We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Peyton, Colorado 80831
Aaron
Job Details:
06/04/2026
"F5E3 error code upon arrival, control is not sending power, replaced control and latch, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
DACOR VENT HOOD
Model IVSR2
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
06/04/2026
$229.95 CC Auth# WJ3C34Install part. Test op. All okay.
We serviced a
BOSCH DISHWASHER
Model SHP78CM4N/34
Near Granby, Colorado 80446
Erik
Job Details:
06/04/2026
ACCESS THROUGH GARAGE DOORREPLACE RAIL SYSTEM ON UPPER RACK ASMJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
KITCHENAID DISHWASHER
Model KDPS324SPS0
Near Carbondale, Colorado 81623
Clint
Job Details:
06/04/2026
Customer signed disclaimer and recieved door lock ordered.Installed new door lock and mounted the dishwasher level. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
MAYTAG WASHER
Model MHW8630HC4
Near Santa Fe, New Mexico 87501
Tye
Job Details:
06/04/2026
Arrived and cx complaint of not working right. Takes way too long to finish cycles. Keeps adding time. I had cx start washer on quick cycle 20 minutes b4 I arrived. When i arrived washer was still st 32 minutes should have been almost completed. No clothes were in washer. I had just replaced the control and user interface. I recommend replacement of control again. Cx is not happy with more parts. I honestly don't know if s new control will fix issues. Washer seems to be un repairable. And should be exchanged.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW1
Near Bend, Oregon 97702
Richard
Job Details:
06/04/2026
"Install new sump assembly cycle tested unit tested good this time. No leaks at time of repair,job complete"
We serviced a
KITCHENAID DISHWASHER
Model KDTM804KPS3
Near Santa Fe, New Mexico 87506
Tye
Job Details:
06/04/2026
Arrived and cx complaint of not cleaning properly. Filled dw when 1st arrived it had way too many suds. Found cx using cascade plus with dawn. Informed cx not to use that detergent. And add vinegar to wash. He is also on a well which can contribute to cloudy glasses. Recommend soap without dawn and lemishine added to dw every load. And getting water hot to faucet before starting dw. Cx is happy with diagnosis.
We serviced a
MAYTAG WASHER
Model MVW6230RHW3
Near Central Point, Oregon 97502
Kyle
Job Details:
06/04/2026
Replaced worn through pressure switch tube. Tested machine in quick wash cycle. Unit is operating as intended.
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Albuquerque, New Mexico 87105
Larry
Job Details:
06/04/2026
Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
GE DISHWASHER
Model GDF535PSR7SS
Near Peyton, Colorado 80831
Earl
Job Details:
06/04/2026
"Customers complaint unit is leaking water in the front left corner i found the tech manual's corner stuck inside soaking the water, letting it run underneath the door and dripping off the side."
We serviced a
SAMSUNG MICROWAVE
Model ME21DG6300SRAA
Near Colorado Springs, Colorado 80927
Mathew
Job Details:
06/04/2026
"Replace control. Test op, unit working as expected. All okay."
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Belen, New Mexico 87002
Larry
Job Details:
06/04/2026
Cx complaint - Start button not working - Inspected unit and found the control failed - Replaced control and tested good - Unit is good go
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC236SPS04
Near Bend, Oregon 97701
Richard
Job Details:
06/04/2026
Installed new icemaker cycled tested all checks. Good at this time.
We serviced a
SUB-ZERO FREEZER
Model 690F
Near La Pine, Oregon 97739
Levi
Job Details:
06/04/2026
"While looking for failure of freezer compressor, found that connector to comp was not fully engaged. Properly secured the connection and nothing else appears to be wrong with unot"
We serviced a
WHIRLPOOL RANGE
Model WCE55US0HB01
Near La Pine, Oregon 97739
Levi
Job Details:
06/04/2026
Replaced duel element and fr Infiniti switch. Test good
We serviced a
PROFILE REFRIGERATOR
Model PVD28BYNDFS
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
06/04/2026
"Customer had vegtables freezing in convertable drawer. Spoke with text line and veggies should not be in this drawer and only in crisper in ff section. Converatble drawer get cold air from freezer and is make for drinks , wine, cheese. RK169.95AUTH 9JJ3A9"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87123
Jason
Job Details:
06/04/2026
Installed control ran calibration and qwick wash cycles. unit operation checks ok. spoke to cx about review
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS10
Near Colorado Springs, Colorado 80908
Jason
Job Details:
06/04/2026
"Replaced gaskets and dampner control, tested unit and confirmed operation, unit repaired, spoke to customer about survey"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ3
Near Colorado Springs, Colorado 80921
Jason
Job Details:
06/04/2026
"Replaced UI and door lock, tested unit and adjusted drain line, unit repaired. Spoke to customer about survey"
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, Colorado 80921
Jason
Job Details:
06/04/2026
"I replace the diode wire harness and the main control, tested on a sensor cycle with a wet paper towel to verify that it was working in the consumer mode, spoke to customer about the survey unit repaired."
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HB10
Near Colorado Springs, Colorado 80919
Jason
Job Details:
06/04/2026
Replace the magnetron and capacitor first and tested and confirmed operation as main control is not needed. Expect a customer about the survey unit repaired.
We serviced a
SAMSUNG DRYER
Model DV42H5200EF TO//A3
Near Colorado Springs, Colorado 80921
Jason
Job Details:
06/04/2026
"Replace the drive belt and lubricated all of the bearing shafts for the roller wheels, tested unit and confirmed operation, unit repaired"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS07
Near Colorado Springs, Colorado 80920
Aaron
Job Details:
06/04/2026
"Removed and replaced main, Orion, and UI control, tested fans and compressor in diagnostics, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WALL OVEN
Model WOED5030LZ01
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
06/04/2026
"Convection fan blade slightly bent and ticking, corrected and tested multiple times, verified by customer , working well now. Advised customer of situation and survey."
We serviced a
THERMADOR REFRIGERATOR
Model T30IR905SP/09
Near Grand Lake, Colorado 80447
Erik
Job Details:
06/04/2026
INSTALL POWER BOARD AND LEDS/ POWER ON AND TEST: PASSLABOR $239.95 PAID autho# V99XL9JOB COMPLETE
We serviced a
WHIRLPOOL REFRIGERATOR
Model WZF34X20DW06
Near Edgewood, New Mexico 87015
Jason
Job Details:
06/04/2026
Installed control box unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW4300SW0TEC
Near Colorado Springs, Colorado 80919
Torrey
Job Details:
06/04/2026
Removed and replaced all 4 shocks. Ran a factory calibration. Ran a test cycle to check all functions. All tested good.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AFM
Near Pueblo, Colorado 81005
James
Job Details:
06/04/2026
Installed ordered parts tested ops all ckok Qt
We serviced a
WOLF RANGE
Model DF606F
Near Colorado Springs, Colorado 80908
Ryan
Job Details:
06/04/2026
Unit working fine at this time but most burners were loose and front right was slow to light. Tightened all burners and cleaned of front right burner ignitor. Tested operation and all now working properly. RKAUTH LR4T4N
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF707ESS01
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
06/04/2026
"REPLACED FAN ASSEMBLY WITH THE EVAP SENSOR, CUST TO MONITOR...AUTHO NO. 9V4EVR"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS07
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
06/04/2026
"Installed inverter, control board and thermistors. Inverter was giving start fail code therefore replaced, compressor began running along with fans. Cx will observe."
We serviced a
ASKO DISHWASHER
Model DFI565XXLU|740100
Near West Linn, Oregon 97068
Jesse
Job Details:
06/04/2026
"(JG) June 4th , 10am called client informed eta 60 mins obtained tech sheet from manufacturer via email. Installed and made adjustments. Tested rack with different force. Stays on rail with out issue . Showed client unit functional."
We serviced a
WHIRLPOOL DRYER
Model WED5050LW1
Near Colorado Springs, Colorado 80916
David
Job Details:
06/04/2026
"Heater burned-out, replaced heater and cut off. Tested and is heating good. Good air flow."
We serviced a
GE RANGE HOOD
Model UVW8301SL2SS
Near Colorado Springs, Colorado 80925
David
Job Details:
06/04/2026
"Checked range hood, there is a bracket on the bottom of the blower that needed to be removed before instalation, and clearly state's it. Fan motor is operating correctly, just not getting air flow. Talked to cx, they are going to confirm duct work is open."
We serviced a
SAMSUNG REFRIGERATOR
Model RF265BEAESR/AA
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
06/04/2026
"FF doors havent closed in 4 years, extreme buildup of ice behind evap. cover. Defrosted everything and made sure all components worked after. RKLabor 239.95S/C 149.95Total 389.90AUTH 43W4PF"
We serviced a
GE WASHER
Model PTW600BSR1WS
Near Colorado Springs, Colorado 80911
Charles
Job Details:
06/04/2026
"Water dripping from hot water inlet hose at valve and running down back of washer, tighten hose, and ran rinse cycle with no leaks."
We serviced a
LG REFRIGERATOR
Model LMX25981ST
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
06/04/2026
CUST TO REPLACE THE UNIT...AUTHO NO. W4HMY3
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Colorado Springs, Colorado 80909
Ralph
Job Details:
06/04/2026
"FOUND L1BROKEN IN THE WIRE NUT, RESPLICED WIRE AND REINSTALLED AND UNIT CHECKED OKAY"
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Medford, Oregon 97501
Kyle
Job Details:
06/04/2026
Found unit continuously draining when unit has power. No activation on main control. Replaced main control and tested. Unit is operating as intended.
We serviced a
BOSCH DISHWASHER
Model SHP65CM5N/25
Near Milwaukie, Oregon 97267
Austin
Job Details:
06/04/2026
6/4/26 BA: CC unit will not run and is flashing lights. Tech looked over the unit and found it was having issues draining. Tech found the drain pump cover to be dislodged from its mounting position. Tech placed the cover back into position and tested the machine. Unit is now operating without issues. Service complete
We serviced a
KITCHENAID DISHWASHER
Model KUDE70FVPA0
Near Ashland, Oregon 97520
Kyle
Job Details:
06/04/2026
"Found unit filling with water. Unit wash pump faulty, will not pump water around inside tub, causing dishes to not get wet or clean. Found excessive debris and glass in filter and under filter in sump assembly, possible peice of debris stuck in wash pump. Advise replace sump and motor assembly, part is factory back order with no eta. Customer is going to purchase new unit."
We serviced a
WHIRLPOOL WASHER
Model WFW5720RR0
Near Colorado Springs, Colorado 80921
Torrey
Job Details:
06/04/2026
"Cx showed a video of a load out of balance and knocking around. There is no tub variance or separation. Ran a factory calibration. Next a cycle of wet towels was run in order to see if calibration was successful. There were no error codes present. Test cycle showed smooth, non thumping or vibrating cycle. Owner verified this is much better."
We serviced a
KITCHENAID DISHWASHER
Model KDTM405PPS1
Near Cloverdale, Oregon 97112
Nathan
Job Details:
06/04/2026
Wire came off of divertor motor See notes Tested Advised of survey
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Roseburg, Oregon 97471
Chris
Job Details:
06/04/2026
"Replaced the gear case, and wash plate. Recalibrated and tested."
We serviced a
WHIRLPOOL DRYER
Model WED4307SW0
Near Pueblo West, Colorado 81007
Domingo
Job Details:
06/03/2026
Replaced motor idler and rollers test it noise was less it would vibrate at the bottom I tight the screws and it helped at this Time Machine is working fine
We serviced a
SAMSUNG REFRIGERATOR
Model RS22T5201SR/AA
Near Lafayette, Oregon 97127
Jesse
Job Details:
06/03/2026
"(JG) June 3 / 12:11 pm called and provided eta 45 mins Replaced parts, verified no leaks , evacuated system , charged to spec."
We serviced a
SAMSUNG WASHER
Model WF50BG8300AVUS
Near Willamina, Oregon 97396
Austin
Job Details:
06/03/2026
6/3/26 BA: CC unit leaking. Tech looked over unit and found the bellows of the machine torn. Tech replaced the bellows assembly and tested the unit for leaks. No further issues found. Service complete.
We serviced a
MAYTAG DRYER
Model MED6230HW2
Near Fruita, Colorado 81521
James R
Job Details:
06/03/2026
"Signed disclaimer. Tore apart and replaced thermal,heat element and installed a repair kit. Re- assembled and run is heatinmg operating as designed. Please fill out tech satisfaction survey. Thank You."
We serviced a
LG REFRIGERATOR
Model LRMDS3006S/01
Near Bend, Oregon 97702
Levi
Job Details:
06/03/2026
"Replaced craft ice maker, could not test because unit is not currently hooked up."
We serviced a
LG WASHER
Model WM8100HVA
Near Bend, Oregon 97701
Levi
Job Details:
06/03/2026
Replace drain pump tested and all checks okay. I'm all done sir
We serviced a
LG REFRIGERATOR
Model LRRXC2606S.ASTCNA0
Near Bend, Oregon 97701
Levi
Job Details:
06/03/2026
Replaced water valves tested and all checks okay.
We serviced a
ILVE RANGE
Model UPDW90FDMP/I
Near Colorado Springs, Colorado 80903
Ralph
Job Details:
06/03/2026
"DONT BELIEVE INSPECTOR NEW THIS MACHINE, WHEN LIGHTING THE BURNERS, THE BURNER KNOB NEEDS TOBE PUSHED BACK AND THEN TURN IT ON TILL UNIT SPARKS AND WAIT A FEW SECONDS TO GIVE THE THERMAL COUPLE TIME TO SET AND THE BURNERS WILL STAY ON, SECONDLY ON THE LARGE OVEN ONCE YOU TURN IT ON THEN YOU NEED TO SET THE COOK TIME ON THE TIMER TO GET THE OVEN TO TURN ON, OVER ALL CHECK THIS UNIT IS WORKING CORRECTLY...AUTHO NO. M9Y49Y"
We serviced a
WOLF RANGE
Model DF36650/S/P
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
06/03/2026
"WHEN OFFICE RESCHEDULED THEY DID NOT CHANGE THE ISSUE, INSTALLED PIECE OF TRIM I MISPLACED AND FORGOT ABOUT, CUST HAPPY WITH RESULT"
We serviced a
JENN-AIR WALL OVEN
Model JMW3430LM02
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
06/03/2026
REPLACED PART AND CUST TO MONITOR
We serviced a
AMANA MICROWAVE
Model AMV2307PFW08
Near Bend, Oregon 97702
Levi
Job Details:
06/03/2026
"Replace filter board fuses and switches, test it all checks okay"
We serviced a
MAYTAG WASHER FRONT LO
Model MTW7200RF1
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
06/03/2026
"Customer states new UI console is intermittently powering off, found connector for filter not fully engaged, corrected and tested unit, working well and tested through diagnostics. Advised customer of situation and survey. Case number 23735309"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Medford, Oregon 97504
Kyle
Job Details:
06/03/2026
"Found main control has fault, when unit is plugged in drain pump continuously runs, control will not activate with any buttons. Replaced main control and tested. Unit is operating as intended."
We serviced a
WHIRLPOOL WASHER
Model WTW7000DW3
Near Eagle Point, Oregon 97524
Kyle
Job Details:
06/03/2026
Customer states that unit will drain but not spin. Customer had none selected in the spin cycle settings. Moved to high and ran a full rinse and spin cycle. Unit is operating as intended.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Shady Cove, Oregon 97539
Kyle
Job Details:
06/03/2026
"Found noise during agitation, found balance ring had come separated from tub. Reinstalled balance ring and tested. Unit is operating as intended."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853ADE
Near Gold Hill, Oregon 97525
Kyle
Job Details:
06/03/2026
"Replaced evap fan and fan blade. Powered unit up, no more draw from evap fan. Set temps to factory recommended. Advised customer that will be about 24-48 hours to get down to temp, and 72-96 hours to have full bucket of ice."
We serviced a
KITCHENAID DISHWASHER
Model KDPS324SPS0
Near Fruita, Colorado 81521
Clint
Job Details:
06/03/2026
"Customer signed disclaimer and recieved parts ordered ,installed new pump and fuse and washer works perfectly now.PLEASE TAKE TECH SURVEY THANKS.CLINT"
We serviced a
GE REFRIGERATOR
Model HPS10LGVBRBB
Near Clifton, Colorado 81520
Sean
Job Details:
06/03/2026
Verified the information customer signed disclaimer.Checked the unit and found that the evaporator had ice build up on it . I pulled the unit out and unplugged it .Instructed the customer to let it melt and plugged it back in.Ice is coming from the ice trays.Advised the customer to make ice on the bottom shelf.Checked the door gaskets all checked good.
We serviced a
LG DRYER
Model DLEX7700BE
Near Colorado Springs, Colorado 80925
Mathew
Job Details:
06/03/2026
Found door coming apart at bottom. Inside of door screw holes are stripped. Recommend replacing entire door assy. $149.95 CC Auth# VA3L4KSvf $149.95Cx not repairing due to cost. MPs$17.50 ADC74908002 door $649.21Tax $52.23
We serviced a
FRIGIDAIRE RANGE
Model FCFE3083ASE
Near Woodland Park, Colorado 80863
David
Job Details:
06/03/2026
"Installed ordered parts, tested and is operating good."
We serviced a
GE REFRIGERATOR/TOP
Model GNE25JGKWFWW
Near Lincoln City, Oregon 97367
Nathan
Job Details:
06/03/2026
Lower hinge bushing cracked causing door to drop down Flapper on LH door had warn down due to the low door Flapper was not functioning properly causing frost build up Tested Advised of survey
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFN2853AFH
Near Florissant, Colorado 80816
Charles
Job Details:
06/03/2026
Replaced mullion flap
We serviced a
PERLICK ICE MACHINE
Model HP15CU-L
Near Divide, Colorado 80814
Charles
Job Details:
06/03/2026
Replaced internal drain pump and all included hoses.
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Colorado Springs, Colorado 80909
Mathew
Job Details:
06/03/2026
Replace inner door. Test op. All okay.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFC3036RZ01
Near Albuquerque, New Mexico 87111
Tye
Job Details:
06/03/2026
Arrived and cx complaint of making noise. Between cx and i we have differing opinion on noise level. I think it is functioning at a normal noise level. He isn't happy with the noise level. At this point cx is contacting Costco for possible exchange.
We serviced a
MONOGRAM FREEZER
Model ZIF181NBRII
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
06/03/2026
"cleared some ice that was blocking the fill cupon the ice mkr, unit hecked okay...autho no. k9pxy4"
We serviced a
MAYTAG REFRIGERATOR
Model MRFF4236RZ02
Near Albuquerque, New Mexico 87123
Jason
Job Details:
06/03/2026
Installed compressor. pressures and heat exchange check ok. spoke to cx about review
We serviced a
LG REFRIGERATOR
Model LFCS22520S/05
Near Powell Butte, Oregon 97753
Richard
Job Details:
06/03/2026
Installed new compressor and filter dryer cycle tested unit all tested good at this time unit working as designed. Customer has refrigerator and washer on scene. 15 amp circuit could possibly cause issues with the refrigerator when using the washer job complete
We serviced a
MAYTAG DRYER
Model MGDC500VW0
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
06/03/2026
Arrived and cx complaint of not heating right. Ran dryer to temp and noticed after first ignition dryer started cooling down. Removed igniter and ignition coils..tested dryer. Unit is functioning now as designed. Informed cx of review
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Fountain, Colorado 80817
Carlos
Job Details:
06/03/2026
Installed control board ran tests and calibration.
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
06/03/2026
Installed control board ran cycle up to 350 ran ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6600QLAA
Near Selma, Oregon 97538
Chris
Job Details:
06/03/2026
Replaced the icemaker assembly and tested.
We serviced a
DACOR DISHWASHER
Model DDW24G9000APDA
Near Pueblo, Colorado 81004
Domingo
Job Details:
06/03/2026
Replaced the bottom base have to take machine whole apart to do that unwired the control took board out out new base in install all wires level the machine raise legs ran hass and it passed
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Prineville, Oregon 97754
Richard
Job Details:
06/03/2026
Removed old struts replaced cycle tested all tested fine at this time
We serviced a
MAYTAG WASHER
Model MVWB835DW4
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
06/03/2026
Arrived and removed failed valve. Installed new valve. Washer would not initially cone on. Put unit into diagnostics. Ran diagnostics. F-8 e- 1 code. Long fill. Cleared code. Tested washer on quick cycle. Washer is functioning now as designed. Informed cx of review.
We serviced a
WHIRLPOOL DRYER
Model WED6150PB0
Near Colorado Springs, Colorado 80918
Jason
Job Details:
06/03/2026
"Moisture sensor bars were disconnected, receded the connection and tested, No other issues found unit repaired, spoke to customer about the survey"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC136RPS00
Near Sunriver, Oregon 97707
Levi
Job Details:
06/03/2026
Replace the user interface and high voltage control board along with the ice maker. Test it and all functions test good and performed a quick test on the ice maker and it cycled. It will not call for water until it is cold enough to do so. Asking property Management company to check on ice maker see if it's doing anything in the next 24 to 48 hours and the let us know if it is not functioning properly.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Grand Junction, Colorado 81501
Clint
Job Details:
06/03/2026
Customer signed disclaimer and recieved parts ordered.insatlled new control and reset it.Ran unit and it washed and spun out. No leaks detected. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
BROAN RANGE HOOD
Model 273603
Near Manitou Springs, Colorado 80829
Charles
Job Details:
06/03/2026
"Downdraft retractable vent frame bent by previous repair company, teflon slide bushing missing, causing too much play and catching glass cooktop. Frame is not an available part. called AHS to document. Service fee 169.95, Crystal Park fee $85.00, Total $254.95"
We serviced a
WHIRLPOOL WASHER
Model NTW4516FW4
Near Trinidad, Colorado 81082
James
Job Details:
06/03/2026
"Installed ordered part per service flash. Recalibrated and tested ops, all ckok"
We serviced a
MAYTAG WASHER
Model MHWE300VF00
Near Albuquerque, New Mexico 87123
Jason
Job Details:
06/03/2026
Checked unit found f32 error. found plug not seated. seated plug. ran a quick cycle. unit operation checks ok. spoke to cx about review Auth code: P9HJHM$162.70
We serviced a
MAYTAG WASHER
Model MTW7200RF1
Near Albuquerque, New Mexico 87110
Jason
Job Details:
06/03/2026
Checked unit found hose had come apart. installed hose. ran quick cycle unit operation checks ok. spoke to cx about review
We serviced a
SAMSUNG REFRIGERATOR
Model RSG257AARS/XAA
Near Colorado Springs, Colorado 80905
Mathew
Job Details:
06/03/2026
Needs icemaker replacement $149.00 CK Auth# W9F3R3Svf $149.95MPs $17.50DA97-11092B $293.42 Tax $24.06$484.93 due to order parts Labor $199.95$684.88
We serviced a
GE DRYER
Model GFD14ESSN2WW
Near Vail, Colorado 81657
Erik
Job Details:
06/03/2026
VENT ISSUEBOOSTER FAN RUNNING IN REVERSE?CALL GE TAG: CASE#23305760JOB COMPLETE
We serviced a
WHIRLPOOL DISHWASHER
Model WDT720PADM2
Near Colorado Springs, Colorado 80919
Mathew
Job Details:
06/03/2026
Replace parts. Test op all okay. Left leak strips in place.
We serviced a
WHIRLPOOL DISHWASHER
Model WDPS7024RZ0
Near Grants Pass, Oregon 97526
Chris
Job Details:
06/03/2026
Unable to find a leak at this time. The customer is going to monitor it.
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Colorado Springs, Colorado 80924
Torrey
Job Details:
06/03/2026
The drive belt is off the idler pulley. Pulley does not turn freely and probably kicked the belt off. Replaced the idler pulley and belt. Tested good. Advised tenant of the situation.
We serviced a
SAMSUNG DRYER
Model DVE45A6400V
Near Colorado Springs, Colorado 80924
Mathew
Job Details:
06/03/2026
"Replace parts. Test op, unit working as expected. All okay."
We serviced a
MIELE COFFEE MACHINE
Model CVA7845
Near Vail, Colorado 81657
Erik
Job Details:
06/03/2026
REF# 1011524717CONNECT TO MDU F283 COMM ERRORFT21 8PIN (3/4 13.5 VDC)POWER BOARD 11635933 (GOOD)DOOR BOARD 12145110 (GOOD)APPLY VARIANTS PROGRAM AND TEST: PASS$250.95 paid autho# L3YWR3JOB COMPLETE
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFHB2750TS0
Near Colorado Springs, Colorado 80920
Earl
Job Details:
06/03/2026
"Hi, install the ice baker after defrosting all the frost inside of it.And tested , the unit is operating properly at this time"
We serviced a
MAYTAG DRYER
Model MED7230HW1
Near Colorado Springs, Colorado 80918
Torrey
Job Details:
06/03/2026
Tech found not heat on dryer. Good airflow to the outside. Replaced defective element and cutoff fuse kit. Cleaned dryer. Tested good. Advised customer of situation and survey.
We serviced a
WHIRLPOOL DISHWASHER
Model WDF332PAMS0
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
06/03/2026
Installed control board ran tests all ok
We serviced a
PROFILE REFRIGERATOR
Model PFE28KELHDS
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
06/03/2026
Replaced led light and all lights now working properly. RK
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814WWE
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
06/03/2026
"Found open/failed heating element assembly. Defrosted unit and replaced heater assembly. Unit is now working properly, allow 24 hrs to cool. RK"
We serviced a
GE DISHWASHER
Model PDT755SYV6FS
Near Hotchkiss, Colorado 81419
Sean
Job Details:
06/03/2026
Verified the unit information customer signed disclaimer.Opened the unit and installed the new 3rd rack manifold docking port.Checked the alignment and closed the top rack.Tested good.
We serviced a
WHIRLPOOL FREEZER
Model WRS321SDHW11
Near Grand Junction, Colorado 81506
James R
Job Details:
06/03/2026
Signed disclaimer. Found a chunk of ice caught in flapper and ice chute. Explained to customer that they need to push the dispenser flap all the way back so it opens all the way. It then can close slowly allowing ice to drop thru properly. Also explained to customer that crushed ice pieces of ice can collect and not drop thru and cause a dripping of wtr into the catch tray. Please fill out tech satisfaction survey. Thank You.