We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Colorado Springs, CO 80923
Brandon
Job Details:
03/20/2024
Replaced parts and tested op all checks ok hass oqc passed
We serviced a
SAMSUNG WASHER
Model WF45B6300AP/US
Near Colorado Springs, CO 80925
Mathew
Job Details:
03/20/2024
"Replaced spin basket, rear and front tub. Test op, all okay."
We serviced a
MAYTAG DRYER
Model MEDX655DW1
Near Albuquerque, NM 87114
Joe
Job Details:
03/20/2024
cx complaint - n heat - inspected unit - found cut off fuse bad - replaced fuse - unit good to go; used 1 279816 (cut off) from stock
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Rio Rancho, NM 87124
Joe
Job Details:
03/20/2024
cx complaint - agitator cap keeps coming off - replaced cap ordered last visit - tested unit - unit good to go - advised about survey
We serviced a
WHIRLPOOL DRYER
Model WED5605MC0
Near Edwards, CO 81632
Antonio
Job Details:
03/20/2024
Installed new housing and acu unit tested good
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS2
Near Edwards, CO 81632
Antonio
Job Details:
03/20/2024
Installed hinges unt tested good
We serviced a
KITCHENAID RANGE
Model KFGC506JMH05
Near Eagle, CO 81631
Antonio
Job Details:
03/20/2024
Adjusted valves to each burnner unit tested good
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW0
Near Los Lunas, NM 87031
Larry
Job Details:
03/20/2024
Installed washplate and agitator and tested good - Unit is good to go - Servey mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Los Lunas, NM 87031
Larry
Job Details:
03/20/2024
CX complaint - right before the final spin cycle- whirling noise loud noise - Inspected unit and found the retaining bolt that holds the rotor on cameout - Applied loc-tite and secured bolt - advised cx to wait 24 hours before using unit - Unit should be good to go
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS09
Near Los Lunas, NM 87031
Larry
Job Details:
03/20/2024
"Installed control, housing and lamp and tested good - Unit is good to go - Servey mantioned"
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Socorro, NM 87801
Larry
Job Details:
03/20/2024
"CX complait - Dryer not heating enough - Inspected unit and found High temp heating between 142 and 215 degrees, med temp between 120 and 193 degrees and low temp between 104 and 180 degrees - Unit is operating as designed - Servey mentioned"
We serviced a
SAMSUNG DRYER
Model DV331AER/XAA
Near Pueblo, CO 81008
James
Job Details:
03/20/2024
found disconnected wire interfering with dryer drum causing unit to not start. secured wire and tested all ops test good. pics in qp
We serviced a
SAMSUNG DRYER
Model DV42H5000EW/A3
Near Colorado Springs, CO 80927
Kris
Job Details:
03/20/2024
ran test op unit has bad element dc97-14486a 282.50
We serviced a
GE REFRIGERATOR
Model GSS25IMNZHES
Near Pueblo West, CO 81007
James
Job Details:
03/20/2024
found door seal sticking out from door causing units door to not close properly. secured door seal and tested. all ops test good. left litmus
We serviced a
JENNAIR RANGE
Model JJW2727DS00
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
03/19/2024
"Power plug case was cracked, replaced. Unit check ok charged service call. $179.95 CC Auth# 9R9M3F disclosed survey to cust fcc 5star."
We serviced a
SAMSUNG RANGE
Model NX58H5600SS/AA
Near Peyton, CO 80831
Jerimiah
Job Details:
03/19/2024
"Bake igniter weak, needs replacing. Cust holding off on repairs, will check out new appliances. Labor will be $189.95 upon return service. Total is $438.30 before labor. $142.95 CC Auth# W943HFDG94-00520A bake igniter $271.58"
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Albuquerque, NM 87105
Larry
Job Details:
03/19/2024
Installed ignitor and tested good - Unit is good to go
We serviced a
SAMSUNG REFRIGERATOR
Model RS28A500AS
Near Pueblo, CO 81005
Domingo
Job Details:
03/19/2024
Found white calcium in front and underneath refrigerator. I check evap condensation line and it was clear I check water filter but they are not using ice maker so there's no water connected at all check and clean condenser it had some water I vacuum out. I call tech line and Chris said to clean it and monitor
We serviced a
AMANA WASHER
Model NTW4519JW
Near Pueblo, CO 81004
James
Job Details:
03/19/2024
found suspension missaligned in bracket causing tub to tilt. secured and tested. all ops test good. left litmus
We serviced a
GE RANGE GAS
Model PGP9830SJ1SS
Near Colorado Springs, CO 80906
Jerimiah
Job Details:
03/19/2024
"Back right burner constantly emitting gas, needs gas valve replaced. Customer holding off on repairs. Labor will be $189.95 upon return service if chosen to do so.WB21X10052 BR burner valve $296.24"
We serviced a
SUB ZERO ICEMAKER
Model n/a
Near Colorado Springs, CO 80919
Ralph
Job Details:
03/19/2024
"unplugged unit and turned water off to unit, also gave cust some appliance info for other units in home...autho no. W9HA9L"
We serviced a
FRIGIDAIRE DISHWASHER
Model LFID2426TF2AI
Near Colorado Springs, CO 80904
Roman
Job Details:
03/19/2024
"Ran the dw and it would not drain, fills and sprays great. Took the pump out and found seeds and a screw inside. Labor $99.95Sc $129.95Total cost $229.95Paid sc labor check $221.95 CK Auth# 3WXFAU"
We serviced a
THERMADOR WINE COOLER
Model T24IW900SP/03
Near Colorado Springs, CO 80919
Ralph
Job Details:
03/19/2024
INSTALLED PARTS AND UNIT CHECKED OKAY
We serviced a
SAMSUNG DRYER
Model DV476ETHAWR/A1
Near Colorado Springs, CO 80906
Roman
Job Details:
03/19/2024
"Ran the dryer and its not heating up, recommend replacing the heater assy. Heating assy #DC97-14486A 282.50Tax $23.17Parts total $305.67MPs $14.50Labor $189.95Sc $129.95 Total cost $640.07 Paid sc check $129.95 CK Auth# XR4T33"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Rio Rancho, NM 87144
Joe
Job Details:
03/19/2024
"cx complaint - water begins to fill. we can hear it running, it stops, - inspected un it - bad sump - customer declinded repair"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ1
Near Albuquerque, NM 87120
Larry
Job Details:
03/19/2024
CX complaint - Not cooling properly - Inspected unit and found the RC at 35.7 and the FC at -1.3 - Unit seems to pe operating as designed at this time
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, CO 80919
Glenn
Job Details:
03/19/2024
"leaking water underneath. No water stains under unit. Filled unit with 1/2 gallon of water > Drained > No Leaks , Fill Unit using Bulky cycle, No Leaks, Ran Drain > Found Water leaking from inside wall where drain is located. Stopped machine by unplugging unit, turned water off, Unit has over half tub filled still inside, suggest leave water inside tub until drain fixed. Not covered under warranty, Paid SC Fee of $129.95, Autho #CHXTPM"
We serviced a
THERMADOR DOUBLE WALL OVEN
Model MEDMC301WS/04
Near Colorado Springs, CO 80906
Ralph
Job Details:
03/19/2024
INSTALLED PART AND UNIT CHECKED OKAY
We serviced a
SAMSUNG DRYER
Model DV42H5600EP/A3
Near Colorado Springs, CO 80922
Mathew
Job Details:
03/19/2024
"Replaced tensioner, test op all okay. Paid labor 179.95. $179.95 CC Auth# 4W44LJ"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDEM01
Near Colorado Springs, CO 80922
Jessie
Job Details:
03/19/2024
Replaced listed parts and ran bulletin . All ok
We serviced a
MARVEL ICEMAKER
Model MACP215-SS01B
Near Colorado Springs, CO 80906
Jessie
Job Details:
03/19/2024
Unit is leaking out of drain pump and broken water line. Unit has a bad inverter. Waiting on dispatch from company.
We serviced a
MAYTAG DRYER
Model MEDB835DW1
Near Colorado Springs, CO 80925
Carlos
Job Details:
03/19/2024
"Installed repair kit, runs ok cx paid in full $375.70 CC Auth# 33K3NH"
We serviced a
GE REFRIGERATOR BOT
Model GFE29HGDHBB
Near Colorado Springs, CO 80918
Kris
Job Details:
03/19/2024
rc temp@43.5 fc temp@0.4 ran test op all fans and defrost are working temp is within a few degrees of set temp. cx will monitor unit.WR17X13170
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Fountain, CO 80817
Carlos
Job Details:
03/19/2024
Installed basket
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KWH1
Near Peyton, CO 80831
Aaron
Job Details:
03/19/2024
"Removed and replaced components, tested unit for 15 minutes, no leaks and working well now, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM02
Near Colorado Springs, CO 80911
Carlos
Job Details:
03/19/2024
"Installed gasket, all ok"
We serviced a
MAYTAG REFRIGERATOR
Model MSS26C6MFZ00
Near Monument, CO 80132
Kris
Job Details:
03/19/2024
wires are pinched in door. will need to replace door to resolve issue.
We serviced a
BOSCH FRENCH DOOR REFR
Model B36CD50SNS/06
Near Monument, CO 80132
Kris
Job Details:
03/19/2024
installed ice maker and all parts sent ran test op all ok at this time cx will monitor unit. .
We serviced a
WHIRLPOOL WASHER
Model MVW6200KW2
Near Peyton, CO 80831
Aaron
Job Details:
03/19/2024
"Removed and replaced suspension, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG RANGE
Model NE59J7630SG/AA
Near Colorado Springs, CO 80907
Brandon
Job Details:
03/19/2024
"Oven not reaching set temp checked using thermocouple, checked power at terminal block, only getting 213 volts on stand by and voltage drops to 209 volts when under load, need minimum 220 volts for unit to heat properly, found L1 loose at terminal block tightened, all other checks ok, Svf paid $89.95 Auth# 33V99N"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM06
Near Colorado Springs, CO 80922
Aaron
Job Details:
03/19/2024
"Scratches and dents on both doors, removed and replaced doors,no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
SAMSUNG DISHWASHER
Model DW80M9550UG/AA
Near Colorado Springs, CO 80907
Brandon
Job Details:
03/19/2024
"Found spray arm disconnected from vane assy, reattached and secured arm, tested op all checks ok, Svf paid $129.95 Auth# 33V99N"
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5100MTAA
Near Colorado Springs, CO 80904
Brandon
Job Details:
03/19/2024
"Replaced compressor and dryer, vacuumed unit for 10 minutes, held vacuum for 10 minutes, charged unit to spec, hass oqc passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5241SR/AA
Near Colorado Springs, CO 80905
Brandon
Job Details:
03/19/2024
"Ice maker broke need new ice maker, replaced ice maker and cycled all checks ok"
We serviced a
KITCHENAID DISHWASHER
Model KUDC10FX
Near Colorado Springs, CO 80906
Ralph
Job Details:
03/19/2024
"CUST WORRIES O FTHE UNIT LEAKING, SAW NO SIGNS OF WATER TODAY, BELEIVE ISSUE MAY BE WITH HOW DISHES ARE PLACED, XCUST TO TRY A FEW THINGS IVE EDUCATED HIM ABOUT. AUTHO NO. VJ93C9"
We serviced a
SAMSUNG MICROWAVE
Model ME11CB751012AA
Near Palmer Lake, CO 80133
Mathew
Job Details:
03/19/2024
"Replaced noise filter and wiring. Test op with cup of water, all good."
We serviced a
WHIRLPOOL WALLOVEN
Model WOS51EC0HS20
Near Rio Rancho, NM 87124
Joe
Job Details:
03/19/2024
cx complaint - oven not in proper place - raised oven - tested unit - unit good to go
We serviced a
SAMSUNG REFRIGERATOR
Model RF28JBEDBSG/AA
Near Monument, CO 80132
Mathew
Job Details:
03/19/2024
"Defrosted room, replaced all parts and test op all okay."
We serviced a
KENMORE RANGE
Model WFC310S0AW0
Near Rifle, CO 81650
James R
Job Details:
03/19/2024
Signed disclaimer. Replaced R.F. switch and knob. Tested ops ok. . customer paid labor $149.95 auth code334CV3
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA
Near Colorado Springs, CO 80907
Carlos
Job Details:
03/19/2024
Installed tracks all ok
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW2
Near Colorado Springs, CO 80907
Carlos
Job Details:
03/19/2024
"Ran test, reset control board runs all ok, advised cx to use a surge protector in their wall outlet. CX paid SC $129.95 CK Auth# 4HFJ43. Cx will observe."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Santa Fe, NM 87508
Jason
Job Details:
03/19/2024
Unit is in one of Pulte's model homes and hasnt been used or sold. when arrived unit was un-plugged ran full diagnostic cycle no codes present all opperations check ok at this time
We serviced a
WHIRLPOOL WALLOVEN
Model WOD77EC0HS20
Near Colorado Springs, CO 80922
Aaron
Job Details:
03/19/2024
"Time and date intermittently resetting, removed and replaced console assembly, programmed and tested unit, working well now. Advised customer of 5 star survey."
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Silt, CO 81652
Erik
Job Details:
03/19/2024
replace heater and front panel assembly.verify operation . all good job complete
We serviced a
JENN-AIR COOKTOP
Model JIC4715GS00
Near Los Alamos, NM 87544
Jason
Job Details:
03/19/2024
SR7738714338 Spoke to techline they said that touch area has to be really clean unit is working if issue comes back ui will be needed
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Colorado Springs, CO 80924
Aaron
Job Details:
03/19/2024
"Removed and replaced gasket and motor sump assembly, tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL DOUBLE WALL OVEN
Model GBD309PVS02
Near Colorado Springs, CO 80924
Aaron
Job Details:
03/19/2024
"Tested both oven cavities at 350f bake cycles, average temperature for upper oven 324f, lower 322f, unit would need oven sensors and control, calibrated both cavities +30f, control is no longer available. Sensor wpw10131825 $122.82 ?2 sensors= $245.64Control 8303018 NLAAuth 129.95 hc #HYNJ94"
We serviced a
GE REFRIGERATOR/TOP
Model GTS22KYNBRFS
Near Rifle, CO 81650
Erik
Job Details:
03/19/2024
"Replace lowwer door gasket and replace defrost heater, level unit. verify operation. all good. job complete"
We serviced a
GE WASHER
Model GFW550SSN5WW
Near Carbondale, CO 81623
Erik
Job Details:
03/19/2024
repoplace motor and inverter. verify operation. al good order complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRTX5028PM00
Near Santa Fe, NM 87507
Jason
Job Details:
03/19/2024
installed evaporator and compressor unit checks ok
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Aspen, CO 81611
Erik
Job Details:
03/19/2024
replace terminal block and whip.splice L1 connector see quick pics . test operation.job complete
We serviced a
GENERAL ELECTRIC DRYER
Model HTX24EASK0WS
Near Glenwood Springs, CO 81601
Erik
Job Details:
03/19/2024
replace heater and TCO. verify operation all good. job completecx not available for signature
We serviced a
KITCHENAID RANGE
Model KFGC506JSS01
Near New Castle, CO 81647
James R
Job Details:
03/19/2024
Customer signed disclaimer. Replaced R.F flame spreader and R.R. burner head and electrodes / igniters for each. Test operation are lighting good. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Breckenridge, CO 80424
Antonio
Job Details:
03/19/2024
Installed new icemaker and ui panel unit tested good
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS00
Near Colorado Springs, CO 80919
Glenn
Job Details:
03/19/2024
"Install LED Module Kit, All OPS Test:OK"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW10
Near Rio Rancho, NM 87124
Larry
Job Details:
03/19/2024
installed parts listed and tested good - Unit is good to go - Servey mentioned
We serviced a
SAMSUNG WASHER
Model WA50R5200AWUS
Near Colorado Springs, CO 80918
Mathew
Job Details:
03/19/2024
"Found spin basket wobbling when empty, ub ur codes stored. Unit is level, dampers look good. Recommend a new spin basket. Svf 129.95PartsMPs 14.50DC90-27205B 530.87 + 43.53 tax Labor 259.95 Cx not moving forward with repair. $129.95 CC Auth# 39U4J3"
We serviced a
JENN-AIR REFRIGERATOR BOT
Model JFFCC72EFS00
Near Colorado Springs, CO 80919
Glenn
Job Details:
03/19/2024
"Ice clumping together in center of bucket and freezing into solid block of ice, which then creates problem with auger and not dispensing ice. IM Harvest Test > Pass , Fill Test > Pass. Water hold test in chute > Pass, Found cracks in icemaker mold. Also RS Door Gasket is torn.Icemaker - W10908387 $199.70 ,Gasket (RS) - W10917313 $192.62 , Valve - W11535162 $104.66 , Tax $40.75 , MPS $14.50 , SC Fee $149.95 , Labor $279.95 , Customer is going to watch for water leaking out into bucket, to determine if its from crack in IM mold, or Valve, then call us. Paid SC fee of $149.95 , Autho#9RU9M3"
We serviced a
WHIRLPOOL DRYER
Model WED4950HW
Near Colorado Springs, CO 80909
Carlos
Job Details:
03/19/2024
Installed listed parts all ok
We serviced a
WHIRLPOOL WASHER
Model MVW7230HC1
Near Rio Rancho, NM 87144
Larry
Job Details:
03/19/2024
Installed parts listed and tested good - Unit is good to go - Servey mentioned
We serviced a
SAMSUNG WASHER FRONT LOA
Model WF331ANR/XAAI
Near Monument, CO 80132
Kris
Job Details:
03/19/2024
ran test op found impeller on drain pump stuck cleared ran test op all ok.
We serviced a
MAYTAG DRYER
Model MED7230HW1
Near Colorado Springs, CO 80920
Glenn
Job Details:
03/19/2024
"Install New T-stats, All OPS Test:OK"
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC2
Near Colorado Springs, CO 80920
Glenn
Job Details:
03/19/2024
"F6E3 - Communication Error: ACU Cannot Hear UIF0E3 - OverloadF2E1 - UI Stuck Indicates that the user interface is detecting that a button is Button continuously activated.Bad UI Console, Possible Bad Main PCB as well. , UI Console - W10838672 $316.07, Main Control - W10812418 $305.20 , Tax $50.94 , MPS $14.50 , SC Fee $149.95 , Labor $179.95. Declined Estimate, wants to buy new washer. Paid SC Fee of $149.95 , Autho# 9M9MN4"
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS1
Near Colorado Springs, CO 80920
Glenn
Job Details:
03/19/2024
"All OPS Test: OK, Ran Several Diag Tests > No Leaks. Possible Loading or Soap Overdose issue. Customer will continue to monitor."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS2
Near Colorado Springs, CO 80918
Glenn
Job Details:
03/19/2024
Lower spray arm was laying in bottom of tub and melted on element during cycle. element appear to be fine. Install New Lower Spray-arm. Diag Test > Pass
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT348FMES04
Near Breckenridge, CO 80424
Antonio
Job Details:
03/19/2024
Installed new compressor unit tested good
We serviced a
GE DISHWASHER
Model PDW7880N20SS
Near Colorado Springs, CO 80923
Kris
Job Details:
03/19/2024
ran test op too many parts nla.
We serviced a
ZEPHYR RANGE HOOD
Model AK7636BS
Near Colorado Springs, CO 80924
Jessie
Job Details:
03/19/2024
Replaced broken control. Test op. All.ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near New Castle, CO 81647
James R
Job Details:
03/19/2024
Customer signed disclaimer.Very little water. Replaced valve and filter housing. Tested waterflow with filter out. It is working as should. Installed filter they had have very little water flow filter is plugged. Customer needs to replace filter again. They indicated they has replaced filter before. Left filter out. test cycled icemaker cycled fine and filled with water. operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Basalt, CO 81621
James R
Job Details:
03/19/2024
Siogned disclaimer. Vent behind unit is kinked. When pulled out from wall do have some air flow but is still restricted. Checked with manometer. .80 max is .56 so it is over the allowable restriction. This will definitely affect the drying of the unit. Unhooked the venting from the unit and checked the heat cycling cycle. Hi 170 Lo 130 good let cycle several times it is working as should. Needs to have company out that can clean and take care of restrictions. Customer paid service call $149.95 auth code. LE4M9F
We serviced a
FRIGIDAIRE RANGE
Model TEF351EWB
Near Rifle, CO 81650
James R
Job Details:
03/19/2024
Signed disclaimer. Replaced bake element. Test op's ok. Customer paid service call $99.95 auth code NNR394Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
ASKO DRYER
Model TD11 ART 10771110
Near Woodland Park, CO 80863
David
Job Details:
03/19/2024
"Checked dryer, found a bunch of lint in the blower housing and wheel, removed lint. The drum rollers are going bad and are no longer available. Cx is going to run it till it quits."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ01
Near Edgewood, NM 87015
Jason
Job Details:
03/18/2024
installed control unit checks ok
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS0
Near Avon, CO 81620
Antonio
Job Details:
03/18/2024
Installed drain pump unit tested good
We serviced a
BOSCH FRENCH DOOR REFR
Model B36CT80SNS/09
Near Avon, CO 81620
Erik
Job Details:
03/18/2024
install doors on siteJOB COMPLETECX not available for signature
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ00
Near Santa Fe, NM 87507
Jason
Job Details:
03/18/2024
installed part unit checks ok
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Rifle, CO 81650
James R
Job Details:
03/18/2024
Printed labels took pics ready to send.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Pueblo, CO 81001
Domingo
Job Details:
03/18/2024
Found out the duct was disconnected from the main venting told customer needs hvac person but dryer is working correctly and clean
We serviced a
SAMSUNG REFRIGERATOR
Model RF28N9780SR/AA
Near Colorado Springs, CO 80924
Brandon
Job Details:
03/18/2024
"Unit not cooling at all, called tech support did visual support, we need to make a new Samsung ticket to get the 7000#, hass oqc passed"
We serviced a
MIDEA WASHER
Model MLH52S7AWW
Near Pueblo West, CO 81007
James
Job Details:
03/18/2024
found counterweight loose causing vibration when spinning. tightened down and tested all ops test good
We serviced a
THERMADOR DOUBLE WALL OVEN
Model PODMC301W/05
Near Colorado Springs, CO 80921
Kris
Job Details:
03/18/2024
installed door ran test op all ok at this time unit is working to spec at this time.
We serviced a
AMANA DRYER
Model NED4655EW
Near Colorado Springs, CO 80910
Carlos
Job Details:
03/18/2024
"Installed blower and motor, runs ok"
We serviced a
BOSCH DISHWASHER
Model SGX78B55UC/38
Near Colorado Springs, CO 80921
Kris
Job Details:
03/18/2024
reset unit. ran test op all ok at this time unit is working to spec at this time.
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Edgewood, NM 87015
Jason
Job Details:
03/18/2024
gfci is nuisance tripping per techline range checks ok SR7738705858 called safety sr7738666367
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Albuquerque, NM 87123
Jason
Job Details:
03/18/2024
"checked unit found compressor was out of its mounts, re mounted compressor unit checks ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT705PAKZ0
Near Albuquerque, NM 87111
Jason
Job Details:
03/18/2024
installed drain pump made sure line is clear unit checks ok
We serviced a
JENNAIR RANGE
Model 88370
Near Colorado Springs, CO 80904
Carlos
Job Details:
03/18/2024
Needs a bake element. part is discontinued. Cx paid $169.95 CC Auth# 44K9LC
We serviced a
MAYTAG WASHER
Model MVWC465HW3
Near Pueblo West, CO 81007
James
Job Details:
03/18/2024
fpund loose wire at drain pump causing unit to not run. secured and tested. all ops test good
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Colorado Springs, CO 80925
Mathew
Job Details:
03/18/2024
Replaced control assy. Test op all okay.
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Rio Rancho, NM 87144
Joe
Job Details:
03/18/2024
cx complaint - not operating or won't start - inspected unit - found plug loose for latch at control - fixed plug - tested unit - unit good to go - advised about survey