We serviced a
MAYTAG REFRIGERATOR
Model MFI2569YEM0
Near Pueblo West, CO 81007
James
Job Details:
11/13/2023
"found cntl resetting after power surge unit is now working may need main cntl WPW10312695 267.50, sc 149.95, labor 149.95, mps 14.50. Total: 603.84/453.89, cust declined collected 149.95"
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Albuquerque, NM 87105
Larry
Job Details:
11/13/2023
CX complaint - Washer leaking - Inspected unit and found the valve failed - Replaced with TS and tested good - Unit is good to go; used 1 W11513255 (Valve) from stock
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW2
Near Cedar Crest, NM 87008
Jason
Job Details:
11/13/2023
Installed control and calibrated unit. unit opperation checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Edwards, CO 81632
Antonio
Job Details:
11/13/2023
Installed new acu and pump motor unitvtested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ00
Near Vail, CO 81657
Antonio
Job Details:
11/13/2023
Found bad compressor unit is up for review sr#7737776416
We serviced a
TRUE REFRIGERATOR
Model TBB-3G
Near Colorado Springs, CO 80906
Ralph
Job Details:
11/13/2023
"unit has a locked comp, will need repalcement, cust thinking of replacing the unit...cust paid totla bill autho no. VK3M3U"
We serviced a
WHIRLPOOL M/W OTR
Model WMH53521HZ06
Near Colorado Springs, CO 80924
Aaron
Job Details:
11/10/2023
"Control relay burnt , light bulb shorted as well, replaced components and tested, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MHW6630HW0
Near Fruita, CO 81521
James R
Job Details:
11/10/2023
F9E1 error code long drain. Cleared error code. Removed front of washer. Removed water and then pump inspected looked ok reassembled unit and put thru diagnostics test clear code. Did test 12. At end when got ready to drain pump hummed. It is faulty. W11458345 Customer will replace washer. Customer paid $149.95 auth code. 399A3T
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB543CMJZ00
Near Colorado Springs, CO 80920
Aaron
Job Details:
11/10/2023
"Removed and replaced door assembly, no dents or scratches, verified by customer. Working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM03
Near Colorado Springs, CO 80909
Carlos
Job Details:
11/10/2023
Installed gasket all ok
We serviced a
WHIRLPOOL DRYER
Model WED72HEDW1
Near Colorado Springs, CO 80918
Aaron
Job Details:
11/10/2023
"Idler and rollers are worn and squeaking, removed and replaced, lubricated, and tested unit. Working and heating well now. Advised customer of 5 star survey."
We serviced a
GE WASHER
Model GFW850SPN5RS
Near Leadville, CO 80461
Erik
Job Details:
11/10/2023
shipping bolt still installed/ remove and test: wobblesflooring weak in rear left corner of laundry space - CX prop mgmt knows they need to reinforce the floor to correctconnect to smartHQ service: spin test after securing unit: PASSJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, NM 87111
Jason
Job Details:
11/10/2023
installed basket unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW08
Near Colorado Springs, CO 80915
Carlos
Job Details:
11/10/2023
Ran test op. Found ice build up on evaporator fan blade. Replaced fan motor and fan blade and cleared up ice. Ran test op all ok
We serviced a
WHIRLPOOL RANGE
Model SF362LXST0
Near Albuquerque, NM 87104
Larry
Job Details:
11/10/2023
CX complaint - Oven not heating - Inspected unit nad found the control is not sending a signal to the ignition system - Parts are NLA - Collected SC
We serviced a
WHIRLPOOL M/W OTR
Model KHMC1857WSS0
Near Albuquerque, NM 87108
Jason
Job Details:
11/10/2023
installed switches and fuse unit checks okAuth code:33P9LN$206.10
We serviced a
WHIRLPOOL DRYER
Model WED5010LW1
Near Albuquerque, NM 87120
Larry
Job Details:
11/10/2023
CX complaint - Not dryling - Inspected unit and found the vent run clogged - CX had already cleaned a huge amount of lint from the run but it is still failing for electric dryers - Advised cx to have vents cleaned
We serviced a
MAYTAG DRYER
Model MED6230HW0
Near Albuquerque, NM 87114
Larry
Job Details:
11/10/2023
Installed parts listed and tested goo - Unit is good to go
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Albuquerque, NM 87105
Jason
Job Details:
11/10/2023
installed timer and knob unit checks ok
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA
Near Pueblo, CO 81005
Brandon
Job Details:
11/10/2023
"Ran hass got error 5c, replaced drain pump, tested op all checks ok hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF22KREDBSG/AA
Near Pueblo West, CO 81007
Brandon
Job Details:
11/10/2023
Replaced auger assy and tested op all ok hass passed
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Penrose, CO 81240
Brandon
Job Details:
11/10/2023
"Replaced evap cover, pcb and damper, tested op all checks ok hass passed"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFHT2021QW0
Near Pueblo, CO 81001
David
Job Details:
11/10/2023
Checked refrigerator Cleaned defrost drain
We serviced a
SAMSUNG REFRIGERATOR
Model RF265BEAESR/AA
Near Colorado Springs, CO 80923
Glenn
Job Details:
11/10/2023
"Defrost Ice buildup, Install Ice room kit, Auger Motor Assy, Adjust fill tube. Corner already sealed from prior repair. Cycle Test IM, Fill > OK, All OPS Test OK."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Colorado Springs, CO 80919
Glenn
Job Details:
11/10/2023
Install New Damper in FF. All OPS Test:OK
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Colorado Springs, CO 80919
Glenn
Job Details:
11/10/2023
"Error Code 8-4 : Overfill/Float Switch Open , Found water in drip tray. Empty tray, Reseat connections to PCB, Ran Diagnostics 3X, No Leaks. Did see foam inside unit. added half cap of wesson oil into tub, to rid foam. All OPS Test:OK, No Leaks, Adjusted front legs a little bit to provide better pitch. Suggest stop using PODS w/ rinse aid, and use liquid detergent, until all dispenser rinse aid is empty. Customer will continue to monitor."
We serviced a
KITCHENAID DISHWASHER
Model KDFE104DSS3
Near Colorado Springs, CO 80921
Glenn
Job Details:
11/10/2023
"sounded like something was hitting in wash cycle. Unit has always continued to work, but customer turned off breaker for safety. All OPS Test:OK, No weird sounds or noises. Ran Diag Cycle 2X. Possibly loading issue caused noise when it occurred for cutomer. Did find a small shard of glass in bottom of tub. Had customer clean screen & filter. Customer will continue to monitor and call back if needed. Paid SC fee of $129.95, Autho#W33C3T"
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Colorado Springs, CO 80921
Glenn
Job Details:
11/10/2023
"Marcone was inncorrect, part did not come with screws needed. Had to go to hardware store to obtain a replacement screw & washer. Installed New Rack holders and Screw w/ washer obtained from hardware store. All OPS Test:OK"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Monument, CO 80132
Glenn
Job Details:
11/10/2023
"Compressor, Evap Fan & Condensor fan motors running. Unable to determine any noise that is out of the ordinary.Techline: Comprerssor drawing .68amp > OK , Adjusted coolant lines around compressor & used cardboard to tighten cardboard panel under unit, in case vibration noises from it. Suggest customer attempt to record sound next time it occurs. Also, did not find any styrofoam in Dispenser chute, possible foam left over from shipping of unit? No Foam incorporated in design of unit, as far as I can tell. If problem returns, suggest send a different technician for 2nd opinion.SR#7737766774"
We serviced a
WHIRLPOOL M/W OTR
Model WMH78019HZ05
Near Los Lunas, NM 87031
Larry
Job Details:
11/10/2023
CX complaint - Humming noise when fan is on - Inspected unit and found packing material in MW cabinet - Removed and tested good - Unit is operating as designed
We serviced a
MAYTAG WASHER
Model MVWC565FW
Near Colorado Springs, CO 80907
Roman
Job Details:
11/10/2023
Cx wondering why theres not that much water. Explained to her that you have to fill the tub with more clothes to have it fill up more and explained which cycles to use for the amount of clothing.
We serviced a
GE REFRIGERATOR/TOP
Model FUF21QRRAWW
Near Colorado Springs, CO 80906
Roman
Job Details:
11/10/2023
Installed new door gasket and door is opening easier.
We serviced a
ASKO DISHWASHER
Model D5656XXLHS
Near Colorado Springs, CO 80906
Roman
Job Details:
11/10/2023
"Pulled the dw out and the float is touching the switch to the leak sensor. Dw leaking from the divider. Recommend replacing the divider, inlet valve and float. Valve #434374. $115.00Divider #700497 $159.00Float #700354 $72.50Tax $28.41Total parts $ 374.91MPs $14.50Labor $449.95Sc $149.95Total cost $989.31 Paid sc $149.95 CC Auth# F9JC33"
We serviced a
BOSCH DISHWASHER
Model SHPM78Z55N/22
Near Colorado Springs, CO 80906
Roman
Job Details:
11/10/2023
Ran dw through the diagnostic mode and its went through all the cycles without error codes. Noticed that the water was taking a long time to drain out. Checked the drain line and it was a mess so removed the drain line and attached it onto the disposal. Tested the dw and it drained out way faster and working great. Checked under neath it for leaks and checked the drain pump drain pump looks fine and had nothing stuck in it. Dw working great.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9070SG/AA
Near Colorado Springs, CO 80908
Mathew
Job Details:
11/10/2023
Replaced icemaker parts. Test op all okay.
We serviced a
GE REFRIGERATOR/TOP
Model PYE22KYNIFS
Near Colorado Springs, CO 80906
Roman
Job Details:
11/10/2023
"Checked the ice bin and dispenser and the fridge is still freezing the lines. Added some styrofoam foam and raised the temps in the fridge. Did not use the new gasket, old one is sealing great after using vasaline on it."
We serviced a
GENERAL ELECTRIC MICROWAVE OVEN
Model RVM5160DH8WW
Near Colorado Springs, CO 80906
Roman
Job Details:
11/10/2023
"Checked the fan and it is not blowing out the front, pulled the microwave down and lipped the cooling fan. Tested the microwave and its blowing air out of the top vents. Microwave working great."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS01
Near Pueblo, CO 81001
Kris
Job Details:
11/10/2023
cx is deciding on repairs fc temp@21.5 rc temp@33.1 unit has both evaps covered in ice will need listed parts. unit may have other issues. will need listed parts before i will know if unit needs additional parts.WPW10675033 control 267.45W11087438 fan 142.12 w11249952 142.12
We serviced a
GE WALL OVEN
Model CTD90FP2NS2S1
Near Colorado Springs, CO 80919
Kris
Job Details:
11/10/2023
installed fans. unit has a vibrating sound from they way the pannels are built. showed cx video of back of unit with all screws installed unit makes loud sounds when touching pannels. vibrating when units cooling fan is on.
We serviced a
SAMSUNG REFRIGERATOR
Model RB215BSSB
Near Colorado Springs, CO 80911
Roman
Job Details:
11/10/2023
"Checked the fresh food and it seems to be cooling okay. Freezer section is at 49 degrees. Checked the compressor and its pulling 16 amps indicating it is failing. And very hot to the touch. Condenser fan motor is not running but getting volts to it and the fan blade is completely broken. Recommend replacing the compressor, fan motor and fan blade .Compressor #N/AFan motor # N/AFan blade #N/AParts are not available for this fridge and none repairable."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ
Near Colorado Springs, CO 80925
Carlos
Job Details:
11/10/2023
"Installed compressor and charged. Low side pressure -1, high side pressure 95."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHB01
Near Pueblo West, CO 81007
David
Job Details:
11/10/2023
Replaced icemaker Icemaker filled with water
We serviced a
WHIRLPOOL WASHER
Model MHW5630HC2
Near Pueblo, CO 81005
David
Job Details:
11/10/2023
Checked washer Cold water valve 1 not flowing good Ck thinking about repairs Service fee of 149.95 good for 30 days
We serviced a
ELECTROLUX DRYER ELECTRIC
Model EIMED60LT3I
Near Colorado Springs, CO 80921
Kris
Job Details:
11/10/2023
cx is deciding on repairsblower 246.70 134690800motor 307.50 5304529782rollers x4 119.38 5304523155idler 79.18 134793511
We serviced a
SAMSUNG ELECTRIC OVEN
Model NQ70M7770DG/AA
Near Peyton, CO 80831
Jerimiah
Job Details:
11/10/2023
"Installed replacement components, unit check ok checked unit 30 times, (Cust watched), there was one failure, where high voltage did not kick on, plus unit did pop once but could not find where that was located. Closing call"
We serviced a
THERMADOR VENT HOODS
Model HII8057U/03
Near Breckenridge, CO 80424
Erik
Job Details:
11/10/2023
NOT THERMADOR PRODUCT**CX to call mountain high appliance for warranty**cancel service unless dispacthed by manufacturer or MHA
We serviced a
DACOR OVEN
Model ERD30S06BK/H
Near Colorado Springs, CO 80920
Jerimiah
Job Details:
11/10/2023
"Control dead and hinges sprung needs replacing, found both parts are NLA, charging service call. $172.44 CC Auth# 43MJ4U92028 controller 62436 hinge x2"
We serviced a
WHIRLPOOL RANGE
Model GR448LXPS0
Near Colorado Springs, CO 80904
Carlos
Job Details:
11/10/2023
"Ran test op. Broil relay on control board opens intermittently. Needs a new board (9757271) part is discontinued, can be sent out for repair. Cx will not repair. Cx paid SC $149.95 CC Auth# F4C449"
We serviced a
GE MICROWAVE
Model JKP90SP3SS
Near Manitou Springs, CO 80829
Ralph
Job Details:
11/10/2023
installed part and unit checked okay
We serviced a
KITCHENAID MICROWAVE
Model KMBP100ESS01
Near Colorado Springs, CO 80919
Carlos
Job Details:
11/10/2023
Ran test op. Microwave was stuck in demo mode. Turn off demo mode runs all ok Cx paid SC $129.95 CC Auth# UY4K34
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9771SG/AA
Near Colorado Springs, CO 80909
Mathew
Job Details:
11/10/2023
"Found installer severed cable on bottom right door. Will need new door. Called tech line. Samsung is not covering repair, deemed physical damage. DA93-00934G part."
We serviced a
SAMSUNG MICROWAVE
Model ME21M706BAS/AA
Near Colorado Springs, CO 80909
Mathew
Job Details:
11/10/2023
"Called tech line about walls of microwave being discolored, ticking noise coming unit while running. Tech-Line states Cx will have to open another ticket about discoloration. Microwave heated up water efficiently."
We serviced a
GE REFRIGERATOR
Model GSS25IYNXHFS
Near Pueblo, CO 81003
David
Job Details:
11/10/2023
"Checked refrigerator A little rattle from the compressor area Repositioned a couple of lines a little, no more rattle. Everything working normal"
We serviced a
GE REFRIGERATOR/TOP
Model GFE28GYNJFS
Near Breckenridge, CO 80424
Erik
Job Details:
11/10/2023
connect to smartHQ service: *see quick pics**NO ERROR CODES ACTIVE**abnormal defrost 1st cycle extended 15 min. (cause unknown) melted ice in bin and melted through port hole (all other plumbing inspected for leaks - none found)Ica maker test confrims ice maker asm working correctly - no leakspaddle dispenser checked with internal panel removed to inspect water tank and valve - no leaksNO ACTION REQUIRED AT THIS TIME
We serviced a
GENERAL ELECTRIC DISHWASHER
Model PDT755SYR5FS
Near Breckenridge, CO 80424
Erik
Job Details:
11/10/2023
installed/tested with clear door: PASS all cycles all zones
We serviced a
WHIRLPOOL WASHER
Model MVW6230HC3
Near Colorado Springs, CO 80908
Aaron
Job Details:
11/10/2023
"Gearcase making noise during cycle, removed and replaced gearcase, pulley, and belt. Working well now. Lifted front legs and verified level. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVWE655DW1
Near Colorado Springs, CO 80908
Aaron
Job Details:
11/10/2023
"Gearcase leaking, gears are stuck in spin, entire tub rotating during agitation, motor and belt are burning, drive block is wearing as well. Discussed with customer, no estimate needed, they are purchasing new. Auth 129.95 hc #4LR4VH"
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Colorado Springs, CO 80922
Aaron
Job Details:
11/09/2023
"Line loose at terminal block, shorted and melted wire and terminal, replaced terminal block and wires, customer unavailable to advise of survey or obtain signature."
We serviced a
WHIRLPOOL DRYER
Model MED3500FW0
Near Colorado Springs, CO 80919
Carlos
Job Details:
11/09/2023
"Installed idler pulley, ran test op all ok. Cx paid"
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Colorado Springs, CO 80951
Roman
Job Details:
11/09/2023
Ran the washer in diagnostic mode and it did not show error codes. Ran it through all the cycles and it worked fine. Washer does shake when in spin mode. Noticed the feet in the front were raised more the the feet in the back. Leveled the washer and tested it.Threw in some towels and ran a rinse and spin mode on them washer seems fine. Recommend to cx trying different cycles with the amount of clothes and towels that are in it.
We serviced a
GENERAL ELECTRIC WASHER
Model PFW950SPT1DS
Near Colorado Springs, CO 80918
David
Job Details:
11/09/2023
Replaced motor and drive belt Ran cycle and is running nicely
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Monument, CO 80132
Glenn
Job Details:
11/09/2023
"Power was cycled on unit, all ops test:OK."
We serviced a
SAMSUNG REFRIGERATOR
Model RF31CG7400SRAA
Near Monument, CO 80132
Glenn
Job Details:
11/09/2023
"Install New Center Drawer Panel. All OPS Test:OK , Customer Satisfied with end results."
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Colorado Springs, CO 80920
Glenn
Job Details:
11/09/2023
"Install New Gearcase, Splutch Kit, Shifter, Cap & Belt. All OPS Test:OK, No Leaks."
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA
Near Colorado Springs, CO 80921
Brandon
Job Details:
11/09/2023
"Found vane deflector not connected, connected the deflector and tested op all ok hass passed"
We serviced a
SAMSUNG DRYER
Model DVE45A6400W/A3
Near Monument, CO 80132
Brandon
Job Details:
11/09/2023
"Thermostat 3 is bad again, unit overheating, all other sensors test ok, recommend getting vent cleaning done"
We serviced a
SAMSUNG DISHWASHER - BUI
Model DW80M2020U
Near Colorado Springs, CO 80911
Brandon
Job Details:
11/09/2023
"Found signs of leaking at drain pump, removed drain pump cleaned seal reinstalled drain pump tested op all ok checked for leaks all ok"
We serviced a
SAMSUNG REFRIGERATOR
Model RS23CB760012
Near Colorado Springs, CO 80911
Brandon
Job Details:
11/09/2023
"Complaint is freezer is too cold, unit has ice maker which is designed to drop temp in freezer to -17 when ice maker is turned on, called tech support to confirm, checked all sensors all test ok"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA 19
Near Fountain, CO 80817
Brandon
Job Details:
11/09/2023
Replaced parts and tested op all ok hass passed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Colorado Springs, CO 80911
Carlos
Job Details:
11/09/2023
Installed bin. Put food products to add weight all ok
We serviced a
WHIRLPOOL MICROWAVE OVEN
Model KMBP100ESS20
Near Colorado Springs, CO 80908
Jerimiah
Job Details:
11/09/2023
Installed replacement inverter board. Unit check ok.
We serviced a
SAMSUNG DRYER - ELECTRIC
Model DVE50R5200
Near Colorado Springs, CO 80925
Brandon
Job Details:
11/09/2023
"Model and serial didn't match, told cx they have to update it with aig warranty"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Colorado Springs, CO 80911
Carlos
Job Details:
11/09/2023
Installed sump assembly and control board runs all ok
We serviced a
MAYTAG WASHER
Model MVWC465HW3
Near Colorado Springs, CO 80925
Carlos
Job Details:
11/09/2023
"Cx explained that washer leaks on front right corner and back left corner. Inspected drain houses, outer tub, motor drive, pressure hose and water hoses all dry, could not determine exact location of leak although there is evidence of water on the floor. Replaced tub ring and water valve Cx will observe."
We serviced a
SAMSUNG GAS RANGE
Model NX60A6311SS/AA
Near Colorado Springs, CO 80925
Jerimiah
Job Details:
11/09/2023
Installed replacement controller w/ display. Unit check ok.
We serviced a
SAMSUNG WASHER
Model WF45M5500AW/A5
Near Colorado Springs, CO 80923
Mathew
Job Details:
11/09/2023
Needs Washer diaphragm DC97-19755a. Quote good for 30 days. Cx not moving forward at the moment. Paid svf 129.95 $129.95 CC Auth# V39K43DC97-19755a 256.78 plus tax 21.06. Parts total 277.84Svf 129.95MPs 14.50Due today $422.29 ($292.34 remaining after svf)Due on install Labor $179.95
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Colorado Springs, CO 80951
Carlos
Job Details:
11/09/2023
"Ran test op. Found broken wire, repaired wire runs ok."
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950UG/AA
Near Colorado Springs, CO 80918
Glenn
Job Details:
11/09/2023
"Installed New Water valve. Informed customer that shutoff valve under sink not turning off all the way, suggest have plumber replace shutoff valve. Test Unit, No Leaks. All OPS Test:OK, Installed Leak Detector for safety."
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Colorado Springs, CO 80918
Glenn
Job Details:
11/09/2023
"Install New Gearcase, Basket, Hub Kit, Splutch kit, Actuator, Belt & Suspension. All OPS Test:OK, No Leaks."
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6200QLAA
Near Colorado Springs, CO 80924
Mathew
Job Details:
11/09/2023
Replaced left door. Test op all okay.
We serviced a
SAMSUNG WASHER
Model WA45T3400AP/A4
Near Colorado Springs, CO 80908
Mathew
Job Details:
11/09/2023
"Pillow Case stuck inside of drive belt. Removed and test op, all okay. Collected svf $129.95$129.95 CC Auth# JR4M93"
We serviced a
FRIGIDAIRE MICROWAVE OVEN
Model GMOS1964AFA
Near Cañon City, CO 81212
James
Job Details:
11/09/2023
"installed ordered parts, adjusted hinge and tested. all ops test good. good temp rise observed."
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Carbondale, CO 81623
James R
Job Details:
11/09/2023
Is in building 900 unit 316 Checked temp is cycling to quickly. Replaced cutoff. 280148 Checked temp timed dry lo 130 hi 156 good. Vent removed. Checked operation of unit in auto cycle with towels in it. Sensing light came on and then wet. So unit is sensing the dampness of the items. Make sure Eco boost is off. Items must touch sensing bars in order to dry properly. Also dry like cloths. A mixed load of thinner and heaver items will not dry the same. If heavier items dont touch the bar it will shut down before items are dry. Checked vent restriction it is hi .60 max should be .58 Will affect the drying. Customer dsigned waiver. Please fill out whirlpool tech satisfaction survey. Thank You. ; used 1 280148 (CUTOFF-TML) from stock
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SR/AA
Near Colorado Springs, CO 80908
Mathew
Job Details:
11/09/2023
"Found reed switch unplugged. Plugged switch in and test op, unit working as expected."
We serviced a
SAMSUNG WASHER
Model WF219ANW/XAA 01
Near Colorado Springs, CO 80921
Mathew
Job Details:
11/09/2023
Found bad tub seal. Unit needs new tub assy or rear tub assy. Could not find part available. Svf 129.95. Cx not repairing.
We serviced a
SPEEDQUEEN DRYER - ELECTRIC
Model ADE4BRGS175TW01
Near Colorado Springs, CO 80921
Mathew
Job Details:
11/09/2023
Replaced outlet cover. Test op all okay.
We serviced a
WHIRLPOOL RESIDENTIAL REFR
Model WRF767SDHZ03
Near Peyton, CO 80831
Kris
Job Details:
11/09/2023
installed compressor and all parts sent charged with 56g of r600 ran tets op all ok unit is working to spec at this time. cx will monitor unit for 24 hours.
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Carbondale, CO 81623
James R
Job Details:
11/09/2023
Checked exaust temp. Cycling too fast. Replaced cutoff. Checked temp lo 132 hi 155 good. Put in a load of sheets and run on auto delicates cycle. Sensing light has come on and now wet. Temp is coming up as should as cloths dry. Need to be sure to dry like cloths. Sheets are thin and will dry quicker than thicker cottons. On auto cycle if the thicker items dont touch the sensing bar the unit will shut off before cloths are dry. Checked the vent restriction it is borderline high .60 which will affect the drying. .58 is max. Also too large of loads if they touch the front vent for too long will affect drying as well. Need to be able to tumble and have a clear screen at times. customer signed waiver. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Peyton, CO 80831
Aaron
Job Details:
11/09/2023
"Crack in Inner corner of unit, removed and replaced lid assembly, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
DACOR DOWNDRAFT VENT
Model RV36W
Near Elbert, CO 80106
Kris
Job Details:
11/09/2023
319.95 for labor msp14.50 cx ordering motor will need 2 hours clean contacts under ui main board de81-07744a 317.78motor de81-06588a 346.99
We serviced a
WHIRLPOOL DRYER
Model WED4616FW0
Near Albuquerque, NM 87108
Jason
Job Details:
11/09/2023
installed parts unit checks ok
We serviced a
KITCHENAID VENT HOODS
Model UXB1170KYS0
Near Granby, CO 80446
Antonio
Job Details:
11/09/2023
Found plastic grill rubbing due to wires pressing against it moved wires unit tested good
We serviced a
WHIRLPOOL ICEMAKER
Model WUI95X15HZ01
Near Albuquerque, NM 87111
Jason
Job Details:
11/09/2023
cx is experiancing an issue where unit shuts all lights off then comes back on. i suspect control is havung an issue. unit is making ice at this time. cx may call wp for a parts concession
We serviced a
WHIRLPOOL RANGE
Model WFE505W0JZ0
Near Cañon City, CO 81212
James
Job Details:
11/09/2023
installed ordered parts. tested ops. all ckok temps cycling at 375 and 325
We serviced a
WHIRLPOOL RANGE
Model WEG750H0HZ2
Near Fraser, CO 80442
Antonio
Job Details:
11/09/2023
Installed new ui panel unit tested good
We serviced a
SAMSUNG RANGE GAS
Model NX60A6311SS/AA
Near Colorado Springs, CO 80925
Jerimiah
Job Details:
11/09/2023
"Buttons randomly not working, cycled power on unit and buttons are working again. Previously replaced keypad and controller are under 90 day warranty til 12-12-23. Techline says display could possibly cause communication disruption between components. Cust will look for new appliance. Charging service call. Labor will be $189.95 upon return service if decided. $136.45 CC Auth# 44A3VKDG94-04041C Control boardDG96-00850D KeypadNotes:DG92-01232C Display"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Edgewood, NM 87015
Jason
Job Details:
11/09/2023
installed burner unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Albuquerque, NM 87121
Larry
Job Details:
11/09/2023
CX complaint - DW wont run - Inspected unit and found the sump and control failed - Replaced both and tested good - Unit is good to go
We serviced a
GE WASHER
Model PTW700BST0WS
Near Colorado Springs, CO 80906
David
Job Details:
11/09/2023
"Checked washer Ck stated that machine is walking forward Ran diagnostics all ran good Error codes showing43 inverter faults 92 inverter heartbeat failure 26 out of balance, redistribution 31 out of balance, fallback in final spinCalled tech line His suggestion is to use deep fill and deep rinse so the clothes don't knot up as bad Case number 11469742"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Elbert, CO 80106
Aaron
Job Details:
11/09/2023
"Water inlet flume clip not fully secure, drain hose in standpipe, corrected both issues and tested unit, working well. Advised customer of usage with new 'he' unit's and of survey."