We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Newport, Oregon 97365
Nathan
Job Details:
02/19/2026
Gasket on rear of tub was folded in many places I removed top and front and slid tub forward and fixed folds on rear gasket.No warping or denting in tub or rear bulkhead Reinstalled and tested No noise- unit heats and tumbles Advised of survey
We serviced a
GE REFRIGERATOR/TOP
Model PWE23KYNIFS
Near Lincoln City, Oregon 97367
Nathan
Job Details:
02/19/2026
Compressor fired up and is not loud and is pumping and cooling
We serviced a
PROFILE WASHER/DRYER COM
Model PFQ97HSPVODS
Near Silt, Colorado 81652
Clint
Job Details:
02/19/2026
Customer signed disclaimer and recieved parts .took unit apart and installed all parts ordered. Ran through diagnostic test and everything ran perfectly. Spins and drains well. PLEASE TAKE TECH SURVEY THANKS.CLINT.
We serviced a
SAMSUNG RANGE
Model NX60A6511SS/AA
Near Pueblo, Colorado 81001
Domingo
Job Details:
02/19/2026
Cx cancelled
We serviced a
SAMSUNG RANGE
Model NSE6DG8100SRAA
Near Pueblo, Colorado 81001
Domingo
Job Details:
02/19/2026
Replaced main pcb ui test it and it worked
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC
Near Santa Fe, New Mexico 87505
Tye
Job Details:
02/19/2026
Arrived and cx complaint of noisy when stopping spin. Found the stator bolt had vone out. Replaced bolt with loc tite. Checked unit operation. Washer is functioning now as designed. No further issues noted. Informed cx of review process
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ19
Near Santa Fe, New Mexico 87505
Tye
Job Details:
02/19/2026
Arrived and cx complaint of not freezing things like ice cream. The unit is in the garage and temps in garage are aprox 30 degrees. Unit is satisfied with garage being cold. Won't run if thermostat is sat.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Santa Fe, New Mexico 87505
Tye
Job Details:
02/19/2026
Cx complaint of not drying properly. Found the vent hose was kinkedand element had failed. Replaced heating element and tested unit. Dryer is functioning as designed now. No further issues noted. Informed cx of review process
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9671SR/AA
Near Redmond, Oregon 97756
Richard
Job Details:
02/19/2026
Installed new icemaker and water filter. Housing assembly cycle tested water going into dispenser no problems do you not working as designed at this time job
We serviced a
WHIRLPOOL RANGE
Model WFES5030RZ0
Near Winter Park, Colorado 80482
Antonio
Job Details:
02/19/2026
"Found no issues wire harness, cntrl all good smoke was from first burn off"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW3
Near Fraser, Colorado 80442
Antonio
Job Details:
02/19/2026
Installed new pump and dispenser then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL WALL OVEN
Model WOC54EC0HS04
Near Granby, Colorado 80446
Antonio
Job Details:
02/19/2026
Installed new maga and inverter then proceeded to heat a cup of water and new mag plew out aswell called tech line case#22596242 unit is no longer repairable per whlp
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MW0
Near Trinidad, Colorado 81082
James
Job Details:
02/19/2026
"Found igniter wire shorted replaced with pre-ordered parts test it Ops, alll check OK."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5201SR/AA
Near Fountain, Colorado 80817
Brandon
Job Details:
02/19/2026
"Replaced pcb, compressor and drier, tested operation all checks ok"
We serviced a
MAYTAG WASHER
Model MVW5435PW0
Near Grand Lake, Colorado 80447
Antonio
Job Details:
02/19/2026
"Installed new water valve cam, and belt then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey"
We serviced a
MONOGRAM REFRIGERATOR
Model ZIC303NPPBII
Near Parshall, Colorado 80468
Erik
Job Details:
02/19/2026
no instaruction on problem/ unit not yet installedplease confirm why dispatched for repair?
We serviced a
WHIRLPOOL WALL OVEN
Model WOC54EC7HW22
Near Edgewood, New Mexico 87015
Jason
Job Details:
02/19/2026
Installed console checked unit operation checks ok. spoke to cx about review
We serviced a
WOLF WALL OVEN
Model DO3050PM/S/P
Near Colorado Springs, Colorado 80920
Charles
Job Details:
02/19/2026
Replaced halogen lamp
We serviced a
GE MICROWAVE
Model SCB1001KSS 01
Near Colorado Springs, Colorado 80921
Charles
Job Details:
02/19/2026
"Unit is GE Profile Advantium 120, manufactured in 2006, arcing from magnetron, waveguide damage, unit is not repairable. See photos"
We serviced a
MAYTAG WASHER
Model MVWB765FW1
Near Eagle Point, Oregon 97524
Chris
Job Details:
02/19/2026
"Replaced the control board, control panel and suspension rods. Tested"
We serviced a
SUBZERO REFRIGERATOR
Model 550 - RH
Near Beaverton, Oregon 97006
Austin
Job Details:
02/19/2026
2/19/26 AB: remove and replaced freezer and fridge door gaskets. Tightened door handle and cleared blockage From drain hose. Service is complete
We serviced a
MAYTAG WASHER
Model MVW7230HC0
Near Rio Rancho, New Mexico 87144
Larry
Job Details:
02/19/2026
Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
ELECTROLUX DRYER
Model ELFE7738AW
Near Bend, Oregon 97701
Levi
Job Details:
02/19/2026
Customer is complaining of lots of vibration noise coming from dryer. Some of the noise was coming from the rear exterior panel so I tightened all screws in th back and most I'd not all the noise has gone. Customer is still not happy with the noise coming from the seam on the drum and I informed her I could replace the drum but the new drum could be noisier then this one. What she is hearing is the seam of the drum going over the rollers and I told her overall it's pretty quiet compared to most dryers.
We serviced a
WHIRLPOOL WASHER
Model WTW4307SW0
Near Eagle Point, Oregon 97524
Chris
Job Details:
02/19/2026
Ran a test cycle with no error codes. No error codes stored. Washer is working normally.
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Lincoln City, Oregon 97367
Nathan
Job Details:
02/19/2026
Replaced inoperable condenser fan motor Tested Advised of survey
We serviced a
FRIGIDAIRE DISHWASHER
Model FDPC4221AW3A
Near Lincoln City, Oregon 97367
Nathan
Job Details:
02/19/2026
"Unit pulled from no electrical No plumbing No water I supplied power via but 3 prong extension cord,With pump in hand it turns and spins no obstructions All signs point to unit would drain in proper plumbing situation Tested Advised of survey"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model PRFC2383AFJ
Near Bend, Oregon 97701
Levi
Job Details:
02/19/2026
"Replace ice maker, tested and all checks okay"
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ0
Near Albuquerque, New Mexico 87120
Larry
Job Details:
02/19/2026
Installed parts lsited and tested good - Uit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Rifle, Colorado 81650
Clint
Job Details:
02/19/2026
Customer signed disclaimer and recieved pump and control. Installed parts programmed control and ran a quick wash cycle. No leaks detected and spin and agitate ran perfectly. PLEASE TAKE TECH SURVEY.THANKS CLINT.
We serviced a
MAYTAG DRYER
Model MEDB835DW4
Near Pueblo, Colorado 81004
James
Job Details:
02/19/2026
Found open heating element installed pre-ordered parts tested ops all ckok
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Albuquerque, New Mexico 87112
Jason
Job Details:
02/19/2026
Checked unit found cam had failed installed cam and belt. ran quick cycle unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ19
Near Albuquerque, New Mexico 87121
Larry
Job Details:
02/19/2026
CX complaint - Not cooling properly - Inspected unit and found the condenser covered with dust and debris and the space the unit is in very tight - Cleaned condenser and properly spaced away from rear wall to allow better ait circulation - Unit should be good to go - Survey mentioned
We serviced a
GE REFRIGERATOR
Model GDE25EYKJRFS
Near Carbondale, Colorado 81623
Sean
Job Details:
02/19/2026
Verified information customer signed disclaimer.Checked the units ice maker. Found the fill tub is freezing up. I cleaned the ice off of the fill tube and tested the ice maker it is working as designed.Removed the fill tube and adjusted it . Found the ice maker was not leveled so I adjusted it. Put the unit back and tested the ice maker it successfully went through the motions and filled with water.Tested good.
We serviced a
BOSCH RANGE
Model HGS8655UC/04
Near Carbondale, Colorado 81623
Sean
Job Details:
02/19/2026
Pulled the unit out and Removed the burners and top assembly Installed the new top assembly and burners and reassembled the unit .Tested good.Thank you.please fill out a technician survey
We serviced a
SUBZERO FREEZER
Model DEC2450FI/L
Near Colorado Springs, Colorado 80921
Charles
Job Details:
02/19/2026
"Condenser overheating and airflow blocked, Condenser error in memory, clear codes, clean condenser. Customer to monitor. Service fee $169.95, Labor $120.95, Total $290.90 paid autho 99VXJN"
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Aspen, Colorado 81611
James R
Job Details:
02/19/2026
Signed disclaimer. Replaced valve cold wtr side was bad. Test operation. Is working as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DRYER
Model WED5100HC4
Near Roseburg, Oregon 97471
Chris
Job Details:
02/19/2026
Replaced the control board and moisture sensor wire harness and tested.
We serviced a
WHIRLPOOL DRYER
Model WED4105SW1
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
02/19/2026
UI panel wire was disconnected from main control board. Runs and heats ok
We serviced a
LG DRYER
Model DLEX3700W
Near Colorado Springs, Colorado 80908
David
Job Details:
02/19/2026
"Checked lg dryer, had CL code flashing on display and not starting. CL is control lock, turned off and machine is running."
We serviced a
LG REFRIGERATOR
Model LRFS28XBS.ASTCNA2
Near Pueblo West, Colorado 81007
Domingo
Job Details:
02/19/2026
Replaced door no one was here but notice is missing the handle idk if the customer had it or if that was the part that was broken because door didnt come with handle but other than that door has been replaced
We serviced a
GE WASHER
Model GTW465ASN9WW
Near Otis, Oregon 97368
Nathan
Job Details:
02/19/2026
Unit had no error codes Reset unit to factory Did a calibration cycle Tested through speed wash with no issues Advised of survey
We serviced a
KITCHENAID DISHWASHER
Model KDTM704LPAO
Near Snowmass, Colorado 81654
James R
Job Details:
02/19/2026
Signed disclaimer. Replaced pump motor assy. Finished assembling unit and installing. Run unit is operating as designed and could see no leaks. Put a leak board under unit and took pic. Please fill out tech satisfaction survey. Thank You.
We serviced a
GE DISHWASHER
Model GDF610PMJ5ES
Near Fraser, Colorado 80442
Erik
Job Details:
02/19/2026
ACCESS WITH LOCK BOX CODECONNECT TO SMARTHQ SERVICE:*see quick picsALERT PRESENT! ABNORMAL CONRTOL RESET CONDITIONSAPPLY FIRMWARE UPDATE/ TEST: PASSNOTES FOR C/B: FOLLOWING ALERT: IF PROBLEM PERSISTS - REPLACE MCB/ UI/ HARNESSSEND BILL TO CX VIA IWALLET $282.95 SERVICE FEE
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Santa Fe, New Mexico 87507
Tye
Job Details:
02/19/2026
Arrived and cx complaint of not working right. Dead. Removed control panel and removed failed control installed new control. Unit is functioning now as designed. No further issues noted. Informed cx of review process.
We serviced a
WHIRLPOOL RANGE
Model WFG505M0MS0
Near Albuquerque, New Mexico 87111
Jason
Job Details:
02/19/2026
Checked unit flame for bake checks ok. adjusted surface burner heights. unit operates as designed at this time. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHV06
Near Grand Lake, Colorado 80447
Antonio
Job Details:
02/19/2026
"Installed new compressior, evaporator and drier then i charged unit with r600 and unit is working properly also advised cx of whlp survey"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF3136SZ00
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
02/19/2026
"Tapped into the sealed system, -16 low side and 75 high side, amp draw of .47, unit settled at +4, charged unit with nitrogen past 160 pounds and monitored, drop to 159 after 45 minutes, used leak detector on connections, discussed situation with techline, sent for review, whirlpool to reach out to the customer . Advised customer of situation and survey. Case number 226006"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Albuquerque, New Mexico 87110
Jason
Job Details:
02/19/2026
Installed control. ran calibration and quick wash cycle. unit operation checks ok. spoke to cx about review
We serviced a
GE RANGE
Model JBS86SP6SS
Near Monument, Colorado 80132
Charles
Job Details:
02/19/2026
Replaced front left element
We serviced a
WOLF COOKTOP
Model ci304c/b
Near Portland, Oregon 97217
Austin
Job Details:
02/19/2026
2/19/26 AB: CC glass top is damaged and will need to be replaced. Tech uninstalled the unit and replaced the glass top. Tested unit and found no further issues. Cleaned up surrounding area for any glass and cleared out below cabinetry.
We serviced a
WHIRLPOOL WALL OVEN
Model WOEC3030LS
Near Monument, Colorado 80132
Mathew
Job Details:
02/19/2026
"Replace parts, issue persists. Sr#22597943 ran thru unit with techline. Found neutral to ground carrying 120v. Recommend a licensed electrician come and check out wiring on house, as neutral should not carry voltage."
We serviced a
GE REFRIGERATOR/TOP
Model HPS10LSVBRSS
Near Granby, Colorado 80446
Erik
Job Details:
02/19/2026
ACCESS WITH CODES FROM CXINSTALL GASKET SETJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
GE DRYER
Model PFD87ESSV0WW
Near Glenwood Springs, Colorado 81601
Sean
Job Details:
02/19/2026
Verified the unit customer signed disclaimer.Checked the unit and removed the control and top panel.Looked at the water valve . Tested found that the brum filled with cool water.Checked the water lines and found that the hot and cold water had been switched. I switched the water lines to the correct location.Tested the unit and it is not leaking anymore.Tested the unit good.Thank you.
We serviced a
JENN-AIR RANGE
Model JES1750FS1
Near Colorado Springs, Colorado 80918
Ralph
Job Details:
02/19/2026
"BELIEVE THE ISSUE CUST WAS EXPERIENCING WAS A STUCK KEY, BUT TODAY EVERYTHING IS WORKING CORRECTLY...AUTHO NO. MLPKR3"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS01
Near Colorado Springs, Colorado 80919
Charles
Job Details:
02/19/2026
Replaced ice maker valve
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
02/19/2026
Installed control board ran calibration and tests runs all ok
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Albuquerque, New Mexico 87110
Jason
Job Details:
02/19/2026
Checked unit found unit is one that has drain pump running continously per service pointer S153EB installed control ran calibration and quick wash unit operation checks ok. spoke to cx about review; used 1 W11603811 (control) from stock
We serviced a
PROFILE RANGE
Model PSS93YP3FS
Near Granby, Colorado 80446
Erik
Job Details:
02/19/2026
REPLACE MAIN TOPJOB COMPLETE
We serviced a
GENERAL ELECTRIC WASHER
Model PFW955SPW0DS
Near Redmond, Oregon 97756
Richard
Job Details:
02/19/2026
Installed parts ordered by previous tech cycled unit all tested fine
We serviced a
MAYTAG DRYER
Model MED7230HC3
Near Santa Fe, New Mexico 87507
Tye
Job Details:
02/19/2026
"Arrived and cx complaint of not working, won't turn on. Checked for proper voltage. 250, 120,120. Good. Took dryer apart and checked all fuses. All good. Took control board out and checked for broken wires ,all good. Put dryer all back together and unit is now working. No further issues noted. Informed cx of review process."
We serviced a
SAMSUNG WASHER
Model WA52DG5500AWUS
Near Pueblo West, Colorado 81007
Domingo
Job Details:
02/19/2026
Replaced lid lock and ran hass and it passed
We serviced a
WHIRLPOOL WASHER
Model MVWX655DW2
Near Colorado Springs, Colorado 80920
Earl
Job Details:
02/19/2026
"Customers, complaint unit, making loud noises.\nWe found that he had the upper retainer ring already here, but he had a screw that was stripped.We got it out reattached, it checked.The unit is operating properly up this time"
We serviced a
CAFE RANGE
Model CHS950P2M1S1
Near Palmer Lake, Colorado 80133
Earl
Job Details:
02/19/2026
"Installed the new sensor fan and board.We ran the units, both upper and lower ovens to 400? unit.Continue to run at this point.It seems that the unit is operating properly at this time"
We serviced a
ELECTROLUX REFRIGERATOR
Model ERFG2393AS7
Near Larkspur, Colorado 80118
Earl
Job Details:
02/19/2026
I drilled the stopper at the bottom of the nozzle and tested it unit is operating properly.At this time
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
02/19/2026
"Installed harness, control board and motor runs all ok"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80907
Carlos
Job Details:
02/19/2026
"Installed belt , cam and control ran test and calibration runs all ok"
We serviced a
SAMSUNG WASHER
Model WF45B6300AW/US
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
02/19/2026
"Install damper kit. Test op, unit working as expected. Cx states washer has been shaking the entire house while in spin, washer is on third floor. Washer is level, recommend Cx film washer malfunctioning, including what cycle is being used and what is in the washer."
We serviced a
SAMSUNG DISHWASHER
Model DW80M2020US
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
02/19/2026
Found evidence of leak underneath drain pump. Recommend drain pump assy. $149.95 CC Auth# N9HWN4Svf $149.95
We serviced a
MAYTAG WASHER
Model MTW7405RR1
Near Colorado Springs, Colorado 80917
David
Job Details:
02/19/2026
"Installed ordered parts, ran calibration and diagnostic cycles. Running normal."
We serviced a
GE DRYER
Model GTD38EASW0WS
Near Colorado Springs, Colorado 80922
David
Job Details:
02/19/2026
"Replaced high limit, tested and is operating correctly."
We serviced a
KENMORE DRYER
Model 1108653511065
Near Colorado Springs, Colorado 80919
Earl
Job Details:
02/19/2026
"Customers complaint old drier not running. I arrived and I found the electrical cord was melted due to the heat I found the back panel was very, very blackened from the heating element not shutting off, opened it up the thermostat just fell off because it was melted. Most likely the views was bad as well.But the customer got a good look at it and said, no, we're just gonna replace this cause.It was in bad shape.Customer already paid.The service charge unit is going to be replaced"
We serviced a
SAMSUNG WASHER
Model WA52A5500AC/US
Near Colorado Springs, Colorado 80908
Mathew
Job Details:
02/19/2026
"Bobby pin in drain pump. Remove pin. Test op, unit working as expected. All okay. Collect and 149.95. $149.95 CC Auth# X4CEPC"
We serviced a
SAMSUNG RANGE
Model NSI6DG9900SRAA
Near Colorado Springs, Colorado 80923
Mathew
Job Details:
02/19/2026
Adjusted door. Cx is happy with stove. All okay.
We serviced a
WHIRLPOOL DRYER
Model WHD862CHC2
Near Basalt, Colorado 81621
James R
Job Details:
02/19/2026
"Signed disclaimer. Tore apart and replaced motor, bracket with idler pulley and installed the repair kit. Unit sounds fine and is heating. Unit is operating as designed. Please fill out tech satisfaction survey. Thank You."
We serviced a
WHIRLPOOL WALL OVEN
Model WOC75EC0HS22
Near Peyton, Colorado 80831
Aaron
Job Details:
02/19/2026
"Magnetron is arching in waveguide, inspected unit and found damaged waveguide, discussed situation with safety. Customer to contact whirlpool. Advised customer of situation and survey. Case number 22516307"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAHV0
Near Albuquerque, New Mexico 87106
Jason
Job Details:
02/19/2026
Checked unit installed drain pump. ran quick cycle unit operation checks ok.spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Carbondale, Colorado 81623
James R
Job Details:
02/19/2026
Has a F3E1 pressure system faultF7E5 Shifter faultF1E1 Main control faultCleared codes and replaced control. Per SP W11766193 Special Project S153EB Then calibrated it. Put thru a service test as well no issues. Belt is slipping. Customer is aware. Please fill out tech satisfaction survey. Thasnk You.
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS01
Near New Castle, Colorado 81647
James R
Job Details:
02/19/2026
Helped Clint remove unit from wall and tore apart to replace M/V turn table motor. Reassembled then installed. Unit is working as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
LG REFRIGERATOR
Model LRFS28XBS.ASTCNA2
Near Pueblo West, Colorado 81007
Domingo
Job Details:
02/19/2026
Replaced door no one was here but notice is missing the handle idk if the customer had it or if that was the part that was broken because door didnt come with handle but other than that door has been replaced
We serviced a
JENNAIR REFRIGERATOR
Model JBSS42E22L00
Near Florissant, Colorado 80816
David
Job Details:
02/18/2026
"Installed icemaker, cx to monitor."
We serviced a
MAYTAG WASHER
Model MFW7020RU0
Near Florissant, Colorado 80816
David
Job Details:
02/18/2026
"Installed ordered parts, ran diagnostics cycle, running smoother."
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS2
Near Cave Junction, Oregon 97523
Chris
Job Details:
02/18/2026
Replaced the drain pump and tested.
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EHL01
Near Monument, Colorado 80132
Ryan
Job Details:
02/18/2026
Replaced water inlet valve and defrosted water line. Tested icemaker good with no errors and tested fill good. Allow 24 hours for ice production. RK
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Divide, Colorado 80814
David
Job Details:
02/18/2026
"Installed ordered parts, ran diagnostic cycle, all good."
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPS02
Near Tijeras, New Mexico 87059
Jason
Job Details:
02/18/2026
Checked unit found filter had plugged up. installed another filter cx had re-tested unit unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Cedar Crest, New Mexico 87008
Jason
Job Details:
02/18/2026
Checked unit found that unit looks as though it may have overfilled but can not verify at this timeSC$184.95MPS$17.50LABOR$189.95FILL VALVE#WPW10327249$89.12TX$25.21TOTAL$506.73 Auth code: 99LRHT$184.95
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Medford, Oregon 97504
Thomas
Job Details:
02/18/2026
Replaced main control board and cycle switch. Calibrated washer. Ran tested okay with customer present. No leaks. Advised customer of survey
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Colorado Springs, Colorado 80904
Mathew
Job Details:
02/18/2026
Found c80 code. Remove venting. Found machine operating as expected. Recommend Cx get venting replaced and shortened to avoid future issues.
We serviced a
SAMSUNG REFRIGERATOR BO
Model RF4287HAWP
Near Colorado Springs, Colorado 80905
Mathew
Job Details:
02/18/2026
"Found evap assy completely frozen. Thaw out unit. Found clogged drain line. Clear drain line. Dry and defrost evap cover. Test op, fan still working, fridge cooling. All okay. Svf $149.95Labor $189.95Repair total $339.90$339.90 CC Auth# PF4N4T; (serial indicated as 'NotAvailable' so system created UIS w/pseudo #)"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
02/18/2026
"Capacitor is shorted out, removed and replaced, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo West, Colorado 81007
Domingo
Job Details:
02/18/2026
Replaced control calibrated control and ran diagnostic and it passed
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRFF5536RZ
Near Pueblo West, Colorado 81007
Domingo
Job Details:
02/18/2026
Check light and it wasnt connected connected light and light works
We serviced a
SUB-ZERO REFRIGERATOR
Model BI-36USTH-LH
Near Portland, Oregon 97236
Austin
Job Details:
02/18/2026
2/18/27 AB : removed and replaced old mother board and programmed new board per model tag. Unit is running and cooling. Advised customer proper times to put food back into unit. Service complete
We serviced a
KITCHENAID DISHWASHER
Model KDPS324SPS0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
02/18/2026
"Removed and replaced tub assembly, installed and tested unit through diagnostics, working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
GE REFRIGERATOR/TOP
Model GNE27JYMYFFS
Near Culver, Oregon 97734
Richard
Job Details:
02/18/2026
Install parts listed cycle tested unit all tested good at this time. Job complete customer is going to watch icemaker. Make sure continues to work properly.
We serviced a
GE DISHWASHER
Model PDP715SYV1FS
Near Culver, Oregon 97734
Richard
Job Details:
02/18/2026
Installed new control and drain pump and upper dish rack cycle tested unit all tested fine at this time.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS09
Near Sisters, Oregon 97759
Levi
Job Details:
02/18/2026
"Replaced ice maker and after installation and closing the door, ice maker called for water and appears to be functioning properly. Also replace both of the refrigerator door gaskets and they are sealing properly. All repairs complete."
We serviced a
KITCHENAID RANGE
Model KSEG950ESS6
Near Sisters, Oregon 97759
Levi
Job Details:
02/18/2026
"Replace control board element and sensor, tested and all tests are good."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Socorro, New Mexico 87801
Larry
Job Details:
02/18/2026
Installed timer and tested good - Unit is god to go - Survey mentioned
We serviced a
WHIRLPOOL COOKTOP
Model WCGK7036PS00
Near Los Lunas, New Mexico 87031
Larry
Job Details:
02/18/2026
Installed hinge and tesed good - Unit is good to go