We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Colorado Springs, CO 80924
Mathew
Job Details: 01/22/2024
"Found buzzing noise coming from main control. Replaced main control and test op, unit working as expected."
We serviced a
SAMSUNG DRYER
Model DVE53BB8700VA3
Near Colorado Springs, CO 80921
Mathew
Job Details: 01/22/2024
Replaced missing screw. Test op all okay.
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Colorado Springs, CO 80918
Mathew
Job Details: 01/22/2024
Found fault on high voltage side. Replaced capacitor and magnatron. Test op all okay
We serviced a
WHIRLPOOL WASHER
Model WTW7500GC2
Near Rio Rancho, NM 87144
Joe
Job Details: 01/22/2024
cx complant - the lid does not close/open properly and the washer can not lock and unlock - ins
We serviced a
SAMSUNG RESIDENTIAL REFR
Model RF30BB6200QLAA
Near Peyton, CO 80831
Brandon
Job Details: 01/22/2024
Replaced French assy and tested op all checks ok
We serviced a
THERMADOR REFRIGERATOR
Model T36IT71NNP/31
Near Colorado Springs, CO 80908
Jessie
Job Details: 01/22/2024
Replaced freezer inverter. Test op. Compressor took off and starting to cool. Customer to monitor for next 24 hours.
We serviced a
SAMSUNG WASHER
Model WA50R5200AW/US
Near Colorado Springs, CO 80928
Kris
Job Details: 01/22/2024
installed shifter ran test op all ok at this time.
We serviced a
WHIRLPOOL M/W OTR
Model WMH53521HZ06
Near Albuquerque, NM 87106
Larry
Job Details: 01/22/2024
CX complaint - Fan not working properly - Inspected unit and found a a loose harness at the control board to the fan - Secured connection and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Tajique, NM 87016
Jason
Job Details: 01/22/2024
installed suspension rods unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WFW87HEDW0
Near Albuquerque, NM 87106
Larry
Job Details: 01/22/2024
"CX complaint - Washer not starting error codes - Inspected unit and found F3E1, F1E2, F5E2, and F6E2 - Unit will need controls - CX does not want to bear the cost of repair and will replace - Collected SC on Tkt#-515843Control - $298.67Sensor - $64.50UI - $501.92 Parts - $865.90Labor - $219.95MSP - $17.50 Sub Total - $1,243.30 Tax - $105.68 Total - 1,348.98"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Albuquerque, NM 87110
Larry
Job Details: 01/22/2024
Installed switch and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ10
Near Albuquerque, NM 87111
Jason
Job Details: 01/22/2024
installed parts unit checks ok
We serviced a
GE RANGE
Model PHS93XYP6FS
Near Aspen, CO 81611
Erik
Job Details: 01/22/2024
install/test: GOODJOB COMPLETE
We serviced a
THERMADOR REFRIGERATOR
Model T36FT820NS/02
Near Aspen, CO 81611
Erik
Job Details: 01/22/2024
install parts/test: GOODcan take up to 24 hours to regulate tempsJOB COMPLETE
We serviced a
THERMADOR REFRIGERATOR
Model T30IR905SP/06
Near Snowmass, CO 81654
Erik
Job Details: 01/22/2024
install NTC sensor/test: *RUN TEST MODE*JOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Los Lunas, NM 87031
Larry
Job Details: 01/22/2024
CX complaint - Washer making buzzing noise - Inspected unit and ran diag cycle and could not duplicate issue - Unit is operating as designed
We serviced a
SPEEDQUEEN DRYER
Model ADE3LRGS171TW01
Near Colorado Springs, CO 80918
Mathew
Job Details: 01/22/2024
"Found timer switch not stopping dryer, arcing when cycle ends."
We serviced a
MONOGRAM DISHWASHER
Model ZDT925SPN7SS
Near Glenwood Springs, CO 81601
Erik
Job Details: 01/22/2024
install pump and MCB/ test: GOODJOB COMPLETE
We serviced a
MAYTAG WASHER
Model MVWB83DW4
Near Rio Rancho, NM 87124
Joe
Job Details: 01/22/2024
"cx complaint - loud noice during entire wash cycle, sounds like a jet taking off, knocking, grinding - inspected unit - could not duplicate issue but from comstomers description, gearcse is wearing out - customer declined any repair"
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Albuquerque, NM 87111
Jason
Job Details: 01/22/2024
installed support unit checks ok
We serviced a
WOLF RANGE
Model SRT366
Near Colorado Springs, CO 80904
Ralph
Job Details: 01/22/2024
"showed cust how to clean the burners, cust paid total autho no.C44CL9"
We serviced a
MAYTAG DRYER ELECTRIC
Model MED5500FW1
Near Peyton, CO 80831
Aaron
Job Details: 01/22/2024
"Rollers and idler have worn from use, unit is heating well at time of inspection, Needs repair kit. Repair kit 4392067 $76.48Tax $6.27Supplies $14.50Hc $129.95Labor $199.95Total job $427.1530 day estimate No return on parts Auth 129.95 hc #3H4U94"
We serviced a
SAMSUNG OTR MICROWAVE
Model ME17R7021ES/AA
Near Colorado Springs, CO 80908
Brandon
Job Details: 01/22/2024
"Magnetron had discoloration on tip, replaced magnetron and diode and tested op all checks ok"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ02
Near Colorado Springs, CO 80918
Glenn
Job Details: 01/22/2024
"Water has been dripping into Icemaker and has frozen up at Fill tube & Auger in bucket. Rear side of bucket auger gear slightly worn, may require new bucket. Off brand filter in use.Techline: (SR# 7738289524) Agrees that most likely off brand filter, causing water to leak. Suggest Manuf. Brand Filter > everydrop EDR4RXD1 , If once customer has defrosted the unit over night. with power off and doors left completely open during defrost, and then installed Manuf. brand water filter, if the problem continues, suggest replace > Fill tube - W11415785 $92.56 & Valve W11043013 $139.28 , Tax $19.01 , MPS $14.50 , Labor 239.95 , Declined Estimate for now, Paid SC Fee fo $149.95 , Autho#9P4UJVCustomer knows they have 30 days regaurding estimate"
We serviced a
JENN-AIR DISHWASHER
Model JDPSS245LX0
Near Sandia Park, NM 87047
Jason
Job Details: 01/22/2024
installed control unit checks ok
We serviced a
MAYTAG WASHER
Model MED6630HW
Near Avon, CO 81620
Antonio
Job Details: 01/22/2024
Found loose connection at dryers electrodes reconnected unit tested good
We serviced a
MAYTAG DRYER
Model MGD8000AG1
Near Edwards, CO 81632
Antonio
Job Details: 01/22/2024
Found bad iderler pully. Installed new dryer kit. Unit tested good Sc $149.95Lb$189.95Parts $80.19Total$420.09 $420.09 CK Auth# 49V39P; used 1 4392067 (Dryer kit) from stock
We serviced a
SUBZERO REFRIGERATOR
Model 700TCI
Near Colorado Springs, CO 80906
Ralph
Job Details: 01/22/2024
unit is draining properly now
We serviced a
SAMSUNG GAS RANGE
Model NX60A6511SS/AA
Near Colorado Springs, CO 80924
Mathew
Job Details: 01/22/2024
Replaced faulty spark module. Test op all okay.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHV00
Near Rifle, CO 81650
James R
Job Details: 01/22/2024
Printed labels took pics ready to send.
We serviced a
KITCHENAID REFRIGERATOR
Model KSSS42QDX04
Near Colorado Springs, CO 80904
David
Job Details: 01/22/2024
Found leak in water line to icemaker Repaired water line
We serviced a
SAMSUNG DISHWASHER
Model DW80B7070US/AA
Near Monument, CO 80132
Mathew
Job Details: 01/22/2024
Replaced wire harness and test op all okay.
We serviced a
WHIRLPOOL REFRIGERATOR
Model GD5SHAXLQ01
Near Colorado Springs, CO 80907
David
Job Details: 01/22/2024
"Checked refrigerator Refrigerator Working, cooling good.Good frost pattern, good air flow condenser, very plugged with lint, vacuumed and now has much better air flow Called customer and explained what I done. Somebody in the past had put a Supco hard start device on."
We serviced a
SAMSUNG DRYER ELECTRIC
Model dve45n5300w/a3I
Near Colorado Springs, CO 80922
Jessie
Job Details: 01/22/2024
Bad heater.Heater#dc97-14486a$282.50Tax $23.17Sc $129.95$14.50Labor $189.95Total $640.07No return on partsCustomer declines
We serviced a
WHIRLPOOL DRYER
Model WHD560CHW2
Near Vail, CO 81657
Antonio
Job Details: 01/22/2024
Found air cartridge not properly installed removed lint installed cartridge right unit tested good
We serviced a
WHIRLPOOL WASHER
Model WET4027HW1
Near Avon, CO 81620
Antonio
Job Details: 01/22/2024
Found cut wirers at capacitor spliceded back together unit tested good Sc$14995Lb$189.95$489.85 CC Auth# R93XA9
We serviced a
BOSCH FRENCH DOOR REFR
Model B36CD50SNS/02
Near Pueblo, CO 81006
James
Job Details: 01/22/2024
"installed ordered parts tested ops all ckok, no errors, ice fan is operating and ice fill works with no leaks."
We serviced a
WHIRLPOOL WASHER TOP LOAD
Model WTW4816FW
Near Pueblo, CO 81003
James
Job Details: 01/22/2024
unit is being used in commercial setting. unit has been abused. no model or serial number present on unit. talked with AR and found out whirlpool has extremely limited warranty on commercial use residential appliances. advised cust that no repair could be done and walked away per AR
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM02
Near Colorado Springs, CO 80903
Roman
Job Details: 01/22/2024
"Installed new back cover, sealant and air duct, ran fridge through diagnostics and it did not make the noise. Ran it in during the regular cycle and listened for a noise and it did not make noise other then the compressor and fans."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, CO 80903
Roman
Job Details: 01/22/2024
Hot and cold water lines are not on the correct valves. Swapped them and ran diagnostics on the washer. Washer filling and running correctly. Washer working great.
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Colorado Springs, CO 80903
Carlos
Job Details: 01/22/2024
"Installed UI, Control Board and Water valve. All codes are clear, hot water works, runs cycle ok."
We serviced a
MAYTAG DISHWASHER
Model MDB6000AWB
Near Colorado Springs, CO 80904
Carlos
Job Details: 01/22/2024
"Installed Door links, all ok cx paid labor $179.95 CK Auth# 494HL4"
We serviced a
SAMSUNG MICROWAVE
Model ME19CB704112AA
Near Colorado Springs, CO 80923
Mathew
Job Details: 01/22/2024
"Replaced door. No longer binds up but microwave door is misaligned, called techline to troubleshoot."
We serviced a
KITCHENAID REFRIGERATOR
Model KBFN506ESS01
Near Colorado Springs, CO 80906
Roman
Job Details: 01/22/2024
Installed new board and all leds are lit in ff and freezer. Fridge fans and compressor kicked on and working. Paid labor $$169.95 CC Auth# LF9M3N
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Grand Junction, CO 81504
James R
Job Details: 01/22/2024
Signed disclaimer. Put into service diagnostics no error codes. Tilted unit back Removed cover from pulleys belt is loose slipping. Squeals replaced. W11239857 Calibrated unit. Did a quick service diagnostics came back with no errors. Ok. Unit is draining good. Lid lock is working. Unit is operating as should.; used 1 W11239857 (Belt (Washer)) from stock
We serviced a
KITCHENAID WALLOVEN
Model KODE500ESS02
Near Colorado Springs, CO 80906
Carlos
Job Details: 01/22/2024
"Installed UI and control board. Ran test, runs ok UI registers inputs ok. Cx paid Labor $209.95 CC Auth# 4N39C9"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HZ09
Near Grand Junction, CO 81504
James R
Job Details: 01/22/2024
Customer signed disclaimer.Checked fuse was blown. Checked for a short none. Checked for proper Checked door switches all checked ok. checked wiring all looks good. Checked light and turntable all looks good. Checked amperage draw with unit heating 15.96 good. Ran unit for at least 10 minutes no issues. Replaced fuse. WPM0805101 Called tech line. 7738294755 Agrees with findings. Unit is working as should. Please fill out whirlpool tech satisfaction survey. Thank You.; used 1 WPM0805101 (20A Fuse) from stock
We serviced a
SAMSUNG DRYER
Model DV45H7000EW/A2
Near Colorado Springs, CO 80920
Kris
Job Details: 01/22/2024
cx deciding on repairs.heater assy dc97-14486a 282.50rollers idler dc97-16782e all 4 164.34idler dc96-00882f 200.46
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ1
Near Peyton, CO 80831
Aaron
Job Details: 01/22/2024
Unit uninstalled in living room with another unit installed. Removed and replaced motor sump assembly. Advised customer of 5 star survey.
We serviced a
MAYTAG DRYER
Model MED5030MW0
Near Rifle, CO 81650
James R
Job Details: 01/19/2024
Printed labels took pics ready to send.
We serviced a
BOSCH DISHWASHER
Model SHV78B73UC/38
Near Carbondale, CO 81623
Erik
Job Details: 01/19/2024
install heat pumpJOB COMPLETE
We serviced a
MAYTAG WASHER
Model MHN30PDBWW0
Near Colorado Springs, CO 80915
Roman
Job Details: 01/19/2024
"Removed old inlet valve and installed new one, checked for leaks. Ran the washer and waited till it did a full cycle. Error code did not come up through a cycle. Washer working great. Paid labor $179.95 CC Auth# T3XP3U"
We serviced a
MAYTAG DRYER
Model MED7230HW0
Near Colorado Springs, CO 80911
Roman
Job Details: 01/19/2024
"Removed old heater and high limit thermostat. Installed new element, thermostat and deep cleaned. Put the dryer back together and tested it, dryer heating up and working great."
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ1
Near Colorado Springs, CO 80922
Jerimiah
Job Details: 01/19/2024
Center griddle burner was not igniting. Found burner head dirty. And igniter needs cleaning. Wanted information about replacement knobs as well since they are falling apart. W11159630 knob $96.14
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Edgewood, NM 87015
Jason
Job Details: 01/19/2024
installed inlet assy unit checks ok
We serviced a
WOLF VENT HOODS
Model L522212
Near Colorado Springs, CO 80921
Kris
Job Details: 01/19/2024
ran test op all bulbs were stuck pulled all bulbs for cx. all ok at this time.
We serviced a
SAMSUNG GAS RANGE
Model NX60A6511SS/AA
Near Colorado Springs, CO 80907
Jerimiah
Job Details: 01/19/2024
"Display is dead, techline says needs display and control board replaced, Cust will look for new appliance. Labor would have been $169.95. $142.95 CC Auth# NRYC49DG94-04041B control board $272.06DG92-01232A display $269.58"
We serviced a
SUBZERO REFRIGERATOR
Model IC-30RID-RH
Near Colorado Springs, CO 80906
Ralph
Job Details: 01/19/2024
"unit is still under full warranty, cust says unit popping breaker, this is a fridge and nex to it is thefreezwee, both units are plugged into the same breaker and breaker is either a gfci or anarc fault, so will cust ccould here bill from tech support say bboth units need to have its own outlet and on dedicated breakers, we also checked for errors and found no errors, complerted call"
We serviced a
WHIRLPOOL WASHER TOP LOAD
Model WTW8000BW0I
Near Colorado Springs, CO 80906
Roman
Job Details: 01/19/2024
"Noticed the washer was way out of balance, ran it and the lid lock was not locking the first try, ran it a few more times and washer did not squeak or have an issue with the lid lock. Cx mentioned they had water line freezing and freezing inside the washer. Would not recommend using the washer when its really cold without making sure the lines and anything else is not frozen. Adjusted the washer and leveled it. Ran it again and did not have any other issue happen. Drain pump is making a rattling noise and could have been damaged when it froze but is pumping out water very well. Lid lock #WPW10619844 $138.96Card for sc did not go through"
We serviced a
SAMSUNG MICROWAVE
Model ME21A706BQN/AA
Near Colorado Springs, CO 80905
David
Job Details: 01/19/2024
Replaced magnetronTested and heating good
We serviced a
WHIRLPOOL WASHER
Model WFW5620HW2
Near Colorado Springs, CO 80921
Kris
Job Details: 01/19/2024
units ui doesn not respond load and go dispenser sensor is not registering. will need listed parts befroe i can make a determination if unit has any other issues.W11322903 298.67W11458345 194.44
We serviced a
SHARP MICROWAVE
Model R-530ES-T
Near Colorado Springs, CO 80904
David
Job Details: 01/19/2024
Installed turn table motor Tested and working good
We serviced a
MAYTAG DRYER
Model MED5030MW0
Near Grand Junction, CO 81504
James R
Job Details: 01/19/2024
Replaced white console and elec. contol assy. operation is normal. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
GE DRYER
Model HTX24EASKWSMTM
Near Colorado Springs, CO 80906
Roman
Job Details: 01/19/2024
"Removed the old heater and heater wire, installed thermostats onto the new heater and installed upgraded wire. Put the dryer back together and tested it. Dryer is heating up and working great."
We serviced a
KITCHENAID OTR MICROWAVE
Model KMHS120ESS-09
Near Colorado Springs, CO 80907
Ralph
Job Details: 01/19/2024
"rocker narm did not reset when door was open , remeedied the issue and unit checked okay...,autho no. N939KK"
We serviced a
KITCHENAID RANGE
Model KSEG700ESS6
Near Colorado Springs, CO 80917
Glenn
Job Details: 01/19/2024
"f8e0 - Cooling Fan Speed Too LowFound both connections to cooling motor unplugged and harness laying completely on opposite side of unit?! Appears that it was never plugged in? Re-assembled unit, All OPS Test:OK. Pre-heated oven to 325F Convection Bake. All OPS Test:OK"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, CO 80923
Glenn
Job Details: 01/19/2024
"Install New Gearcase, Block, Spanner Nut, Cam Kit, Shifter & Belt. Calibrate Unit, Diag Test:OK , Ran Quick Cycle > Pass"
We serviced a
MAYTAG WASHER
Model MVWB865GW0
Near Grand Junction, CO 81505
James R
Job Details: 01/19/2024
F0E3 overloadF0E5 off balanced loadF7E9 lock rotorCleared all codes. Run service diagnostics test no error codes returned. test 51 Found something between agitatitor. Removed. Test agitate cycle grinding gone. ok. Checked under unit. Looks good. Also did test 52 load size calibration cycle ok. Put into test 14 agitate sounds fine. Test 12 high speed spin ok. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDBM00
Near Grand Junction, CO 81507
James R
Job Details: 01/19/2024
Checked freezer temp. Unit is -6 plenty cold enough to make ice. Removed icemaker dumped old ice then reinstalled ice tray unit cycled out ice and filled with water. Is indicating that icemaker cycles and puts in water. May have been that icemaker bale arm was hitting what ice was in the tray. So the arm was up so it wouldnt make ice. At this point unit appears to be working properly. Customer will let us know if further issues. Paid service call $149.95 auth code. C44KR3Please fill out whirlpool tech satisfaction survey. Thank You. Put into diagnostics test 36 icebox fan comes on test 37 icebox thermistor passes shows good. Test 3 indicates fan motor and air baffle motor are working.
We serviced a
COVE DISHWASHER
Model DW2450WS
Near Colorado Springs, CO 80906
Roman
Job Details: 01/19/2024
"Error code is for a fill issue, ran the dw and it started filling slowly and then fully started filling indicating the pipes were slightly frozen. Recommend keeping an eye on it when running in cold temperatures. Dw is working fine otherwise all three spray arms are spinning."
We serviced a
WHIRLPOOL DRYER
Model WED49STBW
Near Peyton, CO 80831
Aaron
Job Details: 01/19/2024
"Thermal fuse shorted out, removed and replaced fuse, tested, working and heating well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM06
Near Colorado Springs, CO 80922
Aaron
Job Details: 01/19/2024
"Dent and scratches on RC door, removed and replaced door, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Colorado Springs, CO 80910
Carlos
Job Details: 01/19/2024
"Installed control board, ran test, runs ok."
We serviced a
KITCHENAID RANGE
Model KFGD500ESS00
Near Colorado Springs, CO 80905
Carlos
Job Details: 01/19/2024
"Installed igniter, ran test op all ok cx paid labor $189.95 CC Auth# 9LLPE4"
We serviced a
WHIRLPOOL RANGE
Model WFE320M0JS3
Near Colorado Springs, CO 80922
Aaron
Job Details: 01/19/2024
"Large scratch on cooktop, removed and replaced top, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHV08
Near Albuquerque, NM 87123
Jason
Job Details: 01/19/2024
installed door unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM06
Near Colorado Springs, CO 80922
Aaron
Job Details: 01/19/2024
"Dents on both doors, removed and replaced doors, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031UG/AA
Near Fountain, CO 80817
Mathew
Job Details: 01/19/2024
Found bad seal on drain pump causing leak and LC code. Replaced drain pump and test op all okay.
We serviced a
JENNAIR REFRIGERATOR
Model JFX2897DRP02
Near Grand Junction, CO 81507
James R
Job Details: 01/19/2024
Replaced all lights some of the lights on F.F. area were glued in was quite a ordeal to remove. All are working. Customer paid $149.95 Labor auth code VPP3JY Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MHW5630HC2
Near Colorado Springs, CO 80922
Aaron
Job Details: 01/19/2024
"Debris clogging inlet valve, cleared and tested unit, working well now. Advised customer that water supply to unit is on an outside wall as well, potentially freezing the lines in extreme cold. Advised customer of 5 star survey."
We serviced a
SAMSUNG MICROWAVE
Model ME17R7021EB/AA
Near Colorado Springs, CO 80906
Mathew
Job Details: 01/19/2024
Cx did not want me to perform any repairs on product. Got model/serial but Cx made it clear she only wanted a refund of faulty microwave. Microwave making buzzing noise indicative of bad transformer/ magnatron.
We serviced a
DACOR MICROWAVE OVEN
Model DCM24S
Near Colorado Springs, CO 80906
Mathew
Job Details: 01/19/2024
"Installed new outer panel of door. Reinstalled and test op, door still not aligned. Called dacor support. Sent agent pictures of issue, agent told me he will submit for review."
We serviced a
SAMSUNG WASHER
Model WA52A5500AV/US
Near Colorado Springs, CO 80910
Mathew
Job Details: 01/19/2024
"Found valves filling machine on test run, wires have continuity, main pcb test ok. Checked pressure sensor hose, found it not plugged in all the way to sensor. Test operated as expected. $129.95 CC Auth# ALL49VIf issue persists unit will need DC96-01703N"
We serviced a
KITCHENAID DISHWASHER
Model KDTM604KPS0
Near Colorado Springs, CO 80922
Aaron
Job Details: 01/19/2024
"Left door hinge is not properly engaging spring, corrected and tested unit. Advised customer of situation and survey."
We serviced a
GE REFRIGERATOR/TOP
Model GSS25GYPFCFS
Near Silverthorne, CO 80498
Erik
Job Details: 01/19/2024
refused service - already scheduled with Peak Appliance for Feb. 1stdidnt want me to service CANCEL SERVICE
We serviced a
SAMSUNG WASHER
Model WF50BG8300AVUS
Near Colorado Springs, CO 80907
Brandon
Job Details: 01/19/2024
Replaced weights and tested op all checks ok hass oqc passed
We serviced a
GE RANGE
Model JBS86SP1SS
Near Leadville, CO 80461
Erik
Job Details: 01/19/2024
GE TAG : 'replace cooktop and move forward with repair'please allow 24 hours (GE CX SERVICE TO APPLY CASE #)CX understands they maybe responsible for SC and/or LABOR costinstall cooktop $99.00service $189.95case#11758066
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031US/AA
Near Fountain, CO 80817
Brandon
Job Details: 01/19/2024
"Replaced water valve and tested op checked for leaks all ok, installed leak detection strip all checks ok hass not compatible"
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS20
Near Albuquerque, NM 87120
Larry
Job Details: 01/19/2024
CX complaint - Oven making weird noise - Inspected unit and found the cx is concerned about the sound of the fan kicking into high speed at the end af a baking cycle - Explained this is normal operation - Unit is operating as designed
We serviced a
WHIRLPOOL WALLOVEN
Model WOD52ES4MB0
Near Albuquerque, NM 87110
Jason
Job Details: 01/19/2024
installed console and fan motor unit checks ok
We serviced a
MAYTAG WASHER
Model MHW5500FW1
Near Albuquerque, NM 87106
Jason
Job Details: 01/19/2024
Installed control and pressure sensor unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ02
Near Albuquerque, NM 87105
Jason
Job Details: 01/19/2024
Installed parts listed unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Albuquerque, NM 87105
Larry
Job Details: 01/19/2024
Installed parts listed and tested good - Unit is good to go
We serviced a
SAMSUNG DRYER
Model DV42H5200EW/A3
Near Colorado Springs, CO 80915
Mathew
Job Details: 01/19/2024
Found roller clogged with hair. Cleaned all rollers and test op all okay. Svf 129.95 $129.95 CC Auth# XVM99R
We serviced a
WHIRLPOOL WASHER
Model WFW560CHW4
Near Rocky Ford, CO 81067
James
Job Details: 01/19/2024
installed ordered parts tested ops all ckok. left litmus
We serviced a
KITCHENAID COOKTOP
Model KCGS356ESS05
Near Larkspur, CO 80118
Glenn
Job Details: 01/19/2024
"Attempted installing switch assy twice, as I've ordered 6 of these with hope I can get one installed w/o it breaking. Both broke. Called Techline once again, referred to SR #7738087274. Sent multiple pics and suggested I try forcing the center switch on from the side. I was then successful in getting center switch in place, however one of the other switches was defective, as did not stop clicking once ignited and turned past ignite! Tried others. 4th attempted part install finally worked. (Note - previous visits were failed attepts with anoth 2 bad parts!) All OPS Test:OK"
We serviced a
MAYTAG FREEZER
Model MZF34X18FW06
Near Monument, CO 80132
Glenn
Job Details: 01/19/2024
"Unit is in garage which is not climate controlled. Temp in Garage is approx 38F at this time, perhaps way colder overnight. Frzr Product at: 17F > 19F , Reset connections to control. Techline: Suggest move unit inside to temps above 40F constantly. Otherwise, we cannot make proper diagnosis. Allow 4 days for unit to settle after it has been brought inside, before calling, if unit still having trouble, customer will then call back. SR# 7738278491"
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ1
Near Colorado Springs, CO 80923
Aaron
Job Details: 01/19/2024
"Console bottom trim came off, uses three screw and inserts to hold plastic up, corrected and secure, if problem reoccurs, would need new plastic inserts. Insert W11025100 $47.67 x3 inserts = $143.01Tax $11.73Supplies $14.50Hc $149.95Labor $189.95Total job $509.1430 day estimate No return on parts Auth 149.95 #3MUP44"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730PAHZ
Near Colorado Springs, CO 80915
Carlos
Job Details: 01/19/2024
Installed water valve ran test all ok
We serviced a
JENN-AIR DISHWASHER
Model JDPSS245LX0
Near Vail, CO 81657
Antonio
Job Details: 01/19/2024
Installed new door seal and inlet initvtested good also advised of water strips