SAMSUNG WASHER
Model WD53DBA900HZA1
Near Colorado Springs, Colorado 80908
Brandon
Job Details:
05/08/2026
"Error 5c6 in hass, removed all lint from vent chamber, replaced drain pump, called tech supoort to document because of redo, followed service tip, tested operation all checks ok hass passed"
We serviced a
WHIRLPOOL DRYER
Model WED4105SW1
Near Colorado Springs, Colorado 80907
David
Job Details:
05/08/2026
"Checked dryer, good air flow from dryer, heater is cycling as it should, shortened vent hose to reduce restrictions to vent stack to roof, seams to be better. Cx to monitor. Mentioned surveys."
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD706MPS00
Near Colorado Springs, Colorado 80904
David
Job Details:
05/08/2026
"Replaced reservoir, tested, good flow, placed leak strip."
We serviced a
PROFILE WASHER/DRYER COM
Model PFQ97HSPV0DS
Near Bend, Oregon 97702
Levi
Job Details:
05/08/2026
"Customers complaint is that overtime they have noticed that drying is taking longer than normal. Upon initial inspection I found the air filter was clogged with a residue and when I took it to the kitchen sink to test it, water flow is heavily restricted through it indicating that it needed to be cleaned. I clean the filter with Dawn dish soap and a brush and decreased it pretty good and then on the final water test, water flowed through it unrestricted. I am fairly certain that is what the problem is at least it is a good start. I'm going to ask the customer to use it and go from there. All other functions appear to be operating normally."
We serviced a
WHIRLPOOL DRYER
Model WED6150PB0
Near Grand Junction, Colorado 81505
James R
Job Details:
05/08/2026
Signed disclaimer. Replaced control all is working. Checked function of auto dry cycle. Put so clothing in unit to check sensor after abit shows wet so it does work. On this setting cloths have to touch the sensing bars in order to sense the dryness of the items or it will run awhile and shut off prematurely. Checked temp 145 degrees ok. Checked on timed dry no cloths 165 degrees so is heating as designed. Do not overlpoad cloths need to tumble circulate in order to dry properly. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ11
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
05/08/2026
Replace parts. Test op. All okay.
We serviced a
GE WASHER
Model GTW585BSV3WS
Near Grand Junction, Colorado 81504
Sean
Job Details:
05/08/2026
Verified information customer signed disclaimer.Removed the control panel and loosened the hing screws. Removed the old door and lever.Assembled the new door and installed the new lever.Installed the new door and tested it. Door is operating as designed by factory.Thank you.Please fill out a technician survey..
We serviced a
PROFILE DRYER
Model PTD70EBPT1DG
Near Grand Junction, Colorado 81503
Sean
Job Details:
05/08/2026
Verified the information customer signed disclaimer.Tested the unit and it was making a grinding noise.Removed the top panel.And removed the door panel. And found that there was debris caught cleaned the track and adjusted the felt pad.Reassembled the unit. Tested and found that the unit is now operating as designed by factory.Thank you please go online to our website and fill out a technician survey.Your technician.Sean....
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRMS2773AF01
Near Colorado Springs, Colorado 80919
Charles
Job Details:
05/08/2026
"Replaced user interface, overlay and paddle. Tested all functions."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5300SRAA
Near Merlin, Oregon 97532
Chris
Job Details:
05/08/2026
Replaced the step valve and drier filter. Vacuumed down and recharged the system. My low side pressure never left deep Vacuum. I called TS they said to replace the drier filter again and recharge the system. Called TS again for the 3rd time. They had me vacuum it out again for 25 minutes the flush the system with nitrogen 350 psi to flush it. I recharged the system and got the same condition. Called TS again and they gave me this clame number 7006839274.
We serviced a
MIELE COFFEE MACHINE
Model CVA6805
Near Colorado Springs, Colorado 80919
Charles
Job Details:
05/08/2026
Replaced main board and power control board. Completed update set language and time. Made a cup of coffee. Collected labor $1079.80 autho C3YA3C
We serviced a
GENERAL ELECTRIC WASHER
Model PTW700BPT0DG
Near Mesa, Colorado 81643
Clint
Job Details:
05/08/2026
Customer signed disclaimer and recieved parts ordered. Installed new lid and lid lock assembly. Had to put model /serial number sticker on the side of the unit it wouldn't stick to the plastic. Ran unit and it looks ked and functioned properly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Roseburg, Oregon 97471
Chris
Job Details:
05/08/2026
Replaced the drier filter and evaporator cover. The evaporator is starting to get frost.
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Medford, Oregon 97504
Kyle
Job Details:
05/08/2026
"Found water pressure weak or no existent at the dispenser, checked water pressure in rear of unit, great pressure from house side. Replaced case filter assembly and tested. Unit is operating ad intended. Purged 20 cups of water from system and test cycled ice maker assemblies."
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ5
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
05/08/2026
Arrived and cx complaint of center burner not lighting right. Installed new burner and electrode sent. Unit is functioning now as designed informed cx of review process.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFC2353AF
Near Pueblo, Colorado 81006
Domingo
Job Details:
05/08/2026
Replaced fan with defrost heater and defrost thermostat test it and test it good check door for seal told cx about surgery
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
05/08/2026
Arrived and removed old parts. Installed new parts. Recalibrate washer. Tested washer on quick cycle. Unit is functioning now as designed. Informed cx of review process.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC3
Near Los Lunas, New Mexico 87031
Larry
Job Details:
05/08/2026
Installed valve and tested good - Unit is good to go - Survey mentioend
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Los Lunas, New Mexico 87031
Larry
Job Details:
05/08/2026
CX stated she has an extended warranty - Advised cx to contact her warranty company and get another dispatch
We serviced a
MAYTAG DRYER
Model MED4005SW0
Near Los Ranchos de Albuquerque, New Mexico 87107
Larry
Job Details:
05/08/2026
CX complaint - Dryer making loud clunking and not heating - Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS03
Near Albuquerque, New Mexico 87120
Larry
Job Details:
05/08/2026
CX complaint - Not making ice - Inspected unit found the IM failed - Installed psrts listed and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL STACK UNIT
Model WFW5605MW
Near Albuquerque, New Mexico 87120
Larry
Job Details:
05/08/2026
Cannot unstack unit - Ticket is being reassigned by Assurant
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSN2610AF0
Near Jacksonville, Oregon 97530
Kyle
Job Details:
05/08/2026
"Removed and replaced evap fan and fan blade, verified repairs, unit is operating as intended. Set temps to customer recommended temps."
We serviced a
WHIRLPOOL DRYER
Model WED6150PW0
Near Grand Junction, Colorado 81506
James R
Job Details:
05/08/2026
Signed disclaimer. Replaced heat element and cutoff. Test run unit is operating as designed. Vent disconnected. Temp timed dry 155 degrees good. Can tell that venting is restricted somewhat. Customer needs to have cleaned to be more efficient. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Grand Junction, Colorado 81501
James R
Job Details:
05/08/2026
Signed disclaimer. Replaced control per sp w11766193 special project s153eb Calibrated new control then run thru a service test is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Grand Junction, Colorado 81504
James R
Job Details:
05/08/2026
Signed disclaimer. Replaced control then run thru a service test is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
05/08/2026
Installed control board ran test and calibration runs all ok
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
05/08/2026
Installed control board ran test and calibration runs all ok
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1835VWC
Near Tillamook, Oregon 97141
Nathan
Job Details:
05/08/2026
Replaced failed timer Tested Advised of survey
We serviced a
SAMSUNG MICROWAVE
Model ME16A4021AS/A2
Near Colorado Springs, Colorado 80927
Brandon
Job Details:
05/08/2026
"Broken handle, replaced door and tested operation all checks ok"
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Colorado Springs, Colorado 80923
Brandon
Job Details:
05/08/2026
"Replaced drier and repaired leak, charged unit tested operation all checks ok hass passed"
We serviced a
MAYTAG DRYER
Model MED5630HW2
Near Albuquerque, New Mexico 87109
Jason
Job Details:
05/08/2026
Installed parts listed. ran timed dry cycle unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Albuquerque, New Mexico 87122
Jason
Job Details:
05/08/2026
Installed grates unit checks ok. uploaded pic of new grates installed. spoke to cx about review
We serviced a
LG REFRIGERATOR
Model LFX25991ST.ASTCNA0
Near Pueblo West, Colorado 81007
Domingo
Job Details:
05/08/2026
Replaced ice maker that lg sent to cx test it and it worked it turned and drop water
We serviced a
WHIRLPOOL DRYER
Model WED72HEDW0
Near Albuquerque, New Mexico 87122
Jason
Job Details:
05/08/2026
Installed parts ran timed dry cycle unit operation checks ok. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MFW7020RU0
Near Albuquerque, New Mexico 87111
Jason
Job Details:
05/08/2026
Installed pressure sensor. ran whole quick wash cycle unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87120
Larry
Job Details:
05/08/2026
CX complaint - Drain pump keeps running - Inspected unit and found F3E1error - Replaced control and tested good - Unit is good to go - Survey mentioned
We serviced a
FISHERPAYKEL DISHWASHER
Model DD24DT4NX9
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
05/08/2026
"Spoke with techline and tested all functions of unit ok. Unit is working properly but needed to explain to customer how unit dries dishes and how to use unit more effectivly like loading,using higher temp settings, running hot water at sink before use. RK"
We serviced a
THERMADOR DOUBLE WALL OVEN
Model MEDMC301WS/04
Near Colorado Springs, Colorado 80919
Ryan
Job Details:
05/08/2026
Replaced microwave turntable and tested operation ok. Replaced seized rack in oven cavity. All now working properly. RK
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
05/08/2026
"Found clothing blocking motor, removed and tested operation all checks ok hass passed"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFHB2750TS6
Near Jacksonville, Oregon 97530
Kyle
Job Details:
05/08/2026
"Replaced ice maker assembly, old assembly had bits of stuff in the ice cups themselves. Dumped out all old ice, advised customer 48-72 hours for full bucket of ice."
We serviced a
WOLF MICROWAVE
Model MD24TE/S
Near Colorado Springs, Colorado 80906
Charles
Job Details:
05/08/2026
Replaced right side switch holder and switches
We serviced a
THERMADOR WALL OVEN
Model SMW272
Near Colorado Springs, Colorado 80906
Charles
Job Details:
05/08/2026
"No bake, element ohm ok. Relay board no longer available. Service fee $169.95 paid autho 9JHL9J"
We serviced a
SUBZERO REFRIGERATOR
Model 632/0
Near Colorado Springs, Colorado 80903
Charles
Job Details:
05/08/2026
Replaced ice maker and both refrigerator door switches.
We serviced a
THERMADOR FREEZER
Model T18ID80NLP/42
Near Pueblo, Colorado 81001
James
Job Details:
05/08/2026
Installed ordered part tested ops all ckok left litmus. Filter head no longer leaks and dispenser is flowing as designed collected 295.95 $295.95 CC Auth# JN44CN
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED2VHEXTB01
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
05/08/2026
Arrived and cx complaint of icemaker not working. Found the dhut off arm had been dis lodged. Re attached arm wire snd unit is functioning now as designed.
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SR/AA
Near Colorado Springs, Colorado 80910
Mathew
Job Details:
05/08/2026
"Remove and Evac old comp. Install comp, drier, stub. Pull into vac. Leak check. Charge to spec. 75g. Pressures good, temps falling. All ok. Cx to monitor temps."
We serviced a
THERMADOR REFRIGERATOR
Model T36BT920NS/04
Near Breckenridge, Colorado 80424
Erik
Job Details:
05/08/2026
FALSE ALARM - FF CAVITY SET AT 36 AND HOLDING TEMPCX USED A THERMOMETER TO CHECK TEMPS WITH NO FOOD OR LIQUIDS IN FF CAVITYGLASS OF WATER AFTER 24 HOURS WILL REFLECT PROPER TEMPSJOB COMPLETECALL BSH TAG: DOCUMENT CALL AND CONFIRM ALL VITALS NOMINAL
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Colorado Springs, Colorado 80922
David
Job Details:
05/08/2026
"Replaced motor and blower wheel, ensured potential vibration points are tight, found a couple of screws that were not completely tightened. Tested and is operating correctly, normal sounds for this model."
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
05/08/2026
Installed control board ran test and calibration runs all ok
We serviced a
WHIRLPOOL DRYER
Model MEDB200VQ0
Near Fountain, Colorado 80817
Carlos
Job Details:
05/08/2026
Installed heater ran tests runs all ok. Told of survey
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
05/08/2026
Arrived and cx complaint of dryer turning off after just a few minutes of running on auto cycle. Runs fine on timed. Did not call techline while at hone. This complaint is totally different than other svc visits. Replaced parts sent to cx. Tested unit. Seems to be functioning as designed now.
We serviced a
FRIGIDAIRE FREEZER UPRIGHT
Model FFUE2022AWG
Near Grand Junction, Colorado 81505
Sean
Job Details:
05/08/2026
Verified the unit information customer signed disclaimer..Openen the freezer and removed the shelves. Removed the back panel and unhooked the temp control.Installed the new temp control and reassembled the unit.Started the freezer and watched the compressor start up.I waited for the fan motor to come on. And the temp to start dropping.The unit started and operating as designed by factory.Thank you please go online to our website and fill out a technician survey.And pleaseGive the unit 24 hours to stabilize before using it.
We serviced a
WHIRLPOOL DRYER
Model WED8000DW4
Near Peyton, Colorado 80831
Aaron
Job Details:
05/08/2026
"Heating element grounded, shorted thermostat and thermal fuse, removed and replaced components, tested unit, working and heating well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDTS7024RZ0
Near Peyton, Colorado 80831
Aaron
Job Details:
05/08/2026
"Drain hose connected to garbage disposal, line blocked, corrected and tested unit through diagnostics, working well now, advised customer of usage, recommend using rinse aid for heated dry. Advised customer of situation and survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model GS6NBEXRQ01
Near Peyton, Colorado 80831
Aaron
Job Details:
05/08/2026
"Removed and replaced ice maker assembly, calibrated to optics, completed harvest cycle, needs time to cool. Total due was previously paid."
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS3
Near Gresham, Oregon 97080
Jesse
Job Details:
05/08/2026
May/8/26 9:26 contacted client eta 45 minsReplaced parts and tested. No issues found. Core board is ready for return
We serviced a
SUBZERO REFRIGERATOR
Model BI42SDSTH
Near Portland, Oregon 97223
Jesse
Job Details:
05/08/2026
"(JG) 11:13am may/8/2026 contacted client notified eta 12:00 Clients concern is the bottom three drawers and 1 drawer above are freezing veggies. Verified frozen veggies and documented. Hooked unit up to diagnostics module no active errors, unit is set to proper temps. Verified the ice damper isnt stuck open, no heavy frosting on food facing side of cap cover.checked with tech support who states that the unit may have poor air circulation due to unit being stored with too many items.Showed client user manual in unit that has storage location indicators & recommend storing less items in shelfs for better air flow"
We serviced a
PROFILE REFRIGERATOR/TOP
Model PVD28BYNHFS
Near Grand Junction, Colorado 81507
Sean
Job Details:
05/08/2026
Verified information customer signed disclaimer Unplugged the door and removed the pcba board and installed the new one.Removed the door ice maker board and replaced it with the new one.Reassembled the unit and restored the power.Tested the button good everything is operating as designed.Thank you .Please fill out a technician survey.
We serviced a
MONOGRAM REFRIGERATOR
Model VIS420NNB11
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
05/08/2026
Operating noise is normal. Customer noticing speed increase from variable speed compressor. RK169.95AUTH 49XCE3
We serviced a
LG COOKTOP
Model CBGJ3023D.BBDELNA
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
05/08/2026
"There is nothing wrong with the unit itself, but flames blowing out when cabinet doors are opened is caused by vacuum/draft. Builder needs add a vent inside of cabinets.RK"
We serviced a
SUBZERO REFRIGERATOR
Model CL4250SID/O
Near Grand Junction, Colorado 81507
Sean
Job Details:
05/08/2026
Verified the unit information customer signed disclaimer.Checked the unit and found the freezer was frozen up.Put the unit into service mode and tested the components.Ran the unit on a defrost cycle.The unit did run the defrost and melted the ice.Checked the units door gasket it is good.Checked the ice maker. Found the ice maker power cord wrapped around the fill hose and causing it to drip over and freeze up .Adjusted the wires so they where run differently .Reassembled the unit.The freezer is cooling down.Ice maker will start when the freezer gets to temperature.Thank you.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
05/08/2026
Installed sump assembly runs all ok left leak strip
We serviced a
WHIRLPOOL WASHER
Model CAE2795FQ2
Near Frisco, Colorado 80443
Antonio
Job Details:
05/08/2026
Installed new cntrl in washer then ran a cycle for proper operation and unit is working properly also advised cx of whlp survey
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
05/08/2026
Installed control board ran tests and calibration runs all ok
We serviced a
DACOR REFRIGERATOR
Model DRR36980LAP
Near Monument, Colorado 80132
Ryan
Job Details:
05/08/2026
Found sealed system with massive restriction with high side at 200 psi. Sealed system has been worked on several times over the past year and is on the 4th compressor. This is not something we should get into. Customer happy with some kind of answers and is going to buy a new one. RK179.95AUTH 33CRX4
We serviced a
MARVEL ICE MACHINE
Model MLCP215-SGO1A
Near Colorado Springs, Colorado 80908
Ralph
Job Details:
05/08/2026
replaced listed part and unit checked okay
We serviced a
GE GAS RANGE
Model GGF500PV2SS
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
05/08/2026
"Control panel bracket missing screw, secured and tested operation all checks ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Rifle, Colorado 81650
James R
Job Details:
05/08/2026
Printed labels took pics ready to send.
We serviced a
WHIRLPOOL RANGE
Model WFC315S0JS4
Near Redmond, Oregon 97756
Richard
Job Details:
05/08/2026
Installed new control cycle tested unit all tested fine at this time
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Silverthorne, Colorado 80498
Erik
Job Details:
05/08/2026
ACCESS WITH DOOR CODE INSTALL/ TEST: PASSMODE SHIFT FROM SPIN TO AGITATE AND ALL OPERATING NOISE IS NOMINALCX NOT AVAILABLE FOR SIGNATURE
We serviced a
MIELE COFFEE MACHINE
Model CVA7845
Near Colorado Springs, Colorado 80908
Charles
Job Details:
05/07/2026
"Cannot install brew unit, drive gear not aligned, enter diagnostics and reset gear drive to home position. Installed brew unit and made a cup of coffee."
We serviced a
SAMSUNG WASHER
Model WD53DBA900HZA1
Near Colorado Springs, Colorado 80921
Mathew
Job Details:
05/07/2026
Replace dryer base. Leak check. Test op. Unit working as expected. All okay.
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Peyton, Colorado 80831
Mathew
Job Details:
05/07/2026
Replace crisper shelf. Test op all okay.
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Colorado Springs, Colorado 80924
Mathew
Job Details:
05/07/2026
Leveled unit. Test op. All okay. Collect svf $149.95.
We serviced a
KITCHENAID DISHWASHER
Model KDTF924PPS00
Near Redmond, Oregon 97756
Richard
Job Details:
05/07/2026
"Installed new inlet, water valve and hose cycle tested unit. Ill checks good at this time."
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Los Alamos, New Mexico 87544
Tye
Job Details:
05/07/2026
Arrived and cx complaint of gas smell. found no gas leaks. Cx is smelling lack if oxygen due to oven burning at high altitude. Nothing wrong with range. No further issues noted.
We serviced a
GE REFRIGERATOR
Model GSE25GYPFS
Near Colorado Springs, Colorado 80925
Ralph
Job Details:
05/07/2026
"cust cfomplaint that unit was leaking from the dispenser, ran severaslb glasses of ewater from the dispenser and saw no signs of leaking, also cycled ice mkr andsaw no signs as well, spooke with cust and told hm my findibgs"
We serviced a
KITCHENAID DISHWASHER
Model KDTE234GPS1
Near Winter Park, Colorado 80482
Antonio
Job Details:
05/07/2026
Installed new element thermoster and control then ran a cycle for proper operation unit is working properly
We serviced a
KITCHENAID DISHWASHER
Model KDTS324SPS0
Near Winter Park, Colorado 80482
Antonio
Job Details:
05/07/2026
Installed new panel unit looks great
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW
Near Santa Fe, New Mexico 87505
Tye
Job Details:
05/07/2026
Arrived and removed failed parts. Installed new parts. Recalibrate washer. Checked operation on quick cycle. Unit is functioning now as designed. Informed cx of review process.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Fraser, Colorado 80442
Antonio
Job Details:
05/07/2026
Installed new icemaker and then cycled icemaker and unit is working properly
We serviced a
JENN-AIR WALL OVEN
Model JMW2427LL03
Near Tabernash, Colorado 80478
Antonio
Job Details:
05/07/2026
Installed new ui panel then turned unit on and heated oven to 350 degrees and a cup of water for proper operation and unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Santa Fe, New Mexico 87505
Tye
Job Details:
05/07/2026
Arrived and removed failed parts. Installed new parts. Recalibrate washer. Tested unit on quick wash. Washer is functioning now as designed. Informed cx of review process.
We serviced a
AMANA DISHWASHER
Model ADFS2524RW0
Near Trinidad, Colorado 81082
James
Job Details:
05/07/2026
Found unit with f2e1 error indicating stuck key on main board. Replaced with preordered control. Tested ops all ckok mentioned survey
We serviced a
WHIRLPOOL W/D STACKED UNIT
Model WETLV27HW3
Near Bend, Oregon 97701
Levi
Job Details:
05/07/2026
"Replace control board, performed recalibration cycle and tested, all checks okay"
We serviced a
WHIRLPOOL RANGE
Model WFC150M0JS4
Near Trinidad, Colorado 81082
James
Job Details:
05/07/2026
Found loose wire at burner connection causing odd behavior secured and tested all ops test good
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Rio Communities, New Mexico 87002
Larry
Job Details:
05/07/2026
Installed housing and tested good - Unit is good to go
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC136RPS00
Near Granby, Colorado 80446
Antonio
Job Details:
05/07/2026
Installed new icemaker and then cycled icemaker unit is testing good
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Santa Fe, New Mexico 87507
Tye
Job Details:
05/07/2026
Arrived and removed failed control. Installed new control. Unit should be back to normal. Informed cx of review process
We serviced a
WHIRLPOOL W/D STACKED UNIT
Model WETLV27HW3
Near Bend, Oregon 97701
Levi
Job Details:
05/07/2026
"Replace control board, performed recalibration cycle and tested, all checks okay"
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Bend, Oregon 97701
Levi
Job Details:
05/07/2026
"Replace control board, performed recalibration cycle and tested, all checks okay"